Security problem error message - Android Q&A, Help & Troubleshooting

I got a Lenovo S939 few days back which I tried to upgrade from the phone update centre.It did not happen but the android screen started showing error message 'Security Problem' at left lower corner.It stays there all the time even after factory reset.It does not cause problem in phone operation but stays back as watermark ever.This irritate me a lot.I tried to flash my phone,but that is also not happening.Can any expert help me.It will be very kind.

Question.. did you ever figure out what was the cause of that message??

Related

Problem: com.google.process.app

Hi
I used Hero only one day, and device is death. I had problem with screen (was flashing) and now i can't use my phone. After start I see in polish "Process com.google.gapps is stoped. Try again." I can't do anything, phone restarts and always shows same statement. What can i do? Is any restart to factory settings?

[Q] OTA Update 651.167.26.en.EU

Anyone had a problem updating to 651.167.26.en.EU??
I've tried to update (many times), the phone shuts down starts the install, gets about half way then reboots. When it does reboot I get a message saying the update failed. I've even done a factory reset (which I hated) but now joy. Grrrrr
Has anyone had this issue and have you manage to solve it??
Also does anyone know what location the phone saves the update to?
Perhaps you're lucky it failed because I am having the following problem after the update:
After updating wireless is stuck and won't either turn on or off.. in settingsmenu on the wlan activate button it just says "error" in the second line. on push it says "activating" for some time the drops back to error. So my question: Does anyone else have this an what can I do to correct this?
PS: Moto Support just says Factory reset but there is upfront no way I am doing this without having tried anything else..
You could always just root it and install a custom rom. My app will will root it in 1 click.
BreakDroid

[Q] System Process is NOT RESPONDING

Guys,
I have Manually upgraded my OS from 4.1.2 to 4.2.1. From the day I have upgraded it, I am getting a peculiar error msg "System Process is NOT RESPONDING - Force Close or Wait"
After this msg for some days, my Phone stop showing anything on the screen & then again I have to do the RE-Process of Upgradation.
Has anyone got this problem, if Yes then what is the solution for the same.
Cheers
Tahir

New System Update Error for Moto E 2

My phone shows the new update and it downloads and starts updating but when it gets to a certain point it stops and says "Error" and reboots. I don't know what is going on. I got this phone second hand. It might have been rooted. Anyone know how to fix it???

Samsung A8 (2018), (SM-A530F/DS) homescreen stuck in "phone is starting" after update

Samsung A8 (2018), (SM-A530F/DS) homescreen stuck in "phone is starting" after update
Hi guys, yesterday i did a software update for my samsung A8 (2018) phone and it was going normal until i received an error message at the end of the update. My phone continued to boot successfully but now the homescreen is always stuck in "phone is starting" message.
The phone itself works and i am able to open other apps via google playstore but the homescreen is unusable. I have tried doing cache partition wipes and factory resets, i also thought it was a soft-brick so i tried FRP hijacker with the soft-brick fixer but it just says "check connection" even though my PC successfully scanned the port of my phone. When i open my phone in recovery mode it says "firmware is not valid" at the end of the command line.
I have tried searching online for similar issues but most users have experienced bootloops which is not exactly the problem i have right now.
Any help would be greatly appreciated, thanks
@Verthingale
Taken from Samsung:
Devices with Android 9 or higher will automatically enable file-based encryption if it has a PIN, pattern, or password set up. During the boot process, the phone will display "Phone is starting..." and the screen may be blank for a few seconds while encryption is taking place. However, if you feel it takes too long for your phone to start, you can disable the encryption to cut a few seconds off of the boot time.
Click to expand...
Click to collapse
jwoegerbauer said:
@Verthingale
Hi jwoegerbauer, thank you for the reply however unfortunately i don't think the "phone is starting" protocol is actually working. I only experienced this problem right after the latest software update and that was about last night, I have actually tried waiting for the phone to load up but it actually never does (even though i left my phone idle and waited for hours). I am fairly certain that it is a glitch/bug caused by the error at the end of the software update however i am not sure on what to do in such an occasion.
So as to clarify, the software update DID NOT complete as there was an error/failed message right at the end of it but while looking up in the internet i found out that apparently software updates are permanent and cannot be reverted back?
If that is the case then i am really in a pinch right now as i cannot go back to my old software version and yet the new one also does not work.
Click to expand...
Click to collapse

Categories

Resources