So when I was replacing the screen and the frame on my phone I realized the power button had a flex cable, one gentle movement and now it broke. I was able to order a new one but it's been 3 weeks since I had the phone taken apart and I don't remember how the flex cable attaches to the frame so that the button can actually touch it? If somebody could pop off their case and take a picture and/or undo their power button and describe how it goes back together that would be great!
gabessdsp said:
So when I was replacing the screen and the frame on my phone I realized the power button had a flex cable, one gentle movement and now it broke. I was able to order a new one but it's been 3 weeks since I had the phone taken apart and I don't remember how the flex cable attaches to the frame so that the button can actually touch it? If somebody could pop off their case and take a picture and/or undo their power button and describe how it goes back together that would be great!
Click to expand...
Click to collapse
In my experience, the power flex cable is soldered to the motherboard usually. You may have either buy a soldering iron and do the most precise work you've ever done in your life or contact a phone store. Sorry if this wasn't helpful.
Related
I just got this old phone from my friend after he upgraded. It's a solid phone but I'm having 2 issues.
1. The power button doesn't have the nice clicking feel to it. I opened the phone up and discovered the power button was one that I have not seen before. Is this button soldered onto the board? I would like to replace it myself, I have tried looking up power button fixes but was not able to find any results with this particular button type. It's usually the ribbon cable type deal with the flat disk contact kinda deal. Any idea where I can find some instructions and the buttons themselves?
2. I have a problem with the phone not powering down. After shutting the phone down the phone boots right back up or the screen shows the charging animation. Also the screen never goes into sleep mode it only goes into the dim mode. I looked up this problem and it seems to be a common one, a problem with the micro usb slot. I ordered the whole usb slot and the board its attached to. My question for this one is how difficult is the install?
Sent from my SGH-T989
I just replaced the screen one of my i777's. I followed this great guide my LE55ONS on YouTube. It was for I i9100, but they are almost the same phone. Along the way in the video he explains how to replace everything in the phone, including the microUSB board and flex cable, which if i remember was a pretty easy fix. As for the power button, i would try maybe putting a little piece of paper or cardboard or foam or something inside the phone right next to the button, that might make it more ferm when pushed.
Hope this helped.
Here's the link to the video :
tps://www.youtube.com/watch?v=65pvAINg2ME&feature=youtube_gdata_player
Sent from my SGH-I777 using xda premium
Thanks for the reply, yes I saw the video too, it was helpful but that dang power button is so mushy it feels horrible. A little update though I was able to fix the micro usb port by cleaning it with a brush then bending the pins towards the screen, it appears that over time the row of pins gets pushed too far down and shorts the assembly. Power problems fixed but not the power button. Only place I can find that even has the power button repair service is mobiletechvideos
Sent from my SGH-T989
You might want to check the forums for your device, as the hardware between the I777 and the T898 are very different.
http://forum.xda-developers.com/forumdisplay.php?f=1329
Title says it all really. I dropped it, but it had the keyboard attached and closed, it didn't fall far. However, now it won't turn on at all. If I hold down the power button, it will vibrate for half a second after I hold it down for about 10 seconds, but it doesn't turn on. Nothing appears on the screen.
It's completely stock, not even rooted. Does anyone have ideas?
The LCD screen ribbon cable has mostly come loose. This happen to mine when my son accidentally dropped my prime. Easiest way to confirm this is if you have a micro HDMI cable. Just plug the tablet into a TV and see if you have a picture. If you do then it is the LCD ribbon cable. The battery sits right under the screen ribbon cable and all it takes it a drop and a shift movement of the battery and the cable becomes unplugged. Just take the back cover off the tablet using the updated videos on XDA on how to disassemble the tablet. I used a little pick and two credit cards. The back cover comes off pretty easy and it is real easy to do - REALLY EASY. You will then see the ribbon cable above the battery. Just plug it back in better and secure it with tape. Power on the tablet if you want to check your work. If it works then reverse the steps taken to open up the tablet and you are done. While your in there you can tighten up the "screen" screws if you have screen light bleed too. Hope this helps you.
tdang said:
The LCD screen ribbon cable has mostly come loose. This happen to mine when my son accidentally dropped my prime. Easiest way to confirm this is if you have a micro HDMI cable. Just plug the tablet into a TV and see if you have a picture. If you do then it is the LCD ribbon cable. The battery sits right under the screen ribbon cable and all it takes it a drop and a shift movement of the battery and the cable becomes unplugged. Just take the back cover off the tablet using the updated videos on XDA on how to disassemble the tablet. I used a little pick and two credit cards. The back cover comes off pretty easy and it is real easy to do - REALLY EASY. You will then see the ribbon cable above the battery. Just plug it back in better and secure it with tape. Power on the tablet if you want to check your work. If it works then reverse the steps taken to open up the tablet and you are done. While your in there you can tighten up the "screen" screws if you have screen light bleed too. Hope this helps you.
