[Q] ZTE Midnight (Z768G) Boot issues - Android Q&A, Help & Troubleshooting

I rooted this phone and used link2sd to move some apps and free up internal memory. I think I moved the dialer app to sd, and shortly after the phone crashed, and restarting it was stuck in a boot loop. I went into recovery mode and did a factory reset. After doing this, it would make it all the way to the Welcome to Z768G screen. It says "Touch the android to begin" and has two buttons at the bottom, Emergency Dial and Change Language. When I touch the android it seems to react to my touch, but nothing happens. If I push Emergency Dial, an error message pops up that says "The application Setup Wizard(process com.android.setupwizard) has stopped unexpectedly. Please try again. With a Force Close button, pushing it brings me back to the Welcome screen with no change.
I've searched around all day reading through any information I can find on this phone, I believe my best chance would be restoring it in recovery mode via an sd card update. I have not had any luck finding an update.zip that will work with this phone. I thought this was the same phone as the Concord (Z768 I think), but using files for it has not helped me, only results in an error message.
Any advice, tips or a swift kick in the butt to get me going in the right direction would be greatly appreciated!

So I contacted customer service. ZTE quickly sent me to straight talk. The poor straight talk guy was even more clueless then I.
I'm at your mercy, I'll continue searching for a solution, if I manage to find anything I'll update this thread in case anyone else runs into this problem.

When all else fails
return it to walmart!
Thanks for those who took the time to read and consider.

Tuluka said:
I rooted this phone and used link2sd to move some apps and free up internal memory. I think I moved the dialer app to sd, and shortly after the phone crashed, and restarting it was stuck in a boot loop. I went into recovery mode and did a factory reset. After doing this, it would make it all the way to the Welcome to Z768G screen. It says "Touch the android to begin" and has two buttons at the bottom, Emergency Dial and Change Language. When I touch the android it seems to react to my touch, but nothing happens. If I push Emergency Dial, an error message pops up that says "The application Setup Wizard(process com.android.setupwizard) has stopped unexpectedly. Please try again. With a Force Close button, pushing it brings me back to the Welcome screen with no change.
I've searched around all day reading through any information I can find on this phone, I believe my best chance would be restoring it in recovery mode via an sd card update. I have not had any luck finding an update.zip that will work with this phone. I thought this was the same phone as the Concord (Z768 I think), but using files for it has not helped me, only results in an error message.
Any advice, tips or a swift kick in the butt to get me going in the right direction would be greatly appreciated!
Click to expand...
Click to collapse
Hi, can ask how you rooted this phone,as I have been searching and haven't found an answer that works yet.
Thanks.

duffnip said:
Hi, can ask how you rooted this phone,as I have been searching and haven't found an answer that works yet.
Thanks.
Click to expand...
Click to collapse
I have the Tracfone version of this phone. I used KangoROOT from my PC, which I wouldn't recommend. Kango claimed that the root was a success, yet rootchecker app said unsuccessful. Now I am in the exact same situation as Tuluka. The only option left is to find a update.zip file for THIS specific phone.. Don't get yourself stuck in this bootloop!

