[Solved] No Network Service after flashing NG3 - T-Mobile Samsung Galaxy S 5

Under status, Network shows as 'Unknown', Mobile network type shows as 'Unknown', Service state is 'Out of service', and Mobile network state is 'Disconnected'.
IMEI shows as nonnull (valid), and IMEISV shows as nonnull (valid). I'm not sure where the issue is, i'm assuming it is somewhere in the modem, but I flashed the NG3 Modem multiple times.
Not really sure what is wrong, can anyone suggest anything to restore my phone before I try something else again?

..

fffft said:
You didn't give us very much detail about anything from what firmware build you tried to flash to what model of S5 you have, screen shots of your phone information in the settings menu or anything else. Which makes it impossible to delineate what happened.
At a guess and that is all that is possible without a detailed description of your configuration.. it sounds like you may have flashed the wrong firmware - intended for another carrier or S5 variant. Which sometimes screws up wifi /bluetooth or occasionally bricks a phone. Check that your firmware build md5 checksum is valid, that the firmware is intended for your native carrier and variant. And if you were flashing a modem separately, confirm that it is for your carrier and matches your baseband (bootloader). Failing that, restore your backup to recover.
If you don't have a backup for some reason, that should be very high on your list of things to start doing. In that situation, download a full stock firmware that is for your specific phone model and carrier, wipe the cache partition and you should be good. In some cases you may also need to do a factory data reset (do that as a last resort, since it will delete your photos, user files, etc).
.
Click to expand...
Click to collapse
I downloaded the stock tar (the full one) here, and selected AP with it. To be sure that my bootloader is updated, I later used the modem/booloader here and I used the right one (900T) and followed the guide at the top of that page for setting "BP" for bootloader and "CP" for modem. When I run the bootloader check command (getprop ro.boot.bootloader), it returns NG3, so I think that's fine too.
I have the 900T (well, this IS the t-mobile galaxy s5 thread).
I probably should have backed up, but I tend not to because I have rarely ran into issues on my previous Note 2 and the times I did, the backup wouldn't have fixed it (usually because the recovery was too big or the modem got corrupted).
And I did use factory reset multiple times, I don't have much on the phone right now and also have an external sd card where I store most of my things anyways.
Specifically, what part of the settings would you want to see?

..

NG3 Full Stock Tar: http://www.androidfilehost.com/?fid=23578570567722728
^ That was what I used under AP.
When I try to repartition, is says "Erasing USERDATA Partition...\nSECURE CHECK FAIL : PIT".

..

fffft said:
Suggesting that you have partition corruption. The purpose of my earlier suggestion to flash the PIT file was to resolve potential partition corruption. So you could do far worse than follow the suggestions in my last post.
.
Click to expand...
Click to collapse
No longer boots after nand erase all. Since the partition failed, I unchecked it and just left NAND erase checked.
Any other suggestions?

rmanne said:
No longer boots after nand erase all. Since the partition failed, I unchecked it and just left NAND erase checked.
Any other suggestions?
Click to expand...
Click to collapse
I don't know why or what @fffft is trying to get you to do but touching the things you are could end up bricking your device if not too careful.
All you need to do is select the full tar file under "AP" and uncheck the reboot and F reset time options.
EDIT: You need to extract the tar file to get the MD5 file that is what you flash in Odin.
If you have no data, just check that the APN settings are properly configured.
I had to flash the tar file a couple times before the modem upgraded. But don't touch PIT or NAND erase.

..

fffft said:
You can't do a normal boot after erasing the NAND, since that has wiped our your system files. That isn't unexpected. But your phone will still boot to download mode, sometimes called "Odin" mode. Volume down + home + power.
Once your write a replacement firmware image it will boot normally again. Writing a full image is recommended. Odin can be fussy and seemingly a bit more so with larger writes than when flashing smaller writes. And possibly easier with earlier S5 firmware builds (not proven, just an impression).
If you persist Odin will write the image, it just takes several attempts sometimes. If a given write fails, do not reset Odin on your PC, just pull the phone battery, replace it.. boot to download mode again and flash again from the open Odin window. Inevitably the flash will succeed the second time even though Odin balked the first time. If you have persistent problems, try a different USB cable and USB port.
The poster above doesn't understand what the NAND or partition features accomplish, but anyone doing their due diligence would find informed threads supporting my recommendations when partition corruption is suspected or needs to be repaired.
..
Click to expand...
Click to collapse
I didn't just erase the NAND though, I also added the .tar.md5 file that I pointed to earlier, which should have added back the system files. Well in any case, I flashed TWRP, and according to it, the Data partition was not properly partitioned (and thus not mounted) and I wiped that with TWRP, and installed another custom ROM (ViSiX), and it has the same issue right now ("Searching").
I did try the earlier S5 images (NF6, which is what the phone initially came with), and I flashed the proper modem/bootloader there also, but it still has no service.
I know that the sim card is working because I still have my other phone (note 2), and it works fine in that. I still don't understand what about the S5 that is not working. It doesn't even say no service anymore. It's just searching...
by replacement firmware image, do you mean the whole stock rom image? Or do you mean just the firmware, as is given in that stock collection thread.

elesbb said:
I don't know why or what @fffft is trying to get you to do but touching the things you are could end up bricking your device if not too careful.
All you need to do is select the full tar file under "AP" and uncheck the reboot and F reset time options.
EDIT: You need to extract the tar file to get the MD5 file that is what you flash in Odin.
If you have no data, just check that the APN settings are properly configured.
I had to flash the tar file a couple times before the modem upgraded. But don't touch PIT or NAND erase.
Click to expand...
Click to collapse
Also, 'had to flash a couple times'? Why on earth would there be non-determinism involved in a phone? I'm genuinely confused.
APN settings appear to be the exact same as my previous phone, and it shouldn't be the issue anyways because the APN is only useful to look at for network use right? I can't even call/text, since it says that I'm not registered on the network.

rmanne said:
Also, 'had to flash a couple times'? Why on earth would there be non-determinism involved in a phone? I'm genuinely confused.
APN settings appear to be the exact same as my previous phone, and it shouldn't be the issue anyways because the APN is only useful to look at for network use right? I can't even call/text, since it says that I'm not registered on the network.
Click to expand...
Click to collapse
I don't know why but the baseband doesn't always flash. So flashing it twice in a row usually does the trick,
Sent from my SM-G900T using Tapatalk

I did just try the install modem twice in a row with no luck.

What's the best recovery to use with this phone? I'm using the twrp that you can download on their official website right now, but from what I remember, on the Note 2, if you install using the 'wrong' version of TWRP, your service won't work.
Also, another thing that I've noticed is that during the initial one time initialization, instead of saying "Samsung Galaxy S5 (T-Mobile)" (or something like that), it is now saying "Samsung galaxy S5" without the T-Mobile addition to it. I think that it has to do with the recovery that I flashed, since it's what determines the phone model more than anything.
EDIT: used to say "Galaxy S5 ..." and now says "Galaxy S5"

rmanne said:
I did just try the install modem twice in a row with no luck.
Click to expand...
Click to collapse
I'm talking about the entire md5 file.
I use twrp.
Sent from my SM-G900T using Tapatalk

elesbb said:
I don't know why but the baseband doesn't always flash. So flashing it twice in a row usually does the trick,
Sent from my SM-G900T using Tapatalk
Click to expand...
Click to collapse
Does the download mode have something to do with it?
On mine, it says:
ODIN MODE
PRODUCT NAME: SM-G900T
CURRENT BINARY: Custom
SYSTEM STATUS: Custom
KNOX WARRANTY VOID: 0x1 (2)
QUALCOMM SECUREBOOT: ENABLE (CSB)
RP SWREV: S1, T1, R1, A1, P1
UDC START

elesbb said:
I'm talking about the entire md5 file.
I use twrp.
Sent from my SM-G900T using Tapatalk
Click to expand...
Click to collapse
Yep, I was trying to install the entire md5 ("G900T-UVU1BNG3-MODEM.tar.md5"), unless you meant the full stock rom.

