Hi,
First of all, excuse some error typing. My english is better reading than writing!
To go direct to the point, I, by mistake, erased BMM via app. Then I did a reboot and the problem occur.
The thing is: On this phone, I haven't BMM or Safestrap to do the kexec thing to load the ROM. I think with fastboot command and the right file I was able to resolve the problem. BUT, the phone in Windows is recognized as UNKNOWN DEVICE, and even on other pcs with Windows (which I installed the moto drivers to test too, either in x86 or x64) it still is not recognized. In Linux world I'm new (using Sabayon). I installed the fastboot and adb (its working), but I don't know how to install the proper driver for the razr to try in.
Today I found this thread http://forum.xda-developers.com/showthread.php?t=2047750 and after reading it and searching, I found this too: http://forum.xda-developers.com/showthread.php?t=2055839. I think this case is possible my situation too.
I just want a way to restore this phone. Preferably, if possible, just installing again the BMM in some way, or, at least, take it recognizable in windows to flash in RSD.
Did you solve your problem? Long time since I've been here, last time.
No! Since I was expecting to the support of the people here...
I being busy these days and don't have time to try to figure out how to solve this problem.
Thanks for your concern.
Related
Have a Sprint TP2. Had Android running off my SD card last year and ready to try it again. My main computer is Win 7 64-bit, but I have access to other computers with Win 7 32-bit, and possibly another with XP if it is necessary.
-----------8<------------------
A few questions, if you please.
-----------8<------------------
I) To get a *complete* backup of my phone, I can use SPB Backup, right? (Will allow me to get *everything* back the way it is right now?)
II) Recommended Android ROMs are OMGB and GBX0*?
III) For OMBG:
.....1) I need to have ADB working (I installed it last night)
.....2) The readme said I needed to "have all the drivers installed". I don't know what that means.
.....3) The "How-To" also said I "must have Fastboot working".
.......a) Where do I get this? From here?
.......b) Is it difficult to install and/or run?
.......c) Found this, but no idea what it means
IV) For GBX0*, I need to download and install ClockworkMod Recovery. Where do I get this? From here?
You'll need the same things for Android NAND. They both require fastboot, and some sort of recovery. I prefer CWM.
Edit - Your links are pretty much all wrong. You should be getting pretty much everything from here.
Use whatever ROM you desire. Fastboot and CWM are agnostic to ROM.
For any NAND ROM to work, you need adb working. If adb works, fastboot *should* work.
Fastboot flashes from the NBH. If you flash the NBH for Android, you have fastboot (installed on the phone...)
It is a little difficult/tricky. Not for the feint of heart. Read a lot, test a lot, before you flash anything. Make sure you know the process and what you need to do.
Most importantly perhaps is a fully charged battery. I've seen a few users get stuck in fastboot mode because they let their battery die - and now without CWM or WinMo, the phone won't charge. Don't want to be in that situation.
If battery life is most important to you then OMGB is the way to go. If you need native tethering then GBX is the way to go. I use GBX as my daily. Either way read the threads, and you can see the features that work on either.
I am trying to get my Rhod 250 prepped. I have the flash program to unlock the Hard-SPL but the phone will not connect via USB and I am fairly certain attempting a flash over Bluetooth would brick the phone. I have tried disabling Advanced Network Functionality and have also tried installing the .cab file found in another thread but neither have made a difference. I am running Windows 7 64-bit Ultimate, and the Rhod is showing up as Unknown USB Device.
bigspoondude said:
I am trying to get my Rhod 250 prepped. I have the flash program to unlock the Hard-SPL but the phone will not connect via USB and I am fairly certain attempting a flash over Bluetooth would brick the phone. I have tried disabling Advanced Network Functionality and have also tried installing the .cab file found in another thread but neither have made a difference. I am running Windows 7 64-bit Ultimate, and the Rhod is showing up as Unknown USB Device.
Click to expand...
Click to collapse
Please make sure ADB works before you flash anything.
