Zerolemon 9H Ultra Glass Armor: Tempered Glass Screen Protector
Unboxing:
I received a review unit from Zerolemon. The screen protector was sent in a bubble wrapped package. The packaging on the screen protector itself is thin poster board with plastic cut outs for the various pieces. It came with the screen protector itself, a small micro-fiber cloth and an alcohol wipe.
Installation:
Zerolemon has installation instructions printed on the poster board packaging. I didn’t need them, but for though who do, the instructions don’t make sense at all. Luckily the pictures convey much more than the written instructions do.
I applied the screen protector in my bath-room after I had the hot water running in the shower for about 10 minutes to minimize any dust particles that were in the air. I tried using the micro-fiber cloth to clean the screen of any residual oil and particles. It did a good job getting rid of oily residue, but is horrible at picking up dust, which might be due to the cloth being tiny (2”x2”). Then I used the alcohol wipe to wipe down the screen one more time. That did the trick. It removed the rest of the particles.
After taking a plastic film off the screen protector I placed it on my phone. The great thing about it is that you can move it slightly to get it to fit perfectly then tap the middle of the screen and the screen protector will adhere to the screen like magic! I didn’t have any issues with bubbles.
Initial Impressions:
The screen protector is much thicker than a plastic one. It somewhat hides the home button because the screen protector is thicker than the protruding button. Not really an issue with me because I actually prefer that so I don’t accidentally press the home button when the phone is in my pocket, but it might bother others. Powering on my device and testing the responsiveness of the screen, the first thing I noticed how nice it felt to touch. Feels just like the glass on the phone. With the rounded edges I wasn't able to feel where the screen protector started and ended from edge to edge of the phone.
The screen’s responsiveness was noticeably diminished. All gestures and taps had to be deliberate for the phone to register the touch. I use the S-Pen quite often to create illustrations on the device. For regular navigation using the S-Pen it operated like normal, but I noticed that I had to push harder while doodling on the screen or using the hand writing recognition. Due to the diminished responsiveness I did have to go into “Settings>Controls>Auto-adjust touch sensitivity” and enable that option so that the screen would return to normal.
Viewing angles are comparable to naked screen.
I will update again in about 2 weeks after I’ve had more time to put it through the torture test of life.
Any info on how thick it is, it looks exactly like the same as the MIME Feather Glass. I use the s-pen with the MIME and I didn't have to turn up the sensitivity but it's only .15mm thick.
airmaxx23 said:
Any info on how thick it is, it looks exactly like the same as the MIME Feather Glass. I use the s-pen with the MIME and I didn't have to turn up the sensitivity but it's only .15mm thick.
Click to expand...
Click to collapse
It's 0.3mm according to their website.
I hope to be receiving mine soon and will comment on the touch screen responsiveness as well. I currently use a 0.4mm thick glass screen protector (it started to bubble randomly, so I needed a new one anyways), and haven't noticed any reduction in responsiveness, so hopefully my experience will be able to provide a different experience than the OP (especially as I'm going from glass to glass, while it appears as though OP went from plastic to glass, which in my opinion is an incomparable difference).
I just received my review unit as well. It's very thin and barely noticeable. I'm using it with my ZeroLemon Extended Battery and it fits perfectly under the case. I haven't had screen responsiveness issues as mentioned in the OP.
I'll post pics up a little later.
Sent from my SM-G900V using Tapatalk
received mine zerolemon screen guard today also. Will ihave to pop off the build in screen protector on this zerolemon case I'm using, in order to use the tempered glass protector? thanks
dschoenike
dschoenike said:
received mine zerolemon screen guard today also. Will ihave to pop off the build in screen protector on this zerolemon case I'm using, in order to use the tempered glass protector? thanks
dschoenike
Click to expand...
Click to collapse
The screen protector wasn't built in on my case.
If yours has one built in, then you should probably remove it.
Sent from my SM-G900V using Tapatalk
I got my review unit today and its pretty good. Mouahmong's review is almost spot on. If you know how to apply a screen protector you are good to go. However, if you have never done it before, watch a Youtube video because the instructions shown on the inside of the package are terribly written.
My advice on applying (especially if your house/apartment or wherever you live is dusty) do it after a hot shower. Doing so will let the dust settle.
The screen protector does have somewhat rounded edges so it's not sharp unlike some other cheaper tempered glass screen protectors. However, with a 0.3mm thickness, you won't even be able tell.
I didnt have much of an issue with the home button after applying the screen protector. Some other brands will provide a stick on item to put on top of the home button so its easier to press, but with this screen protector being pretty thin (0.3mm) you wont need it IMO.
Other than that, so far so good. If I find any cons, I'll update this review.
haza12d said:
The screen protector wasn't built in on my case.
If yours has one built in, then you should probably remove it.
Sent from my SM-G900V using Tapatalk
Click to expand...
Click to collapse
thanks for the answer. I figured I would probably need to remove it. thanks again for responding.
dschoenike
Hey everyone I haven't received my test piece yet but I was wondering about the link zerolemon provided it doesn't take me anywhere to provide feedback or suggestions.
Sent from my SM-G900A using XDA Premium 4 mobile app
Here are some pics with the Tempered Glass Screen Protector paired with the ZeroLemon Extended Battery/Rugged Case. This thing is very thin. The previous glass screen protector I had installed was too thick and caused the top corners to lift up. No problem here. Fits like a glove.
Installed the zerolemon screen protector a few days ago and ABSOLUTELY LOVE IT with my 10,000 mah battery and rugged case! I never liked screen protectors because I thought they took away the OEM glass feel and clarity. I now admit my past reservations were completely wrong and I will never have my phone screens go naked again! The zerolemon glass screen protector fits like a glove with the 10,000 mah battery and rugged case and I would strongly recommend the protector to everyone who owns the rugged case to give this a shot. Last thing, the cost of this is better than most of the other name brand protectors out there.
How is it in sunlight? Does it glare a lot?
sd97cl said:
How is it in sunlight? Does it glare a lot?
Click to expand...
Click to collapse
Haven't tried it in sunlight but it should glare just as much as the regular glass.
This isn't a anti glare screen protector.
So far it does well in direct sunlight. Minimal glare. Similar to stock naked.
