So I got my self to thinking; What is the best way to handle connectivity for my devices?
I have a rooted/rom'd Evo Shift, and will have my gTab soon (hopefully). I generally leave BT on my phone on all the time, and it is currently paired with my Car's head unit to stream audio and hands free calls.
Do I pair my table to my phone via BT and tether?
What are the consequences of leaving that on all the time? How would that affect the battery life of the phone and tablet? I know in the old days when you used the PAM (phone as modem) your phone didn't get any internet connectivity. Is that the case with BT tethering?
Do I pair my tablet with my head unit? I don't know if it can be paired with more then one device. I doubt it though. Maybe just pair hands free from my phone and a2dp from the gtab? Not sure if that is possible, have to read the head unit's manual.
I apologize for the incoherent ramblings. I'm trying to figure out what other people have done along with what works well, or what doesn't work at all.
Thanks,
So I've read up a little more and found some answers.
Looks like I can get GPS information from my phone via blue tooth. This will be awesome in the car. Any one who has done this, is it possible to get internet tethering via blue tooth from the same phone at the same time?
Using wifi to tether data while i use blue tooth for GPS information is possible, but doesn't seem very elegant.
It doesn't look like my head unit can have multiple BT pairings active at the same time. Guess I will have to use an aux cable for the tab and BT for my phone.
An ideal solution would be for my tab to use wifi for internet if available, and tether via BT to my phone if a wifi network is not available. It would be nice to leave the tethering open all day, but I think that would drain my phones battery something fierce. My over all concept it to have a personal network of interconnected devices with my phone acting as their connection to the internet.
Any advice, comments, death threats or criticism (constructive or not).
Bluetooth GPS sharing is very doable. There are several threads dedicated to setting this up. Looks like you may have found a few of them.
Tethering BT data to your phone is also very doable. Again, there are several threads on this, and I'm pretty active in most of them. Been working on this for a bit.
Start with this one:
http://forum.xda-developers.com/showthread.php?t=1001496
Wifi tethering is much easier. The issue I've had is mostly around BT and Wifi signal conflicts. I don't see it much in just using BT GPS and WiFi Data, but if I receive a call (I use a BT headset when on the road), the quality of my call is in the toilet for at least a minute or so. My guess is that the Tab is trying to get WiFI data from the phone (which it won't be able to because I'm on the phone - VZW CDMA - can't be on the Net and on phone at same time). After about a minute or so, it calms down. Unacceptable solution though.
So, I've now been mostly doing GPS & Data through Bluetooth to the phone. The problem with this hookup is again when I take a call, of course my Data drops on the tab (no way around that). But even worse, the GPS signal gets degraded too. I'm thinking just not enough Bluetooth bandwidth to support Headset, Data, and GPS at the same time?
So my most recent setup (just tried it for a bit today) is to use an external Bluetooth GPS (got one on Amazon for about $25.00) and then Bluetooth Tether to the phone for data. It's a little bit complicated, and involves yet another 'gadget', but I am getting the best results from this setup so far.
Thanks for the info.
I'm on sprint and know the "no data and voice" problem all to well. Even when using maps for navigation on my phone, if a call comes in, the GPS becomes retarded and inaccurate. Once the call ends, all is good.
with getting data from your phone via bluetooth, is that something you leave on all the time or do you have to turn on BT tethering when you want data?
grandebob said:
Thanks for the info.
I'm on sprint and know the "no data and voice" problem all to well. Even when using maps for navigation on my phone, if a call comes in, the GPS becomes retarded and inaccurate. Once the call ends, all is good.
with getting data from your phone via bluetooth, is that something you leave on all the time or do you have to turn on BT tethering when you want data?
Click to expand...
Click to collapse
I haven't been using that often to be honest. So when I do, I turn on BT tethering at that time.
I also use Co-Pilot for Navigation. It doesn't need data, just GPS. Map data is downloaded to the sdcard. Just depends on how I feel at that moment. Both nav systems have their advantages/disadvantages.