Related

[Q] Serious Photon Issues

I am a new Android convert and purchased the Photon 4G last week. I successfully rooted, though I have not unlocked the bootloader. I flashed the Photon Laser 1.1 ROM, and then the Alien 1.1 Rom and theme. After noticing that I had no 3G/4G, I decided to revert to stock and avoid the Alien 1.1 for now. I went into Clockworkmod and wiped the dalvik cache, which I think was my major mistake, then in android recovery mode I wiped the cache 3 times, and did a factory restore. From this point forward I can not boot the phone successfully. Once it comes up to the tap the android to begin screen, I receive multiple error messages requesting the calander, phone, and other apps be force closed. I am unable to get into the phone at all. Additionally, if I tap the android icon, I can see the icon flex indicating my tap, but nothing happens. I've spent the last 6 hours attempting to use RSD Lite to reflash the stock image, but I receive an error each time stating "Failed flashing process. Unable to retrieve initialization values from INI file. (0x7029); phone connected." I need some direction from anyone that can help. Thank you in advance.
WEC2011 said:
I am a new Android convert and purchased the Photon 4G last week. I successfully rooted, though I have not unlocked the bootloader. I flashed the Photon Laser 1.1 ROM, and then the Alien 1.1 Rom and theme. After noticing that I had no 3G/4G, I decided to revert to stock and avoid the Alien 1.1 for now. I went into Clockworkmod and wiped the dalvik cache, which I think was my major mistake, then in android recovery mode I wiped the cache 3 times, and did a factory restore. From this point forward I can not boot the phone successfully. Once it comes up to the tap the android to begin screen, I receive multiple error messages requesting the calander, phone, and other apps be force closed. I am unable to get into the phone at all. Additionally, if I tap the android icon, I can see the icon flex indicating my tap, but nothing happens. I've spent the last 6 hours attempting to use RSD Lite to reflash the stock image, but I receive an error each time stating "Failed flashing process. Unable to retrieve initialization values from INI file. (0x7029); phone connected." I need some direction from anyone that can help. Thank you in advance.
Click to expand...
Click to collapse
Hey, I just wanted to confirm that you used RSDlite to flash the Final SBF release...45.2.5? And that didn't work? I've had issues with RSDlite attempting flash and then fail on me too. In that case, my phone would turn on into the Moto-boot logo, and then get stuck. I took the battery out and put it back in and it seemed to get me back into the phone after booting. Maybe you can try to reflash the final 45.2.5 update again?? Try using the cmd terminal to reboot or push files onto the phone? Sorry I don't know too much..I'm still really new to android.
I have followed the exact steps from this page: (http://forum.xda-developers.com/showthread.php?p=16328237), but every time RSD Lite fails with the error message I listed in the original post. I have pulled the battery several times, but am unable to get past the "tap the Android" screen. Tapping it leads to no change at all. I have no access to CWM anymore, and can only access recovery from Android recovery now, which I have used to reboot a few times at this point. When I reboot, I am greeted with errors that include "The process com.android.phone has stopped unexpectedly. Please try again." and "The application Suggestions Poll Scheduler Service (process com.motorola..suggestions.scheduler) has stopped unexpectedly. Please try again." and "The application Calander Storage (process com.android.calendar has stopped unexpectedly. Please try again."
WEC2011 said:
I have followed the exact steps from this page: (http://forum.xda-developers.com/showthread.php?p=16328237), but every time RSD Lite fails with the error message I listed in the original post. I have pulled the battery several times, but am unable to get past the "tap the Android" screen. Tapping it leads to no change at all. I have no access to CWM anymore, and can only access recovery from Android recovery now, which I have used to reboot a few times at this point. When I reboot, I am greeted with errors that include "The process com.android.phone has stopped unexpectedly. Please try again." and "The application Suggestions Poll Scheduler Service (process com.motorola..suggestions.scheduler) has stopped unexpectedly. Please try again." and "The application Calander Storage (process com.android.calendar has stopped unexpectedly. Please try again."
Click to expand...
Click to collapse
I know it's somewhere in this forum, but if you brick your phone and render it useless, you can try and reflash the original SBF...not the update. Give it a shot. Just let the force closes go, but see if you can connect to your computer. Best of luck!
Thanks, but I think that's what I was doing. Maybe it was the update. Can anyone point me to the original sbf? Thanks again for the replies.
http://www.multiupload.com/FNZKNV0T3G
thats the link, u need to unzip and then mount it on RSDlite
Thank you so much. I will download now and run it. Let you know if it finally works. Thank you for the link and help.
So nothing under the sun worked at all. I ended up having to take the phone back to the retailer and received a new one. I am happy now because after two days I have a functioning phone. I still believe that my error was clearing the dalvik cache before the factory reset, but I wouldn't have done that had the Alien ROM, which I mostly liked, hadn't killed my non-wifi data reception, as in I had none. Thank you the those of you who took time out to read and post a reply to help me. I am very grateful.
Help
Hey guys:
Yesterday I made mega mistake, I've flashed CM7 but... I didn't notice that I had to unlock the bootloader, obviously didn't work , but now, the phone is stuck on "unable to boot 2 entering RSD mode" with the Moto logo, so I tough, I will flash it again with the official Sprint update and fix the whole thing, but RSD gets to 100% restarts the phone and then phone shows just garbage! just like a blurry image, can't describe correctly but doesn't go any further. I've removed the battery start the phone again and then I get the same message "unable to boot 2 entering RSD mode". I'm on a loop right now, any advise will very appreciated, thanks'
Try flashing the 154_5 sbf...when in rsd mode...ive always had luck,with it as a starting point.
Sent from my MB855 using xda premium
KTT16 said:
Try flashing the 154_5 sbf...when in rsd mode...ive always had luck,with it as a starting point.
I will certainly give it a shot. I don't remember right now which file is the one that i got, I'm at work, but took me about 2 days in a row to download the file on my 128 kbps connection... third world connection.. I know.
Something that I would like to know is, when I turn the phone on takes directly to the error, if I press power + volume up then takes me to fast boot and stays there and if I do power + volume down gives a messages for about 1 second goes away and the phone goes like dead... I have to remove the battery to get it going again. Is there anything else that I need to know?.
thanks'
Click to expand...
Click to collapse
you need to get into rsd mode by powering up + volume up but use rsd verion 5.5 when connecting to the computer. Then after run the sbf and wait till it asks to manually power up the phone..pull battery and ur golden.
Make sure youre fully charged and have allege drivers installed properly.
Sent from my MB855 using xda premium
KTT16 said:
you need to get into rsd mode by powering up + volume up but use rsd verion 5.5 when connecting to the computer. Then after run the sbf and wait till it asks to manually power up the phone..pull battery and ur golden.
Make sure youre fully charged and have allege drivers installed properly.
You're the man!!!, I've dowloaded the file you told me and RSD 5.5 and I'm back in bussiness. I just unlocked the bootloader... ready to try CM7, yay!.
Thank you for your support, best regards.
Click to expand...
Click to collapse