Sent from my SM-N900T using XDA Free mobile app
sd97cl said:
How is it in sunlight? Does it glare a lot?
Click to expand...
Click to collapse
It is the same as the OEM glass screen, no better and no worse. I think the glass protector feels smoother than the OEM screen. Maybe it's because the oleophobic coating was starting to wear off but I swear the new screen protector feels buttery smooth when I swipe my finger or use the s pen.
DarkManX4lf said:
I got my review unit today and its pretty good. Mouahmong's review is almost spot on. If you know how to apply a screen protector you are good to go. However, if you have never done it before, watch a Youtube video because the instructions shown on the inside of the package are terribly written.
My advice on applying (especially if your house/apartment or wherever you live is dusty) do it after a hot shower. Doing so will let the dust settle.
The screen protector does have somewhat rounded edges so it's not sharp unlike some other cheaper tempered glass screen protectors. However, with a 0.3mm thickness, you won't even be able tell.
I didnt have much of an issue with the home button after applying the screen protector. Some other brands will provide a stick on item to put on top of the home button so its easier to press, but with this screen protector being pretty thin (0.3mm) you wont need it IMO.
Other than that, so far so good. If I find any cons, I'll update this review.
Click to expand...
Click to collapse
So your saying to install it after a hot shower as in install the unit on your phone in the bathroom? Ive heard of the method before but didn't quite understand.
xbmoyx said:
So your saying to install it after a hot shower as in install the unit on your phone in the bathroom? Ive heard of the method before but didn't quite understand.
Click to expand...
Click to collapse
People recommend installing in the bathroom because steam from the hot water will prevent dust particles from floating in the air.
Sent from my SM-N900T using XDA Free mobile app
I love it so far. The packaging is nothing fancy but the product is top notch. I previously had the Nillkin tempered glass and this one is identical to it which is a good thing. All the cutouts are perfect. It feels just like the naked screen. The price is very much reasonable unlike those other brands selling them for $20+ and the quality is the same.
Sent from my Galaxy Note 3
I just received my review unit and will update this thread with my review in a few days. I did notice though after installing the screen protector there is a "bubble" in the top portion of the screen right overtop the notification panel and directly under the Samsung logo. I thought maybe I installed it wrong or slightly sideways so I very gently pulled it back up making sure I didn't touch the sticky backing and realigned the glass with the home button and pressed it back down firmly. The "bubble" is still present but a tad smaller then it was originally. I kept rubbing the screen hoping to eliminate the bubble like other brand plastic type screen protectors and no dice. I will give it a few days and hopefully it will work itself out. I hope I didn't somehow get a "defective" glass that wasn't completely flat which is causing this bubble. See attached pic showing the "bubble" and the packaging stating it has "Bubble Free Installation". [emoji53]
xbmoyx said:
I just received my review unit and will update this thread with my review in a few days. I did notice though after installing the screen protector there is a "bubble" in the top portion of the screen right overtop the notification panel and directly under the Samsung logo. I thought maybe I installed it wrong or slightly sideways so I very gently pulled it back up making sure I didn't touch the sticky backing and realigned the glass with the home button and pressed it back down firmly. The "bubble" is still present but a tad smaller then it was originally. I kept rubbing the screen hoping to eliminate the bubble like other brand plastic type screen protectors and no dice. I will give it a few days and hopefully it will work itself out. I hope I didn't somehow get a "defective" glass that wasn't completely flat which is causing this bubble. See attached pic showing the "bubble" and the packaging stating it has "Bubble Free Installation". [emoji53]
View attachment 2863973
View attachment 2863974
Click to expand...
Click to collapse
Mine went on smooth without any bubbles. Maybe you got a bad one?
Sent from my Galaxy Note S5
Related
Hey everyone,
looking for a great screen protector that helps with the glare issue and viewing angles. I'm not expecting wonders but anything to help. Hate the fact I see reflection on screen sometimes. Any info would be great. Thanks
Gemni69 said:
Hey everyone,
looking for a great screen protector that helps with the glare issue and viewing angles. I'm not expecting wonders but anything to help. Hate the fact I see reflection on screen sometimes. Any info would be great. Thanks
Click to expand...
Click to collapse
How about checking the Skinomi thread in this very first page of this section ?
I just orderded some screen protectors from ebay hong kong. 11.99 for 3. ill let you know how they work.
Good Screen Protector
Ordered one from Amazon made by Aurum(do a search). It came quickly and I am very happy with it, wished I waited a few days, they have a deal going on with it.
It says its made from Japanese PET, in my experience it is better than those "military" strength ones like Zagg etc(bad evo 4g experience). This one has a dry application and protected on both top and bottom by covers (a protector for the protector). Ships from the US.
I have the Skinomi. I'm happy with it, but it does not appear to help with glare or screen angles (though, honestly, I only used it for a few minutes before installing the protector).
dj_justice said:
I just orderded some screen protectors from ebay hong kong. 11.99 for 3. ill let you know how they work.
Click to expand...
Click to collapse
which ones did you get?
-J
Go with the Skinomi one. It's cheap (relatively if you consider lifetime free replacement) and if you don't botch the installation it looks fantastic. And... you don't have to wait three weeks for something to come from China.
Don't get me wrong, I buy stuff from China sometimes but only when I can't get it here or if it's a lot more money to get it from here.
Anyone have recommendations for screen protectors? Looking for helping with anti glare and no finger prints on it. Any info would be great. Thank for all the feedback so far.
Traderny said:
Ordered one from Amazon made by Aurum(do a search). It came quickly and I am very happy with it, wished I waited a few days, they have a deal going on with it.
It says its made from Japanese PET, in my experience it is better than those "military" strength ones like Zagg etc(bad evo 4g experience). This one has a dry application and protected on both top and bottom by covers (a protector for the protector). Ships from the US.
Click to expand...
Click to collapse
I just ordered one of the Aurums too. I have a "matte" type screen protector on my iphone and I really like it so I hope the aurum one is similar. I will update once it arrives.
emersonlp said:
I just ordered one of the Aurums too. I have a "matte" type screen protector on my iphone and I really like it so I hope the aurum one is similar. I will update once it arrives.
Click to expand...