I'll have to check out co-pilot. storing maps for offline use sounds like a good idea, as long as they don't get stale.
OK, so I've kind of got blue tooth GPS data working. Using an app called "ShareGPS" on my phone and "BlueToothGPS" on my gtab, I've successfully gotten gps data to my tab. Using the BlueToothGPS app on my tab, i can see satellites and GPS data flowing. Unfortunately maps doesn't seem to get location data, and there doesn't appear to be a way to enable GPS data in any of the settings.
Running TnT lite. Any one know how I can get maps to see the GPS data?
I just got my Tab last night and while at work, decided to download a book that I'm in the middle of (Amazon archive). Our wifi at work is weak (to say the least) and I couldn't keep a connection long enough to download one book. It finally dawned on me that my rooted Evo has wireless tether. It worked like a champ! It's the first time I've used it and I gotta tell you, that alone made my day. Nice strong connection and I was able to websurf to my heart's content. I'm running TnT Lite 4.40.
I've searched around for some solid technique or, preferably, app that allows you to trick apps into thinking you are using Wifi when in reality you are still on 3g/4g.
- I am NOT looking for alternatives or workarounds for a specific app
I found it crazy that the iPhone has over a dozen apps, tweaks, etc that can easily do this type of thing, but the only stuff I've found on the subject for android were either ridiculous techniques that don't work, or people questioning WHY you'd want to do this...
If anyone has ANY information on this subject, please tell.
Is there a reason why this is so much harder on Android than on iPhone? I'd be happy to learn exactly what the problem is here.
bump
Im also interested on this. I have unlimited data and i find it ridiculous that devs make apps to only work on wifi. I use to use 3g unrestrictor all the time back when i had my iPhone.
bump
bump again...
Well i know this works with certain android games like zenonia and modern combat which require wifi not data connection so you can try it with other stuff. You have to be rooted.
The first step is to turn your Wi-Fi on and*download Android Wi-Fi tether app*available in Market.
Once you have the app downloaded, launch the app and go to Menu > Settings > Change > Setup Method and select Softap option.
Now start tethering and drag down the notification bar.
In case your Wi-Fi icon is still enabled, it means that you have done it right so far.
Do not press the Wi-Fi toggle icon and launch the game you want to play
-------------
I am a dishonest man, and you can always honestly trust a dishonest man to be dishonest. Honestly it's the honest ones you have to watch out for.
xMrArnoldx said:
Well i know this works with certain android games like zenonia and modern combat which require wifi not data connection so you can try it with other stuff. You have to be rooted.
The first step is to turn your Wi-Fi on and*download Android Wi-Fi tether app*available in Market.
Once you have the app downloaded, launch the app and go to Menu > Settings > Change > Setup Method and select Softap option.
Now start tethering and drag down the notification bar.
In case your Wi-Fi icon is still enabled, it means that you have done it right so far.
Do not press the Wi-Fi toggle icon and launch the game you want to play
-------------
I am a dishonest man, and you can always honestly trust a dishonest man to be dishonest. Honestly it's the honest ones you have to watch out for.
Click to expand...
Click to collapse
It didn't work.. My wifi is turned off as soon as the tethering starts. What app exactly am I supposed to use?
Thanks!
Try wifi tether for root users.
---------------------
Give me a thanks if i helped
Lg Lucid running Cm10
w/ Cm10 Kernel
Asus Tf700 running Cromi-X 4.6.5
w/ Max's v4 kernel
Some Android games and application require a Wi-Fi connection due to the large amount of data that they use. If you don't have Wi-Fi available, however, you won't be able to use the apps or play the games, even if you have a fast 3G connection. You can trick your phone into believing that the Wi-Fi is connected by saving a small text file to your SD card so the phone will play games and apps as if it's on Wi-Fi when it's only connected to 3G.
Things You'll Need
PC
Data cable
Text editing app
Instructions
1) Launch a text editing program on your computer and type "FALSE" in all caps. Save the file and give it the name "qaWifiOnlyMode.txt" exactly with all the lower-case and capital letters duplicated precisely, otherwise the Android operating system won't see the file. Close the text editing program.
