Firmware upgrade encountered an issue. Pleasev recovety mode in Kies & try again - Galaxy S II Q&A, Help & Troubleshooting

I have a Galaxy 2 and a few days ago I charged cell phone and I when took out it from the charge the phone didnt turn on.
I tried reinstall the rom but the installation fails in ODIN.
I tried different ROMs but all failed.
I took to lab and they said the device was burned inside probably due to power charging.
But it is very strange that the device enters DOWNLOAD and when I turn the phone appears a message:
Firmware upgrade encountered an issue. Pleasev recovety mode in Kies & try again
Maybe something could be done to save the phone?
Thanks for helpers

I presume we're talking about an I9100 ?
The repair shop you took it to is probably wrong/doesn't know what they're talking about; think about it, if something was 'burnt out' on the motherboard, the phone wouldn't boot at all. However, with that said, it is possible the NAND could be corrupted, which is sometimes the case with these.
Find Hopper8'd 'Odin troubleshooting' thread stickied in General & try everything in that thread as many times as you have patience for/until you get a successful Odin flash, these cases are always fixed with persistence when they're actually recoverable (which is often the case when you still have download mode).
If you find after days of trying you can't get a successful flash, take it to another mobile repair shop. Most likely fix will be motherboard replacement as it's not feasible to just replace the NAND (very fiddly to do & would cost you more in labour than a motherboard replacement).

MistahBungle said:
I presume we're talking about an I9100 ?
The repair shop you took it to is probably wrong/doesn't know what they're talking about; think about it, if something was 'burnt out' on the motherboard, the phone wouldn't boot at all. However, with that said, it is possible the NAND could be corrupted, which is sometimes the case with these.
Find Hopper8'd 'Odin troubleshooting' thread stickied in General & try everything in that thread as many times as you have patience for/until you get a successful Odin flash, these cases are always fixed with persistence when they're actually recoverable (which is often the case when you still have download mode).
If you find after days of trying you can't get a successful flash, take it to another mobile repair shop. Most likely fix will be motherboard replacement as it's not feasible to just replace the NAND (very fiddly to do & would cost you more in labour than a motherboard replacement).
Click to expand...
Click to collapse
I all day tried to falsh still is fail.
There is another way?
Please help me

I just did help you. I gave you the only help you can give in this situation.
The only way you're fixing this yourself is with a successful flash, and if you can't get that done, take it to a Samsung service centre or back to one of those local mobile repair shops.
There is no magic fix and no other way for you to fix this.

MistahBungle said:
I just did help you. I gave you the only help you can give in this situation.
The only way you're fixing this yourself is with a successful flash, and if you can't get that done, take it to a Samsung service centre or back to one of those local mobile repair shops.
There is no magic fix and no other way for you to fix this.
Click to expand...
Click to collapse
There is any file that can be install by odin that will fix the phone? expect of rom

*cough*
Final time I'm saying it. I've given you the only way to fix this. If this doesn't fix it, you can't fix it yourself. What is it exactly do you find so difficult to understand about this ?
They're your choices. Persist & hope for the best, sit there with a busted phone for however long you want to be in denial, or get the motherboard replaced if you're unable to fix it yourself.

Related

[Q] Bricked my phone?

