Related
How to fix partion problem !!!
After countlss hours of messing with the LG P769 This is how i got into S/W mode to work !:laugh:
ASSUMING you know how to install fastboot drivers there are instructions on the forum ...so follow those guide note fastboot drivers work best on windows 7 windows 8 was giving me hard time ...
1.install fastboot drivers
2.run lelus script at the same time hold vol+ button once the script shows the OMAP device close the script and immediately put the battery back in .The LG phone will boot into S/W mode !
Make sure you write down your imei or serial number AND make sure battery is fully charged . then
Now simply use the LG software tool or the KDZ offline flasher look around the forum for how to guides
Thats it
tawhid111 said:
How to fix partion problem !!!
After countlss hours of messing with the LG P769 This is how i got into S/W mode to work !:laugh:
ASSUMING you know how to install fastboot drivers there are instructions on the forum ...so follow those guide note fastboot drivers work best on windows 7 windows 8 was giving me hard time ...
1.install fastboot drivers
2.run lelus script to get into fastboot at the same time hold vol+ button once the script shows the OMAP device close the script and immediately put the battery back in .The LG phone will boot into S/W mode !
Make sure you write down your imei or serial number AND make sure battery is fully charged . then
Now simply use the LG software tool or the KDZ offline flasher look around the forum for how to guides
Thats it
Click to expand...
Click to collapse
So you solve it! :good:
:/
tawhid111 said:
How to fix partion problem !!!
After countlss hours of messing with the LG P769 This is how i got into S/W mode to work !:laugh:
ASSUMING you know how to install fastboot drivers there are instructions on the forum ...so follow those guide note fastboot drivers work best on windows 7 windows 8 was giving me hard time ...
1.install fastboot drivers
2.run lelus script at the same time hold vol+ button once the script shows the OMAP device close the script and immediately put the battery back in .The LG phone will boot into S/W mode !
Make sure you write down your imei or serial number AND make sure battery is fully charged . then
Now simply use the LG software tool or the KDZ offline flasher look around the forum for how to guides
Thats it
Click to expand...
Click to collapse
Still unable to do it, when I plug the cable holding vol+ it just reboot normally :/
foreverman said:
Still unable to do it, when I plug the cable holding vol+ it just reboot normally :/
Click to expand...
Click to collapse
Then try enter in lelus fastboot mode, ad then flash x-loader, uloader, boot.img and recovery.img from stock rom for your device type model. Then repeat steps 1 and 2
Where can I find the lelus script?
Sent from my Note II
Sorry for reviving such an old thread, but oh well...
Your procedure doesn't seem to work with my device. Just to make sure we are using the same driver packages, can you post a link to the fastboot driver you have successfully used?
My L9 is always showing this "partition doesn't exist" error message, no matter what I try. Lelus's script seems to do the job and the phone is detected as a fastboot device, and can even be detected in LG Flash Tool (using a 910K cable), but flashing will stop after a little over 2 minutes, because the phone disconnects. During all of my attempts, the screen stays black.
Any hint?
ciccillover said:
Sorry for reviving such an old thread, but oh well...
Your procedure doesn't seem to work with my device. Just to make sure we are using the same driver packages, can you post a link to the fastboot driver you have successfully used?
My L9 is always showing this "partition doesn't exist" error message, no matter what I try. Lelus's script seems to do the job and the phone is detected as a fastboot device, and can even be detected in LG Flash Tool (using a 910K cable), but flashing will stop after a little over 2 minutes, because the phone disconnects. During all of my attempts, the screen stays black.
Any hint?
Click to expand...
Click to collapse
Then you need a Technician with a Octopus Box to repair your partition table...
ciccillover said:
Sorry for reviving such an old thread, but oh well...
Your procedure doesn't seem to work with my device. Just to make sure we are using the same driver packages, can you post a link to the fastboot driver you have successfully used?
My L9 is always showing this "partition doesn't exist" error message, no matter what I try. Lelus's script seems to do the job and the phone is detected as a fastboot device, and can even be detected in LG Flash Tool (using a 910K cable), but flashing will stop after a little over 2 minutes, because the phone disconnects. During all of my attempts, the screen stays black.