..

fffft said:
We're assuming that your stipulation that the IMEI is valid is correct. I'd look at the service mode menu and check the certificate status to confirm that if you haven't already.
You could also do a search to see if anyone is having problems with the most recent G900TUVU1BNG3 firmware. Or even better temporarily revert to the a known stable, earlier firmware version. If you flash a full firmware image from May, your certificate status is valid and your APN info is correct then you'd have a reasonable basis for suspecting a hardware failure.
Hardware is unlikely though unless you can associate it with trauma or pre-existing symptoms, none of which you mentioned. Network connectivity issues inevitably arise from flashing a modem or firmware image intended for a different platform, a corrupt cache or corrupt system files.
.
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=2754957
^ I ran through that first post, and did as it said without any improvement.
How do I check the certificate status?
From what I can tell, no one else is having the issue (or at least no one has yet posted about it). And as I've already said, NF6 didn't work either (it was working when I got my phone, but now doesn't work after trying to revert everything to stock).
APN info is certainly correct.
I didn't unbox this phone, so I'm not actually sure that it's the right model, but its first boot showed the 'T-Mobile' display screen, so I see no reason to doubt that it's a 900T. I will recheck this just in case.
EDIT: I found the certificate status i think
The page says "IMEI Certi: PASS, 1\nUnknown"
also includes "REJECT:6, LU_ATT#: 0", "SERVICE : LIMITED", "STATE: DEREGISTR SUB:1", "PA STATE:0(ET),HDET:0", "and a bunch of numeric values above it. Band 4, BW 10MHz, MCC-MNC, TAC, Earfcn_dl, PCI: 0, RSRP -94, RSRQ -10, SNR 17.4-22.1
What does it mean? What is "LU_ATT"?

Solved!
For whatever reason, it seems that the person who sold the phone reported it as stolen (according to T-Mobile customer service, a phone marked as lost will not be able to access network services) at around the same time that I flashed the update. I did think something was fishy since I didn't immediately lose network. I feel like I was on NG3 for at least a few hours before it stopped working, but I thought I might have just been imagining things, since the timing was just too close to properly make a note of.
Well, thanks anyways, I appreciate the time you two took to attempt to help.

Related

Unusual thing with official firmware package? Seems corrupts but flashes fine?