So I had previously rooted my SGSII, and decided to try installing CM7 on it. I used CWM Recovery and ran it off the SD card, and everything appeared to work fine. I think I had a bad/not fully functioning CWM or something, as it didn't list an option to backup anything (I'm guessing because I flashed the stock kernel after rooting?) Anyway, it will no longer boot. I can access download mode, but Odin fails everytime I try to flash anything back on there. When I try to boot my phone, I just get a "Firmware upgrade encountered an issue" error.
EDIT: I just tried again as I was writing this, after rebooting, reinstalling my drivers and rebooting my computer. I was able to get the Firmware to flash properly in Odin. Now I have my phone booting and getting stuck on the "Samsung Galaxy SII GT-I9100 splash screen... Doesn't seem to go any further than that though, unfortunately.
Any ideas what I can do? Is it possible that I need re-flash a bootloader or something ??
Any help would be supremely appreciated!
So I was just trying to re-install the Kernel, using the CF unsecured kernel, and it failed, but when I try to go into recovery mode, it looks as though it managed to install CWM Recovery. I have no idea what to do from here, and am sort of afraid to do anything for fear or bricking the phone completely...
I'm hoping someone out there knows how to fix this, I feel like such a tool
As long as you can get into download-mode, your phone isn't bricked.
If you switch from or to a TouchWiz-based ROM, you have to do a full-wipe in the recovery.
Sent from my GT-I9100 using XDA App
Go back to stock first via download mode via odin
Nah you're good. Similar thing happened to me at my first flashing attempt. Get your stock firmware from Intratech's thread, put the phone into download mode & flash the firmware via Odin.
Then maybe have another go at rooting the phone with the matching CFRoot kernel.
Porkchops said:
So I was just trying to re-install the Kernel, using the CF unsecured kernel, and it failed, but when I try to go into recovery mode, it looks as though it managed to install CWM Recovery. I have no idea what to do from here, and am sort of afraid to do anything for fear or bricking the phone completely...
I'm hoping someone out there knows how to fix this, I feel like such a tool
Click to expand...
Click to collapse
yes, if you can still go in download mode it's no so difficult..this "small brick" it's on of "Android things to do" once in your SGS2 life
Hi guys. I'm in a worst situation. As my phone after a failed ODIN downgrade from Android 2.3.6 to one stock kernel is completelly dead - it doesn't boot anymore - not even managed to put it back into download mode or revert to fact defaults (no keys, no lights not even battery charging displayed when pluged in) - tryed the USB jig also. Nothing worked.
The question is: Will Samsung manage to repair and how much will it cost - an average ammount offcourse. Because I guess it's out of the question to be considered a warranty issue. I guess it will be visible somebody have done smth to the ROM by a software approach....
This is the short story because I would bore you to discuss all the things I have been through - it was only my faoult out of stupidity
HELP!
I don't see why Samsung wouldn't fix it ? As to how much they'll charge you, I think you'll find that will vary from country to country (labour costs being variable, etc). No, I don't think you'll be able to have it repaired under warranty.
You might want to look at having it JTAG repaired by someone other than Samsung. This will possibly be cheaper than having Samsung repair it. Do a search on here/Google.
alexdonc said:
The question is: Will Samsung manage to repair and how much will it cost - an average ammount offcourse. Because I guess it's out of the question to be considered a warranty issue. I guess it will be visible somebody have done smth to the ROM by a software approach....
HELP!
Click to expand...
Click to collapse
Thank you very much. I have searched alot to actually understand - unfortunatelly for me it will cost... I saw on youtube a JTAG in action right now (cannot post the link yet). I understand now it is the only way. I'll keep you posted guys. Tomorrow I'll go to service.
I'm sorry it's going to cost Alex. A difficult thing to happen, I know
Here's a link for a JTAG repairer in the US who is also a member here, tho I see you've already found one. I'm sure doing it this way will be cheaper/probably faster than having Samsung do the repair as well.
alexdonc said:
Thank you very much. I have searched alot to actually understand - unfortunatelly for me it will cost... I saw on youtube a JTAG in action right now (cannot post the link yet). I understand now it is the only way. I'll keep you posted guys. Tomorrow I'll go to service.
Click to expand...
Click to collapse
Thax. Funny thing is that this is exactly the thing I found - the same mobiletechvideos in US Now I allready have an ideea of how much should cost that. Hopefully I'll find a local GSM repair shop with the posibilitty to unbrick it cheep - or at least not much than 50USD - in local currency ofcource.
I'm still thinking if it is possible to use an ATMEL copy process - like in the old times for EEPROMS - I have done that in the past. In theory it might work but I will never do it - alredy scared about what happened to my beloved droid.
Thx again Mistah and have a gr8 day and a wonderfull new 2012!
Yeah I've seen a report or two on here from people who have used his service & have been happy. Must admit I found his page when thought I'd bricked my phone after my first flash attempt messed up. Yeah you might be able to get it done cheaper somewhere local, and that will mean less time without the phone for you without the phone in mail from you to the US & back again.
Let us know how you get on, your experience will be a good guide for people in future who have the same problems as you.
No probs man, happy to give you the little help I did. You too Alex Hope you have a great year & you get your phone back & working soon
alexdonc said:
Thax. Funny thing is that this is exactly the thing I found - the same mobiletechvideos in US Now I allready have an ideea of how much should cost that. Hopefully I'll find a local GSM repair shop with the posibilitty to unbrick it cheep - or at least not much than 50USD - in local currency ofcource.
I'm still thinking if it is possible to use an ATMEL copy process - like in the old times for EEPROMS - I have done that in the past. In theory it might work but I will never do it - alredy scared about what happened to my beloved droid.
Thx again Mistah and have a gr8 day and a wonderfull new 2012!
Click to expand...
Click to collapse
Hello again. Solved right now. The service didn't charged me at all - I was kind of lucky after all. Unfortunately there are still some issues I have from the start. I'll keep on digging - software related.

