HELP!!! My lenovo p780 dead, does not boot. - Lenovo P780

My Lenovo P780 does not boot any more. Push power button, nothing happened. Connect by usb cable, only red led works. What can I do?
Bought from china, chinaunicomm customed phone. I tried flash, but can not connect it to computer.

bonbonbillo said:
My Lenovo P780 does not boot any more. Push power button, nothing happened. Connect by usb cable, only red led works. What can I do?
Bought from china, chinaunicomm customed phone. I tried flash, but can not connect it to computer.
Click to expand...
Click to collapse
Did u installed p780 drivers into your Pc ?
u must if u want to flash it .

bonbonbillo said:
My Lenovo P780 does not boot any more. Push power button, nothing happened. Connect by usb cable, only red led works. What can I do?
Bought from china, chinaunicomm customed phone. I tried flash, but can not connect it to computer.
Click to expand...
Click to collapse
It's easy to fix Just follow my steps. :fingers-crossed:
1.Prepare the rom which was running ok before,for example, for me it was @satanduck 's prerooted TWRP S124 rom.
2.Open the SP flash tool.
3.Load the scatter file from the rom which worked ok for you.
4.Tick the box that says 'DA DL All With Check Sum'
5.Hit Firmware Upgrade
Now is the hardest step
1.Open the cover of your phone.
2.Look for the red reset button which was close to SD card and press it a few times.
3.Connect USB cable to your phone and firmware upgrade should start and wait for the green circle! :good::laugh:
Best luck :good:

bonbonbillo said:
My Lenovo P780 does not boot any more. Push power button, nothing happened. Connect by usb cable, only red led works. What can I do?
Bought from china, chinaunicomm customed phone. I tried flash, but can not connect it to computer.
Click to expand...
Click to collapse
What have you done to your phone? Did you install or flash something? Did you change something in system ?
Sent from my Lenovo P780 with TWRP 2.7.1.1

glixbourkt said:
Did u installed p780 drivers into your Pc ?
u must if u want to flash it .
Click to expand...
Click to collapse
Yes, I installed mtk usb drivers. but I´m not sure if it´s ok o no. Because I have to connect the battery and push volume+up button to make it connected. and it´ll disappear immediately in device management window.

stympy said:
What have you done to your phone? Did you install or flash something? Did you change something in system ?
Sent from my Lenovo P780 with TWRP 2.7.1.1
Click to expand...
Click to collapse
Just tried to root, but not completed. and then tried flash to rescue, but not yet get it connected to computer.

tngultimate said:
It's easy to fix Just follow my steps. :fingers-crossed:
1.Prepare the rom which was running ok before,for example, for me it was @satanduck 's prerooted TWRP S124 rom.
2.Open the SP flash tool.
3.Load the scatter file from the rom which worked ok for you.
4.Tick the box that says 'DA DL All With Check Sum'
5.Hit Firmware Upgrade
Now is the hardest step
1.Open the cover of your phone.
2.Look for the red reset button which was close to SD card and press it a few times.
3.Connect USB cable to your phone and firmware upgrade should start and wait for the green circle! :good::laugh:
Best luck :good:
Click to expand...
Click to collapse
I can not get it connected to computer. Only when I push volume+up button,and connect the usb cable, it can be found. But then it disappears immediately in device management window. can not continue to flash.

Hi,
Please verify that you have a correct production date. I got a P780 after 0314. please try the solution on this post
http://forum.xda-developers.com/showpost.php?p=52665841&postcount=16
If this resolves your problem, that keep that preloader. With that you can almost flash every rom that there is with the flashtool.
(i'm very satisfied with the latest rom on needrom Vibeui2.0 (the rom page also offers the new preloader )
Greetz,
btw to try to flash with the new preloader set up the flashtool, push the red button on the back of your phone, connect the phone an release the button. If all the drivers are correct your phone will be flashed. ( this new batch phones gave me a heart attack also , mine wasn't even 12 hours active before i softbricked it )

Re-Mi said:
Hi,
Please verify that you have a correct production date. I got a P780 after 0314. please try the solution on this post
http://forum.xda-developers.com/showpost.php?p=52665841&postcount=16
If this resolves your problem, that keep that preloader. With that you can almost flash every rom that there is with the flashtool.
(i'm very satisfied with the latest rom on needrom Vibeui2.0 (the rom page also offers the new preloader )
Greetz,
btw to try to flash with the new preloader set up the flashtool, push the red button on the back of your phone, connect the phone an release the button. If all the drivers are correct your phone will be flashed. ( this new batch phones gave me a heart attack also , mine wasn't even 12 hours active before i softbricked it )
Click to expand...
Click to collapse
When I push the red button, phone can not be recognized by computer. Only I press the volume-up button, it can be recognized by computer.
I start the flash, then push volume-up button to make it connected, but then got BROM error. I attach the screen picture.

bonbonbillo said:
When I push the red button, phone can not be recognized by computer. Only I press the volume-up button, it can be recognized by computer.
I start the flash, then push volume-up button to make it connected, but then got BROM error. I attach the screen picture.
Click to expand...
Click to collapse
You must have this FlashTool - SP_Flash_Tool_v3.1304.0.119. Not Optional.
Check if your phone is produced in 2014. If it is you must use another preloader.

stympy said:
You must have this FlashTool - SP_Flash_Tool_v3.1304.0.119. Not Optional.
Check if your phone is produced in 2014. If it is you must use another preloader.
Click to expand...
Click to collapse
Yes, I have the FlashTool v3.1304.0.119. (picture attached)
My phone is produced before 2014.

bonbonbillo said:
Yes, I have the FlashToll v3.1304.0.119. (picture attached)
My phone is produced before 2014.
Click to expand...
Click to collapse
Try to flash with this Flah Tool, and tell me if gives you new errors.

stympy said:
Try to flash with this Flah Tool, and tell me if gives you new errors.
Click to expand...
Click to collapse
Which one? Have you attached any file? I don't see it. Tks.