Click to collapse
Do you mean this one ? according to the user image its not custom made (no holes for the camer/sensors) not sure if it would even cover the bezel + the screen.
sjmoreno said:
Go with the Skinomi one. It's cheap (relatively if you consider lifetime free replacement) and if you don't botch the installation it looks fantastic. And... you don't have to wait three weeks for something to come from China.
Don't get me wrong, I buy stuff from China sometimes but only when I can't get it here or if it's a lot more money to get it from here.
Click to expand...
Click to collapse
The Skinomi one requires a WET application, that then has to dry, do you really want to spray some liquid on your new g-tab? I tried this on my Evo installation was a pain but then my fingers got stuck scrolling, so I learned my lesson and stick to the PET material which has a silicone coating for smooth movement
Aurum Screen Protector
You are right, I have the Aurum one from Amazon on my G-tablet, and there are no holes, but I do not see a difference in camera performance. The protector covers bezel to bezel. I've used the camera with and without the protector, all I know is that it is as grainy before as it was after the Aurum screen protector. I do not use the camera(I really do not need anyone getting scared looking at me) so it's fine by me, it the smoothness of movement that matters.
just my $0.02, but why not use the one by Zagg....?..
http://www.zagg.com/invisibleshield...es-screen-protectors-covers-skins-shields.php
Traderny said:
You are right, I have the Aurum one from Amazon on my G-tablet, and there are no holes, but I do not see a difference in camera performance. The protector covers bezel to bezel. I've used the camera with and without the protector, all I know is that it is as grainy before as it was after the Aurum screen protector. I do not use the camera(I really do not need anyone getting scared looking at me) so it's fine by me, it the smoothness of movement that matters.
Click to expand...
Click to collapse
Thanks for the info, Traderny. Would you say that the Aurum screen protector allows for smoother gliding movements than the unprotected GTab screen? I'm hoping to find something that provides a nice swipe feel. Too often my fingers would "stick" to the naked screen or (less so, but still) the Skinomi protector.
My .2 cents
Traderny said:
The Skinomi one requires a WET application, that then has to dry, do you really want to spray some liquid on your new g-tab? I tried this on my Evo installation was a pain but then my fingers got stuck scrolling, so I learned my lesson and stick to the PET material which has a silicone coating for smooth movement
Click to expand...
Click to collapse
Wet application screen protectors have been around for a while and it has been shown to not be an issue if you follow the directions on installation. There are thousands of people that have used wet installation screen protectors here in the gTab forums that have reported no residual issues with the gTab during/after application.
Also, you don't spray liquid on the gTab, rather you're supposed to spray the liquid on both sides of the screen protector before application and dab up the excess liquid as you work it to the edges with the provided plastic card.
I've used both PET and this style of screen protectors on devices before and I prefer this over the PET as I have found the PET style protectors to be too shiny for my tastes.
Among the most helpful reviews for the PET protector on Amazon there are these comments:
1.) Good product, but a pain to put on. Just the slightest piece of dust will cause an air bubble.
2.) According to the packaging, this item is "Finger print free" and "Bubble free application". I experienced both. I would NEVER purchase this product again or recommend it.
Just goes to show you that people will find something to complain about no matter what the product is.
Protectors Protect
My experience with screen protectors on cell phones is that they are only good to protect the screen from damage. All of them will show fingerprints, smudges, grease and oil. This is esp. true with a touch screen. it's like wearing glasses you got to clean them alot. So save time money and headache by putting a microfiber cloth in the bag with your Gtab.
I went with the Exim anti-glare screen protectors, but did have to wait for shipping from China. I bought a complete skinomi skin set, and promptly botched the wet application of the screen protector, but since I wanted the anti-glare it just meant a week wait for the Chinese Air Mail which I had already ordered.
Overall I like the Exim, it was easy to install without any bubbles, though you might want to trim the corners a bit as its a very tight fit. I ended up cutting them off after applying it because I had the screen on perfectly without a single dust mote making a raised area. I don't mind a poorly cut corner, but do wish I had just done a quick trimming beforehand as I wasn't perfectly centered.
2 for $12.99... Was worth the wait.
Hey Naieve,
does it really help with the anti glare issue? Also does it have any issues with the touch screen interface? Is the screen protector to thick that it doesnt detect your finger movement on the screen? Any help on the finger print issues haha?
It helps some with the glare, definitely diffuses the light, but it looks more like a compromise in between a clear protector and some of the very heavy anti-glare screen protectors I've seen. I like it because of this actually. As to issues with the touch screen, I spent some time googling before buying, and while I forget where I read it the fact is there is no difference while using this protector. Even a light touch still works just fine. I wonder if that is the reason this AG protector diffuses less light, as I have heard of some AG protectors being too thick and screwing up touch. It does still show fingeprints, but its not that bad and is easy to clean. Definitely less noticeable than just the screen itself.
aasoror said:
Do you mean this one ? according to the user image its not custom made (no holes for the camer/sensors) not sure if it would even cover the bezel + the screen.
Click to expand...
Click to collapse
I said I would update once my Aurum arrived. Like others have mentioned, there is no cutout for the camera or sensor - I don't know what effect that has nor do I really care. I never use the camera anyway.
The protector itself fits perfectly on the screen - it is so perfect that I had trouble aligning it properly and i would get halfway done installing it and notice it was running off the side of the screen slightly.
It took a few minutes to install because I did want it to be perfect. Now that it is installed I am really happy with it. My fingers slide better across the screen and there are far less fingerprints. I am happy with my purchase.