[Q] [HELP] ClockWorkMod backup bricked my phone??

hi everybody!
all the steps below were taken from galaxys2root.com as well as the files
i have i9100 with a stock rom 2.3.4 (ki4) (and 1.4gb of free memory-maybe that was the problem).
yesterday i rooted it (everything was fine) and then i installed CWM recovery 4.0.1.4 through odin v1.85 (went fine too) and then on my way to find myself a new rom i decided to backup my current one with cwm. then i entered cwm by pressing vol-down+pwr+home and hit "backup". it backed up the system and then moved on to the data and thats where it got stuck for like an hour.... from the guide i understood that it shouldnt take more than 10 min- 15 min top so i figured that im having a problem, i tuned off the phone by pressing pwr button and turn it back on, then the phone got stuck on the sgs2 screen with the triangle so i turned it off again----> this time it didnt came back on, and not responding to download mode neither to polling battery out or not even by connecting to usb and charger- just dead!
how is it possible? and what should i do to bring it back to life? (and myself)
thank you very much(please help...), and sorry for the long text and the bad english
do you have usb jig with you?
i assume you brick your phone.
read my thread http://forum.xda-developers.com/showthread.php?t=1402286 carefully. anyway, usb jig will not harm your device
No download mode = try jig. Jig doesn't work = JTAG repair by 3rd party repairer (cheaper option) or JTAG repair my Samsung (more expensive option).
thank you,
no dont have one but i ordered from ebay.
is there a chance that my battery died and as a result of the two my phone wont respond?
Possible but highly unlikely. I guess you might as well try a new battery, at worst you'll have a spare when you get the phone repaired.
Fairly common problem go to forum xx download something and follow the instructions dont work go to a totally different forum and ask why ???
CWM 4 very old .
vol-down+pwr+home and hit "backup why ??? thats download mode
My guess would be wrong instructions/firmware .
The other question to ask is it a i9100 or a different version .
jje
i really hope thats the problem, im going to a friend now to try with his battry.
but really how is it possible that my phone is bricked when i didnt even try to flash a new rom, and more than that it happened in the backup process when all the cwm does is a copy operation... so what really had happened?
JJEgan said:
Fairly common problem go to forum xx download something and follow the instructions dont work go to a totally different forum and ask why ???
CWM 4 very old .
vol-down+pwr+home and hit "backup why ??? thats download mode
My guess would be wrong instructions/firmware .
The other question to ask is it a i9100 or a different version .
jje
Click to expand...
Click to collapse
to be honest i was too lazy to search here (which im not going to be now)
thats what he was doing in the video (it did went in cwm)
and my phone is i9100 i bought it in the UK
Wrong firmware faulty firmware wrong instructions any number of things can go wrong with a flash . But it is very odd that it happens in backup recovery yes but backup very rare .
jje
JJEgan said:
Wrong firmware faulty firmware wrong instructions any number of things can go wrong with a flash . But it is very odd that it happens in backup recovery yes but backup very rare .
jje
Click to expand...
Click to collapse
so there is a slight chance that its the battery right?
IIIMJRIII said:
so there is a slight chance that its the battery right?
Click to expand...
Click to collapse
no, there is not.
Sent from my GT-I9100 using xda premium
ok the battery swap doesnt work so its not the problem,
any other ideas??? (except usb jig and jtag)
thanks
Jig <=1% chance of getting you into download mode, JTAG = 100% chance of fixing it. Other options = 0.
MistahBungle said:
Jig <=1% chance of getting you into download mode, JTAG = 100% chance of fixing it. Other options = 0.
Click to expand...
Click to collapse
I should say jog = 50% chances of getting into download mode. JTAG is more like a solution for hard brick(totally unresponsive, bootloader totally mess up, brain system totally corrupted).
Base on my understanding, getting yourself a hard brick is harder than finding a needle in a haystack. If you go through zedomax(galaxys2root.com owner), he mentioned that he flashed all his android device countless time. All he got is just a couple of soft brick. Never a hard brick. Don't waste your money first. Invest on a cheap usb jig which only cost around 2 dollar, compare to JTAG services which cost 50 dollar.
If usb jig doesn't work, try to go for warranty , see whether they charge you or not. If warranty doesn't cover you and cost less than 50 dollar to repair, go for it.
Only go for JTAG if every effort above don't work.
Warning: JTAG is just a service that reinject Samsung firmware into your device. If your phone has hardware failure, I don't think they can help. Unless they provide hardware repair now. If you wanna be sure, email or call them up to see if they provide hardware repair/replace as well, just in case it is a hardware failure cases.
Sent from my GT-I9100 using xda premium
i know its a very rare situation but it happened. I've tried the jig and it didnt work, then i decided to send it back to the store and they told me they have sent it to the manufacturer, now im waiting...