bonbonbillo said:
Which one? Have you attached any file? I don't see it. Tks.
Click to expand...
Click to collapse
I have attached now.
Sent from my Lenovo P780 with TWRP 2.7.1.1

stympy said:
I have attached now.
Sent from my Lenovo P780 with TWRP 2.7.1.1
Click to expand...
Click to collapse
Same error, when the red color goes to the end, after around 3 minutes, says brom error....4001

bonbonbillo said:
Same error, when the red color goes to the end, after around 3 minutes, says brom error....4001
Click to expand...
Click to collapse
I think you should go to a service store. Thats my opinion.

stympy said:
I think you should go to a service store. Thats my opinion.
Click to expand...
Click to collapse
Trying to find solution here, not to solve only with money in mobile store. Anybody else help?

bonbonbillo said:
Trying to find solution here, not to solve only with money in mobile store. Anybody else help?
Click to expand...
Click to collapse
I thought you have warranty on your phone !
So... this error appear when you try to flash wrong ROM or you have wrong drivers installed. Try to remove drivers you have installed and try to reinstall another driver.
Orrrr.. your phone could be a clone. Just an ideea ...
Could you tell us more about your phone... maybe pictures taken from battery or box who came with ?

Related

[Q] My phone has been bricked! :`(

Hello!
I think my MMX Canvas HD A116 has been soft bricked. :crying:
I'd installed DOGE http://forum.xda-developers.com/showthread.php?t=2663763 ROM, and it was working fine. After that I tried to get backup using Nandroid Manager but it was failed. So, I restarted phone in CWM Recovery mode and tried to backup data from there.
But after that, my phone went dead.
Screen starts for few seconds but it is not showing boot logo and even I'm not able to go into recovery mode also!
My PC or SP Flash Tool is also not recognizing phone.
Will USB Jig work for MMX phones? Is there any hope?!
Please help!
try to reinstall the drivers.. and then connect your device through sptools.
kalpesh_36 said:
try to reinstall the drivers.. and then connect your device through sptools.
Click to expand...
Click to collapse
I tried that.
Still not working! :crying:
try this
1. Turn off the phone by
removing battery.
2. Press and hold the Power button along with both the
‘Volume +’ and ‘Volume -’ buttons until the screen
displays two options.(volume keys first then power key .
after 5-10 seconds holding, Then 2 option will appear)
3. Press the ‘Volume +’ button to enter Recovery Mode.
wipe dalvik, data, cache partion. install MIUI or pure xperia
z2(my choice only, you can try any stable rom) from your
memory card.
shivrajsingh said:
try this
1. Turn off the phone by
removing battery.
2. Press and hold the Power button along with both the
‘Volume +’ and ‘Volume -’ buttons until the screen
displays two options.(volume keys first then power key .
after 5-10 seconds holding, Then 2 option will appear)
3. Press the ‘Volume +’ button to enter Recovery Mode.
wipe dalvik, data, cache partion. install MIUI or pure xperia
z2(my choice only, you can try any stable rom) from your
memory card.
Click to expand...
Click to collapse
Thank you Shivraj for replying.
But as I said in earlier post, my phone is not going into recovery mode. As I press "Volume +" button, it goes off. I wish somehow I can at least boot my phone into recovery mode!
Have anyone tried USB jig for Micromax phones?
aryankirtan said:
Thank you Shivraj for replying.
But as I said in earlier post, my phone is not going into recovery mode. As I press "Volume +" button, it goes off. I wish somehow I can at least boot my phone into recovery mode!
Have anyone tried USB jig for Micromax phones?
Click to expand...
Click to collapse
i guess usb jig only works for Samsung phones..but since u r saying that the device does power on for a second...mayb its not completely bricked...try installing the correct drivers..see if that works?
edwardpage said:
i guess usb jig only works for Samsung phones..but since u r saying that the device does power on for a second...mayb its not completely bricked...try installing the correct drivers..see if that works?
Click to expand...
Click to collapse
That right. Even if USB Jig works on MTk, it will also result in rebooting after 2-3 seconds which you are getting after pressing volume + button. You can only install correct MTK drivers and then install stock rom.
Download Flash Tool , Stock ROM AND USB Driver From Above LINK
NOW Create Folder IN Desktop Give It Name "FLASH"
Copy All Downloaded File In Recently Created Folder "FLASH"
Extract 'SP_Flash_Tool_v3.1304.0.119.rar' AND Also Extract Stock ROM File
NOW Open SP Flash Tools Folder AND Double Click ON "Flashtool.exe"
In Flashtool..Click On SCATTER-LOADING(FOUND IN RIGHT-SIDE) AND Select SCATTER File From STOCK ROM'S Folder
Flashtool Automatic Select All IMGs AND FILEs
NOW Completely Turn Off Your Phone
In Flashtool..Click On "DOWNLOAD" Button
Install USB Driver AND Connect Your Device To Computer
If Everything Is Right Then Process Will Start...Wait Till All Progress Completion
After All Process "GREEN CIRCLE" Appear In Center..
DISCONNECT PHONE AND POWER ON...THAT'S ALL
the correct drivers for mediatek is attached below.
Also, the process after "In Flashtool..Click On "DOWNLOAD" Button" , should be:
1. Open device manager
2. Connect your phone to PC through data cable.
3. New device will appear in device manager for 5-10 seconds only.
4. Quickly right click on newly appeared device and selected update driver.
5. Select drivers from downloaded and extracted attachment.
6. It will successfully install driver.
7. Remove data cable from phone and again insert it in phone.
8. SP tools will recognize it and automatically start flashing since you have already pressed download button earlier.
9. Flashing will complete in 3-4 minutes.
Thank you so much! Finally unbricked my MMX A116
shivrajsingh said:
That right. Even if USB Jig works on MTk, it will also result in rebooting after 2-3 seconds which you are getting after pressing volume + button. You can only install correct MTK drivers and then install stock rom.
Download Flash Tool , Stock ROM AND USB Driver From Above LINK
NOW Create Folder IN Desktop Give It Name "FLASH"
Copy All Downloaded File In Recently Created Folder "FLASH"
Extract 'SP_Flash_Tool_v3.1304.0.119.rar' AND Also Extract Stock ROM File
NOW Open SP Flash Tools Folder AND Double Click ON "Flashtool.exe"
In Flashtool.. Click On SCATTER-LOADING(FOUND IN RIGHT-SIDE) AND Select SCATTER File From STOCK ROM'S Folder
Flashtool Automatic Select All IMGs AND FILEs
NOW Completely Turn Off Your Phone
In Flashtool..Click On "DOWNLOAD" Button
Install USB Driver AND Connect Your Device To Computer
If Everything Is Right Then Process Will Start...Wait Till All Progress Completion
After All Process "GREEN CIRCLE" Appear In Center..
DISCONNECT PHONE AND POWER ON...THAT'S ALL
the correct drivers for mediatek is attached below.
Also, the process after "In Flashtool..Click On "DOWNLOAD" Button" , should be:
1. Open device manager
2. Connect your phone to PC through data cable.
3. New device will appear in device manager for 5-10 seconds only.
4. Quickly right click on newly appeared device and selected update driver.
5. Select drivers from downloaded and extracted attachment.
6. It will successfully install driver.
7. Remove data cable from phone and again insert it in phone.
8. SP tools will recognize it and automatically start flashing since you have already pressed download button earlier.
9. Flashing will complete in 3-4 minutes.
Click to expand...
Click to collapse
Thank you soooo much man. You saved my day... :good:
This drivers worked perfectly and with this method, I finally UNBRICKED my Micromax A116 handset.