You need to do the unlock before you can flash any unsigned images regardless. HSPL is the first thing before flashing anything - custom WinMo ROM or Android.
Hi guys,
Wondering if anyone here has the know how to help.
Im fiddling with some new Kobo arcs, the 7HD and the 10HD and im having some bother with installing a custom recovery img.
For simplicity sake im going to refer to them as the same device as they are both behaving the same way
The device is rooted, and I am able to flash a custom recovery made by Jenkins builder but its not functional, when you boot to the recovery OS it just goes black and the back light flashes on an off (screen remains black it just lightens up)
At this point I can reboot as normal and adb to it and flash the original recovery img and all is well.
As far as I can tell its bootloader is unlocked but there might be a second bootloader im not able to interact with yet, possible called uboot?
From adb I am able to reboot the device in to bootloader and fastboot and both function as id expect, but the problem im having is booting directly to fastboot in case I bugger something up which would allow me to fix it.
I can boot the device in to a "mode" that tries to install an APX device, ive tried using various adb, fastboot, and composite drivers and nothing seems to work, ive downloaded some old NVidia APX tegra 2 drivers ive found but these fail to work with the NVFlash utility that comes with it, it says unknown device found, which would make sense given the utility is at least 3 years old
So firstly,
Does anyone know what might course the customer recovery rom to fail and yet flash like it is doing, if so any suggestions where to start to look for a solution?
Secondly,
Does anyone know much about this APX mode and how to actually put it to good use the driver appears to work and communicate but im needing something desktop wise to talk to it...?
hope you guys can help
edit
ive answered some of question 2 myself, it appears its a pain in the arse by all accounts and not as user friendly as I was hoping, I can send commands to it but it appears that commands may need to be "signed" of sorts as I don't get any response other than acknowledgment of the command sent, ill monitor the USB traffic and see if that sheds some light, it also appears that NVflash (not to be confused with its cousin in the GPU arena) is also hopelessly out of date and once again Linux is needed to get something more updated, if there is ANY help at all id appreciate some input
D
dazza9075 said:
Hi guys,
Wondering if anyone here has the know how to help.
Im fiddling with some new Kobo arcs, the 7HD and the 10HD and im having some bother with installing a custom recovery img.
For simplicity sake im going to refer to them as the same device as they are both behaving the same way
The device is rooted, and I am able to flash a custom recovery made by Jenkins builder but its not functional, when you boot to the recovery OS it just goes black and the back light flashes on an off (screen remains black it just lightens up)
At this point I can reboot as normal and adb to it and flash the original recovery img and all is well.
As far as I can tell its bootloader is unlocked but there might be a second bootloader im not able to interact with yet, possible called uboot?
From adb I am able to reboot the device in to bootloader and fastboot and both function as id expect, but the problem im having is booting directly to fastboot in case I bugger something up which would allow me to fix it.
I can boot the device in to a "mode" that tries to install an APX device, ive tried using various adb, fastboot, and composite drivers and nothing seems to work, ive downloaded some old NVidia APX tegra 2 drivers ive found but these fail to work with the NVFlash utility that comes with it, it says unknown device found, which would make sense given the utility is at least 3 years old
So firstly,
Does anyone know what might course the customer recovery rom to fail and yet flash like it is doing, if so any suggestions where to start to look for a solution?
Secondly,
Does anyone know much about this APX mode and how to actually put it to good use the driver appears to work and communicate but im needing something desktop wise to talk to it...?
hope you guys can help
edit
ive answered some of question 2 myself, it appears its a pain in the arse by all accounts and not as user friendly as I was hoping, I can send commands to it but it appears that commands may need to be "signed" of sorts as I don't get any response other than acknowledgment of the command sent, ill monitor the USB traffic and see if that sheds some light, it also appears that NVflash (not to be confused with its cousin in the GPU arena) is also hopelessly out of date and once again Linux is needed to get something more updated, if there is ANY help at all id appreciate some input
D
Click to expand...