Any hint?
Click to expand...
Click to collapse
Can you boot into recovery? We now have a custom recovery for locked bootloaders (and CM roms). If you can get into recovery, I would try some adb commands to mount the partitions.
No, no recovery. Just to make sure that I'm not doing it wrong, what is the key combination to boot to recovery?
I have also tried:
Code:
fastboot boot some_recovery_image.img
It says ok, but the phone just hangs at the black screen and becomes undetectable as a fastboot device, until I pull the battery. So, unless the some_recovery_image.img is unsuitable for my P760 (which may be!), there is something seriously wrong I think.
Or maybe I can try the same command with the custom recovery for bootloader locked phones... Where can I find it?
ciccillover said:
No, no recovery. Just to make sure that I'm not doing it wrong, what is the key combination to boot to recovery?
I have also tried:
Code:
fastboot boot some_recovery_image.img
It says ok, but the phone just hangs at the black screen and becomes undetectable as a fastboot device, until I pull the battery. So, unless the some_recovery_image.img is unsuitable for my P760 (which may be!), there is something seriously wrong I think.
Or maybe I can try the same command with the custom recovery for bootloader locked phones... Where can I find it?
Click to expand...
Click to collapse
Your EMMC partition is wiped or fried... you really need a JTAG service or a Box like octopus because your L9 is Hard-bricked...
Thanks for your opinion. Yet, I still want to hear from others.
I'm running into more and more problems with the L9 as their me grows.
-Fastboot doesn't work under Windows 8.1 and 10, but under the now obsolete(for me) Windows 7, unlike my other devices, which are fine with Win 10.
-ADB seems to work, but requiring the device to be still able to boot.
-I always boot to recovery from within Android as long as the L9 ain't bricked. After a failed rom install, during which the sd card failed(could no longer write or be formatted afterwards, the last time stamps of files and folders were set during the failed install) I discovered a problem with TWRP(Artas182x's and Edwin's), which may have been present since a long time: Trying to invoke TWRP via keypress will brick the device!
So, if my P760 no longer boots, there's only download mode available, sort of the final line of defense.
-There's sort of a trick if even download mode fails: After a failed attempt unplug phone, force switch-off, if the phone is in brick state. Then switch on, force switch-off again, and only then attempt download mode again. And have patience while holding down the vol button, it might take up to 20 seconds for the phone to switch itself on into download mode. (A single forced powerdown will cause Fastboot NOT to work the next time)
But I'm absolutely clueless about the recovery issue, for now TWRP is semi-working, can only be accessed via Android, as long as the phone is fully working.
W/o Fastboot, I now have flashed stock rom several times and rooted it with Kingo rooter just to be able to run Flashify to install TWRP. If Flashify is the culprit for the TWRP issues, I could need a recommendation for a better working app.
ciccillover said:
Thanks for your opinion. Yet, I still want to hear from others.
Click to expand...
Click to collapse
Tried OMAP flasher ? It needs memory configuration file in order to work with our device
No, I didn't. I have sold the phone for spares.
Inviato dal mio LG-D855 utilizzando Tapatalk
I never needed the OMAP drivers and tools. As they are ancient, they will probably make even more problems with newer Windows versions.
I could by no means invoke Fastboot on this device with Windows 8.1 and 10, Seven worked. So you had to go for Download Mode instead to recover to stock rom, then root with the Kingo tool, then install TWRP via Rashr or Flashify, the most time consuming way to recover from the frequent bricks.
And the LG Flash Tool 2014 always needed several attempts to get the job done. The latest official recovery tool from LG works in D/L Mode, but will always download the rom image anew.