[Q] trying to revert exhibit II to stock

hello xda. been browsing for a couple weeks, but finally registered today.
I have run into a problem I would like to try and solve without having to go through my insurance or carrier. my phone bricked itself after only 16 days, with 0 modifications on it. it was factory stock still. let me describe what happened, and what I did:
1st problem: I was using my online banking app (reputable bank), when the app minimized to the main screen; however, nothing OS related loaded. the phone just froze. only the wallpaper was visible. I tried powering it down, but it wasn't responding, so I pulled the battery, and put it back in. I powered on the phone, it loaded the SAMSUNG screen, then went to the Exhibit II 4G page, but then it stopped. it failed to load past the Exhibit II splash screen. no matter what I did, it stayed there. I googled for hours, trying various things, until I finally found this site with a stock rom setup.
2nd problem: I followed jocala's guide for flashing it, using Odin 4.43, and after it finished flashing, I got a "Firmware upgrade encountered an issue. Please select recovery mode in kies & try again." so now I have been googling this issue, and I cannot seem to find anything on how to fix it. I don't understand how my phone can just brick itself while using a banking app that i'd been using since I got the phone.
any help would be appreciated
also, if this isn't the forum for it, feel free to move it. this just looked the most appropriate seeing as there wasn't a board for the phone specifically.
deathbenotproud said:
hello xda. been browsing for a couple weeks, but finally registered today.
I have run into a problem I would like to try and solve without having to go through my insurance or carrier. my phone bricked itself after only 16 days, with 0 modifications on it. it was factory stock still. let me describe what happened, and what I did:
1st problem: I was using my online banking app (reputable bank), when the app minimized to the main screen; however, nothing OS related loaded. the phone just froze. only the wallpaper was visible. I tried powering it down, but it wasn't responding, so I pulled the battery, and put it back in. I powered on the phone, it loaded the SAMSUNG screen, then went to the Exhibit II 4G page, but then it stopped. it failed to load past the Exhibit II splash screen. no matter what I did, it stayed there. I googled for hours, trying various things, until I finally found this site with a stock rom setup.
2nd problem: I followed jocala's guide for flashing it, using Odin 4.43, and after it finished flashing, I got a "Firmware upgrade encountered an issue. Please select recovery mode in kies & try again." so now I have been googling this issue, and I cannot seem to find anything on how to fix it. I don't understand how my phone can just brick itself while using a banking app that i'd been using since I got the phone.
any help would be appreciated
also, if this isn't the forum for it, feel free to move it. this just looked the most appropriate seeing as there wasn't a board for the phone specifically.
Click to expand...
Click to collapse
Howdy, DBNP,
The Exhibit II is pretty much unbrickable...you won't need to resort to esoterica like jtag
The guide in the Exhibit II Wiki usually works out well. I'd try booting into stock recovery, doing a data wipe, then install stock with Odin. The Wiki has the links to the files you need. BTW, I didn't write the Odin portion @ the wiki; I just hosted required files when the links went stale.
Easy way to start recovery
* Pull the battery from your phone.
* Connect phone to your pc via usb.
* Press & hold Volume-up
* Insert battery
Once you're back up and running first thing you should do is install Clockworkmod. HTH, & good luck.
I cannot get my phone to get into recovery mode, though. if I press volume+up, the phone simply displays the firmware error message. thus, I cannot do a data wipe.
deathbenotproud said:
I cannot get my phone to get into recovery mode, though. if I press volume+up, the phone simply displays the firmware error message. thus, I cannot do a data wipe.
Click to expand...
Click to collapse
Sorry if this is redundant, but this was with:
Easy way to start recovery
* Pull the battery from your phone.
* Connect phone to your pc via usb.
* Press & hold Volume-up
* Insert battery
This has never failed for me. IDK, Perhaps your earlier Odin try wiped the recover partition. Can you get into Download mode? (hold Power-on Vol-Down)
I can enter download mode, but I cannot enter recovery mode. volume down gets me into download, while up gets me the error message. I cannot get to that menu anymore.
deathbenotproud said:
I can enter download mode, but I cannot enter recovery mode. volume down gets me into download, while up gets me the error message. I cannot get to that menu anymore.
Click to expand...
Click to collapse
Are you saying that you get an error when you press Vol-Up at the initial "Warning!" "A custom OS can cause..." screen, the initial download mode screen?
when I press and hold the vol-up sequence, it takes me to the initial error of "firmware upgrade has encountered an issue..."