So I received my TechMatte screen protector today. I installed it a few hours ago. I honestly didn't have high expectations for it. I had forgotten that I had a TechMatte screen protector coming, so installed my Ghost Armor screen protector when it came in on Saturday. When the TechMatte screen protector came today, I placed it over the screen just to get an idea of the coverage that it offered. I was impressed that it was truly edge to edge on top, bottom, and both sides! There literally is no room for error on install, which is a good thing in my opinion! Just use the hinge method to get it on there perfectly. Also, the Home button has a cutout for it specifically. Most screen protectors just have a U shaped cutout at the bottom, and they don't offer any coverage below the Home button. Even Ghost Armor for the Note 3 uses the U shaped cutout, where Ghost Armor for the Note 2 has a specific hole for the Home button. I expected the Home button cutout for the Note 3 to be the same as the Note 2, so I was disappointed to see that they slacked on the Note 3 Home button cutout. So earlier I peeled off my Ghost Armor screen protector and lined up the TechMatte screen protector to do the hinge method. TechMatte even includes 5 tape strips in the package that are labeled for using with the hinge method, very nice touch on there part! I used the included cloth to wipe my screen clean of any dust and/or fingerprints. The cloth they include is larger than any cloth I've received with any other brand screen protector too! So I layed the screen protector on the screen and pushed out any bubbles. There was surprisingly very few bubbles on the screen, and the ones that were there were very easy to push out. I get it on and it's lined up perfectly. After peeling off the last film from the top of the screen protector I get my first feel of the actual screen protector itself. I am truly amazed by how it feels! It feels just like the bare screen! Looks wise, unless you're really REALLY looking for it then you would never know there's a screen protector on it! An hour or so later I handed my phone to a couple friends an told them to check out my new screen protector. They didn't believe me at first! Lol. I had to point it out to them for them to believe me! They both said it feels just like glass and is perfectly clear and not even noticeable! Now I've been using touch screen phones for many MANY years, since the early Windows Mobile days. I've always had screen protectors on every phone I've owned. This screen protector is by FAR the very best I've ever used or seen! I've been a fan of Ghost Armor for quite some time, and always recommend them to everyone. Hard for me to believe, but that time has come to an end! TechMatte is hands down my new favorite! I'll be recommending them to all of my friends, and using them on all of my devices from now on! I took some pics with my Evo LTE, because it takes better photos than my Note 2. I'll post pics in the second post with it, so please no one comment until I get on my Evo LTE and put up some pics. It's hard to even see the TechMatte screen protector, but I'll try to get some closeups of the Home button and the top of the phone.
Here's the link (CRAZY LOW Price with a Lifetime Warranty!!) : http://www.amazon.com/gp/aw/d/B00FR...film note 3&qid=1382465346&ref_=sr_1_1&sr=8-1
I apologize for not having the link in the OP to begin with. Anyone considering a screen protector is crazy not to buy these!! This price is insanely cheap!! This isn't just for 1 screen protector either, you get 3 with this!! Better jump on this deal while they are on sale!! I'm not sure how long the sale will last, so you shouldn't wait long, if at all!
Sent from my White Sprint Note 3 via XDA Premium
Pics
Sent from my White Evo LTE using XDA Premium
More pics
Sent from my White Evo LTE using XDA Premium
It's only letting me attach 1 pic per post
Sent from my White Evo LTE using XDA Premium
Corner showing the gap, or lack thereof rather! Lol. This screen protector has incredible coverage!
Sent from my White Evo LTE using XDA Premium
Another
Sent from my White Evo LTE using XDA Premium
Sorry about the 1 pic per post. I'll just wait until tomorrow, use a digital camera to take pics, an use my laptop to post them. Bottom line though, if you want a screen protector, TechMatte is absolutely the BEST choice!! I'm going to remove every screen protector on my other devices and replace them with a TechMatte screen protector!! Give them a try, I guarantee you will not be disappointed!!
Sent from my White Sprint Note 3 via XDA Premium
Link to site selling them?
carlz28 said:
Link to site selling them?
Click to expand...
Click to collapse
Here is the link : http://www.amazon.com/gp/aw/d/B00FR...film note 3&qid=1382465346&ref_=sr_1_1&sr=8-1
This is an amazing deal!! 3 screen protectors for less than $5!!!!!
Sent from my White Sprint Note 3 via XDA Premium
Aren't these the amfilm screen protectors? I grabbed some when they had these for $.50 for a 3 pack the other day, just received mine in the mail but I don't yet have the phone to try them out. Not only did the shipping address say TechMatte, the screen protector itself looks just like the one in the OP.
If anyone's interested, you can get these at Amazon: http://www.amazon.com/gp/product/B00FRIK0TQ/
for $2.50/3-pack shipped with coupon code: NOTE350F
codes takes 50% off
Kawaisa said:
Aren't these the amfilm screen protectors? I grabbed some when they had these for $.50 for a 3 pack the other day, just received mine in the mail but I don't yet have the phone to try them out. Not only did the shipping address say TechMatte, the screen protector itself looks just like the one in the OP.
If anyone's interested, you can get these at Amazon: http://www.amazon.com/gp/product/B00FRIK0TQ/
for $2.50/3-pack shipped with coupon code: NOTE350F
codes takes 50% off
Click to expand...
Click to collapse
Cool thanks. Just picked up 2 packs. I have been using the SPIGEN protectors but twice now ordering from them the packages have been damaged and they refuse to replace them. Took it up with AMAZON customer service.
Hopefully these work well. Can't go wrong for the price.
Thanks OP for the review.
TechMatte screen protectors
I received my TechMatte screen protectors in the mail yesterday for my Note 3 and Nexus 7 2013. I had never heard of TechMatte or their products before so I wasn't really sure what to expect. Upon inspecting the packaging I became worried as the image of the SP showed that it did not have a cutout for the home button but rather an upside down U-shape that starts above the home button and leaves it open below. However upon opening the packaging and inspecting the screen protectors they do indeed have a cutout for the home button that fully surrounds it and thus provides coverage for the entire bottom region of the device.
Included in the package were 3 SPs, an anti-lint/dust microfiber cloth, a sheet of tape strips to perform the hinge method for install, a squegee card to remove bubbles, and installation instructions. Installation was very straightforward being that it is a dry install. The fitment is fantastic. Other than the speaker grill and sensors it FULLY covers the front of the device edge to edge with almost no gap. Clarity is excellent and so is the "feel". I have no sensitivity loss with my fingers nor with the S-Pen. I attempted to press on the protector fairly hard with the S-Pen and also tried to make indentions into the film with my finger nails and was unable to do so.
At the current asking price of $4.50 for the kit with 3 SPs on Amazon I would not hesitate to recommend these SPs to anyone and would probably say that these may be the best bang for your buck screen protectors you can get right now. :good:
ghostfaceg35 said:
I received my TechMatte screen protectors in the mail yesterday for my Note 3 and Nexus 7 2013. I had never heard of TechMatte or their products before so I wasn't really sure what to expect. Upon inspecting the packaging I became worried as the image of the SP showed that it did not have a cutout for the home button but rather an upside down U-shape that starts above the home button and leaves it open below. However upon opening the packaging and inspecting the screen protectors they do indeed have a cutout for the home button that fully surrounds it and thus provides coverage for the entire bottom region of the device.