Click to collapse
I know this is old, but how did you flash the original recovery? I think I need to do this so that I can install the update ZIP for the Kobo 10. CWM is failing to install the file.
Hello,
First off, I've gone through the forums and I have looked up other posts and despite everything I cannot figure out how to get my nexus 7 tablet to be recognized by the computer (I tried and after two days of searching for answers I decided to make a post). I like to include this information so people don't assume that I post without browsing or haven't tried anything yet.
The thing that I am having troubles with is that I have a nexus 7 tablet that is softbricked, I have already gone through a lot of ways to fix that problem (I found the best solution is this:http://forum.xda-developers.com/showthread.php?t=1809195). However, the issue is is that I cannot get my computer to recognize the nexus tablet to flash it and restore it back to factory settings.
I have installed and updated the device drivers on my computer, but still I have had no such luck. I found that ADB doesn't recognize the device whilst in the Bootloader, but still will not recognize the device in recovery mode. If anyone has any tips, or suggestions that might work PLEASE let me know, at this point I'm getting desperate and any/all help would be greatly appreciated!
Thank you!
NecroGi said:
Hello,
First off, I've gone through the forums and I have looked up other posts and despite everything I cannot figure out how to get my nexus 7 tablet to be recognized by the computer (I tried and after two days of searching for answers I decided to make a post). I like to include this information so people don't assume that I post without browsing or haven't tried anything yet.
The thing that I am having troubles with is that I have a nexus 7 tablet that is softbricked, I have already gone through a lot of ways to fix that problem (I found the best solution is this:http://forum.xda-developers.com/showthread.php?t=1809195). However, the issue is is that I cannot get my computer to recognize the nexus tablet to flash it and restore it back to factory settings.
I have installed and updated the device drivers on my computer, but still I have had no such luck. I found that ADB doesn't recognize the device whilst in the Bootloader, but still will not recognize the device in recovery mode. If anyone has any tips, or suggestions that might work PLEASE let me know, at this point I'm getting desperate and any/all help would be greatly appreciated!
Thank you!
Click to expand...
Click to collapse
adb is not designed to be usable in bootloader mode. You need fastboot for that. If you have the fastboot.exe program in the same folder as your adb stuff, try this:
fastboot devices
If it reads, then all you need to do is fastboot flash the various .img files back to the tablet. There are tool kits that do this for you, but I prefer doing it manually as there are less chances of things messing up and if they do, you're more likely to know at what step which could be useful for further troubleshooting if need be. It is important to download the correct img files due to differences between the generations and wifi / data enabled ones. There is a flash-all script that you can find in the download of the factory images, which might make it easier, but you can just manually flash the separate files as sometimes you don't need to bother with them all (like the bootloader) though if the script works, then it'll be fine and might make it easier if you are not familiar with the commands.
If you don't have fastboot at all, just grab it from here: http://forum.xda-developers.com/showthread.php?t=2317790
Nexus img files: https://developers.google.com/android/nexus/images
Hit me up on Hangouts if you need more direction.
NecroGi said:
Hello,
First off, I've gone through the forums and I have looked up other posts and despite everything I cannot figure out how to get my nexus 7 tablet to be recognized by the computer (I tried and after two days of searching for answers I decided to make a post). I like to include this information so people don't assume that I post without browsing or haven't tried anything yet.
The thing that I am having troubles with is that I have a nexus 7 tablet that is softbricked, I have already gone through a lot of ways to fix that problem (I found the best solution is this:http://forum.xda-developers.com/showthread.php?t=1809195). However, the issue is is that I cannot get my computer to recognize the nexus tablet to flash it and restore it back to factory settings.
I have installed and updated the device drivers on my computer, but still I have had no such luck. I found that ADB doesn't recognize the device whilst in the Bootloader, but still will not recognize the device in recovery mode. If anyone has any tips, or suggestions that might work PLEASE let me know, at this point I'm getting desperate and any/all help would be greatly appreciated!