Phone bricked, download mode works but no flashing is possible

Hi there!
Actually, I've stopped trying to ressurect my phone about a month ago, but... maybe someone can help
Ok, what happened:
I was at exam and must shut my phone off. I did it. Some seconds later it booted again. So, I had to turn it off by holding the power button. After that it doesn't boot anymore.
Now the "facts":
- It was the Lite'ning Rom (I think 2.6) with the Kernel incl. as it bricked.
- It boots up to the yellow triangle and stops there.
- If I want to charge it - I see just a waiting-circle (like in windows), but it doesn't move at all.
- I can enter the Download mode, but only if I hold Volume Down + Power Button. If I hold the VolumeDown+Home+Power Button - it's just starting without entering the download mode.
- I can't enter the recovery mode. It's just gone...
- Kies doesn't see the phone at all.
- Odin see it and I can flash it. I can flash all the things I want: bootloader, kernel, pda. I can re-partition it, BUT:
- Now the interresting thing: Odin flash it and says, that all was fine. But nothing happens... Actually, I've already tried to "kill" it with the 3-part ROM for 9100G, but Odin says, that all was ok and nothing happens with the phone at all. It just ignoring all the flashs I tried.
- I have the USB-Jig, but it start the "Factory mode", and... see the point above.
- Already tried about 10-15 Rom (1-parted and 3-parted), with bootloaders and pits etc. Nothing happens.
I had the phone just for 3 months, and... yeah, 500€ are gone. I can't send it to Samsung service, because of triangle and counter > 0. And I can't remove this triangle and set the counter back.
Anyone have any ideas I can try? Maybe someone already heard about issue like that? Is it the famous "eMMC brick"?
Thx in advance!
I don't know if this is due to the EMMC bug. But it sure does sound like a hardware issue.
Have you tried flashing Factory / Stock firmware via Odin? I had a similar issue some time back with my Galaxy Tab but flashing stock firmware, rebooting to recovery and clearing cache etc then fixed the issue.
Good luck man!
Maybe send it in for warranty service/replacement & play dumb in the first instance. Always a chance they won't care/notice you trashed it. If they do & decide to charge you, ask for a quote & for the phone back. Then take the phone to local mobile repair shops & see how much they want for repairing the phone. You can also then compare the costs of having Samsung/authorised repairer or local mobile repair shops with the costs of having the phone JTAG'd (assuming it can be JTAG'd). Lots of JTAG repairers can be found with a Google search, not necessarily in your country, but will still likely be cheaper than having Samsung/authorised repairer fix it.
Try to flash a bootloader for a different device (Note for example), and after that to repartion the device also with pit for Note or something similar. I think that there is a good chance that you succeed in killing the phone completely, and then you can send it to service and play dumb.
Find someone with a riff box and get it j-taged
Sent from my GT-I9100 using Tapatalk 2
A331709 said:
Have you tried flashing Factory / Stock firmware via Odin?
Click to expand...
Click to collapse
Yes, already tried some different stock firmwares, always the same thing - just nothing happens and Odin is lucky and saying "all was fine".
pilgrim011 said:
Try to flash a bootloader for a different device (Note for example), and after that to repartion the device also with pit for Note or something similar. I think that there is a good chance that you succeed in killing the phone completely, and then you can send it to service and play dumb.
Click to expand...
Click to collapse
Already tried with G-Version of SGS2, but that didn't work. But I will try it with Note's bootloader and pit. Thx!
MistahBungle said:
Maybe send it in for warranty service/replacement & play dumb in the first instance. Always a chance they won't care/notice you trashed it. If they do & decide to charge you, ask for a quote & for the phone back. Then take the phone to local mobile repair shops & see how much they want for repairing the phone. You can also then compare the costs of having Samsung/authorised repairer or local mobile repair shops with the costs of having the phone JTAG'd (assuming it can be JTAG'd). Lots of JTAG repairers can be found with a Google search, not necessarily in your country, but will still likely be cheaper than having Samsung/authorised repairer fix it.
Click to expand...
Click to collapse
I've already called JTAG-Service I found in my country, but the guy on the phone said "you can send it to us, we will try to fix the issue, but you will see - you will get your device back without any changes." In addition, he said, that my phone has some bad sectors in header of internal memory and it's nothing to do with it. The only option is to change the mainboard.
I'll try to kill it with Note's firmware, if it's not going to work - will try to send it for repair. But the chance, that guys from samsung will ignore the triangle and counter ist actually... yeah, it low ^^
Thx again for the advices!
//edit:
tried the Note's bootloaders - the phone accept it, I see the progress-bar on phone's screen, but after reboot it stucks again on triangle.
tried this guide again - doesn' help at all.
looks like the advice from MistahBungle is the last hope