Included in the package were 3 SPs, an anti-lint/dust microfiber cloth, a sheet of tape strips to perform the hinge method for install, a squegee card to remove bubbles, and installation instructions. Installation was very straightforward being that it is a dry install. The fitment is fantastic. Other than the speaker grill and sensors it FULLY covers the front of the device edge to edge with almost no gap. Clarity is excellent and so is the "feel". I have no sensitivity loss with my fingers nor with the S-Pen. I attempted to press on the protector fairly hard with the S-Pen and also tried to make indentions into the film with my finger nails and was unable to do so.
At the current asking price of $4.50 for the kit with 3 SPs on Amazon I would not hesitate to recommend these SPs to anyone and would probably say that these may be the best bang for your buck screen protectors you can get right now. :good:
Click to expand...
Click to collapse
Yea, I'd never heard of them before either, so I also wasn't expecting much. I must say though, I was pleasantly surprised! They also sent me a screen protector for my N7 FHD as well, as they saw in my sig that I had one. Have you installed yours yet? If you haven't yet, definitely use the hinge method! There is no room for error on install, as this screen protector really covers from every edge to edge!!
For those looking, definitely jump on that Amazon deal!! This morning I forgot that I even had a screen protector installed!! It truly is an incredible looking screen protector, because there is nothing to look at or see!!! Lol. I'm still in amazement over it! Like I said in the OP, I've been using screen protectors for a long time and this one is definitely the best!! There really isn't any competition to these!
The only negative, which is really a positive in my opinion, is that you must install it perfectly. I've said it before, but there really is no room for error as this screen protector covers everything!! You do get 3 in the package, so if you mess up on the first install you have 2 more tries. I got mine right on the first try, so as long as you're really careful then you can as well. I highly recommend using the hinge method though!! If you aren't sure what that is then watch some YouTube videos on how to do it and you'll be set!
Sent from my White Sprint Note 3 via XDA Premium
Yeah I installed them both last night. The Nexus 7s protector was more forgiving in it's fitment than the Note 3s IMO. The N3s SP was almost exact to the size of the screen inside the chrome bezel while the N7s left a little more room for play but since you gotta line up the camera and sensors into the small opening it made lining it up a little easier.
Link added to OP. I'll post it here also. 3 for less than $5!!!!
http://www.amazon.com/gp/aw/d/B00FR...film note 3&qid=1382465346&ref_=sr_1_1&sr=8-1
Sent from my White Sprint Note 3 via XDA Premium
So after a few days of use I'm just as happy as was the first day! Still looks perfect and swapping cases repeatedly hasn't bothered the edges of the screen protector! Still highly recommend these! You WILL be satisfied!!
SwiftKey'ed from my White Sprint Note 3 via XDA Premium
My Review
I have to agree with the OP. A great product with great screen coverage and feel. I received mine from techMatte a couple weeks ago:
Full Disclosure: TechMatte provided me a free sample to test
I am not normally a big fan of screen protectors for my phones. Mainly because it's just a hassle to put on and the screen just doesn't feel right as compared to the naked screen (and I can never get them lined up right).
CONTENTS: The pack I received had 3 screens along with a microfiber cloth, plastic card to squeeze out any bubbles, an installation manual, and hinge stickers (for installation).
INSTALLATION: Installation was very easy and it's a dry install. I'm a perfectionist (which is why I don't normally like putting on screen protectors) and the supplied stickers for the hinge method of installation (which was outlined in the installation manual) helped me actually get it lined up perfectly on my first try!
LOOK: Once installed it was perfectly clear. No discoloration that I could discern. There were three bubbles that I wasn't able to squeeze out immediately specifically because I missed really small pieces of lint. I was a little frustrated at first because I had thought I'd done well keeping it clean (note, I would have been better served installing in a more well lit room...I'm sure I missed them because I didn't have good lighting while installing)...but, they were really small so I figured I'd give it a little time.
I'm pleased, and surprised, to say that after a couple days those last few bubbles actually went away leaving a nice, clean, clear surface.
FEEL: As far as feel, a big question I had going into it was how would the screen feel under finger and, more importantly, under the stylus. I have a friend who has screen protector where it's very rubbery and every time he uses the stylus on his Note 2 there are grooves left behind. I can confidently say that this screen protector does not have that problem at all.
I also want to call out that the screen protector does not have an affect on the sensitivity of the screen either with your finger or with the stylus.
Under finger if I dig my nail in a bit, I can feel that it's a bit rubbery but just normal use it's smooth without any noticeable drag. It does feel slightly different from a naked screen, but it's still pleasant and not distracting at all (and I feel that I'm picky on feel).
As for the stylus, I was surprised again here. Right after it was installed there was a little bit of drag when I used the stylus but that quickly went away as I continued to use it. If your extremely picky (or if you have a heavy hand) you might notice a bit of a difference but I don't.
OVERALL: I'm absolutely sold on this screen protector and would recommend it to protect your screen. Installation was easy with the included supplies, the protector is very clear and, unless you know what you're looking for, unnoticeable once on (provided there aren't any bubbles), it doesn't alter the feel of the screen much, and doesn't affect the sensitivity at all either with your finger or stylus.
The only caution I would throw out is to be careful when installing to avoid any lint under the film. If you've done these kind of protectors before then you probably already know this.
I am currently using spigen crystal clear sp which are very good but a total fingerprint magnet. How are these sp with fingerprints?
ukic said:
I am currently using spigen crystal clear sp which are very good but a total fingerprint magnet. How are these sp with fingerprints?
Click to expand...
Click to collapse
It think it attracts a bit more than the naked screen (which is surprisingly resistant to fingerprints) , but it doesn't seem too bad to me. But...I don't have a lot of experience with different screen protectors. I can say it's better about fingerprints than the naked Nexus 4 and naked Note 1.
stanglifemike said:
Pics
Sent from my White Evo LTE using XDA Premium
Click to expand...