I have a VIBEZ K910 with locked bootloader after upgrading to version 4.4.2. Now it's bricked. Cannot enter test mode with the combination Volumn - and Power button. I think the droidboot.img is damaged. Cannot enter recovery either. Anybody can help me unbrick the phone? Pls:crying:
Sorry to hear about your bricked phone. I can't help specifically as I don't have a Lenovo, but having a search around XDA there seems to have been some success reported in the following thread:
http://forum.xda-developers.com/showthread.php?t=2597590
See this post - http://forum.xda-developers.com/showpost.php?p=52013378&postcount=412
Another post in that thread suggests:
Turn off the phone --> Run minimal ABD and fastboot as admin--> just write the command for recovery install (don't hit enter yet)--> press volume + and volume - button and connect the phone to pc via usb--> now hit enter and voila. Your phone will boot in recovery.
Click to expand...
Click to collapse
Good luck!
anyone?
f4780y said:
Sorry to hear about your bricked phone. I can't help specifically as I don't have a Lenovo, but having a search around XDA there seems to have been some success reported in the following thread:
http://forum.xda-developers.com/showthread.php?t=2597590
See this post - http://forum.xda-developers.com/showpost.php?p=52013378&postcount=412
Another post in that thread suggests:
Good luck!
Click to expand...
Click to collapse
i tried this aldready, but my phone is locked bootloder so that method is no help. Thank you for your support anyway.
hientran41 said:
i tried this aldready, but my phone is locked bootloder so that method is no help. Thank you for your support anyway.
Click to expand...
Click to collapse
OK, but did you look at the second link there, to the specific post in that thread? It suggests a process for locked bootloader, which is why I thought it might help...
Anyhoo, I hope you manage to get it fixed somehow!
Is anybody have the droidboot.img file from the VibeZ K910 dualsim, pls upload it for me. i cannot find it anywhere.
I look into the second link as well. that method for user have a working phone but locked bootloader and want to downgrade.
Ah, OK. Sorry I couldn't help.
u fix your phone?
hientran41 said:
I have a VIBEZ K910 with locked bootloader after upgrading to version 4.4.2. Now it's bricked. Cannot enter test mode with the combination Volumn - and Power button. I think the droidboot.img is damaged. Cannot enter recovery either. Anybody can help me unbrick the phone? Pls:crying:
Click to expand...
Click to collapse
hi do u fix your phone?
Geguniukas said:
hi do u fix your phone?
Click to expand...
Click to collapse
i bricked also
dunno what to do..
---------- Post added at 12:13 AM ---------- Previous post was at 12:13 AM ----------
hientran41 said:
I have a VIBEZ K910 with locked bootloader after upgrading to version 4.4.2. Now it's bricked. Cannot enter test mode with the combination Volumn - and Power button. I think the droidboot.img is damaged. Cannot enter recovery either. Anybody can help me unbrick the phone? Pls:crying:
Click to expand...
Click to collapse
did you fixed the phone?
lenovo k910e 4.2.2 bricked after TWRP for 4.4.2 installation
Hi , this is my first time on the site , so forgive me if ive posted this in the wrong place.
I briked my Lenovo k910e running 4.2.2 rom with google apps purchased off Aliexpress.
What i did was run the flashrec.exe file for TWRP , but not until too late did i realise it was for 4.4.2 instead of 4.2.2.
Now i cannot boot the phone , TWRP was successfully installed and operational , but after about 20 reboots TWRP flash screen is stuck on the TeamWin logo and not accessable.
Ive tried mostl sugestions on this site and others without luck.
I can get the phone recognised with fastboot only after these commands ;
cd downloads
cd fastboot
adb devices
and it seems i may be able to push files to my device.
Is there a working link to the k910 OEM rom k910_ss_s_2_040_0109_131226 someone could direct me to.
All the links i have found so far are corrupted. Is there a way of repairing the TWRP recovery i have in the phone now.
Am I correct in assuming I have to install the OEM factory 4.2.2 ROM to wipe TWRP and istal Lenovo recovery ?.
Any help would be so appreciated. Thanks
Solution ( k910 bricked )
Ok here is the solution even if your device ( k910 dual sim ) is completely bricked as was mine.
I was stuck in Lenovo logo with no success in finding right and working drivers ( windows 7 64x ) and i was not able to to get in recovery official ...everything was just - somehow - deleted...