[Q] Help Phone not starting up !!! Urgent

Hello Guys,
I own a Galaxy S2 I9100G.. 2 months ago i flashed it and installed custom Rom of cyanogen mod version 10.1.3-RC2-i9100g ...
Last night i was browsing the internet when suddenly it got stuck and i had remove the battery to restart. But the problem is that it didnt restart.
I can only go in to download mode. But cant seem to flash via odin it fails atfer nand write. And i am not able to find the files for my mobile..as many files here were on hotfile server and it seems to have been closed.
Please help me regarding this matter how should i proceed?? how do i get it to start ??
Last resort would be to go the service center but i would like to try to fix it before.. And warranty also expired a while back ..
I get complete ( write) operation fail after nand write..
do u think my hardware has blown up or something ?? or is it just sofware problem ?
I am using odin V 3.04 .. On odin version 1.85 it usually doeant go on after nand write and stays on it ..
Please help me here .. I really would like to fix my phone : (
Can't you go to Recovery using Volume Up+Home+Power ? the symptoms you are telling are kinda dangerous. At what stage the Odin flashing fails? if its at the factoryfs, than i am afraid you are facing a super brick here.
Look for firmware on AndroidFirmwares.net or Samsung-Updates.com, you don't need to use the exact same firmware that was originally on the phone, any firmware for your carrier will do (make sure it's I9100G though) & if you're going to go back to a custom rom as soon as you get your phone working normally again, any firmware from any carrier will do.
Search for Hopper8's 'Odin troubleshooting' thread, though some of the stuff he mentions is I9100 specific (advice to flash specific files) a lot of the other stuff is generic I9100x stuff which you should try if you find you can't get a successful Odin flash.
But if it keeps failing at NAND write having tried a lot of different I9100G stock firmwares, the NAND might be cactus, which means you need a motherboard replacement. But I'd try a lot of stock roms before I conceded that if I were in your situation. Often these things can be fixed by persevering.
@alvinasnow Nope i cant go into recovery mode.. If i could it would have been very easy after then.. Only download mode opens up.. And i tried different things flashing bootloader, kernel, firmware, pit,csc , everything fails at nand writing .. So is there a way out of this ??
@MistahBungle I was afraid that might be the answer motherboard replacement.. I tried different firmwares and even flashing via different Methods but its always the same.. i will go to the sites you mentioned to try more firmwares..
But i think my only option would be to go to a samsung service center i guess :-/ ?? they would be able to fix it right ???
ZiadNasir said:
@alvinasnow Nope i cant go into recovery mode.. If i could it would have been very easy after then.. Only download mode opens up.. And i tried different things flashing bootloader, kernel, firmware, pit,csc , everything fails at nand writing .. So is there a way out of this ??
@MistahBungle I was afraid that might be the answer motherboard replacement.. I tried different firmwares and even flashing via different Methods but its always the same.. i will go to the sites you mentioned to try more firmwares..
But i think my only option would be to go to a samsung service center i guess :-/ ?? they would be able to fix it right ???
Click to expand...
Click to collapse
Yep, but it's cheaper, faster and very easy to do it yourself
Inviato dal mio GT-I9100
Yep. Sourcing a 2nd hand motherboard online somewhere & either replacing yourself or paying a local mobile repair shop (non Samsung service centre) to replace will be much cheaper than paying a service centre to put a new board in.
So Basically there is no way to save my internal memory data :-/ ????
Changing the motherboard i guess would mean all gone with not a single hope of recovery.. OR i get to keep my data after the change ??
If you didn't back your data up, no. I guess you could contact companies who recover data from dead hard drives & maybe they can help, but that's a real longshot & will be very expensive if it's possible.
I did one back up 50-55 days ago when i went to custom rom .. so i will be losing pretty much only data in last month or so .. not much ..
But i still dont understand why the motherboard needs to be changed ?? i mean the download mode opens and everything .. odin fails to write ..
So nand failure basically means motherboard got screwed??
Are there other flashing softwares better then odin ??
I will have to actually wait till tomorrow to see what does samsung has to say in this regard as its off today ..So thought one last fight lol ..
And one more thing the battery is draining really fast and pretty much heating up in minutes when i put it on charge ..
And when i remove the charger .. the charging battery logo does not disappear i have to remove battery for it to disappear.. and the logo also stays when i remove the battery while the charger is still connected ..so have to remove the charger to make it go away .. basically cut all power for the logo to go away ..
As I said in my first post to this thread, you might as well keep trying/flashing firmwares, but you claimed to have already done a lot of that. What you're describing is symptomatic of the NAND being corrupted. It's too time consuming for service centres to replace just the NAND (removing/re-soldering components like that is fiddly), so they simply replace the whole board (and charge you a lot to do it).
OK...That extra information you supplied in your last post might give you an easier/cheaper fix. What you've just described sounds a lot like the USB board/port is on its way out. Replacing this yourself is cheap & easy to do (you just have to wait for the part to be delivered once you order it online); there's a guide in the General section which has all the info you need (search for replace USB charger board). Do that, then see if you can get a successful Odin flash. If you can, happy days. If you can't, then you replace the motherboard one way or another (or get a new phone).
This may or may not fix your problem; it may be a case of the NAND corrupted and the USB board needing replacing, but you're only going to know if you replace the board first.
You may fol a link in my signature for revival of ur phone.
From the OP: 'I can only go in to download mode'.
alvinasnow said:
You may fol a link in my signature for revival of ur phone.
Click to expand...
Click to collapse
MistahBungle said:
From the OP: 'I can only go in to download mode'.
Click to expand...
Click to collapse
flash stock
^^^^^
Did you not read the OP/rest of the thread as well ? He tried to do that on a number of occasions, but something was tripping him up.
Initially it seemed fairly obvious it was likely NAND corruption, though in the OP's last post to this thread, the things he mentioned suggested a faulty USB board may have been stopping him getting a successful Odin flash.
So it was suggested he replace that given how cheap it is to do, and to try flashing stock again. That was a week ago, and depending on where in the world the OP is, he may well be still waiting for the part to arrive.
Actually i got confused bcoz he again told he can boot in download mode then his mother board cant b faulty its the usb port maybe
Sent from my C6502 using xda app-developers app