Hi guys n girls,
I am sort of new to the Ace section here. I am doing a re-vamp of my mum's phone and said I would spruce it up a little. Shame there is no decent CM 9 versions that I can get working because of lack of RAM....the only one listed (no disrespect to the dev - thanks for making it available on such a low spec device!) but it doesn't work with my Optus GT S5830V (5830I) for some reason?
Anyway to my point, I have downloaded several versions of the stock firmware from Sammobile. The odd thing is that I cannot extract that firmware at all. Every archive program I have sees it as either being not an archive; corrupt or fails to extract it? So I am unable to make my own 4 part Odin recovery package. Making my own will save time; at the moment I have to flash the 4 part Odin (return to stock) package, then reboot into download mode again and then flash the stock firmware?
3 things I noted.
1). The device is not detected by the so called Odin specific for Ace and variants that uses an Ops type PIT file? The device is plugged in and all drivers upto date....it' just plain doesn't see it? It is however detected and flashable (albeit without an .ops file) using the 4 part package on Odin 3.07 made for my Galaxy S3?
2). I am unable to get any detection with EFS pro and it returns no PIT file?
3). All attempts to extract the stock Optus firmware package fail. I have removed the .MD5 file extension (only needed for preserving file naming conventions anyway - i.e. If you rename any .tar.md5 firmware package, in order to be able to flash it you need only to remove the .md5 from the end and leaving it as .tar and the firmware will flash without error. I digress.....What does someone suggest for me to being able to make my own firmware package based on stock?
First off, wrong section.
Jarmezrocks said:
Shame there is no decent CM 9 versions that I can get working because of lack of RAM....the only one listed (no disrespect to the dev - thanks for making it available on such a low spec device!) but it doesn't work with my Optus GT S5830V (5830I) for some reason?
Click to expand...
Click to collapse
1) We don't have a stable CM9 because our devs don't have the source code for all the drivers, not lack of RAM.
2) Have you formatted your system's partitions to the EXT4 filesystem? CM requires an EXT4 filesystem to operate.
Jarmezrocks said:
Anyway to my point, I have downloaded several versions of the stock firmware from Sammobile. The odd thing is that I cannot extract that firmware at all. Every archive program I have sees it as either being not an archive; corrupt or fails to extract it? So I am unable to make my own 4 part Odin recovery package. Making my own will save time; at the moment I have to flash the 4 part Odin (return to stock) package, then reboot into download mode again and then flash the stock firmware?
Click to expand...
Click to collapse
Jarmezrocks said:
3). All attempts to extract the stock Optus firmware package fail. I have removed the .MD5 file extension (only needed for preserving file naming conventions anyway - i.e. If you rename any .tar.md5 firmware package, in order to be able to flash it you need only to remove the .md5 from the end and leaving it as .tar and the firmware will flash without error. I digress.....What does someone suggest for me to being able to make my own firmware package based on stock?
Click to expand...
Click to collapse
The tar.md5 file has to split into the PDA, CSC, Modem and PIT files using Odinatrix. Search for it.
Jarmezrocks said:
3 things I noted.
1). The device is not detected by the so called Odin specific for Ace and variants that uses an Ops type PIT file? The device is plugged in and all drivers upto date....it' just plain doesn't see it? It is however detected and flashable (albeit without an .ops file) using the 4 part package on Odin 3.07 made for my Galaxy S3?
Click to expand...
Click to collapse
The Odin specific for Ace you stated above might be for GT-S5830. For the variants running the Broadcom BCM21553 the Odin version to use is v1.84. Odin v3.07 is more like a universal Odin that works on most devices.
Jarmezrocks said:
2). I am unable to get any detection with EFS pro and it returns no PIT file?
Click to expand...
Click to collapse
I don't know about this.
NightRaven49 said:
First off, wrong section.
Click to expand...
Click to collapse
Why? I was not actually asking for support as such, just sharing what I learnt/noticed.
NightRaven49 said:
1) We don't have a stable CM9 because our devs don't have the source code for all the drivers, not lack of RAM.
2) Have you formatted your system's partitions to the EXT4 filesystem? CM requires an EXT4 filesystem to operate.
Click to expand...
Click to collapse
Yes I am aware of that. I actually did attempt to flash the CM9 developer package several times all without result.
I tried many methods, firstly the conventional method and then several other unconventional methods. I first flashed CWM recovery 6.0.0.x (something around there) and that was ok but it could not detect the partitions....naturally I was on the standard firmware!
So I then flashed Thunder kernel which allowed recovery to see and mount all the partitions as well as prepare for a CM firmware flash. As I knew that CM required EXT4 I was prepared and flashed Rio's Ext4-RFS conversion script via Aroma in recovery. This worked very well. Only issue was that in doing so it corrupts the system partition and then I am unable to mount it anymore to flash CM.
Returning to stock or even attempting a nandroid restore from this point forward was fruitless as you can imagine. I tried several other combinations before retiring the idea. These included full system wipe after flashing CWM recovery (I figured maybe having data on the partitions its self could be interferring with the EXT conversion scripts? Everything seemed fine and ran correctly as expected only no system mounting.
I tried another method of flashing a ROM that included a kernel with it based on CM7 in the hopes that migrating to CM9 would be easier; this was not the case.
I picked a CM7 ROM that had a conversion script built in for BML to MTD. After returning to stock base via Odin I proceeded to flash recovery 6.0.0.x again, then I immediately flashed CM7 in the hope that I would kill two birds with 1 stone and have CM do its conversion on the fly as well as install (alleviating the need for mounting system after migrating to Ext4). This ROM installed without fault. All was well until I rebooted expecting to boot into CM7....this wasn't the case, I received bootloops like crazy. Naturally I booted into recovery (the ROM had downgraded me to version 5.x CWM recovery - that is fine anyway); I proceeded by clearing the caches and performing a factory reset (note This usually a good thing to do anyway regardless if you came from a clean reset factory firmware or not).
After doing this and rebooting the device reboots continuously as it did prior. I again decided to re-install the same zip as I am aware with changing to CM on many other devices it can sometimes require flashing 2-3 (and sometimes even 4) times for a firmware update to stick. Again still no response and forever bootloops. I decided at this point that if I was to waste the time and effort in Odin'ing back to stock AND THEN flashing my standard firmware that I should try another CM ROM.
I had CM9 available and even though half hour prior I was unable to mount the the system partition, I thought maybe that CM7 had been flashed first so if CM9 can see and mount partitions (like it should have originally) then I could flash CM9 in a hope that it might wipe out what ever was causing all the issues with bootloops.
CM9 installed correctly, however again I could not boot the device at all! I had read a post from a forum member's guide saying that if I got some of these issues that I should flash back to base and try it again. I did this another 3-4,5 times at least, various combinations of wiping base firmware, not wiping base firmware, wiping CM7; not wiping CM7......Always the end result = bootloops.
As you can imagine it was rather annoying if I was returning to base firmware (if I wanted to be stock carrier branded again I needed to flash twice, once to return to stock and again to flash Optus firmware.
Overall I was unable to get any firmware booting besides that which was provided as an Odin package AKA stock firmware. If I flashed a custom recovery over stock firmware I was unable to boot again. Oddly enough I found a standalone version of CWM recovery version 5 that was not CM specific and I performed a backup as it was able to see the stock partitions without throwing errors.
I then opted to do a conversion to EXT4 again and hoped that I could just restore my nandroid backup of the stock partitions like recommended in may of the guides for Galaxy Ace.
Unfortunately again I was unable to boot and the partitions become unmountable leading to yet again flashing back to base unbranded, then flashing stock carrier branded firmware (this has the correct modem for the carrier and region).
At this point I retired the idea of custom firmware. I will later root the device and just leave it on 2.3.7 and do internal/external SDcard swap and flash a theme and maybe a few compatible APKs from newer stock firmwares (at least ICS) to achieve the functionality I was hoping to have by flashing and using ICS. I found the best and most simplest way of achieving this was through Moto-Chopper Root method and adb, most of the documented ways of achieving root on the Ace don't work for the S5830V for some reason. So I will stick with what works.
NightRaven49 said:
The tar.md5 file has to split into the PDA, CSC, Modem and PIT files using Odinatrix. Search for it.
Click to expand...
Click to collapse
Thanks for the tip. :good: I have downloaded this ready now, so I will investigate how this goes? It looks very similar to a application I already use TAR.MD5_PACKAGER however I see it has an option for extracting from .tar.md5 files that have malformed header information. So that sounds like it should do the trick!:fingers-crossed: Do you think that this is maybe intensional as a means of stopping people like us from building custom firmware packages?
I mean the .tar.md5 package flashes perfectly as it should do which is very surprising seeming .md5 signature is very easily broken when you rename the file and you have not even opened it. That was what lead me to flashing it in the first place, I mean I figured that if the .tar.md5 was so corrupt as I believed it was, then the worst that can happen will be Odin will spit an error message and not proceed i.e. it won't even attempt to flash the said firmware!
Myself if I download any firmware that doesn't flash and fails due to md5 error, I immediately open it up and inspect it and unless it was extremely difficult to obtain (I have waited close to 30 hours once for an old firmware package to download from the only source I could find - but regardless if it was damaged or not I only wanted the old bootloader so I could integrate it into a new firmware package so the passing md5 was relatively unimportant), I would just re-download it again.
The fact that ALL of these packages for S5830I are like this (regardless of what browser or means I downloaded the package) and the fact that they DO in fact flash like normal packages, and the phone returns to 100% factory condition; tells me that this does look like a means of discouraging custom firmware developers? hmmm
NightRaven49 said:
The Odin specific for Ace you stated above might be for GT-S5830. For the variants running the Broadcom BCM21553 the Odin version to use is v1.84. Odin v3.07 is more like a universal Odin that works on most devices.
Click to expand...
Click to collapse
The device is actually a S5830V...the V devices are relatively undocumented, but they are essentially just the same as the more common i/M variants. I did my homework first with this, and I can most certainly attest that it is NOT the S5830. I wouldn't attempt flashing S5830 firmware, also S5830i firmware boots and functions as normal and has signal albeit not so strong when the modem is not for our carrier and/or region, but function none the less.
NightRaven49 said:
I don't know about this.
Click to expand...
Click to collapse
Well give the fact that I had performed so many download of firmware that I initially believed to be corrupt I was unable to extract the PIT (or in the case of the generic Ace OPS file) from the firmwares.
Being the fact that there was little known about the S5830V I was unsure if to proceed of not? There are few reports on the device and most of them were of owners bricking their device, only 1 report I know of where a V owner claimed he flashed S5830i firmware without a hitch, again he was not from Australia where I am from, so I was flying blind and scared I was going to brick the device.
At the very least if I had a PIT file I could analyse it and could manually make image backup of the EFS/IMEI partition straight after rooting the phone. I have looked already at scripts that scan the whole emmc and I hit a snag when the kernel I am using is not insecure i.e. adb cannot run as root. I have root and confirmed with root checker app but terminal emulator and/or command line are unable to obtain root
Anyway to shed some light for you EFS Pro is a means of doing this that works on most Samsung devices....just not the Ace as far as I can tell.
Yes I am already aware that there is Galaxy Toolbox and I had actually gone ahead and done all that already,but an incident more recently where I had a device I was repairing with a wiped IMEI and it actually refused to boot. This becomes a hassle when restoring the IMEI cause in order to have Galaxy Toolbox you need to be booted and rooted. I wasted a whole day repairing the IMEI. So pretty much the message here is what good is Galaxy Toolbox to me restoring the IMEI if it can't boot? NONE!
I contacted the developer weeks ago and explained my situation and he is still yet to respond. I explained that I had a V variant of the Ace and wanted to ensure I had all bases covered. I requested information on how I could open the IMEI manually outside of the Galaxy Toolbox in the case that it would not boot (as this was how I restored the other device last week and it worked), unfortunately I am still yet to hear a response form him? Slack.
When I obtain this information I will share it here on XDA in the hopes that people in Australia with this variant will search and find some info on it. This is also why I am making this post here so detailed for folks like me who have been searching fruitlessly for answers.
My thoughts are that maybe there is something still not 100% the same between the i and the V because all custom firmwares I tried made for the S5830i never worked?
There is maybe an issue with how they are scripting their installs that is causing issues, but it is worrying enough that flashing so far has lead to partitions becoming corrupted very easily. I have had this before with my own phone more recently because a dev made a simple mistake in an updater script that called an explicit partition by mounting point ID and not by a more generic mounting point like "/system", "system" which lead to lost IMEI and bricked phone.
I am not blaming the dev though because it is easy to assume that a even though the mounting was non-specific for my device and the partition being called was not actually the EFS, it should not have corrupted my EFS....but that is not true, so a discovery was made and a lesson learned from all this. I managed to revive my device and it lived to fight another day, but simple mistakes made in ignorance or lack of information can still be costly mistakes. Need I say more.
I will report back when I have got a proper partition map for the S5830V and all will be happy days
I don't feel like quoting anymore, but I do spot some anomalies.
1) ...we don't have CWM 6.0.0.x. Are you sure you used the 5830i CWM, not the 5830?
2) I was referring to some other version of Odin when you said the Odin version specific to Ace. Which version were you using then?
3) I don't see how rio's multi-formatter can render the system partitions unmountable. In that case try lopicl.00's EXT4 formatter. Go search for it. After formatting flash Biel's Specific Basic kernel.
also you were asking a question, so naturally this should be in Q&A.