Use this drivers for using SP Flash tool with MMX A116.
Perfect!
Thank you Shivraj Singh... :good:
aryankirtan said:
Thank you soooo much man. You saved my day... :good:
This drivers worked perfectly and with this method, I finally UNBRICKED my Micromax A116 handset.
Use this drivers for using SP Flash tool with MMX A116.
Perfect!
Thank you Shivraj Singh... :good:
Click to expand...
Click to collapse
Most welcome
shivrajsingh said:
That right. Even if USB Jig works on MTk, it will also result in rebooting after 2-3 seconds which you are getting after pressing volume + button. You can only install correct MTK drivers and then install stock rom.
Download Flash Tool , Stock ROM AND USB Driver From Above LINK
NOW Create Folder IN Desktop Give It Name "FLASH"
Copy All Downloaded File In Recently Created Folder "FLASH"
Extract 'SP_Flash_Tool_v3.1304.0.119.rar' AND Also Extract Stock ROM File
NOW Open SP Flash Tools Folder AND Double Click ON "Flashtool.exe"
In Flashtool..Click On SCATTER-LOADING(FOUND IN RIGHT-SIDE) AND Select SCATTER File From STOCK ROM'S Folder
Flashtool Automatic Select All IMGs AND FILEs
NOW Completely Turn Off Your Phone
In Flashtool..Click On "DOWNLOAD" Button
Install USB Driver AND Connect Your Device To Computer
If Everything Is Right Then Process Will Start...Wait Till All Progress Completion
After All Process "GREEN CIRCLE" Appear In Center..
DISCONNECT PHONE AND POWER ON...THAT'S ALL
the correct drivers for mediatek is attached below.
Also, the process after "In Flashtool..Click On "DOWNLOAD" Button" , should be:
1. Open device manager
2. Connect your phone to PC through data cable.
3. New device will appear in device manager for 5-10 seconds only.
4. Quickly right click on newly appeared device and selected update driver.
5. Select drivers from downloaded and extracted attachment.
6. It will successfully install driver.
7. Remove data cable from phone and again insert it in phone.
8. SP tools will recognize it and automatically start flashing since you have already pressed download button earlier.
9. Flashing will complete in 3-4 minutes.
Click to expand...
Click to collapse
Hello sir pls. Help me. I too want to flash the v5 of stock ROM but i the driver you have suggested below contains nothing.pls help how to proceed ahead.
alex279 said:
Hello sir pls. Help me. I too want to flash the v5 of stock ROM but i the driver you have suggested below contains nothing.pls help how to proceed ahead.
Click to expand...
Click to collapse
They contain drivers only. SP tools and stock rom needs to be downloaded separately.
need help for drivers
shivrajsingh said:
They contain drivers only. SP tools and stock rom needs to be downloaded separately.
Click to expand...
Click to collapse
very much thankful for the reply.... i am having the other 2 but facing problem with only the drivers, going through sp tools...scatter loading...download....no detection of my device... this might be due to drivers. i found nothing in your 11kb drivers. pls suggest me how i can download the correct drivers. pls. if possible elaborate it stepwise(as i m doing it for the first time/newbie)......hope a quick reply from your side
alex279 said:
very much thankful for the reply.... i am having the other 2 but facing problem with only the drivers, going through sp tools...scatter loading...download....no detection of my device... this might be due to drivers. i found nothing in your 11kb drivers. pls suggest me how i can download the correct drivers. pls. if possible elaborate it stepwise(as i m doing it for the first time/newbie)......hope a quick reply from your side
Click to expand...
Click to collapse
Which windows version, u r using??
.....!!!!!
shivrajsingh said:
Which windows version, u r using??
Click to expand...
Click to collapse
Using windows 8 - 64Bit
alex279 said:
Using windows 8 - 64Bit
Click to expand...
Click to collapse
First disable driver signing (Windows 8 users Only)
use this link for tutorial.....
https://learn.sparkfun.com/tutorial...abling-signed-driver-enforcement-on-windows-8
Now extract the mtk universal driver attachment.
1. Open device manager
2. Connect your phone to PC through data cable.
3. New device will appear in device manager for 5-10 seconds only.
4. Quickly right click on newly appeared device and selected update driver.
5. Select drivers from downloaded and extracted attachment.(right click on new appeared device -> browse my computer for drivers-> browse windows 7 drivers i.e. usb2ser_Win764 in extracted folder)
6. It will successfully install driver.
7. Remove data cable from phone and again insert it in phone.
8. SP tools will recognize it and automatically start flashing since you have already pressed download button earlier.
9. Flashing will complete in 3-4 minutes.
Hello many thnx to you for this useful info. Now i have flashed the device successfully.... Pls. if you can help me to swap the phone storage with the external sd card then it would be great help for me. Actually i have tried to do so but some how i bricked the device & that is why i have to flash.... Pls. Sir give me details guide on how to swap memory on canvas HD A116
Sent from my Micromax A116i using XDA Premium 4 mobile app
alex279 said:
Hello many thnx to you for this useful info. Now i have flashed the device successfully.... Pls. if you can help me to swap the phone storage with the external sd card then it would be great help for me. Actually i have tried to do so but some how i bricked the device & that is why i have to flash.... Pls. Sir give me details guide on how to swap memory on canvas HD A116
Sent from my Micromax A116i using XDA Premium 4 mobile app
Click to expand...
Click to collapse
Hello friend,
Try this way: http://forum.xda-developers.com/showthread.php?t=2346389
As it works on MediaTek devices and MMX A116 is one of this.
pls suggest me how i can download the correct drivers.
aryankirtan said:
Hello!
I think my MMX Canvas HD A116 has been soft bricked. :crying:
I'd installed DOGE http://forum.xda-developers.com/showthread.php?t=2663763 ROM, and it was working fine. After that I tried to get backup using Nandroid Manager but it was failed. So, I restarted phone in CWM Recovery mode and tried to backup data from there.
But after that, my phone went dead.
Screen starts for few seconds but it is not showing boot logo and even I'm not able to go into recovery mode also!
My PC or SP Flash Tool is also not recognizing phone.
Will USB Jig work for MMX phones? Is there any hope?!
Please help!
Click to expand...
Click to collapse
It had to me once, when I was going to flash the stock rom from SP Flash tools. I think there was some drivers problem, and the process stopped in between, and when i tried to turn the phone on, it only emitted some light and would stay that until the battery would drain. After a few days, it went dead, no response. This was the time I realized that I had to give it to a service center. Unfortunately, the service was awfully bad, and my phone came repaired back after 3 MONTHS! So, I recommend, that you hand it over to a non-micromax service center (as your warranty is now void), and try your luck! All the best!
P.S. My CHD is working awesome now, installed MiUi
[email protected] said:
pls suggest me how i can download the correct drivers.
Click to expand...
Click to collapse
download Mt65xx vcom drivers then see the video below
---------- Post added at 12:54 PM ---------- Previous post was at 12:06 PM ----------
aryankirtan said:
Thank you Shivraj for replying.
But as I said in earlier post, my phone is not going into recovery mode. As I press "Volume +" button, it goes off. I wish somehow I can at least boot my phone into recovery mode!
Have anyone tried USB jig for Micromax phones?
Click to expand...
Click to collapse
just flash the stock backup using SP flash tool