Thank you!
Click to expand...
Click to collapse
You won't get adb in bootloader mode.
You have to use the fastboot command.
Please tell the OS on your computer.
Use the tool in my signature as an environment.
Download 7zip, and install that.
Then go here and download the proper image for your device.
It would either be "Factory Images "nakasi" for Nexus 7 (Wi-Fi)" or "Factory Images "nakasig" for Nexus 7 (Mobile)".
Grab the 4.4.2 version.
Extract the downloaded file with 7zip into the "Work" folder in the tool form my signature.
Then extract that "nakasig-kot49h-factory-83d93b5f.tar" file with 7zip.
Then go into the folder that came out of that, and extract the "image-nakasig-kot49h.zip" into the Work folder.
And enter the following commands while in bootloader.
Code:
fastboot oem unlock
fastboot erase userdata
fastboot erase system
fastboot erase recovery
fastboot erase cache
cd nakasig-kot49h
fastboot flash boot boot.img
fastboot flash recovery recovery.img
fastboot flash system system.img
fastboot reboot
Make SURE you grab the correct image for your device. Wifi or Mobile.
I also assume that you know the .img files should be in the Work folder before you type thse commands into my tool.
Hey guys, first of all thank you for the speedy replies and steps I should follow.
Right now I'm using OSX but for the tablet I'm using a virtual Win7 machine to try and get this damn tablet to be recognized by the computer. The process is being delayed a little bit because my micro USB cords are being temperamental, meaning that the tablet has no juice, and when I mess with it (using the power + volume buttons to boot to bootloader/recover) the cord comes unplugged. I know automatically you guys are going to pinpoint this as the source of the issue (mainly because I would too), but it works fine if just laid flat and stays connected. It just has zero charge so when it disconnects/reconnects I literally have to power it back up, just need to wait for it to have some charge before I tinker with it more.
I will post updates after it charges.
Although I already thanked you guys, thanks again for speedy reply. It's much appreciated.
NecroGi said:
Hey guys, first of all thank you for the speedy replies and steps I should follow.
Right now I'm using OSX but for the tablet I'm using a virtual Win7 machine to try and get this damn tablet to be recognized by the computer. The process is being delayed a little bit because my micro USB cords are being temperamental, meaning that the tablet has no juice, and when I mess with it (using the power + volume buttons to boot to bootloader/recover) the cord comes unplugged. I know automatically you guys are going to pinpoint this as the source of the issue (mainly because I would too), but it works fine if just laid flat and stays connected. It just has zero charge so when it disconnects/reconnects I literally have to power it back up, just need to wait for it to have some charge before I tinker with it more.
I will post updates after it charges.
Although I already thanked you guys, thanks again for speedy reply. It's much appreciated.
Click to expand...
Click to collapse
I suggest to STOP!!!
If you are trying to restore the device and the cable disconnects in the middle of it, it might not be recoverable. That would be one of the few ways to really damage the tablet as they are pretty difficult to hard brick. Don't half ass it with stuff like this. A good cable is not THAT much and will certainly be cheaper than a new tablet or getting it to a point where you might have to send it somewhere for service.
I'm not familiar with Macs, but if you are more so, then this might be better than using a Virtual set up:
https://code.google.com/p/adb-fastboot-install/
es0tericcha0s said:
I suggest to STOP!!!
If you are trying to restore the device and the cable disconnects in the middle of it, it might not be recoverable. That would be one of the few ways to really damage the tablet as they are pretty difficult to hard brick. Don't half ass it with stuff like this. A good cable is not THAT much and will certainly be cheaper than a new tablet or getting it to a point where you might have to send it somewhere for service.
I'm not familiar with Macs, but if you are more so, then this might be better than using a Virtual set up:
Click to expand...
Click to collapse
It's actually working fine now (in the sense that the computer can now read it). The Virtual Machine also works just as good, but for some reason the toolkit I'm using won't properly return the tablet to the stock image using the SkipSoft Android ToolKit, so I'm going to have to try and find another way.