I had locked bootloader **** and was not be able to flash cmw in working mode ****
There was nothing for me that could recover my phone even if the "hard" way with QPST or miflash etc
So....after 3 days....find this solution and hope this will help you because it is soooooooooo easy finally!
Steps:
1) Download lenovo driver ( i think it is useless in fact but ok....just run it you dont have anything more to loose )
https://www.dropbox.com/s/frbpz16udrefoit/LenovoUsbDriver_autorun_1.0.112.exe?dl=0
2a) Download and install Minimal adb
https://www.dropbox.com/s/uvngsu4vz4hvsky/minimal_adb_fastboot_v1.1.3_setup.exe?dl=0
So now you have to use the right recovery image ( this file has to be inside minimal adb folder )....so here it is:
https://www.dropbox.com/s/ge05m1fe8n4qgb1/recovery.img?dl=0
2b)
Download this ROM ( this worked for me - with other i did try i did get an error )
http://www.needrom.com/download/lenovo-k910-vibeui-2-0/
prefer the last updated version ( 1501 )
Put this rom in the same ADB folder and renale zip in VIBE1411.ZIP ( in order to be easier later )
3) Turn off the device open Adb and write : fastboot boot recovery.img ( to have it ready )
4) Push volume + $ volume - at the same time and AFTER connect with usb to your pc - At the time the device will vibrate HIT ENTER in ADB
This will flash the recovery and after 1 minute device will open in a recovery screen with an adb update option ***
SELECT THIS adb update OPTION !
Your device kow it is ready to flash the new rom ! ( you will realize that everything is right from many usb beeps you will hear )
5)In adb console write : adb sideload VIBE1411.ZIP
This will take a little ....after that your device will reboot ! Dont panic if for a few minutes it will stuck in lenovo logo....
IT IS NORMAL AND YOU HAVE TO WAIT!
Hope this will help you.....please feel free to tell me if this worked for you.
C u
Same thing happens to my lenovo vibe z k910
buzzbuzz1 said:
Hi , this is my first time on the site , so forgive me if ive posted this in the wrong place.
I briked my Lenovo k910e running 4.2.2 rom with google apps purchased off Aliexpress.
What i did was run the flashrec.exe file for TWRP , but not until too late did i realise it was for 4.4.2 instead of 4.2.2.
Now i cannot boot the phone , TWRP was successfully installed and operational , but after about 20 reboots TWRP flash screen is stuck on the TeamWin logo and not accessable.
Ive tried mostl sugestions on this site and others without luck.
I can get the phone recognised with fastboot only after these commands ;
cd downloads
cd fastboot
adb devices
and it seems i may be able to push files to my device.
Is there a working link to the k910 OEM rom k910_ss_s_2_040_0109_131226 someone could direct me to.
All the links i have found so far are corrupted. Is there a way of repairing the TWRP recovery i have in the phone now.
Am I correct in assuming I have to install the OEM factory 4.2.2 ROM to wipe TWRP and istal Lenovo recovery ?.
Any help would be so appreciated. Thanks
Click to expand...
Click to collapse
After running twrp recovery it operates 3-4 times but now it flashes on twrp screen and screen goes blank and again flashes . I am unable to on it and as it shows only light and lenovo logo after that blank screen . Please help me in this. Its only detecting in adb recovery not any other mode.
lenove vibe Z k910 locked and stuck in logo
hello all
I ve done every word and many other tutorials but still the problem the same:
adb devices give just nothing
but fastboot devices gives the device
the driver is installed correctly detected in devices of the computer
here is the response for :fastboot boot recovery.img:
~/Desktop/lenovo]$ fastboot boot recovery.img (masterā±)
< waiting for device >
downloading 'boot.img'...
OKAY [ 0.536s]
booting...
FAILED (remote: Locked)
finished. total time: 0.538s
thanks for everyone to help
Boot into recovery under bricked condition
Today I bricked K910 after reinstalling GMS apk.
The phone hanged at boot logo.
Nothing can be from here.
I decided to take this risk.
I removed the back cover and disconnected the battery terminal.