[Q] Help!!!!!!!!

:crying: Guys , my SP Flash Tool keep stucking at "100%RedBar" and "0%" . I can't flash anything... :crying: Help me pls...
tngultimate said:
:crying: Guys , my SP Flash Tool keep stucking at "100%RedBar" and "0%" . I can't flash anything... :crying: Help me pls...
Click to expand...
Click to collapse
What are tryng to flash?
Sent from my Lenovo P780
stympy said:
What are tryng to flash?
Sent from my Lenovo P780
Click to expand...
Click to collapse
Lenovo P780 stock rom s124
tngultimate said:
Lenovo P780 stock rom s124
Click to expand...
Click to collapse
Use spflash tool 5 not 3. In spflash tool 5 select firmware upgrade not download.
Try and tel me if works.
Sent from my Lenovo P780
stympy said:
Use spflash tool 5 not 3. In spflash tool 5 select firmware upgrade not download.
Try and tel me if works.
Sent from my Lenovo P780
Click to expand...
Click to collapse
It keep saying "Unrecognized Rom" detected
tngultimate said:
It keep saying "Unrecognized Rom" detected
Click to expand...
Click to collapse
Soo.. Sp flash tool 3 is telling you the same thing ?
Sent from my Lenovo P780
stympy said:
Soo.. Sp flash tool 3 is telling you the same thing ?
Sent from my Lenovo P780
Click to expand...
Click to collapse
sp flash tool 3 just stuck at red bar or 0 %...
tngultimate said:
sp flash tool 3 just stuck at red bar or 0 %...
Click to expand...
Click to collapse
Use spflash tool 3 open the back of your phone and press the red button on your right for 20 secconds after yo pressed firmware upgrade button abd pluged your cable.
Sent from my Lenovo P780
stympy said:
Use spflash tool 3 open the back of your phone and press the red button on your right for 20 secconds after yo pressed firmware upgrade button abd pluged your cable.
Sent from my Lenovo P780
Click to expand...
Click to collapse
Also stuck at 0% ... but the time keep increasing . After 40 seconds , it appear a message says
BROM ERROR : S_FT_READBACK_FAIL (4009)
tngultimate said:
Also stuck at 0% ... but the time keep increasing . After 40 seconds , it appear a message says
BROM ERROR : S_FT_READBACK_FAIL (4009)
Click to expand...
Click to collapse
Hi. Lets try this: since "Firmware Upgrade" or "Download" option dont work, first "Format---->Auto Format Whole NAND flash", then flash ROM using "Download" option with "DA/DL all" selected !!!
Tell me if works.
stympy said:
Hi. Lets try this: since "Firmware Upgrade" or "Download" option dont work, first "Format---->Auto Format Whole NAND flash", then flash ROM using "Download" option with "DA/DL all" selected !!!
Tell me if works.
Click to expand...
Click to collapse
My phone now doesn't detected by my computer... It can connect to computer yesterday... Now my phone just charging when connect to computer... Save me please :crying::crying:
tngultimate said:
My phone now doesn't detected by my computer... It can connect to computer yesterday... Now my phone just charging when connect to computer... Save me please :crying::crying:
Click to expand...
Click to collapse
Follow this steps:
1. Go to My computer>Right Click> Properties> Device manager>Universal Serial Bus Controller
2. Now plug the cable in your device.
3. Tell me what appears there.
stympy said:
Follow this steps:
1. Go to My computer>Right Click> Properties> Device manager>Universal Serial Bus Controller
2. Now plug the cable in your device.
3. Tell me what appears there.
Click to expand...
Click to collapse
I have the exact same issue. Flashing stock S124 after (rooted) S223 with SpTools messes something up.
I managed to do a TWRP restore to go back to S221 but I can't use SpTools anymore.
I get the same SpTools error message. Only after pressing the red reset button my phone will then come back to life.
stympy said:
Follow this steps:
1. Go to My computer>Right Click> Properties> Device manager>Universal Serial Bus Controller
2. Now plug the cable in your device.
3. Tell me what appears there.
Click to expand...
Click to collapse
Nothing happen...
londondutch said:
I have the exact same issue. Flashing stock S124 after (rooted) S223 with SpTools messes something up.
I managed to do a TWRP restore to go back to S221 but I can't use SpTools anymore.
I get the same SpTools error message. Only after pressing the red reset button my phone will then come back to life.
Click to expand...
Click to collapse
Your preloader seems to be messet up. I have one problem the same like yours yesterday. It took like 4 hours to solve the problem. The problem was like this:
The computer was not recognizing the phone when the phone was powered off. Sooo.. what i did: i opened device manager in the computer, then i attached the phone. Something new has appeared in the device manager for a seccond. I clicked fast on it. A small window hass appeared. From this step i was safe. I just updated the driver and that wass it. I could flash the ROM i wanted.
Hope this helps you.
---------- Post added at 03:58 PM ---------- Previous post was at 03:57 PM ----------
tngultimate said:
My phone now doesn't detected by my computer... It can connect to computer yesterday... Now my phone just charging when connect to computer... Save me please :crying::crying:
Click to expand...
Click to collapse
Your preloader seems to be messet up. I have one problem the same like yours yesterday. It took like 4 hours to solve the problem. The problem was like this:
The computer was not recognizing the phone when the phone was powered off. Sooo.. what i did: i opened device manager in the computer, then i attached the phone. Something new has appeared in the device manager for a seccond. I clicked fast on it. A small window hass appeared. From this step i was safe. I just updated the driver and that wass it. I could flash the ROM i wanted.
Hope this helps you.
stympy said:
Your preloader seems to be messet up. I have one problem the same like yours yesterday. It took like 4 hours to solve the problem. The problem was like this:
The computer was not recognizing the phone when the phone was powered off. Sooo.. what i did: i opened device manager in the computer, then i attached the phone. Something new has appeared in the device manager for a seccond. I clicked fast on it. A small window hass appeared. From this step i was safe. I just updated the driver and that wass it. I could flash the ROM i wanted.
Hope this helps you.
---------- Post added at 03:58 PM ---------- Previous post was at 03:57 PM ----------
Your preloader seems to be messet up. I have one problem the same like yours yesterday. It took like 4 hours to solve the problem. The problem was like this:
The computer was not recognizing the phone when the phone was powered off. Sooo.. what i did: i opened device manager in the computer, then i attached the phone. Something new has appeared in the device manager for a seccond. I clicked fast on it. A small window hass appeared. From this step i was safe. I just updated the driver and that wass it. I could flash the ROM i wanted.
Hope this helps you.
Click to expand...
Click to collapse
Thanks for your explanation, you seem to be the absolute guru on this site for this device! I think you are right about the preloader being messed up. I tried to install the USB driver (again) for the new device that the computer now sees. It is listed in the device manager as "Unknown Device" under USB controllers. I can't seem to force it to accept new USB drivers for it (Lenovo drivers). It keeps saying that the driver is not compatible with the device. I use Win 7 64bit, could that have something to do with it? Also is it possible to flash a new preloader using TWRP? If I press the reset button on my phone it reboots fine (rooted S221) and I have TWRP installed.
londondutch said:
Thanks for your explanation, you seem to be the absolute guru on this site for this device! I think you are right about the preloader being messed up. I tried to install the USB driver (again) for the new device that the computer now sees. It is listed in the device manager as "Unknown Device" under USB controllers. I can't seem to force it to accept new USB drivers for it (Lenovo drivers). It keeps saying that the driver is not compatible with the device. I use Win 7 64bit, could that have something to do with it? Also is it possible to flash a new preloader using TWRP? If I press the reset button on my phone it reboots fine (rooted S221) and I have TWRP installed.
Click to expand...
Click to collapse
Here are the drivers i use! Hope this will help you!
Soo.. i never tried to flash preloader from TWRP. Thats an ideea, but you have to do a full backup of your phone... i think...
When i have preloader problems i flash again the whole ROM. I think is safer, better... and wize.
stympy said:
Here are the drivers i use! Hope this will help you!
Soo.. i never tried to flash preloader from TWRP. Thats an ideea, but you have to do a full backup of your phone... i think...
When i have preloader problems i flash again the whole ROM. I think is safer, better... and wize.
Click to expand...
Click to collapse
Thanks for the drivers, I am still struggling to make this "Unknown Device" accept other drivers. What was your unrecognised phone called in Device Manager? Was it also "Unknown Device" in the USB section?
londondutch said:
Thanks for the drivers, I am still struggling to make this "Unknown Device" accept other drivers. What was your unrecognised phone called in Device Manager? Was it also "Unknown Device" in the USB section?
Click to expand...
Click to collapse
Hi. The think was someting like this:
First i installed the .exe file. Reboot PC.
2. I have plugged the phone to the PC and new hardware wizard has appeared.
3. Now i have powered of the phone.
4. Again i have plugged the phone this time powered off.
5. At this time in Device Manager appeared for a second or two not in USB area something with.. MTK65...
6. Click very fast on it because that will desapear very fast.
7. After you clicked on it all you have to do is update driver, and voila you have drivers installed and now all you have to do is to flash you ROM.
Hope this will help you.
Good luck.
Sent from my Lenovo P780
stympy said:
Hi. The think was someting like this:
First i installed the .exe file. Reboot PC.
2. I have plugged the phone to the PC and new hardware wizard has appeared.
3. Now i have powered of the phone.
4. Again i have plugged the phone this time powered off.
5. At this time in Device Manager appeared for a second or two not in USB area something with.. MTK65...
6. Click very fast on it because that will desapear very fast.
7. After you clicked on it all you have to do is update driver, and voila you have drivers installed and now all you have to do is to flash you ROM.
Hope this will help you.
Good luck.
Sent from my Lenovo P780
Click to expand...
Click to collapse
Thanks !!! ^^ Finally I won !!! You are like the proffesion in P780 !!! Stympy , another thing i want to ask you , how to root S223 the rom that you give ? I saw there was an alternative scatter in your S223 .