when I press and hold the vol-up sequence, it takes me to the menu where it says custom OS etc., press up to continue, down to cancel (restart phone).
deathbenotproud said:
when I press and hold the vol-up sequence, it takes me to the menu where it says custom OS etc., press up to continue, down to cancel (restart phone).
Click to expand...
Click to collapse
And when you press Vol-Up at this screen what happens?
it takes me to odin mode/download mode.
deathbenotproud said:
it takes me to odin mode/download mode.
Click to expand...
Click to collapse
OK, that's good. That tells us that your exhibit2's /dev/block/mmcblk0p5 partition is undamaged. AFAIK Odin when properly used, can flash a new rom to your phone. Please try again, following the instructions in the wiki, reading carefully, downloading any files that you need, if you don't have them. Please walk through the wiki procedure to reflash stock from Odin, this procedure has worked for many,many people. Keep careful notes, you may be an edge case for some reason.
I'm posting links to this thread in the discussion threads that we use, since we're not allowed a forum. These threads get the most attention.
Exhibit II 4g discussion HERE
Exhibit II 4g dev thread HERE
yeah, I have tried doing that myself, as well as my friend who is rather skilled with android devices. he tried that all himself today, as well as attempting add. nothing worked.
deathbenotproud said:
yeah, I have tried doing that myself, as well as my friend who is rather skilled with android devices. he tried that all himself today, as well as attempting add. nothing worked.
Click to expand...
Click to collapse
I think you and your friend did it wrong. You should try again, following the wiki carefully.
we re-did it this morning step-by-step with no new results. we tried three times.
odin does its thing successfully, then when it goes to reboot, instead of going into recovery mod, it just goes to the firmware upgrade issue message.
deathbenotproud said:
we re-did it this morning step-by-step with no new results. we tried three times.
odin does its thing successfully, then when it goes to reboot, instead of going into recovery mod, it just goes to the firmware upgrade issue message.
Click to expand...
Click to collapse
Sorry to hear it. If Odin won't fix your phone and you've only had it a few weeks, I'd return it. I've linked your thread to our discussion threads, perhaps someone else has an idea.
that's the issue. because I have tried to flash it via odin, they're saying they won't take it because of the firmware upgrade error that keeps coming up. :/
because they won't take it, and the normal flashing to stock method isn't working, what do you think I should do next?
deathbenotproud said:
because they won't take it, and the normal flashing to stock method isn't working, what do you think I should do next?
Click to expand...
Click to collapse
I don't know who "they" are, but the chances of anyone at a T-Mob store or a Walmart knowing you touched your phone with Odin or even what Odin is are practically nil. "It's three weeks old, I turned it on and it doesn't work. Gimmie my replacement."
Or seek out a repair service to reflash your phone.
all right, i'll take it back and get a different rep. thanks for your help, though
deathbenotproud said:
all right, i'll take it back and get a different rep. thanks for your help, though
Click to expand...
Click to collapse
I'm sorry we didn't resolve the problem. Better luck next time!
deathbenotproud said:
hello xda. been browsing for a couple weeks, but finally registered today.
I have run into a problem I would like to try and solve without having to go through my insurance or carrier. my phone bricked itself after only 16 days, with 0 modifications on it. it was factory stock still. let me describe what happened, and what I did:
1st problem: I was using my online banking app (reputable bank), when the app minimized to the main screen; however, nothing OS related loaded. the phone just froze. only the wallpaper was visible. I tried powering it down, but it wasn't responding, so I pulled the battery, and put it back in. I powered on the phone, it loaded the SAMSUNG screen, then went to the Exhibit II 4G page, but then it stopped. it failed to load past the Exhibit II splash screen. no matter what I did, it stayed there. I googled for hours, trying various things, until I finally found this site with a stock rom setup.
2nd problem: I followed jocala's guide for flashing it, using Odin 4.43, and after it finished flashing, I got a "Firmware upgrade encountered an issue. Please select recovery mode in kies & try again." so now I have been googling this issue, and I cannot seem to find anything on how to fix it. I don't understand how my phone can just brick itself while using a banking app that i'd been using since I got the phone.
any help would be appreciated
also, if this isn't the forum for it, feel free to move it. this just looked the most appropriate seeing as there wasn't a board for the phone specifically.
Click to expand...
Click to collapse
go into recovery and do a factory reset then reboot from recovery.