After that I plugged back the terminal.
Several tries by power button and volume down to get into the recovery mode. All failed.
Each time it hanged at boot logo.
I have to redo the battery terminal unplug sequence again.
This is correct method to get into recovery mode.
Press power button and volume down till the Lenovo logo appears.
Move the power button finger to the position of the " Home " of the touchscreen position.
Hold till the recovery menu appears. Choose factory reset to erase the phone.
There was two lit small icon below. Make your choice.
The phone will be erased by reset.
Reboot after the process.
I solved my phone bricked problem.
Hope the method will solve your problem.
Good day to all K910 users.
my vibe z cannot access the recovery mode (PWR + VLM DOWN), it only vibrate. If turn on only stuck at Logo. Please help .
So i stupidly installed chainfire 3d restarting my phone to a boot loop, i tried doing a hard reset still it restarted back to boot loop , I tried flashing a stock rom/kdz for my phone into lg support tool/r&d test tool, but every time i put it into s/w upgrade mode my pc dosent recognize it, it just says Usb device Not recognize , it also says device driver software was not successful , and i did
try installing my phone driver from the lg websites but yet it still dosent recognize it. I think this is the only problem thats blocking my way to unbrick my phone. I don't know if I'm installing the wrong driver or my phone
If you know the right driver for my phone can you please reply with the link, I would be appreciated for your help.
my phone is also locked boot loader.
sorry for my bad english
Did you install recovery? If yes, go to recovery mode, mount /system, run adb shell from computer and type these command:
Code:
su
cd /system/lib
sh ./cf3d_uninstall.sh
It'll run that script and uninstall CF3D from your phone.
Hi!
First off let me say thanks to R_a_z_v_a_n for redirecting me and hope that I'll find my answer here ^^
So I Have this device called HP 7 VoiceTab 1321RA (not with Slate just HP 7 Voicetab), wanting to have a custom recovery then I tried to flash a CWM Custom Recovery for HP Slate 7 VoiceTab because I thought it was the same and ends up bricking my phone. It ends up in a bootloop which only shows HP sign for a few seconds and dead. But I managed to find out that I can access the recovery menu (or so I thought it is), but the options was choosing between Fastboot Mode, Normal Boot, Recovery Mode, and VART Mode.
I tried to enter Fastboot Mode before and tried to access it via PC but somehow I can't find the device by entering adb devices and fastboot devices. Anyways, I have downloaded a stock update.zip for it but not the original KitKat one which I get from the first time I bought it but rather the JB ones. I think by flashing this would help me recover the device but the only problem is I don't know which method should I use to Flash it. Since I don't have the Stock Recovery or ANY kind of recovery at all, I guess I'm stuck. And it won't start to the home page so I can't set the USB debugging options. Please guide me through this >.<
Thanks a lot!
Been fighting with it for 2 days now and still no result came.
So here's the update so far....
I tried on my other device in order to understand how my PC reads ADB and now I kinda gets it. But the problem is now can't get the device to enable USB Debugging because I can't access options at all.
Secondly, since I left it on for the night because charging seems to trigger the bootloop too, now I can't access the fastboot mode like I was last night. And it constantly repeating this sequence: [battery scene with the "charging battery" symbol] > [HP Powered by Android screen] repeated for 2-3 times > [low battery need charging screen] > repeat. And once I tried to connect to the PC, it goes to the same sequence too. When I tried to access the boot options (the screen which displays Fastboot Mode, Normal Boot, Recovery Mode, and UART Mode which I mention in Thread Starting post), it shows the low battery need charging scene and then repeating the same sequence as mentioned above.
I seem to figure out how to fix this but I still can't manage to access the fastboot mode yet. Will give update once I can try to.
Anyone can help me on this?
Thanks a lot!
Update!
Somehow with a little tweaking and stripping the device, I managed to solve the charging problems. Will update on this once my problem finished.