[Q] Soft Bricked...Need Quick Advice

Hey all. I had Hypderdrive installed. I updated it to 21 but had a force close issue. I wiped to reinstall in safestrap and realized that I didn't have the ROM on the device anymore. Whoops. All of a sudden I had no OS and couldn't connect to the phone via USB to put the ROM onto it.
After trying some stuff I got a bit more stuck. I can only reboot into 3 places: 1) Download mode (with volume down) 2) stuck at samsung unlocked icon (no buttons pressed) and 3) default recovery mode (with volume up). I tried with Kies to just install the latest firmware, figuring I'd be happy with lollipop and just go ahead and get a new phone in the near future. That firmware upgrade process fails right when the status bar shows up on the screen. Now rebooting the phone says Software Update Failed.
What are my options via Kies, Odin, or something else to either get back to rooted Hyperdrive or just get the latest firmware up and running? Thanks!
ODIN v3.10
https://docs.google.com/file/d/0B4RU_ZH5QUASNmxLX3JpejBXREE/edit?usp=docslist_api
This is the SCH-I545 lollipop image:
https://docs.google.com/file/d/0B4RU_ZH5QUASaU9LcDJ3WWZfdXM/edit?usp=docslist_api
And once you go forward..There is NO ROOT or ROMMING!!!
If you want to stay NK1 and ROOT:
https://docs.google.com/file/d/0B4RU_ZH5QUASdHE1b2Q2NXpVX0U/edit?usp=docslist_api
In ODIN, WITH EITHER file select these checkboxes:
Auto-Reboot
Re-Partition
F. Reset Time
NAND Erase All
Phone Bootloader Update
Phone EFS CLEAR
Thanks a ton. Haven't gotten it to work yet. I followed your directions and Odin fails with "SW REV. CHECK FAIL : fused : 7, Binary : 6". My guess is that is a mismatch of the bootloader versions? I believe I was on NC5 before, so I tried flashing the No Wipe file from here: http://forum.xda-developers.com/showthread.php?t=2735172 and had no luck.
Any idea what version I should be trying to get it to work? Thanks for the help so far!
No. That means you are on lollipop Bootloader already! You have to flash lollipop
KaosMaster said:
No. That means you are on lollipop Bootloader already! You have to flash lollipop
Click to expand...
Click to collapse
Yup. Learned that while I was thinking about it. Such is life, right? Currently trying to just get OC1 installed via Odin but it keeps failing late in the process with XmitData_Write. If anyone has an idea beyond changing cables and ports (which I'm doing now) then I'm all ears.
Quick update. I've been following the instructions and advice from this thread: http://forum.xda-developers.com/galaxy-s4-verizon/help/unbrick-taking-oc1-t3122230
I have not yet gotten my phone working, but have made slight progress. I'm currently flashing from the Software Update Failed screen and not the Odin Download Mode screen. I've been checking all the listed boxes. I've tried flashing as CSC and as AP and it is now failing on the NON-HLOS.bin file. It's failed there 4 or 5 times now.
Any advice on what changes to try next?
volantis said:
Quick update. I've been following the instructions and advice from this thread: http://forum.xda-developers.com/galaxy-s4-verizon/help/unbrick-taking-oc1-t3122230
I have not yet gotten my phone working, but have made slight progress. I'm currently flashing from the Software Update Failed screen and not the Odin Download Mode screen. I've been checking all the listed boxes. I've tried flashing as CSC and as AP and it is now failing on the NON-HLOS.bin file. It's failed there 4 or 5 times now.
Any advice on what changes to try next?
Click to expand...
Click to collapse
the Single Service File goes in the CSC box. Not sure why it keeps failing, but my OPinion is that you should Try to Load into Recovery, Perform A Factory Data Reset then Try again!
Flash with the Check-Boxes befoire without the "Phone EFS Clear" option...When THe phone turns on....if it is The firmware Recovery screen...Flash there, if it is the Samsung LOGO, Pull the Battery, and LOAD into "Odin Mode" and Flash AGAIN There!
KaosMaster said:
the Single Service File goes in the CSC box. Not sure why it keeps failing, but my OPinion is that you should Try to Load into Recovery, Perform A Factory Data Reset then Try again!
Flash with the Check-Boxes befoire without the "Phone EFS Clear" option...When THe phone turns on....if it is The firmware Recovery screen...Flash there, if it is the Samsung LOGO, Pull the Battery, and LOAD into "Odin Mode" and Flash AGAIN There!
Click to expand...
Click to collapse
Thanks. I finally got it working. I'm not sure exactly what did it. I kept trying various combinations of flashing at CSC or AP and in Download mode and Software Upgrade Failed. I believe the one that actually took was the Sammobile stock OC1 file flashed as AP, but I'm not 100% and not sure that really is what made the difference. I did have all the options checked when it finally took.
After the Odin flash passed it did just boot to a black screen with the LED on solid blue. I went to recovery and did a factory reset and the phone booted up. Maybe that'll help someone else.
Don't have root anymore, but Lollipop seems like a very nice update coming from KK.
Thanks! - but still in trouble.
Spoke too soon!! Yours was the only one that actually loaded with Odin. After that phone will not reboot, just comes on for 2 seconds and then turns off. Any ideas would be greatly appreciated.
I have tried the following firmware versions, except for yours, they all get fused: 7 , binary : 6:
I545_VZW_I545VRUDMI1_I545VZWDMI1_Original
I545_VZW_I545VRUEMJ7_I545VZWEMJ7_Original
VZW-I545VRUFNC5-20140429111807
VZW-I545VRUFNG6-20141021092718
plus several others
--------------
Thanks, bricked my Verizon S4 and tried 5 different firmware files, including the ones from the Samsung site. Yours is the only one that worked.
Looks like you need to flash a more recent file. You'll probably have to go with the latest stock version without root.
volantis said:
Looks like you need to flash a more recent file. You'll probably have to go with the latest stock version without root.
Click to expand...
Click to collapse
Sorry, thought I updated the post. I tried again and the second time around it worked all the way through with the file on this thread.

[RESOLVED] Help upgrade a SHV-E160S 4.0.4 IMM76D.VH29 to latest??