Thanks for your guys' help.
Plz pardon my rant but I need major helpppppppppp lol, I've spent days scouring this site & google to try to fix this myself. I've built pc's but delayed learning droid because it's worse then mickersoft from what I've seen. I babysit for a lady raising her 3 granddaughters, they don't have net & were only able to access a few things. Sooo I volunteered to add some games, I was so flabbergasted at the bloat, shear greed and limitations of both versions of dis ui. I wanted to just disable it to use a different launcher but nooo to easy. no good deed goes unpunished lol. I updated the stock to the current as of two weeks ago ota kitkat and it went down hill fast, the dis ui worked for the most part but it wouldn't let me in the settings that's on the nabi mode for no apparent reason.
So not being able to find much current info for dis version, I made the huge mistake of using kingroots apk. it chocked but then work fine except I still had the above problem. no matter what I tried to clean or debloat. I got stupid tired and did a factory reset it now won't boot fully. I only get a pop up loop even in safe mode of nabiSetup has stopped. I can only turn off but can access recovery and the fastboot etc! I give it wins this round lol.
I have tried both win 10 32 & 64bit I only got it to connect once, it said I unlocked the bootloader but nothing can find the device to reboot-bootloader thru adb or NabiLab, 15 sec abd and etc. I'm to tired to think straight and to new to this so I must be missing something. there has to be away to get droid back on it! I can usually access the tablet and the sd card thru win explorer but no matter witch drivers I've tried it will not connect properly or the drivers won't install fully even with drive sig disabled. so it has to be because of the bitmap error I found in recovery or because it won't fully boot to access the usb on the tablet??
cliff-notes
1. the devise will not fully boot I get a nabiSetup has stopped popup loop in normal & safe mode I can only shut it off.
2a I can still get in recovery I tried to flash it but I assume I was using the wrong file nothing would load, but noticed E: missing bitmap stage_empty & stage_fill it seems to be a common droid problem but no info to be found for this devise version.
2b In the device manager fastboot comes and goes or I see a USB device descriptor failed or set address I think it was and pdanet stalls. I'm gonna fdisk laptop again it's had way to many driver attempts to be sure that's some of problem not operator error or usb in a mood again.
3. being brain-dead tired & a droid newbieish. I can't get to the usb to play nice so I can't install twrp. I assume because of the usb drivers ie google and etc not showing up right in device mangr. no usb on nabi which I just remembered the developer options vanished, that's why I decide to reset since what I think is the reset pinhole didn't work?
p.s I can access win explorer most of the time. the common droid/disney folders are showing but I'm unclear what all is missing.. can someone please give me a laymens clue how to get the os back on it. I deleted the cache and etc to no avail. I pieced together other peeps info here but so far I'm special no one has my exact errors lol. my gut says it's fixable from what I have read it seems to makes a difference its a disney version I don't care what's on it as long as it works at this point any ideas or help is deeply appreciated. I'm running win 10 ent 64bit at the moment and it was stock disney version of NABI2-NV7A-US-D with 4.4.1 before bad update of kitkat ota.
Twink225 said:
Plz pardon my rant but I need major helpppppppppp lol, I've spent days scouring this site & google to try to fix this myself. I've built pc's but delayed learning droid because it's worse then mickersoft from what I've seen. I babysit for a lady raising her 3 granddaughters, they don't have net & were only able to access a few things. Sooo I volunteered to add some games, I was so flabbergasted at the bloat, shear greed and limitations of both versions of dis ui. I wanted to just disable it to use a different launcher but nooo to easy. no good deed goes unpunished lol. I updated the stock to the current as of two weeks ago ota kitkat and it went down hill fast, the dis ui worked for the most part but it wouldn't let me in the settings that's on the nabi mode for no apparent reason.