Stuck at "Touch Android to Begin"

Alright Folks,
I have exhausted my search skills and probably messed up somewhere...Could use some guidance.
Background: I was updating a Slimrom and something went wrong on my end and I got stuck at Samsung boot screen. (Coulldn't get into recovery at all) I got to this thread http://forum.xda-developers.com/showthread.php?t=1457458 and followed the guide using ODIN and everything. Phone boots up but the back and search keys weren't working. Was able to make and receive calls but both parties couldn't hear each other. At this point I thought I should try rooting and get into recovery. I tried rooting using various methods ( DooMLoRD's Easy Rooting Toolkit [v4.0](zergRush Exploit), [1-Click Root][Video Tutorial][No Odin required]) but they didn't work and I was unable to get into recovery again.
I was glad that something is working. Its not a paperweight, yet. So then I thought this is the software for 9100 I should try getting stock to i777's software.
So after that I followed Entropy's Return/Unbrick to Stock, Kernel + Rooted System Package with Modem using Odin3 One-Click Downloader (Windows). Works fine ODIN says PASS. Boots with At&t logo and gets to "Touch android to begin" but when i touch it nothing happens. Couple pop ups appear time after time. "The application google services framework (process com.google.process.gapps) has stopped unexpectedly. Please try again" Also about Synchronization and calender. I tried to search but can't seem to find anything Useful.
I can get into download mode only.
Any help would be appreciated.
singhsta said:
Alright Folks,
I have exhausted my search skills and probably messed up somewhere...Could use some guidance.
Background: I was updating a Slimrom and something went wrong on my end and I got stuck at Samsung boot screen. (Coulldn't get into recovery at all) I got to this thread http://forum.xda-developers.com/showthread.php?t=1457458 and followed the guide using ODIN and everything. Phone boots up but the back but the back and search keys aren't working and couldn't hear the caller. Was recieving calls ok. So after that I followed Entropy's Return/Unbrick to Stock, Kernel + Rooted System Package with Modem using Odin3 One-Click Downloader (Windows). Works fine ODIN says PASS. Boots with At&t logo and gets to "Touch android to begin" but when i touch it nothing happens. Couple pop ups appear time after time. "The application google services framework (process com.google.process.gapps) has stopped unexpectedly. Please try again" Also about Synchronization and calender. I tried to search but can't seem to find anything Useful.
I can get into download mode.
Any help would be appreciated.
Click to expand...
Click to collapse
I don't think you've actually searched, because it's been said s few times already that you have to boot into recovery and factory reset.
Sent from my Zanpakuto using Getsuga Tensho!
Thanks for the reply Nick. I did see that but thats the problem I am not able to get into recovery. The button combos are not working (Holding vol up, down and power until samsung screen comes on second time OR holding vol up, down and power and once screen comes on letting go of the power button)(from power down state, of course). I've tried multiple times. I did make a nandroid on my ext sd card before I flashed so if I could just get into clockwork recovery I would've tried restoring to that. I did read that there is an android recovery as well...I couldn't get into that either (I think).
Edit: I just tried it again and the Samsung screen comes on the second time but instead of going into recovery it goes to At&t boot screen and then to "touch android screen".
PS. I guess I should have stated clearly that I am unable to get into recovery for some reason. See, it was all making sense in my head when I writing the OP but I guess the point didn't get across. I wanted to be concise and precise. But I guess now the issue is more clear.
singhsta said:
Thanks for the reply Nick. I did see that but thats the problem I am not able to get into recovery. The button combos are not working (Holding vol up, down and power until samsung screen comes on second time OR holding vol up, down and power and once screen comes on letting go of the power button)(from power down state, of course). I've tried multiple times. I did make a nandroid on my ext sd card before I flashed so if I could just get into clockwork recovery I would've tried restoring to that. I did read that there is an android recovery as well...I couldn't get into that either (I think).
Edit: I just tried it again and the Samsung screen comes on the second time but instead of going into recovery it goes to At&t boot screen and then to "touch android screen".
PS. I guess I should have stated clearly that I am unable to get into recovery for some reason. See, it was all making sense in my head when I writing the OP but I guess the point didn't get across. I wanted to be concise and precise. But I guess now the issue is more clear.
Click to expand...
Click to collapse
The only thing I can think of at this point then is maybe trying to use adb
Sent from my Zanpakuto using Getsuga Tensho!
Check out my signature. You can unzip the portable adb on your pc and try the reboot_recovery file. This will only work if your machine can detect your phone and you have the right drivers.
Sent from my SGH-I777 using xda premium
Worked like a charm. Restored to stock with root. Flashed a kernel with cwm. Flashed new ROM (to update to latest Cwm). Restored last backup. This bad boy is up and running like new. Thanks to all you folks.
Sent from my S(in)GH - I777