Hi guys!
This is my first time to post a thread in this forum, I just bought a Samsung Note with model SHV-E160S, Android Version 4.0.4 and Build# IMM76D.VH29. I know that this is a Korean Variant and I'm using it here in Philippines (I can send SMS -- Openline). I don't know if this phone is already rooted, I don't know how to check.
What I'm trying to accomplish is to upgrade this phone from 4.0.4 to 4.1.2 then later on upgrade it to Android Lollipop 5.1 and I don't know how. It will be a great pleasure if someone help me or direct me on what should I do.
I'm totally new to android devices and I'm not familiar on how to upgrade,update or root an android device.
Thanks!
Hello guys, any ideas? Thanks!
jakeortega said:
Hi guys!
This is my first time to post a thread in this forum, I just bought a Samsung Note with model SHV-E160S, Android Version 4.0.4 and Build# IMM76D.VH29. I know that this is a Korean Variant and I'm using it here in Philippines (I can send SMS -- Openline). I don't know if this phone is already rooted, I don't know how to check.
What I'm trying to accomplish is to upgrade this phone from 4.0.4 to 4.1.2 then later on upgrade it to Android Lollipop 5.1 and I don't know how. It will be a great pleasure if someone help me or direct me on what should I do.
I'm totally new to android devices and I'm not familiar on how to upgrade,update or root an android device.
Thanks!
Click to expand...
Click to collapse
Hello guys, any ideas? Thanks!
You'll be able to find your firmware here https://mega.nz/#F!IxJTDDQQ!TTgzxjX8d7EnzemoIj0ogg
4.1.2 was the last official update from Samsung for your device. If you want to update to newer than that, it will have to be done via updating with a custom recovery and custom rom, such as TWRP recovery and CyanogenMod 11 or 12/12.1.
Follow upgrade instructions from here http://forum.xda-developers.com/showthread.php?t=1424997 and sub your firmware file instead of N7000.
es0tericcha0s said:
You'll be able to find your firmware here https://mega.nz/#F!IxJTDDQQ!TTgzxjX8d7EnzemoIj0ogg
4.1.2 was the last official update from Samsung for your device. If you want to update to newer than that, it will have to be done via updating with a custom recovery and custom rom, such as TWRP recovery and CyanogenMod 11 or 12/12.1.
Follow upgrade instructions from here http://forum.xda-developers.com/showthread.php?t=1424997 and sub your firmware file instead of N7000.
Click to expand...
Click to collapse
Thank you es0tericcha0s for this information.
What I'm trying to do right now is updating my SHV-e160s from 4.0.4 to 4.1.2 using Kies v2.6. Unfortunately, I'm getting this error "Failed to run firmware upgrade: unknown error.". Until now, I'm afraid to update my firmware manually as I don't have much knowledge to do that.
1) Download firmware and Odin
2) Open Odin as admin
3) Load firmware in PDA or AP slot depending on which version of Odin used
4) Boot to Download Mode and plug in your phone
5) Once Odin recognizes it ( will show highlighted - COM:xx where "xx" is any number, doesn't matter which ones) hit start
6) Grab a drink and a snack and come back in 10 minutes or so
7) If device bootloops, reset in recovery
Once the files are downloaded, the whole process takes less than 10-12 minutes or so. Everything you need is in the guide I linked to besides the firmware you need, which is in the Mega link. If you need a video guide, there are dozens on YouTube. I find it much easier to use than Kies and once you have it working, then there are not many things you will do that restoring with Odin and a factory reset won't get you out of.
es0tericcha0s said:
1) Download firmware and Odin
2) Open Odin as admin
3) Load firmware in PDA or AP slot depending on which version of Odin used
4) Boot to Download Mode and plug in your phone
5) Once Odin recognizes it ( will show highlighted - COM:xx where "xx" is any number, doesn't matter which ones) hit start
6) Grab a drink and a snack and come back in 10 minutes or so
7) If device bootloops, reset in recovery
Once the files are downloaded, the whole process takes less than 10-12 minutes or so. Everything you need is in the guide I linked to besides the firmware you need, which is in the Mega link. If you need a video guide, there are dozens on YouTube. I find it much easier to use than Kies and once you have it working, then there are not many things you will do that restoring with Odin and a factory reset won't get you out of.
Click to expand...
Click to collapse
Alright, I'll try these steps immediately and will comeback for the result. Thanks again.
es0tericcha0s said:
1) Download firmware and Odin
2) Open Odin as admin
3) Load firmware in PDA or AP slot depending on which version of Odin used
4) Boot to Download Mode and plug in your phone
5) Once Odin recognizes it ( will show highlighted - COM:xx where "xx" is any number, doesn't matter which ones) hit start
6) Grab a drink and a snack and come back in 10 minutes or so
7) If device bootloops, reset in recovery
Once the files are downloaded, the whole process takes less than 10-12 minutes or so. Everything you need is in the guide I linked to besides the firmware you need, which is in the Mega link. If you need a video guide, there are dozens on YouTube. I find it much easier to use than Kies and once you have it working, then there are not many things you will do that restoring with Odin and a factory reset won't get you out of.
Click to expand...
Click to collapse
Hello, sorry I forgot to ask, will this root my device? I'm afraid I might bricked it.
No, this is just the official update. As long as the download is good and you follow those directions, you won't do anything that won't be easily recoverable if it doesn't work right away. Soft bricking is not a big deal and nothing you would do here would cause anything worse unless you unplug the phone in the middle of something important.
---------- Post added at 09:23 AM ---------- Previous post was at 09:20 AM ----------
And because you'll probably ask... It's easy to root. Just download Chainfire's SuperSU zip, put it on your phone's storage and use Odin to install TWRP recovery (just like you do with the whole firmware package) , boot to recovery before it boots to the OS and install the zip. Reboot and enjoy.
es0tericcha0s said:
No, this is just the official update. As long as the download is good and you follow those directions, you won't do anything that won't be easily recoverable if it doesn't work right away. Soft bricking is not a big deal and nothing you would do here would cause anything worse unless you unplug the phone in the middle of something important.
---------- Post added at 09:23 AM ---------- Previous post was at 09:20 AM ----------
And because you'll probably ask... It's easy to root. Just download Chainfire's SuperSU zip, put it on your phone's storage and use Odin to install TWRP recovery (just like you do with the whole firmware package) , boot to recovery before it boots to the OS and install the zip. Reboot and enjoy.
Click to expand...
Click to collapse
Hello again es0tericcha0s, I haven't tried the instructions that you gave me yesterday as I'm still downloading the firmware, last night I encountered an issue after enabling my Bluetooth, something like "NFC Service has stopped." just keeps on popping up. So I turned off the bluetooth then restarted my phone, it went well for a while.
After that, I enabled my 3G Cellular Data to check what was NFC service error is, after a few minutes, I lost my signal, phone turned to No Service, then in Settings -> About Phone, I got an Unknown Baseband.
EDIT
I got No Service since last night up until now.
EDIT Oct. 13, 2015 9:49 AM +08:00 Manila Time
I manage to update my phone from ICS 4.0.4 to JB 4.1.2. But still, my baseband is Unknown and I have no signal.
If it did that before you tried to flash anything...that doesn't sound good. Hard to say without testing it, but kind of sounds like the baseband chip (hardware issue).
es0tericcha0s said:
If it did that before you tried to flash anything...that doesn't sound good. Hard to say without testing it, but kind of sounds like the baseband chip (hardware issue).
Click to expand...
Click to collapse
I also though of that, hopefully not.
When I first got the phone, my gf sent me our pictures via bluetooth , no issues occured. After a while, I noticed that there are so many photos of the previous owner (around 1000+) and mp3s (around 1000+ also). So I connected the phone via usb to my pc and deleted all those pictures and mp3s inside the My Computer -> SHV-E160S -> Phone (Computer\SHV-E160S\Phone). After doing so, I started to encouter some issues, when enabling the bluetooth, the phone hangs and reboots then the error 'NFC service has stopped' keeps on popping up, until it went Unknown Baseband.
Now, the phone keeps on rebooting similar to the symptoms that it gets when baseband version is unknown.
I'm looking for solutions to fix the unknown baseband and saw the Back up and Restore EFS, I just need to root the device to try this fix. Maybe I'll post an update whether if I manage to solve this problem or not, if it didn't fix the issue then maybe the problem is the baseband chip. what a crap!
This is my reference for the EFS Fix
http://techbeasts.com/2014/07/13/fix-samsung-galaxy-unknown-baseband-version-guide/
Thanks!
Rooting will be easy. Just install TWRP with Odin and use the SuperSU zip from Chainfire. Process should take like 5 minutes once everything is downloaded.
es0tericcha0s said:
Rooting will be easy. Just install TWRP with Odin and use the SuperSU zip from Chainfire. Process should take like 5 minutes once everything is downloaded.
Click to expand...
Click to collapse
So I need to install TWRP first before rooting the device? Also I'm planning to use a rooted stock firmware which is 4.1.2, I just don't know the difference between UH24 and MH2, I've read that UH24 is already old and it's better to use a MH2 build and what is the Recovery UH24/MH2?
EDIT:
I forgot, I cannot check my current Baseband since it is still unknown.
EDIT: 12:30PM +8:00
I managed to get my Build#, it is MH2, I'm currently looking for a rooted 4.1.2 MH2 download link.
Way faster and easier to use the method I outlined, but either way should work.
es0tericcha0s said:
Way faster and easier to use the method I outlined, but either way should work.
Click to expand...
Click to collapse
Sorry, I'm really a root virgin here. While following your advise, I'm also currently looking at this guide -> http://forum.xda-developers.com/showthread.php?t=1924535. I'm done downloading Tegrak for MH2, a small problem I encountered here is I don't have a folder named 'sdcard' in my phone, so I created one and copied the 'Kernel' .zip, also I copied it to usbStorage folder.
I'm about to flash the 'Recovery' .tar to my phone. Hoping a success result
Should be fine. Your phone's internal storage is seen by the OS as /sdcard. Doesn't matter where you put the file as long as you remember where it's at so you can navigate to it through recovery to install.
es0tericcha0s said:
Should be fine. Your phone's internal storage is seen by the OS as /sdcard. Doesn't matter where you put the file as long as you remember where it's at so you can navigate to it through recovery to install.
Click to expand...
Click to collapse
Oh crap, I didn't thought of that. Installing 'Kernel' .zip now.
jakeortega said:
Oh crap, I didn't thought of that. Installing 'Kernel' .zip now.
Click to expand...
Click to collapse
Finally! I'm done rooting my phone, though I encountered another issues again. My Menu Button and Back Button does not work.
UPDATE: 4:08PM +8:00GMT
I think I found the problem as to why my Menu button and Back button doesn't work. I'v check my Baseband and it is -> E160SKSJMH1 and my Build # is -> JZO54K.E160SKSJMH2. Am I using a wrong FW as supposed to what I should be using? Which build should I install, the MH1 or the MH2?
Also, the Tegrak Kernel I've used is Build 48 for SHV-E160S MH2. I've also tried factory resetting the phone but the issue still exists.
Thanks!
UPDATE: 4:41PM +8:00GMT
Managed to fixed the issue by updating my Touch Firmware. Cool!