[Q] MMX A116 Hard Brick.

Hi Guys,
My sister's MMX A116 is totally bricked and not even able to turn it on. Earlier It was stuck in bootloop and she gave it to some mobile repairing shop and they hard bricked it . I can't even boot to recovery. Is there any chance of unbricking it? If yes, please tell how.
MrJukeHardbane said:
Hi Guys,
My sister's MMX A116 is totally bricked and not even able to turn it on. Earlier It was stuck in bootloop and she gave it to some mobile repairing shop and they hard bricked it . I can't even boot to recovery. Is there any chance of unbricking it? If yes, please tell how.
Click to expand...
Click to collapse
MrJukeHardbane,
First of all you need to download A116 Stock ROM, Drivers and SP Flash Tools by googling.
Then Remove your battery of the phone and SIM cards as well as Memory card,
Then install A116 Drivers in your PC then open SP flash tools window by double clicking on Flash_Tools.exe
the windows of SP Flash tool will open then click on Scatter Loading and search for the A116 Stock ROM you downloaded and extracted and find MT6589_Android_scatter_emmc file and open it
find the Download button on the upper side of window and click on it
Then connect your phone to PC with the data cable and try pressing volume up button and power butter simultaneously 3 to 4 times them you can see at the base of the window your phone will get detected and connected with the port and rest process will be done automatically wail till you see the green circle on the screen.
Once you find green circle remove your device and try to start after fixing Battery and Sim card and memory card.
If your phone is soft bricked... It will definitely boot up and it takes about 10 minutes at first boot up so keep patience..
HIT THANKS IF I HELPED YOU :good:
ndbhatt2006 said:
MrJukeHardbane,
First of all you need to download A116 Stock ROM, Drivers and SP Flash Tools by googling.
Then Remove your battery of the phone and SIM cards as well as Memory card,
Then install A116 Drivers in your PC then open SP flash tools window by double clicking on Flash_Tools.exe
the windows of SP Flash tool will open then click on Scatter Loading and search for the A116 Stock ROM you downloaded and extracted and find MT6589_Android_scatter_emmc file and open it
find the Download button on the upper side of window and click on it
Then connect your phone to PC with the data cable and try pressing volume up button and power butter simultaneously 3 to 4 times them you can see at the base of the window your phone will get detected and connected with the port and rest process will be done automatically wail till you see the green circle on the screen.
Once you find green circle remove your device and try to start after fixing Battery and Sim card and memory card.
If your phone is soft bricked... It will definitely boot up and it takes about 10 minutes at first boot up so keep patience..
HIT THANKS IF I HELPED YOU :good:
Click to expand...
Click to collapse
When I click the download button and connect USB, nothing is happening. It just get stuck to 0%
MrJukeHardbane said:
When I click the download button and connect USB, nothing is happening. It just get stuck to 0%
Click to expand...
Click to collapse
check if your phone connects with the usb port or not?
because this can happen if your phone drivers are not installed or wrong drivers installed
visit micromax website and download drivers for a116 from there first remove old one and install new one then try again.
HIT THANKS IF I HELPED YOU......
ndbhatt2006 said:
check if your phone connects with the usb port or not?
because this can happen if your phone drivers are not installed or wrong drivers installed
visit micromax website and download drivers for a116 from there first remove old one and install new one then try again.
HIT THANKS IF I HELPED YOU......
Click to expand...
Click to collapse
Phone is now detecting but i am not able to flash from SP tools, getting Error : BROM ERROR : S_DL_PMT_ERR_NO_SPACE (5069). Haven't found any fix for this error yet.
MrJukeHardbane said:
Phone is now detecting but i am not able to flash from SP tools, getting Error : BROM ERROR : S_DL_PMT_ERR_NO_SPACE (5069). Haven't found any fix for this error yet.
Click to expand...
Click to collapse
If your EMMC chip or RAM is damaged by Mobile repairing person then you will be helpless...
but if it is ok then once again try, this time in SP Flash tool select option "Format All + Download" then click on download button
remember never connect phone before the above steps only connect phone after u click on Download button
ndbhatt2006 said:
If your EMMC chip or RAM is damaged by Mobile repairing person then you will be helpless...
but if it is ok then once again try, this time in SP Flash tool select option "Format All + Download" then click on download button
remember never connect phone before the above steps only connect phone after u click on Download button
Click to expand...
Click to collapse
Where is this option Format all + download?
MrJukeHardbane said:
Where is this option Format all + download?[/Qwhi
which version of sp flash tools you use?
if its V5 or higher
then you will find it as per attached image.
Click to expand...
Click to collapse
ndbhatt2006 said:
MrJukeHardbane said:
Where is this option Format all + download?[/Qwhi
which version of sp flash tools you use?
if its V5 or higher
then you will find it as per attached image.
Click to expand...
Click to collapse
Still same error. I guess its as good as a paperweight now.
Click to expand...
Click to collapse
MrJukeHardbane said:
ndbhatt2006 said:
Still same error. I guess its as good as a paperweight now.
Click to expand...
Click to collapse
now there should be hardware problem you can get checked with service center.....
Click to expand...
Click to collapse
ndbhatt2006 said:
MrJukeHardbane,
First of all you need to download A116 Stock ROM, Drivers and SP Flash Tools by googling.
Then Remove your battery of the phone and SIM cards as well as Memory card,
Then install A116 Drivers in your PC then open SP flash tools window by double clicking on Flash_Tools.exe
the windows of SP Flash tool will open then click on Scatter Loading and search for the A116 Stock ROM you downloaded and extracted and find MT6589_Android_scatter_emmc file and open it
find the Download button on the upper side of window and click on it
Then connect your phone to PC with the data cable and try pressing volume up button and power butter simultaneously 3 to 4 times them you can see at the base of the window your phone will get detected and connected with the port and rest process will be done automatically wail till you see the green circle on the screen.
Once you find green circle remove your device and try to start after fixing Battery and Sim card and memory card.
If your phone is soft bricked... It will definitely boot up and it takes about 10 minutes at first boot up so keep patience..
HIT THANKS IF I HELPED YOU :good:
Click to expand...
Click to collapse
Can we flash custom roms from sp flash tool (the ones which we flash from Cwm recovery)
---------- Post added at 02:12 AM ---------- Previous post was at 02:08 AM ----------
ndbhatt2006 said:
MrJukeHardbane,
First of all you need to download A116 Stock ROM, Drivers and SP Flash Tools by googling.
Then Remove your battery of the phone and SIM cards as well as Memory card,
Then install A116 Drivers in your PC then open SP flash tools window by double clicking on Flash_Tools.exe
the windows of SP Flash tool will open then click on Scatter Loading and search for the A116 Stock ROM you downloaded and extracted and find MT6589_Android_scatter_emmc file and open it
find the Download button on the upper side of window and click on it
Then connect your phone to PC with the data cable and try pressing volume up button and power butter simultaneously 3 to 4 times them you can see at the base of the window your phone will get detected and connected with the port and rest process will be done automatically wail till you see the green circle on the screen.
Once you find green circle remove your device and try to start after fixing Battery and Sim card and memory card.
If your phone is soft bricked... It will definitely boot up and it takes about 10 minutes at first boot up so keep patience..
HIT THANKS IF I HELPED YOU :good:
Click to expand...
Click to collapse
And can u send link for stock Rom and drivers for mmx a116? Please