Click to collapse
I have this screen protector, and I havent taken it off to try any of the others I have. It's THAT good. Once you line it up against the fat bottom, just lay it down.
Had some dust, lifted it up and used tape on the screen protector, and put it back down. Now I have ZERO bubbles and it's fantastic. 100000% clarity too. 5 stars.
What is the best (quality and cost) tempered glass screen protector for the G3? I previously had an M8 and bought my first ever tempered glass screen protector, Zagg Glass. It was fantastic, looked and felt like there was nothing there and the application process took 20 seconds. However, I'm sure there are other ones out there that are just as good quality wise but far less expensive. Thanks.
I use this one myself and like it a lot. Nice fit, ultra thin, rounded edges, crystal clear and a 9 hardness. Very satisfied with this one.
Orzly
Just perfect
I use one by Pthink. 9H hardness, very clear, and very very smooth coating which does not leave fingerprints or oil! very satisfied with this purchase and was around $12 on amazon. I prefer this one due to the cutouts up top.
Can you please use the long thread already dedicated to this tooic instead of making a New one please...
Please search before making new threads
Sent from my LG-D851 using XDA Free mobile app
I recommend Bepak H+ have used it on my G3 and HTC M8
My nano.tr was great for about 3 days. Now its coming up in 2 places
I refuse to buy another Spigen Nano t.r after 5 of them with countless issues. Ive had them stop sticking for no reason, crack without ever dropping my phone and the list goes on.
I bought a Mime ghost glass and its a huge improvement. It also only cost 28 with free shipping from their website. Great screen protector especially compared to Spigen.
pic
fullyflaredfred said:
I use one by Pthink. 9H hardness, very clear, and very very smooth coating which does not leave fingerprints or oil! very satisfied with this purchase and was around $12 on amazon. I prefer this one due to the cutouts up top.
Click to expand...
Click to collapse
Any chance you could post a pic, I ordered one and am anxious to see what it looks like exactly.
I use zagg, and it's amazing. I also have the circle wireless case, and the front flap was not affected in any way.
I just got my pThink screen protector in today. It is a perfect fit. Couldn't be happier with the quality and price. I definitely recommend compared to the ones with the big cutout up top...this just has one for the speaker grill and ambient light sensors.
are there any tempered glass screen protector that does not leave any fingerprint behind?
tsktsk999 said:
are there any tempered glass screen protector that does not leave any fingerprint behind?
Click to expand...
Click to collapse
If there were I would assume the same layer/technique would be applied on the original Gorilla Glass screen as well.
Some do claim they repel finger prints, that's usually just marketing BS though
tsktsk999 said:
are there any tempered glass screen protector that does not leave any fingerprint behind?
Click to expand...
Click to collapse
I've been using a Tech Armor glass screen saver for the last few days and it shows fewer fingerprints than the stock screen. It feels smoother than the regular screen which may have something to do with it. It still gets prints, just not as many and they seem to wipe off easier. Very please with it for $10.
jksigmon said:
I just got my pThink screen protector in today. It is a perfect fit. Couldn't be happier with the quality and price. I definitely recommend compared to the ones with the big cutout up top...this just has one for the speaker grill and ambient light sensors.
Click to expand...
Click to collapse
this looks like it only has a cutout for the speaker grille?
[email protected] said:
this looks like it only has a cutout for the speaker grille?
Click to expand...
Click to collapse
The cutout is for the speaker grill and the proximity sensor etc. It does not have an opening for the front facing camera. I've had it for a few days now and LOVE it. The beveled edge is super smooth on the outside edge and the cutout.
jksigmon said:
The cutout is for the speaker grill and the proximity sensor etc. It does not have an opening for the front facing camera. I've had it for a few days now and LOVE it. The beveled edge is super smooth on the outside edge and the cutout.
Click to expand...
Click to collapse
I bought this protector last night and the slim guard case the other day i think ill be good to go! ill post picutres:good:
tsktsk999 said:
are there any tempered glass screen protector that does not leave any fingerprint behind?
Click to expand...
Click to collapse
I bought the one carried in the VZW stores and it really cut down on the fingerprint / smudges - I could really tell the difference. But that protector was .4mm thickness and touch sensitivity became an issue for me. So I bought the .2mm iCarez protector. The thickness was just right, but the oleophobic properties are not as good as the VZW protector.
As always, YMMV.
Based on the reviews in this thread I ordered the pThink protector (Free Prime 2-Day shipping FTMFW).
I can't say enough good stuff about this screen protector. It is available on Amazon for around $11(with free prime shipping if you have it). There are a variety of good tempered glass screen protectors. Most of them simply notch out the top near where the speaker, light sensor and proximity sensor are located. This one has a perfectly aligned oval shaped cutout giving it a much more OEM looking appearance. Like most, the edges are pleasantly rounded.
The package is straight forward, complete with requisite chinglish on the outside. The package is generic, saying it includes a 'homer(sic) button' cover. Which doesn't make sense, and sure enough it doesn't include. Opening it up, you see all of the included materials. Nothing outstanding here other than the actual instructions seem to be in normal English! I didn't look closely but I didn't see any chinglish.
Installation is a breeze but good prep ensures success. I cleaned the screen extensively to remove all traces of oil and dust. Since I am a chemist I used chloroform to degrease the screen. I also used it to degrease my fingers (not something I recommend but it works). Once the screen was clean, I applied the tempered glass screen protector by VERY VERY VERY gently lowering it by its sides. I can't stress the very gently enough. If you do it gentle enough it will rest just above the surface and you can use your fingernail to maneuver the screen protector into perfect position. Then just touch down on the screen and watch the "bubble" of bonding spread across the screen, it just drives the air out. The rigidity of the screen protector results in a perfect bubble-free finish. I couldn't believe how easy it was. Once the screen protector was on, I wiped it down with the included microfiber cloth.
Initial impressions? Damn! It's truly crystal clear, I can't seem to find any visual distortion. Touch feels slightly changed due to the oleophobic surface but its clearly glass and feels like a touchscreen. There is ZERO effect on the touchscreen performance. Also, the oleophobic surface DRAMATICALLY reduces the amount of smudges, it doesn't prevent them but its a huge reduction. I have a few pics of the package before installation. Once I cleaned the screen, I lost my camera (my phone is the camera so I couldn't use it). The edges of the screen protector are within fractions of a mm of the display edges. This is necessary to make installation a little easier and to prevent bubbles. I truly could NOT be happier!