No Version of Bootloader .tar File will Run in Odin {Semi Urgent} Halp Pls

I was simply messing around with my old Verizon GN2, because I need a phone to use in the absence of my htc one M9. I went to flash the "stock" version of the bootloader (the bootloaderbaseline2.tar) before I went in to do any real damage and the phone rejected it. The phone screen read the error message "wrong magic string" and the odin display reported that it dropped out after sboot.bin. Just curious whether you guys and your wisdom would have any insight in the matter? I would really prefer not to have to go out and buy another phone.
Also, woohoo for a first post on the forums.
Cordially,
Nixon
logannixon.la said:
I was simply messing around with my old Verizon GN2, because I need a phone to use in the absence of my htc one M9. I went to flash the "stock" version of the bootloader (the bootloaderbaseline2.tar) before I went in to do any real damage and the phone rejected it. The phone screen read the error message "wrong magic string" and the odin display reported that it dropped out after sboot.bin. Just curious whether you guys and your wisdom would have any insight in the matter? I would really prefer not to have to go out and buy another phone.
Also, woohoo for a first post on the forums.
Cordially,
Nixon
Click to expand...
Click to collapse
Are you flashing the full firmware or just bootloader? What options did you have checked and where (in what slot, PDA?) did you put the file to run it? What version are you on, 4.4.2; 4.3? Have you unlocked it before?
bigmike35 said:
Are you flashing the full firmware or just bootloader? What options did you have checked and where (in what slot, PDA?) did you put the file to run it? What version are you on, 4.4.2; 4.3? Have you unlocked it before?
Click to expand...
Click to collapse
I had this phone rooted before, but it wasn't playing well with what my sister wanted it for. So, I flashed a stock image and it rebooted into its stock form. That was two ish years ago. The bootloader was never unlocked. When I brought it back out to begin tinkering, a lot of guides said to flash the stock bootloader (the bootloaderbaseline2 file) and to repartition it before going ahead with something like CASUAL. Considering my sister used it as a daily driver for quite a while, it was probably on 4.3 or whatever the last update Verizon handed out was. I do remember checking to see whether or not it had any available updates and it said it was completely up to date. When I set it up to repartition and flash the BB2 file, it was in the bootloader slot. The Odin flash then failed at the sboot.bin output and the phone proceeded to slide into the good old "connect to Kies" screen. I tried several attempts to get the BB2 file to stick (putting it in all the slots and trying it without partition and auto reboot), but all were to no avail. I have since flashed multiple firmwares in the PDA slot with only the root66_vzw_stock_system.tar.md5 version completing. However, it now displays the "Device firmware is not from verizon. Please bring it into a Verizon store for help." I know the verizon reps will be useless, so I asked you beautiful people.
The only odin boxes that I played with were the top three.
Also, thanks for responding. I appreciate it.
Nixon
logannixon.la said:
I had this phone rooted before, but it wasn't playing well with what my sister wanted it for. So, I flashed a stock image and it rebooted into its stock form. That was two ish years ago. The bootloader was never unlocked. When I brought it back out to begin tinkering, a lot of guides said to flash the stock bootloader (the bootloaderbaseline2 file) and to repartition it before going ahead with something like CASUAL. Considering my sister used it as a daily driver for quite a while, it was probably on 4.3 or whatever the last update Verizon handed out was. I do remember checking to see whether or not it had any available updates and it said it was completely up to date. When I set it up to repartition and flash the BB2 file, it was in the bootloader slot. The Odin flash then failed at the sboot.bin output and the phone proceeded to slide into the good old "connect to Kies" screen. I tried several attempts to get the BB2 file to stick (putting it in all the slots and trying it without partition and auto reboot), but all were to no avail. I have since flashed multiple firmwares in the PDA slot with only the root66_vzw_stock_system.tar.md5 version completing. However, it now displays the "Device firmware is not from verizon. Please bring it into a Verizon store for help." I know the verizon reps will be useless, so I asked you beautiful people.
The only odin boxes that I played with were the top three.
Also, thanks for responding. I appreciate it.
Nixon
Click to expand...
Click to collapse
So it it on 4.4.2 then since all updates are up to date? If that is the case, you can only root using towel root. You can downgrade to 4.3 or 4.2.1 but you would need to send it in ($75) i believe or try the method here that is posted. If it is still on 4.3 i believe you can flash the 4.2.1 firmware and then run root running casual (disable firewall and antim virus else wont complete). Then find Beanstown thread and download the zip for the updated wifi/bootloader for 4.3 with ND7 radio (zip somewhere as well) to upgrade completely to newest radio/images (so it would be a 4.2.1 or 4.3 stock with complete root and unlocked). Then install TWRP and roms
bigmike35 said:
So it it on 4.4.2 then since all updates are up to date? If that is the case, you can only root using towel root. You can downgrade to 4.3 or 4.2.1 but you would need to send it in ($75) i believe or try the method here that is posted. If it is still on 4.3 i believe you can flash the 4.2.1 firmware and then run root running casual (disable firewall and antim virus else wont complete). Then find Beanstown thread and download the zip for the updated wifi/bootloader for 4.3 with ND7 radio (zip somewhere as well) to upgrade completely to newest radio/images (so it would be a 4.2.1 or 4.3 stock with complete root and unlocked). Then install TWRP and roms
Click to expand...
Click to collapse
So, for the moment, is there any way to get it back to stock? I was trying to go the custom recovery route in the beginning, but I now just need a phone that works. I'm pretty sure it's the bootloader firmware that is preventing the device from booting completely. Thanks for all your help.
Nixon
logannixon.la said:
So, for the moment, is there any way to get it back to stock? I was trying to go the custom recovery route in the beginning, but I now just need a phone that works. I'm pretty sure it's the bootloader firmware that is preventing the device from booting completely. Thanks for all your help.
Nixon
Click to expand...
Click to collapse
You can see if you can flash the full Verizon firmware. Should be able to find it here or on Samsungs website.
bigmike35 said:
You can see if you can flash the full Verizon firmware. Should be able to find it here or on Samsungs website.
Click to expand...
Click to collapse
So the stock Verizon firmware will repair the broken bootloader? I'll give it a go. Thanks for the info.
Just a quick update. I flashed the stock firmware for 4.4.2 and everything went over swimmingly. The phone now boots all the way into the Verizon boot splash screen. It then sits there and will not progress. I've tried wiping cache and factory resetting, but it still hangs on the Verizon splash screen. Any pointers?
Thanks again,
Nixon
Another side update. It's still held up on the Verizon boot splash screen, but the led is now pulsing. *Shrugs in confusion
Nixon
logannixon.la said:
Another side update. It's still held up on the Verizon boot splash screen, but the led is now pulsing. *Shrugs in confusion
Nixon
Click to expand...
Click to collapse
Ya i have had that issue before, but I did what you did is to wipe cache, data, factory and that normal let me get a full boot in.
bigmike35 said:
Ya i have had that issue before, but I did what you did is to wipe cache, data, factory and that normal let me get a full boot in.
Click to expand...
Click to collapse
Yeah, I've tried the factory reset and wipe cache, it still gets caught in the Verizon boot loop. I'm not particularly sure what that else to do. The 4.4.2 stock md5 is the only one that will stick in Odin.
logannixon.la said:
Yeah, I've tried the factory reset and wipe cache, it still gets caught in the Verizon boot loop. I'm not particularly sure what that else to do. The 4.4.2 stock md5 is the only one that will stick in Odin.
Click to expand...
Click to collapse
are you flashing it with the PIT file as well?
bigmike35 said:
are you flashing it with the PIT file as well?
Click to expand...
Click to collapse
I think I tried with and without, but I'll give it a shot.
logannixon.la said:
I think I tried with and without, but I'll give it a shot.
Click to expand...
Click to collapse
Ya put that in the PIT tab and firmware in PDA. When it finished, does it say complete or done (box turns green, near top left?)
Also, maybe try another firmware/version?
bigmike35 said:
Ya put that in the PIT tab and firmware in PDA. When it finished, does it say complete or done (box turns green, near top left?)
Also, maybe try another firmware/version?
Click to expand...
Click to collapse
I tried the pit to no avail. Currently wiping again just for fun. Not sure if it helps, but the system recovery screen reads this