Jump out from the frying pan and into the fire so they say, I ran into another problem. Finally managed to get into fastboot mode, the devices manager reads it as an Android Device>ROMaster ADB device like the other device I tried to connect while in ADB mode and fastboot mode, but somehow CMD cannot read the device as an ADB device or a Fastboot device like the other device did. I tried to uninstall and reinstall the driver and still nothing happens. I tried to find the usb_driver on the internet and it directs me to the update.zip instead. Trying to update the driver via Computer Management but it says the driver is up to date. Now thinking about making an emulator device based on the HP 7 VoiceTab 1321RA but I really have no idea how to make one. Any one have any idea of what should I do next or can guide me through this? At least until the CMD can read the fastboot.
Thanks a lot!
I found my self in a deadlock!
PLEASE HELP :crying:
Could you unbrick yours
What service centre says about that problem i also ran in this problrm but i m trying to go to service centre for that
first off install drivers in your PC as admin
then use the official flashtool to flash ur stock firmware by entering fastboot or flashmode simple as that
@Sunderesh, thanks for the suggestion, however, couldnt get any official flashtool for hp voicetab. Can you suggest one please?
jithinraj said:
@Sunderesh, thanks for the suggestion, however, couldnt get any official flashtool for hp voicetab. Can you suggest one please?
Click to expand...
Click to collapse
Dude urs is a mtk device so sp flash tool should do the trick.... Just don't forget to install correct drivers....run both drivers and flash tool as admin..... Tell me when it's solved k
jithinraj said:
@Sunderesh, thanks for the suggestion, however, couldnt get any official flashtool for hp voicetab. Can you suggest one please?
Click to expand...
Click to collapse
That is what im trying. To tell you urs is a mediatek device the official flashtool is sp flashtool
rikicchi said:
Update!
Somehow with a little tweaking and stripping the device, I managed to solve the charging problems. Will update on this once my problem finished.
Jump out from the frying pan and into the fire so they say, I ran into another problem. Finally managed to get into fastboot mode, the devices manager reads it as an Android Device>ROMaster ADB device like the other device I tried to connect while in ADB mode and fastboot mode, but somehow CMD cannot read the device as an ADB device or a Fastboot device like the other device did. I tried to uninstall and reinstall the driver and still nothing happens. I tried to find the usb_driver on the internet and it directs me to the update.zip instead. Trying to update the driver via Computer Management but it says the driver is up to date. Now thinking about making an emulator device based on the HP 7 VoiceTab 1321RA but I really have no idea how to make one. Any one have any idea of what should I do next or can guide me through this? At least until the CMD can read the fastboot.
Thanks a lot!
Click to expand...
Click to collapse
try to push the update.zip via adb sideload (Choose "update via ADB sideload" on recovery mode)using adb terminal on PC,as long as your tab can access the recovery mode.remember to backup all your data before u do it.
have a try it's 100% work on me
where I can download update.zip file? anyone can help?
rikicchi said:
Update!
Somehow with a little tweaking and stripping the device, I managed to solve the charging problems. Will update on this once my problem finished.
Jump out from the frying pan and into the fire so they say, I ran into another problem. Finally managed to get into fastboot mode, the devices manager reads it as an Android Device>ROMaster ADB device like the other device I tried to connect while in ADB mode and fastboot mode, but somehow CMD cannot read the device as an ADB device or a Fastboot device like the other device did. I tried to uninstall and reinstall the driver and still nothing happens. I tried to find the usb_driver on the internet and it directs me to the update.zip instead. Trying to update the driver via Computer Management but it says the driver is up to date. Now thinking about making an emulator device based on the HP 7 VoiceTab 1321RA but I really have no idea how to make one. Any one have any idea of what should I do next or can guide me through this? At least until the CMD can read the fastboot.
Thanks a lot!
Click to expand...
Click to collapse
can you explain how did you managed to charge the device??? please its a request......jst help me out :crying::crying:
Hey, so basically i got my phone into bootloop and dont know how to get it back. I dont have a recovery, so i tried to flash one, but my pc isnt recognizing my phone, adb or fastboot says "waiting for device". I cant do anything in Android tho, because i cant boot into the system, so what should i do? Please help, thanks