[Q] Google Calendar not syncing (VIBEUI 2)

Hi,
I installed Lenovo P780 VibeUI 2.0 version: VIBEUI_V2.0_1512_DEV_P780 and gapps-kk-20150404-minimal-edition-signed.zip.
Then I installed Google Calendar from Play Store. Unfortunately it doesn't sync. If I go to settings/accounts/google there is no "google calendar data" option to choose.
marekjarosz said:
Hi,
I installed Lenovo P780 VibeUI 2.0 version: VIBEUI_V2.0_1512_DEV_P780 and gapps-kk-20150404-minimal-edition-signed.zip.
Then I installed Google Calendar from Play Store. Unfortunately it doesn't sync. If I go to settings/accounts/google there is no "google calendar data" option to choose.
Click to expand...
Click to collapse
Try to install full gapps pack.
Sent from my Lenovo P780
stympy said:
Try to install full gapps pack.
Click to expand...
Click to collapse
Any recommended source?
marekjarosz said:
Any recommended source?
Click to expand...
Click to collapse
Try the pack from cyanogen.
Sent from my SMT TAB 704DC
stympy said:
Try the pack from cyanogen.
Click to expand...
Click to collapse
Unfortunately I used [GApps][4.4.2][AROMA]_Aroma_Installer_GApps-v1.5.2 and didn't wipe data before/after. After rebooting the phone got "Lenovo launcher stopped, must be closed". After swithching the phone off and on end up with an infinite bootloop.
I rebooted the phone into recovery mode and wiped data, cache and dalvik and tried to reinstall VIBEUI_V2.0_1512_DEV_P780. After the first launch there is only a chinese text (I guess it might be some error, after clicking the button the same error apears again and again).
I tried to flash a custom revovery (as I end up with a Lenovo-Recovery with nothing to do) with a Flash Tool V5.13.52.200 as described in other thread but after clicking "download" and connecting the phone nothing happens (phone shows red light and a battery charge screen). The phone is recognized by the PC (Win 7) as even after turning the phone on again it is possible to upload files to the SD card using windows explorer.
marekjarosz said:
Unfortunately I used [GApps][4.4.2][AROMA]_Aroma_Installer_GApps-v1.5.2 and didn't wipe data before/after. After rebooting the phone got "Lenovo launcher stopped, must be closed". After swithching the phone off and on end up with an infinite bootloop.
I rebooted the phone into recovery mode and wiped data, cache and dalvik and tried to reinstall VIBEUI_V2.0_1512_DEV_P780. After the first launch there is only a chinese text (I guess it might be some error, after clicking the button the same error apears again and again).
I tried to flash a custom revovery (as I end up with a Lenovo-Recovery with nothing to do) with a Flash Tool V5.13.52.200 as described in other thread but after clicking "download" and connecting the phone nothing happens (phone shows red light and a battery charge screen). The phone is recognized by the PC (Win 7) as even after turning the phone on again it is possible to upload files to the SD card using windows explorer.
Click to expand...
Click to collapse
Hi. Try to reflash using SP Flash Tool v5 from my post Rooting Tutorial for KK.
I use ONLY those tools. Tested and modified for P780.
Sent from my Lenovo P780
stympy said:
Hi. Try to reflash using SP Flash Tool v5 from my post Rooting Tutorial for KK.
I use ONLY those tools. Tested and modified for P780.
Click to expand...
Click to collapse
I used exactly those tools, but with a results described below:
I tried to flash a custom revovery (as I end up with a Lenovo-Recovery with nothing to do) with a Flash Tool V5.13.52.200 as described in other thread but after clicking "download" and connecting the phone nothing happens (phone shows red light and a battery charge screen).
Click to expand...
Click to collapse
marekjarosz said:
I used exactly those tools, but with a results described below:
Click to expand...
Click to collapse
seems to me that your phone is no longer detected by your computer !
se this:
1. go to device manager
2. with device manager window open plug your phone
3. in device manager in Ports tab something like MTK 65XX... will appear for 1 or 2 secconds
Tell me if this is going on !
stympy said:
seems to me that your phone is no longer detected by your computer !
se this:
1. go to device manager
2. with device manager window open plug your phone
3. in device manager in Ports tab something like MTK 65XX... will appear for 1 or 2 secconds
Tell me if this is going on !
Click to expand...
Click to collapse
My device is detected by my computer as I am able to copy files to SD card using windows explorer. I plug the phone and I see "Lenovo P780" in My Computer, then I open it and get access to internal memory and SD card.
BUT - I do not see it in the Device Manager at all... Maybe I will try to do it on the other Windows computer?
marekjarosz said:
My device is detected by my computer as I am able to copy files to SD card using windows explorer. I plug the phone and I see "Lenovo P780" in My Computer, then I open it and get access to internal memory and SD card.
BUT - I do not see it in the Device Manager at all... Maybe I will try to do it on the other Windows computer?
Click to expand...
Click to collapse
Try what i told you with the phone powered off!
The computer must have windows XP or windows 7!
Good Luck.
stympy said:
seems to me that your phone is no longer detected by your computer !
se this:
1. go to device manager
2. with device manager window open plug your phone
3. in device manager in Ports tab something like MTK 65XX... will appear for 1 or 2 secconds
Tell me if this is going on !
Click to expand...
Click to collapse
After connecting switched-off phone to the USB port MT65xx Preloader appears in the Device Manger for 1-2 seconds.
marekjarosz said:
After connecting switched-off phone to the USB port MT65xx Preloader appears in the Device Manger for 1-2 seconds.
Click to expand...
Click to collapse
Hi. You are lucky. Your phone is detected by your computer !
All you have to do is to flash a custom recovery TWRP CN Version.
After this you could download your firmware again and put it on sd card ! reboot to recovery wipe and reflash your firmware !
stympy said:
Hi. You are lucky. Your phone is detected by your computer !
All you have to do is to flash a custom recovery TWRP CN Version.
After this you could download your firmware again and put it on sd card ! reboot to recovery wipe and reflash your firmware !
Click to expand...
Click to collapse
Thanks for your reply, but as I wrote before I don't really know how to achieve it as it is not possible to do it using Flash Tool
marekjarosz said:
Thanks for your reply, but as I wrote before I don't really know how to achieve it as it is not possible to do it using Flash Tool
Click to expand...
Click to collapse
If you want i can help you. All you need is a connection by team viewer.
Sent from my Lenovo P780
I used [TUT] Instructions MTK6577 USB VCOM Driver Installation to install a proper driver and was able to flash a custom ROM to make it work as suppose to and was able to do the rest without any problems.
Thank you