NK1, OB6, OF1 testers wanted for NC4 back-booting trials

So, I cobbled together a (custom-recovery) flashable NC4 stock ROM.
I'm interested to find out whether it is possible to boot it successfully from later bootloader firmware - e.g. NK1, OB6, or OF1
(I'm still on NC4 bl and not planning on upgrading near term. It boots on NC4 bl but that's pretty obvious lol)
[size=+2]Q: Why would this be useful?
A: to provide a means for upgrading bootloader firmware without starting from scratch.[/size]
For instance, there are folks on OB6 firmware that would like to use a custom ROM that will only work on OF1 firmware. They can certainly start from scratch (backup and unload the entire device); an alternative would be to:
- Make a backup of an existing rooted ROM (that more than likely has a custom or modified boot image so is not bootable when the bootloader gets re-locked) using the currently-installed custom recovery (which will also be non-bootable under re-lock).
- Restore a (debloated) pure stock ROM w/ Samsung kernel. Root it with Towelroot (does not touch boot image)
- Flash replacement bootloader only in Odin. Locked bootloader = no custom recovery... but with a rooted stock ROM already in place with an unmodified stock kernel it can be immediately unlocked.
NC4 is easily rooted with Towelroot-v3 "on device". No need for PC drivers, online rooting tools with a separate PC, etc (e.g. as with Yemen rooting methods on OB6, OF1)
This approach in principle saves the need to backup everything up in the /sdcard - but you have to know in advance that the NC4 stock kernel and ROM can successfully be booted with later bootloaders.
So anyway, that's what I'm asking for help testing with - folks that are: (a) unlocked and (b) on NK1, OB6 or OF1 bootloader willing to try flashing a debloated NC4 Stock ROM using their existing custom recovery, and see if it boots, roots, and if root survives a single boot cycle.
Contact me via this thread or PM; I'll provide the flashable NC4 and the Towelroot .apk
.
my n900v came with 5.0 Of1 but i rooted, unlocked BL. installed twrp and flashfired NC4 tar minus recovery
runs smooth.I hate lollipop.lol
only bug is wifi password resets everytime i reboot
im curious as to why i have trouble running certain nc2/nc4 roms..some want to bootloop/freeze
baja,biggins,and objective rom
kernel issue maybe? or BL version
btw. i am rooted via towelroot v3
hotrod85z said:
my n900v came with 5.0 Of1 but i rooted, unlocked BL. installed twrp and flashfired NC4 tar minus recovery
runs smooth.I hate lollipop.lol
Click to expand...
Click to collapse
Thank you for posting that, very useful/helpful information to know.
Does Flashfire understand the Samsung "sparse" image format of the system.img.ext4 file inside the Stock (Odin) .md5 tarfile blob? Or maybe somebody else packaged up a "flashable .zip" of NC4?
hotrod85z said:
only bug is wifi password resets everytime i reboot
Click to expand...
Click to collapse
in /system/build.prop, set ro.securestorage.support=false and reboot. You might also want to set ro.config.tima=0 as well.
I suspect that mixing and matching Samsung kernels with bootloader versions breaks something in the TrustZone, and so secure containers and other sort-of-obscure security functions no longer work as the TZ smells something fishy. I am using a rooted PL1 rom on NC4 bl and it would spontaneously reboot (infrequently) until I made the above changes - it's been rock stable for about 4 days now. Why this works I can't really say - it's a "generation skipping" bootloader and stock rom combination - N* bootloader and P* ROM *
hotrod85z said:
im curious as to why i have trouble running certain nc2/nc4 roms..some want to bootloop/freeze
baja,biggins,and objective rom
kernel issue maybe? or BL version
btw. i am rooted via towelroot v3
Click to expand...
Click to collapse
all of the above or none of the above LOL
There are definitely some mysteries here, and I don't claim to fully understand the interdependence of the TZ (== bootloader firmware), the TIMA and RTKP stuff in the kernel, and the cross-communication between kernel and TZ via the qseecom service daemon (which is in the ROM in /system/bin) much less how the APIs of all these interfaces might have changed between major releases.
You could check those two build.prop settings in those ROMs for starters though. I suspect that if the TZ smells something fishy (e.g. a kernel TIMA to TZ info mismatch), a variety of secure credential services in the TZ stop working. It is possible that "ro.securestorage.support" is a toggle that attempts to use TZ services when it is set to "true", and so anything in the ROM which builds on it breaks because the TZ is refusing to play on an otherwise "stock" ROM variant.
FWIW I got the AryaMod (S7Edge MM port) + phantom kernel running on NC4 bl + OF1 modem for a full 24 hours after I disabled the qseecom service daemon. It ran long enough that I had customized the whole thing as a daily driver with all my apps, verified that all sensors & radios worked, made test calls, etc. Rebooted it and the kernel started getting reset by a "Modem Reset". Even weirder was that despite the use of the OF1 "modem" firmware, the kernel was reporting a bunch of RIL "unknown ioctl's". Strikes me as odd that the whole thing could run that long with so many different things happening, and then the "modem" is unhappy - even though other folks are using the ROM with OF1 bl + OF1 radio/modem firmware. (As if the "modem" isn't really the source of the problem, even though that's what initiates the device reset).
.
i initially tried flashing NC4 full tar via ODIN. but even bl unlocked. i got FAIL. flashfire worked!
very curious as to whether a custom n900v kernel would boot my 4.4.2 custom roms..its either that or the BL isnt compatible with non-touchwiz roms....
most of the kernel/modem/firmware links on here are 404 error dead links.. would be nice to see an up to date sticky. ill flash anything as long as i dont end up in JTAG mode with a brick.lol
ive played with verizon s5 atnt s2,galaxy capitivate,atrix 4g and many other phones
the s2 is still by far the fastest Smoothest phone on cm7..the newer the phones..the newer the OS..the bigger the resourse hogs"ram" im a minimalist...
even after flashing NC4 official full tar..im still showing OF1 baseband under settings
@hotrod85z
FWIW I posted a bunch of recovery-flashable stock ROMs here.
There is also a link in that thread to a complete set of (Odin flashable) modems for NC4, NJ6, NK1, OB6, OF1, and PL1 if that is of interest to you.
Maybe I wasn't paying attention, but I could swear that on at least one occasion or two when I performed an Odin modem flash, it didn't "stick", despite no complaints on the handset screen or in Odin - the next boot showed the (prior) baseband version, not what I flashed. Its a bit of a mystery to me; but for now I've resolved to make sure that after the Odin session is complete, I wait 30 seconds or so, then remove the USB cable, and then pull the battery rather than try to restart the device by holding buttons down. It is possible that those events occurred when I soft-restarted the phone, but I'm not sure. For now I'm just trying to always flash and restart with exactly the same method to avoid different behaviors from creeping in.
PS I have no idea if those ROM flashables are compatible with Flashfire. They might be, but I've never tested it, and as they are not pre-rooted I'm not going to suggest it for fear that somebody with a rooted but locked (bootloader) phone will try using flashfire and then end up with a phone that needs a full Odin re-install. Appearances are that each version of the bootloader restricts the Samsung signing verification to only the matching kernel version - you can't even boot a Signed samsung kernel on a locked phone if it is a different version than the bootloader's version.