[Q] i9100 Bricked. need help

My sotry: Had Cm10.2, this morning it updated/reseted itself (on its own) and battery died while doing it.
Tried recovering to older backup - stuck in boot img. - no more recovery mod.
Odin - official 4.1.2 - bootloop
Recovery mod - clear cache - error message: could not mount /cache, and /cache not found red error messages
Odin with another file - stuck in NAND write start - no more recovery from this point.
Tried with different .pit and other files.. still stuck in there.
Last try was to try to re-partition with 2.3.6 fw. FAILED.
Now the phone won't start. I tried different methods like jumpstart it and holding different button configurations, without battery etc etc and nothing worked (or i did them wrong).
@ this moment i am trying to avoid services. So please any help will do.
Service centre = replace motherboard with new motherboard, or you source 2nd hand board yourself & either replace yourself or pay local mobile repair (non-service centre) shop to swap, or new phone.
There's nothing anyone here can suggest, your phone is Donald.
MistahBungle said:
Service centre = replace motherboard with new motherboard, or you source 2nd hand board yourself & either replace yourself or pay local mobile repair (non-service centre) shop to swap, or new phone.
There's nothing anyone here can suggest, your phone is Donald.
Click to expand...
Click to collapse
But how do you know it's the MB? maybe it could be restored, as seen in many cases on the internet.
ferydaboss said:
But how do you know it's the MB? maybe it could be restored, as seen in many cases on the internet.
Click to expand...
Click to collapse
see of your phone to local repair shop or to sammy care if still have warranty..
Because I've seen thousands of cases exactly like this over the past 2 & a bit yrs on here, and they've all ended up exactly the same.
But if you want to sit around without a phone for a week/two weeks/a month/whatever, don't let me stop you.
MistahBungle said:
Because I've seen thousands of cases exactly like this over the past 2 & a bit yrs on here, and they've all ended up exactly the same.
But if you want to sit around without a phone for a week/two weeks/a month/whatever, don't let me stop you.
Click to expand...
Click to collapse
If your have ended up like this ???

Categories

Resources