I'm really happy with a Bepak one. Rounded edges, smooth, and feels really great to touch. No scratches at all till now with some rough usage.
Although reading the reviews about the pThink one, I'm going to give that a try when something happens to the current Bepak one.
My current phone is a Nexus 6P and I have been using a Spigen case + an intelliArmor tempered glass screen protector. Both products are excellent and I have been thrilled with them (and the phone), but the battery is starting to go on me so I figured it was time for a replacement. After some research I settled on the XZP (G8142).
I was able to order the Spigen case for the XZP, but intelliArmor does not make a screen shield (that I can find), so I was wondering if anyone has had any experience with Supershieldz before.
I looked at getting the Skinomi skin and just using the part for the screen along with the Spigen case, but I really prefer tempered glass.
Looking forward to my first Xperia phone!
** UPDATE **
The protector, phone, and case all came in. The Spigen case is top notch as expected, as is the phone itself.
The screen protector is also fantastic. I tried putting it on the recommended way (using the guide stickers), but I could never get the right alignment using this method. I ended up free-handing it and lining it up as best I could, and I think I got within a half millimeter or so of a perfect application (the bottom is perfect, the top speaker is slightly off but not enough to be annoying or obstruct the speaker). There were absolutely no air bubbles to smooth out, which surprised me.
GreenDev9 said:
My current phone is a Nexus 6P and I have been using a Spigen case + an intelliArmor tempered glass screen protector. Both products are excellent and I have been thrilled with them (and the phone), but the battery is starting to go on me so I figured it was time for a replacement. After some research I settled on the XZP (G8142).
I was able to order the Spigen case for the XZP, but intelliArmor does not make a screen shield (that I can find), so I was wondering if anyone has had any experience with Supershieldz before.
I looked at getting the Skinomi skin and just using the part for the screen along with the Spigen case, but I really prefer tempered glass.
Looking forward to my first Xperia phone!
** UPDATE **
The protector, phone, and case all came in. The Spigen case is top notch as expected, as is the phone itself.
The screen protector is also fantastic. I tried putting it on the recommended way (using the guide stickers), but I could never get the right alignment using this method. I ended up free-handing it and lining it up as best I could, and I think I got within a half millimeter or so of a perfect application (the bottom is perfect, the top speaker is slightly off but not enough to be annoying or obstruct the speaker). There were absolutely no air bubbles to smooth out, which surprised me.
Click to expand...
Click to collapse
Is the adhesive just on the edges of the Tempered Glass? Is there some oil-like residue between the screen and glass?
I purchased a very similar Tempered Glass protector to the Supershieldz version and found the adhesive is just on the edges, top/bottom/left and right but the entirety of the screen, where the border is not is free to flex and obviously, with the gap that exists without adhesion has an odd oil-like residue, which many users reported.
I have had my XZP for a week now and have not even used it because I want a proper Tempered Glass protector which has received good reviews, along with a folio/wallet/flip case which has a strong latch/magnet to protect the phone overall, along with waiting for a DRM/TA fix before I stop using the Z5P and move onto my XZP.
Mobfigurz said:
Is the adhesive just on the edges of the Tempered Glass? Is there some oil-like residue between the screen and glass?
I purchased a very similar Tempered Glass protector to the Supershieldz version and found the adhesive is just on the edges, top/bottom/left and right but the entirety of the screen, where the border is not is free to flex and obviously, with the gap that exists without adhesion has an odd oil-like residue, which many users reported.
I have had my XZP for a week now and have not even used it because I want a proper Tempered Glass protector which has received good reviews, along with a folio/wallet/flip case which has a strong latch/magnet to protect the phone overall, along with waiting for a DRM/TA fix before I stop using the Z5P and move onto my XZP.
Click to expand...
Click to collapse
Mine has the glue on the edges but there's no oil or anything in the middle.
It looks very similar to the Supershieldz one, might even be a rebrand. It's under the brand name "Panzer Glass".
It works pretty much flawlessly.
Xifar said:
Mine has the glue on the edges but there's no oil or anything in the middle.
It looks very similar to the Supershieldz one, might even be a rebrand. It's under the brand name "Panzer Glass".
It works pretty much flawlessly.
Click to expand...
Click to collapse
The one I purchased is very similar also, but has the cut-out where you can see the Sony 'logo'. Reviews are poor for those, everyone has observed the same issues as myself. I have purchased several other Tempered Glass Protectors, still waiting for them to arrive, different styles and brands to see which is the best fit with the best coverage. I will report back.
Mobfigurz said:
Is the adhesive just on the edges of the Tempered Glass? Is there some oil-like residue between the screen and glass?
I purchased a very similar Tempered Glass protector to the Supershieldz version and found the adhesive is just on the edges, top/bottom/left and right but the entirety of the screen, where the border is not is free to flex and obviously, with the gap that exists without adhesion has an odd oil-like residue, which many users reported.
I have had my XZP for a week now and have not even used it because I want a proper Tempered Glass protector which has received good reviews, along with a folio/wallet/flip case which has a strong latch/magnet to protect the phone overall, along with waiting for a DRM/TA fix before I stop using the Z5P and move onto my XZP.
Click to expand...
Click to collapse
I didn't actually notice if the adhesive was along the edges or the entire piece of glass, but it seemed like the whole piece had adhesive when I peeled off the protective plastic before applying.
I have been using the phone with the protector for about two weeks and here are my observations:
I have moved my thumbs with ample pressure across the face of the protector to see if the glass shifts or moves. It hasn't budged.
No oily residue or weird artifacts.
The fit is quite nice. Without a case, the edges would be noticeable, but with the Spigen case on you can hardly tell there is a screen protector.
In bright/direct sunlight or when you hold the phone in bright light just right you will see a grid of dots on the LCD screen - I don't know if this is because of the protector or the screen itself. It doesn't bother me as it is not noticeable the majority of the time.
My account is too new to link to external sites, so just search supershieldz xperia xz premium on Amazon and it should come up.