Hello all I have a emmc exploit note 3 I'm using here and I wanted to flash different radios for the us carrier note 3's and I first tried to use flash fire to try to update the modem, but even that didn't stick, cause I don't readily have a pc available, I wasn't ballsy enough to flash a different carrier modem, since I checked the odin screen and saw that instead of a bootloader unlock, its in developer mode and I didn't want a brick, so overall my question is, do I need a unlocked bootloader to flash different modems and do I need odin tovdo it or will some sort of mobile odin or something do it? Thanks mates and happy flashing.
Dlind said:
Hello all I have a emmc exploit note 3 I'm using here and I wanted to flash different radios for the us carrier note 3's and I first tried to use flash fire to try to update the modem, but even that didn't stick, cause I don't readily have a pc available, I wasn't ballsy enough to flash a different carrier modem, since I checked the odin screen and saw that instead of a bootloader unlock, its in developer mode and I didn't want a brick, so overall my question is, do I need a unlocked bootloader to flash different modems and do I need odin tovdo it or will some sort of mobile odin or something do it? Thanks mates and happy flashing.
Click to expand...
Click to collapse
Well, your question is way off topic for this thread.
But since nobody is in here anyways, I guess I'll answer the parts that I am able to.
The modems that I posted over in that other thread were meant to be flashed in Odin using a PC. You can use either the AP slot or CP slot. Note that the very first post says - in big bold blue letters "Odin-flashable Modems".
Not flashfire. It never said anything about flashfire.
Is there such a thing as MobileOdin? If there is, I know nothing about it and certainly have never tested anything with it. So I don't know and am not going to speculate.
You said something confusing here:
Dlind said:
I checked the odin screen and saw that instead of a bootloader unlock, its in developer mode
Click to expand...
Click to collapse
If it says "MODE: Developer" you have an unlocked bootloader. Which is exactly the same thing as a Developer Edition phone.
If you were to use a PC with Odin and you flashed a FULL Stock firmware flash, yes it would overwrite the unlocked bootloader and indeed re-lock the phone. If you were able to re-root that (stock) ROM, you could perform the unlocking procedure again to unlock it.
On the other hand, those Odin-flashable modem packages do not contain the bootloader firmware, so if you were to use Odin on a PC to flash just those modem images, your bootloader would not get re-locked - the unlocked bootloader is still there, untouched.
When the carriers issue an OTA update, many times (perhaps most of the time) they contain a modem update (NON-HLOS.bin and modem.bin). So it is obvious that they are able to be flashed **somehow** right on the phone, without using Odin from the PC or an "Odin app" at all.
BUT that happens using a combination of the STOCK recovery and the bootloader itself during the reboot following the actions taken by the STOCK recovery. (My guess is that the recovery simply "stages" it into place, and sets some flags so that the bootloader knows that it is supposed to evaluate the crypto signatures of the file blobs that the recovery put into place and it is actually the bootloader that does the flashing. That's really not a whole lot different than what happens when you transfer files from Odin to the phone - the "Odin/Download" mode is just one of the personalities of the bootloader. (Odin is actually a rather dumb program - it's the bootloader on the phone that gets to decide whether a flash happens. It does that by carefully examining the file blob that gets transferred, e.g. crypto signature checks)
My guess is that you would be able to flash STOCK modem packages from Odin (using a PC) independent of whether the bootloader is locked or unlocked. But as I said: "guess".
I don't have a second phone to test with, so I would have to flash completely back to stock and lock my bootloader to be able to test that hypothesis. That's a big jobs because of all the crap I have to backup and restore to my phone.
Frankly, if you don't have access to a PC, and you really need your device to keep working, I would advise you to stop screwing around with it, simply because you don't have good tools available to fix it if a disaster occurs.
PS. I've never once noticed anything different between various radio firmwares on ANY device I've ever owned.
bftb0 said:
Well, your question is way off topic for this thread.
But since nobody is in here anyways, I guess I'll answer the parts that I am able to.
The modems that I posted over in that other thread were meant to be flashed in Odin using a PC. You can use either the AP slot or CP slot. Note that the very first post says - in big bold blue letters "Odin-flashable Modems".
Not flashfire. It never said anything about flashfire.
Is there such a thing as MobileOdin? If there is, I know nothing about it and certainly have never tested anything with it. So I don't know and am not going to speculate.
You said something confusing here:
If it says "MODE: Developer" you have an unlocked bootloader. Which is exactly the same thing as a Developer Edition phone.
If you were to use a PC with Odin and you flashed a FULL Stock firmware flash, yes it would overwrite the unlocked bootloader and indeed re-lock the phone. If you were able to re-root that (stock) ROM, you could perform the unlocking procedure again to unlock it.
On the other hand, those Odin-flashable modem packages do not contain the bootloader firmware, so if you were to use Odin on a PC to flash just those modem images, your bootloader would not get re-locked - the unlocked bootloader is still there, untouched.
When the carriers issue an OTA update, many times (perhaps most of the time) they contain a modem update (NON-HLOS.bin and modem.bin). So it is obvious that they are able to be flashed **somehow** right on the phone, without using Odin from the PC or an "Odin app" at all.
BUT that happens using a combination of the STOCK recovery and the bootloader itself during the reboot following the actions taken by the STOCK recovery. (My guess is that the recovery simply "stages" it into place, and sets some flags so that the bootloader knows that it is supposed to evaluate the crypto signatures of the file blobs that the recovery put into place and it is actually the bootloader that does the flashing. That's really not a whole lot different than what happens when you transfer files from Odin to the phone - the "Odin/Download" mode is just one of the personalities of the bootloader. (Odin is actually a rather dumb program - it's the bootloader on the phone that gets to decide whether a flash happens. It does that by carefully examining the file blob that gets transferred, e.g. crypto signature checks)
My guess is that you would be able to flash STOCK modem packages from Odin (using a PC) independent of whether the bootloader is locked or unlocked. But as I said: "guess".
I don't have a second phone to test with, so I would have to flash completely back to stock and lock my bootloader to be able to test that hypothesis. That's a big jobs because of all the crap I have to backup and restore to my phone.
Frankly, if you don't have access to a PC, and you really need your device to keep working, I would advise you to stop screwing around with it, simply because you don't have good tools available to fix it if a disaster occurs.
PS. I've never once noticed anything different between various radio firmwares on ANY device I've ever owned.
Click to expand...
Click to collapse
Thanks SOOOOOO MUCH for your input I kinda had a feeling that the idea was risky at first and I don't know a whole lot about odin and I wish Samsung could have created something much easier to use, but thanks for answering the wayyyyy off topic question, I'm gonna smash that thanks button, I'm also going to take the advise on not cross flashing different modems, its just to risky. You answered all my questions so thanks, Also I want to say thank you for your continued work on this phone is by normal terms "old" now but in reality its still an amazing phone with the right custom software, and happy flashing!

Categories

Resources