Can't go to download mode - phone is booting into system

hi,
As is thred name - can't go to download mode - after connecting to PC phone is bootlooping into system
Help
borda01 said:
hi,
As is thred name - can't go to download mode - after connecting to PC phone is bootlooping into system
Help
Click to expand...
Click to collapse
What do you want to do?
Flash rom inne flash tool
borda01 said:
Flash rom inne flash tool
Click to expand...
Click to collapse
Your phone is not powering down ?
Lenovo P780 is flashed by powering down.
You power down the phone, prepare to flash and when you are ready just plug the USB cable with the phone powered down.
That is it.
That not works, phone is powered down, but after connecting cable is powering on into system...
borda01 said:
That not works, phone is powered down, but after connecting cable is powering on into system...
Click to expand...
Click to collapse
Try this:
When the procedure to flash is ready, with the USB cable connected press the red button and keep the button pressed, then press download in SP Flash Tool and release the button. Do all this in this order. Tell me what is going on?
The flash should start.
stympy said:
Try this:
When the procedure to flash is ready, with the USB cable connected press the red button and keep the button pressed, then press download in SP Flash Tool and release the button. Do all this in this order. Tell me what is going on?
The flash should start.
Click to expand...
Click to collapse
Phone is booting, sp flash tool "searching"
Phone has TWRP installed, but I can't install any ROM - error appears
borda01 said:
Phone is booting, sp flash tool "searching"
Phone has TWRP installed, but I can't install any ROM - error appears
Click to expand...
Click to collapse
What firmware do you have installed now?
stympy said:
what firmware do you have installed now?
Click to expand...
Click to collapse
(vibeui_v2.0_1443_7.25.1_st)
In device manager phone is detected as MT65XX preloader in about 5 seconds - after that it bootloops.
EDIT:
solution:
Open "Device Manager" on your Windows PC.
Plug in your phone through the micro USB cable. A device will show up for a few seconds in "Device Manager". After that, it will disappear again!
Recognize the device tree where it appeared, and wait for it as you unplug and plug in your phone again (if bootloop, its automatic!)
Catch it with a right click as it appears! Then choose "Update Drivers" and pick the directory where you uncompressed the drivers you downloaded above. Its ok if after catching it the device disconnects. You only need to install the drivers now.
Click to expand...
Click to collapse
borda01 said:
In device manager phone is detected as MT65XX preloader in about 5 seconds - after that it bootloops.
Click to expand...
Click to collapse
I understand now. Your computer does not recognize your phone. The drivers are not installed at all or correctly.
Download the drivers from here and install them. The drivers are at the bottom of the page.
To flash use only the sp flash tools from here.
Small tutorial to install the drivers:
I think was someting like this:
1. First install the .exe file. Reboot PC.
2. Now plug the phone to the PC and new hardware wizard will appear. Unplug the USB cable.
3. Now power off the phone.
4. Again plug the phone this time powered off.
5. At this time in Device Manager appears for a second or two not in USB area, in ports area something with.. MTK65xx...
6. Click very fast on it because that will dessapear fast.
7. After you clicked on it all you have to do is update driver, and voila you have drivers installed and now all you have to do is to flash you ROM.
Hope this will help you.
Good luck.
What is a newest version of TWRP for P780?
borda01 said:
What is a newest version of TWRP for P780?
Click to expand...
Click to collapse
For normal layout is TWRP 2.8.4.0 rev.2 and for + layout is 3.0.2-7.

Categories

Resources