GreenDev9 said:
I didn't actually notice if the adhesive was along the edges or the entire piece of glass, but it seemed like the whole piece had adhesive when I peeled off the protective plastic before applying.
I have been using the phone with the protector for about two weeks and here are my observations:
I have moved my thumbs with ample pressure across the face of the protector to see if the glass shifts or moves. It hasn't budged.
No oily residue or weird artifacts.
The fit is quite nice. Without a case, the edges would be noticeable, but with the Spigen case on you can hardly tell there is a screen protector.
In bright/direct sunlight or when you hold the phone in bright light just right you will see a grid of dots on the LCD screen - I don't know if this is because of the protector or the screen itself. It doesn't bother me as it is not noticeable the majority of the time.
My account is too new to link to external sites, so just search supershieldz xperia xz premium on Amazon and it should come up.
Click to expand...
Click to collapse
Appreciate the feedback. I have just taken possession of a Muvit Tempered glass, it is clear without any borders but just the same as the rest. Everyone I have tried thus far has adhesive only on the edges, the larger portion of the screen is free to flex and move and due to that, requires a firmer press and in doing so, you hear a crisp packet like noise, a sort of crunching sound. Really annoying me now, but it is due to the curvature of the screen that we are seeing a lack of good quality glass protectors. For the Z5P I found P-Think on Amazon to be the best, yet to find any suitable candidates for the XZP.
I will order a double pack of Supershieldz soon.
Attached are the photos of the 6T solid suit and the impact screen protector that I just installed this morning. The solid suit feels amazing and the screen protector is film and feels like glass, but is definitely not glass, just so there is no confusion there. It does seem to go from left edge to right edge completely and where I placed it seems to cover the entire screen top to bottom. The slider on the case really works and the buttons are fantastic; smooth and clicky, not at all hard to press. I love both and I'm glad I got them ordered on Black Friday now because two protectors and a case was not inexpensive but they are both super high quality and way more affordable than the glass one from T-Mobile so I'm happy with my purchase. If you have any questions I'll try my best to answer them!
Also, don't mind the doggo, she likes being in pictures.
Can u tell me how the side buttons are? Are they still clicky? Or are they mushy like the stock case that comes with the phone....
And how's the slider button? Is it flimsy?
lemonspeakers said:
Can u tell me how the side buttons are? Are they still clicky? Or are they mushy like the stock case that comes with the phone.... Nn
And how's the slider button? Is it flimsy?[/QUOTENnnnn n N
The buttons are great, I handed someone else my phone so two people could verify that they are very clicky and easy to push. The slider has some play in it up and down but it does work correctly when it hits the slider on the device. No issues with functionality at all this is a really great case.
Click to expand...
Click to collapse
I tried crashguard on op6 and hated it. I think I'll like the solid suit better. Thanks for the pics. Screen protector is intriguing also, seems very clear....
Thankfully I waited I can get the print backs now. Just waiting or one particular one to be available
Is the screen protector you have on This one? It says "Not Full Coverage" on it... I can't see clearly on your photos how close to the edge of the screen the screen protector comes to... I had the same impact screen protector on my old Samsung Galaxy S7, and it didn't even cover the full screen on the left and right, which is the reason I didn't order this screen protector for my 6T..
how slick is the screen protector compared to the pre-applied plastic one from OP?
gregwee said:
Is the screen protector you have on This one? It says "Not Full Coverage" on it... I can't see clearly on your photos how close to the edge of the screen the screen protector comes to... I had the same impact screen protector on my old Samsung Galaxy S7, and it didn't even cover the full screen on the left and right, which is the reason I didn't order this screen protector for my 6T..
Click to expand...
Click to collapse
Sorry about the late response I'm traveling abroad. I have the impact screen protector as the tempered glass one is for the back I think. Anyway, as far as not full coverage I think what they mean is that it covers the visible screen but not the edges past that. It doesn't extend fully top to bottom either but it does cover all the visible screen space as far as I can tell; no obvious cutoff of the screen though it does require precise placement to line it up properly.
Frankenscript said:
how slick is the screen protector compared to the pre-applied plastic one from OP?
Click to expand...
Click to collapse
Much slicker definitely. Feels like glass but definitely doesn't get rid of oil the way glass does. It feels good to the touch and it is very strong as I dropped on a stool and it bounced onto a hardwood floor right after that. There was no damage to the screen, but the protector did crack so I'll replace it when I get home. It did very well holding up to direct impact on a metal stool; lived up to the hype for me.
Can u take better pictures of the screen protector again?
AlkaliV2 said:
Much slicker definitely. Feels like glass but definitely doesn't get rid of oil the way glass does. It feels good to the touch and it is very strong as I dropped on a stool and it bounced onto a hardwood floor right after that. There was no damage to the screen, but the protector did crack so I'll replace it when I get home. It did very well holding up to direct impact on a metal stool; lived up to the hype for me.
Click to expand...
Click to collapse
The impact resistance shatters? I thought it was some type of plastic film.
https://imgur.com/a/BJD1GmC
I also purchased a SolidSuit (with the lens mount) for my 6T and while I like the build material, I don't like the little details. Let me explain:
1) The back of the case has this weird look and feel like it's made from three separate medium-fiber density board with a black sticker over it. I can actually feel the transitions between the three pieces and I don't like it. See the attached picture.
2) There is a noticeable gap at the top of the phone where the back meets the bumper edge. However, on the bottom, it's completely flush. My pockets are clean, but somehow dust and small particles find its way into that tiny gap. Ugh,
3) The special lens adapter is amazing since I am now able to mount the Moment 18mm WIDE V2 lens. However, since the bayonet mount sits so far away from the camera lens, it creates vignetting. FYI: The OP6T and the OP6 share the same lens adapter. I bought both. They are labeled differently, but they are identical in every way: height, mounting point, etc. If they did this correctly, the adapter for the OP6T should be SHORTER since it does NOT have the same camera height protrusion as the oneplus 6.
https://imgur.com/a/BJD1GmC
zymphad said:
The impact resistance shatters? I thought it was some type of plastic film.
Click to expand...
Click to collapse
It didn't shatter really, it just cracked along a seam where the impact was. When I get back home in two days I'll try to get pictures of the crack and the screen protector.