So not being able to find much current info for dis version, I made the huge mistake of using kingroots apk. it chocked but then work fine except I still had the above problem. no matter what I tried to clean or debloat. I got stupid tired and did a factory reset it now won't boot fully. I only get a pop up loop even in safe mode of nabiSetup has stopped. I can only turn off but can access recovery and the fastboot etc! I give it wins this round lol.
I have tried both win 10 32 & 64bit I only got it to connect once, it said I unlocked the bootloader but nothing can find the device to reboot-bootloader thru adb or NabiLab, 15 sec abd and etc. I'm to tired to think straight and to new to this so I must be missing something. there has to be away to get droid back on it! I can usually access the tablet and the sd card thru win explorer but no matter witch drivers I've tried it will not connect properly or the drivers won't install fully even with drive sig disabled. so it has to be because of the bitmap error I found in recovery or because it won't fully boot to access the usb on the tablet??
cliff-notes
1. the devise will not fully boot I get a nabiSetup has stopped popup loop in normal & safe mode I can only shut it off.
2a I can still get in recovery I tried to flash it but I assume I was using the wrong file nothing would load, but noticed E: missing bitmap stage_empty & stage_fill it seems to be a common droid problem but no info to be found for this devise version.
2b In the device manager fastboot comes and goes or I see a USB device descriptor failed or set address I think it was and pdanet stalls. I'm gonna fdisk laptop again it's had way to many driver attempts to be sure that's some of problem not operator error or usb in a mood again.
3. being brain-dead tired & a droid newbieish. I can't get to the usb to play nice so I can't install twrp. I assume because of the usb drivers ie google and etc not showing up right in device mangr. no usb on nabi which I just remembered the developer options vanished, that's why I decide to reset since what I think is the reset pinhole didn't work?
p.s I can access win explorer most of the time. the common droid/disney folders are showing but I'm unclear what all is missing.. can someone please give me a laymens clue how to get the os back on it. I deleted the cache and etc to no avail. I pieced together other peeps info here but so far I'm special no one has my exact errors lol. my gut says it's fixable from what I have read it seems to makes a difference its a disney version I don't care what's on it as long as it works at this point any ideas or help is deeply appreciated. I'm running win 10 ent 64bit at the moment and it was stock disney version of NABI2-NV7A-US-D with 4.4.1 before bad update of kitkat ota.
Click to expand...
Click to collapse
It's hard to understand all of that but it sounds like perhaps you deleted some bloat that you should have, you sound like having driver issues, and possibly wrong TWRP version. Need to clear that up and then reinstall the stock Disney ROM.
I'd start here it has all the tools/TWRP/ROM's you need.
http://forum.xda-developers.com/nabi-2/general/nabi-information-t3229119
So sorry hun, toshiba is driving me nuts and I'm having a bad add moment or three lol. I read about you retiring. so I tried hard not to bother you. now I'm really confused. I've read your nabi2 general info post and even ran across your youtube vids. the problem is I'm not familiar with adb. & the included NabiLabGUI drivers, win10 either fails to finish saying it was interrupted. or it just won't install the 32 bit drivers, I thought I as suppose to use.
The 64bit driver 3 out of 4 install but, I can not get the Google Inc, driver to install properly even with the inf file. (ie the android_winusb.inf ) it says the system can't find the file, it can install the older versions from NabiLabGUI or naked drivers. but doesn't show in add/remove and it still won't detect the tablet most of the time lol.
Pda also has conflicts with adb, I got the nablab disney option to detect it but still failed to install twrp saying it can't find devise and I noticed in device manager 2 driver problems that will not let me update manually or they go missing if I try to force windows to reinstall. (device descriptor request & set address failed)
I must be missing something big, I also tried the 15sec and minimal adb. I assume because the tablet won't fully boot up, windows doesn't know what to do with it. when I tried different cables. windows 10 enterprise won't play nice at all now. so I will format again to be safe but lost what to try next.
I guess my questions should be is there a work around or a full inf version of the newer drivers for NabiLabGUI2015 that might work with this demonic disney nabi2.