[Q] Galaxy note 3 Please help

my issue is very simple, I bought a galaxy note 3 today and I didn't like all the pages of useless hubs, I downloaded a program called titanium backup, it required routing but i felt voiding the warangy was worth freeing up my phone and making it more usefull... Anyway.. I opend titanium backup and I scrolled all the way to the bottom of the list and deleted the first 5 useless sounding applications, I can't remember what they are called but if I had a screenshot of the list I could pick out exactly wich ones I deleted, my phone got glitchy and I was stuck inside apps, I couldn't exit to the main screen, I turned off my phone.
When i turned it back on i got this message "unfortunatly the process com.android.setupwizard has stopped working"
I turned off the phone again. Rebooted the phone. I got the message again "unfortunatly the process com.android.setupwizard has stopped working", I was able to get into the settings and do a soft reset, after the reset my phone is stuck on the Samsung logo and will not start up, can somone please help me out here
Mr2Mikey said:
my issue is very simple, I bought a galaxy note 3 today and I didn't like all the pages of useless hubs, I downloaded a program called titanium backup, it required routing but i felt voiding the warangy was worth freeing up my phone and making it more usefull... Anyway.. I opend titanium backup and I scrolled all the way to the bottom of the list and deleted the first 5 useless sounding applications, I can't remember what they are called but if I had a screenshot of the list I could pick out exactly wich ones I deleted, my phone got glitchy and I was stuck inside apps, I couldn't exit to the main screen, I turned off my phone.
When i turned it back on i got this message "unfortunatly the process com.android.setupwizard has stopped working"
I turned off the phone again. Rebooted the phone. I got the message again "unfortunatly the process com.android.setupwizard has stopped working", I was able to get into the settings and do a soft reset, after the reset my phone is stuck on the Samsung logo and will not start up, can somone please help me out here
Click to expand...
Click to collapse
I know your new, but try not to double post things man.. Look over in the other thread you posted in and i asked you a few ?'s:good:
ya i did it unintentionally, i figured less people would be in the newbie section and i really need help i figures starting an actual thread and posting in an open thread would get more atention, wont happen again, should i delete this one?
Mr2Mikey said:
ya i did it unintentionally, i figured less people would be in the newbie section and i really need help i figures starting an actual thread and posting in an open thread would get more atention, wont happen again, should i delete this one?
Click to expand...
Click to collapse
No, it's fine just choose which thread you want a response in.. I responded in the newbie thread so lets keep it there..:good:
Mr2Mikey said:
When i turned it back on i got this message "unfortunatly the process com.android.setupwizard has stopped working"
I turned off the phone again. Rebooted the phone. I got the message again "unfortunatly the process com.android.setupwizard has stopped working", I was able to get into the settings and do a soft reset, after the reset my phone is stuck on the Samsung logo and will not start up, can somone please help me out here
Click to expand...
Click to collapse
If you've created a nandroid backup, restore it now. Otherwise you will have to flash another ROM in the recovery mode.

ZTE Valet Z665C "Stopped Responding" Errors and Can't Factory Reset

I have a horrible ZTE Valet Z665C (Tracfone), which is stock and running Jelly Bean 4.1.1. This is my first dumb, "smart phone" that I have owned, but I have owned a few computers so I should be able to understand anything you want me to try.
I can no longer use the cell because every 2-3 seconds another error message(ex. Unfortunately, the process android.process.acore has stopped; OneDrive has stopped; YouTube has stopped etc.) pops up and I can't clear them fast enough to do anything. If I try to uninstall an app that I installed, I get another stop error message, and nothing uninstalls. I tried Safe Mode, but the same thing happens. I have successfully done a factory reset via Recovery in the past, but now, even though it goes through the motions successfully, it doesn't actually factory reset anymore and remove any app I installed, and I still get tons of stop messages.
Is there a way to find a factory "update.zip" for my cell, so I can try to reset it that way? Can I attach the usb cable to my laptop, and somehow uninstall the apps I installed, just in case one is corrupted and causing these problems? If you have any ideas, I'm game to try them.
Thanks in advance.
...Stumped?
Seven days have gone by, and not one reply other then mine, here lol. If my post would get more traffic from experts elsewhere, I hope an admin or moderator can advise me. Thanks in advance.
This is a "Developers" forum, yet not one expert can take the time out of her/his day to offer up any suggestions?
Mods, is this in the wrong sub-forum, and if so, can you move it to the correct spot? I first asked for help in May of 2017 and there still has not been anyone able to suggest anything that may help at all. Thanks in advance.

Categories

Resources