Click to expand...
Click to collapse
I think you are right! I plugged in the HDMI cable and got a signal.
Now I'm going to try and take it apart. Wish me luck...You don't happen to have a link to the guide you spoke of do you?
Thanks!
http://forum.xda-developers.com/showthread.php?t=1479664
This is the link (How to is disassemble your prime) I used. Worked like a charm to open the tablet up without destroying it up or marring it. Also look at the posts of replacing the screen. You can see the LCD ribbon cable in the pictures. Hope this helps.
tdang said:
http://forum.xda-developers.com/showthread.php?t=1479664
This is the link (How to is disassemble your prime) I used. Worked like a charm to open the tablet up without destroying it up or marring it. Also look at the posts of replacing the screen. You can see the LCD ribbon cable in the pictures. Hope this helps.
Click to expand...
Click to collapse
while you are in there, if you have poor wifi you may want to do this http://forum.xda-developers.com/showpost.php?p=29685066&postcount=1085
It's fixed. Thanks again for the help!
Awesome, dude. Easy as pie thanks to the people on XDA .
Wow! Good going. Your a happy camper! Long live XDA....hoera
Sent from my MK16i using xda app-developers app
Okkay, so I have taken phones apart before and never had any trouble.. but theres always something that can go wrong.
My dumbass went to the beach with my Note 2, and got sand in the audio jack port, and i cleaned it out as good as i could and well i still couldnt listen with headphones. So i decided finally to take the back off and get a better look. There was indeed sand still in the audio port and i gently got it out.
but of course i accidently tore the power flex cable /button ribbon on my way of taking the phone apart. so, i ordered a replacement flex cable. replaced it, and yay the phone does not still power on. this is the type of cable that doesnt need soldering, its just a plug in/push type.
so, the phone does NOT power on at all..
the screen DEF does NOT have damage to it, .. considering everything was perfect before my dumbass decided to take the back off the phone.....nothing else is damaged i went to extremes to take the board off even to make sure, everything is fine!
so, other than the power cable/button, what could be causing the phone not to power on at all now?
The power button on a samsung note 2 that I inherited fails to work. The phone was left outside and rained on so when I first got it the screen did not work and I thought it was going to be trash however after drying it out and properly cleaning it the device screen works now and it will turn on when plugged in. I have one of the dongles that forces the phone into recovery but the power button just plain does not work. I don't know what to do but I would like to be able to use this phone.
I've dismantled a few of these phones and once I ruined a power button while sliding the the tool past it to pop the case apart. The power button is part of another assembly but can be replaced. Any version of the phone (Sprint/ATT/etc) will use the same subassembly for the power button. If that is the problem, you can swap it out.
Otherwise, you may have corrosion issues. I have brought older "dumb" phones back by spraying the circuit boards w/electrowash cleaner, scrubbing w/a toothbrush, and blowing off with an air compressor. Be sure to remove all ribbon connectors and scrub both sides of the connector. Also: DON'T JUST SPRAY THE PHONE WITH THE BACK OFF! the electrowash will stay visible the display, so do this in a controlled manner.
so my phone power button is sucks right now, and is very hard to press, i wonder if there is a way when my phone is dead, and by charging it will allow it to be turn on like an iphone! this helps alot, i dont care if i have to change anything as i am ready to take the risk if its possible!
The power button is easy to change and is very cheap. It's basically a flex cable and you cannot fix it. The copper switch is so thin that once you open it will break.
Here is a link where you can buy replacement flex
And you can find how to guide on youtube.
There was a trick to power on redmi note 2 with broken power button, maybe it works on RMN3 as well, but be careful with this method, you will have to reinsert the flex cable fast.
https://www.youtube.com/watch?v=U46rkLA1gDo
CeBits said:
The power button is easy to change and is very cheap. It's basically a flex cable and you cannot fix it. The copper switch is so thin that once you open it will break.
Here is a link where you can buy replacement flex
And you can find how to guide on youtube.
There was a trick to power on redmi note 2 with broken power button, maybe it works on RMN3 as well, but be careful with this method, you will have to reinsert the flex cable fast.
Click to expand...
Click to collapse
I see, is there anyway that I can just charge my phone to turn it on?