&
Is NabiLabGUI compatible with .net framework 4.6 advanced services? (I may have to downgrade o/s. on the nabhacks site is says .net 4.5 is a prerequisites.) I don't know much about the app but saw 4.6 comes preinstalled, I can't install 4.5 yet, I saw there has been compatibility issues. and it won't let you revert versions easily if at all.
I'm to tired of this tab to think straight anymore and so grateful any help I'm in way over my head here.
Update
I lost the battle but I won the war, now google & supersu are messing with me as usual but it boots so I win lol :victory::silly:
I'll try to get as straight tot he point as possible.
Been using my Mobile one touch pix 7 for a little over a year and always installed Ota updates. Well I rooted the tablet not too long ago, forgot which method I used, but was working fine.
an Ota update came through and totally forgot it was rooted, and tried to install it, at which point the whole tablet got bricked.
It ended up in recovery, and I selected due to failure, to format and wipe the data.
Anyhow, The unit will stay at the boot screen for a while then show command error and then show the recovery screen, my only options are:
reboot
update from sd card
update via adb
update via memory
reboot Bootloader
power off
Well I've tried updating by downloading system images via adb, they return a verification error.
I've tried using adb side load to try to install an Ota update file I found for it, returns a verification error.
I cannot get into download mode, fast boot mode I think does not work as windows reports 3 android devices, but the mobile update software cannot see anything, and fast boot gets stuck at waiting for devices.
I suspect the tablet is for lack of a better description totally bricked and just a paperweight.
I am at a loss of what to try from this point. I'm sure wiping the data after the failed update killed it completely but not sure.
Anyone have any guidance here? I've downloaded a few images from the web I found that say they are for this tablet model, but still getting verification error.
Is there any flashing software I can get that may be able to access the tablet or can I copy a file to the scared and have it try to run an update from there. I don't care if it is rooted or not, just want to get it usable again.
I can run Mac OS, windows 10, windows 7, windows xp, or even have no issue getting a linux version going, whatever will work best for this I can use it. windows 10 I was able to manually add the drivers but windows 7 is not letting me do it the same way. I can connect via adb sideload only, no other adb functions seem to work.
I'm not a total news when it comes to custom rooms, as I have done it with another tablet, and an android car radio, but those were pretty straight forward and bootable so never ran into a brick issue yet.
I have a feeling this is toast and I hope that is not the case.
If anyone here can help out, I would appreciate it.
Thanks again....
Need help here to. Been searching with no luck. Any my issue is.
Rooted kingroot, flashed twrp with flashify and now I'm stuck on twrp. Been searching for any custom stock rom. I forgot to unlock the bootloader but I did enable usb debugging (i didn't see any oem options).
Any k 28532Jonsunf of help would be greatly appreciated.
This sorta happen to me. I rooted pixi 7 with kingroot, and was able to delete a lot of bloatware. However, when I was using lucky patcher it pretty much messed up the play store. But it was fine. I could download stuff through the Internet. But sooner or later I needed to fix it. Tryed a lot of ways but it didn't help. So I factory reset the tabletand now im stuck at the Setup Wizard. It just won't let me let me through. I thought its was over, but then I get a message saying there is an update available. So I download it and installed it. But all I get at the end is error. So now I need to flash it with stock. I tried the img. too, but it doesnt show up in the recover menu. If you found a solution please tell me
Can anyoonneee help me find a good Custom Rom for the alcatel one touch pixi 7 (9006W)? Sucks that there's not much info for this device (probably cause the device sucks lol) I'm running on lollipop 5.0.2 and am not able to get OTA update due to rooting. Unrooting didn't help. It seems only answer is custom rom but don't want to risk bricking it as I don't have a computer at home. Also, I am new to this so if anyone can share some insight, I'd be eternally grateful
P.s
It's a t mobile device but I only use it on wifi.
Am using kingroot.
Have never installed a custom rom
****ing device is 8 gigs. 1 gig Ram.
Is it possible to get Nougat?
Help meeee lol