2) Plug your Android device into your computer and drag your finger down from the top of the screen to open the notification area. Tap "USB Connected" and then confirm that you want to mount your SD card as a drive on the computer.
3) Find the qaWifiOnlyMode.txt file on your computer and click to select it. Press "Ctrl" and "C" to copy the file. Browse to the location of your Android device's SD card on your computer. In the base(root) directory, not in any sub-folder, press "Ctrl" and "V" to paste the text file to the card.
4) Drag down the notification area on your Android device and tap the USB connection to disconnect the device from the computer. Unplug the USB cable. Your device will now play games and apps as if it's on Wi-Fi even if it's only on 3G.
Diablo67 said:
Some Android games and application require a Wi-Fi connection due to the large amount of data that they use. If you don't have Wi-Fi available, however, you won't be able to use the apps or play the games, even if you have a fast 3G connection. You can trick your phone into believing that the Wi-Fi is connected by saving a small text file to your SD card so the phone will play games and apps as if it's on Wi-Fi when it's only connected to 3G.
Things You'll Need
PC
Data cable
Text editing app
Instructions
1) Launch a text editing program on your computer and type "FALSE" in all caps. Save the file and give it the name "qaWifiOnlyMode.txt" exactly with all the lower-case and capital letters duplicated precisely, otherwise the Android operating system won't see the file. Close the text editing program.
2) Plug your Android device into your computer and drag your finger down from the top of the screen to open the notification area. Tap "USB Connected" and then confirm that you want to mount your SD card as a drive on the computer.
3) Find the qaWifiOnlyMode.txt file on your computer and click to select it. Press "Ctrl" and "C" to copy the file. Browse to the location of your Android device's SD card on your computer. In the base(root) directory, not in any sub-folder, press "Ctrl" and "V" to paste the text file to the card.
4) Drag down the notification area on your Android device and tap the USB connection to disconnect the device from the computer. Unplug the USB cable. Your device will now play games and apps as if it's on Wi-Fi even if it's only on 3G.
Click to expand...
Click to collapse
Well, this whole text file thing didn't work for me. Do you have to be rooted for this to work?
It didn't work for me either and I'm rooted
Work for anyone
Did the above fix work for anyone?
.txt thing didn't work for me either and I'm rooted]
I am having a rooted phone with busybox and this text file trick doesn't work.
Sent from my GT-S5360 Gadget of Mass Destruction using xda-app
Using CWM........Busybox Commands........No I use my hands
I've been searching for a way to fool apps into thinking their on WiFi. No luck.
I hate to beat the dead horse but I switched from an iPhone to a HTC One and its turning out to be a bad deal. Your telling me all these yrs and no one has been able to make one of the most basic apps the iPhone can get via cydia yet.
We should start a bounty ...
I'll throw in 100 to start it off with.
omf05 said:
I've been searching for a way to fool apps into thinking their on WiFi. No luck.
I hate to beat the dead horse but I switched from an iPhone to a HTC One and its turning out to be a bad deal. Your telling me all these yrs and no one has been able to make one of the most basic apps the iPhone can get via cydia yet.
We should start a bounty ...
I'll throw in 100 to start it off with.
Click to expand...
Click to collapse
It's pretty pathetic really
I'll be abroad next week and wanted to catch a bit of the French Open Tennis but one of the TV apps I'm using requires a wifi connection. The fact there is no workaround yet is almost as idiotic as the morons who implement this "feature" in their apps.
Why should I care if someone is dumb enough to rinse their 1GB Data limit when I have unlimited 4G internet?
I asked about this in the Xposed forum, since it seems like an Xposed module might be the way to trick apps into thinking you're on wi-fi.
For me, the issue is with PdaNet+. I have unlimited data with T-Mobile, and I can pair my tablet via bluetooth and use my phone's data on my tablet. However, some apps don't work because they don't detect a data connection (ie: wi-fi), even though there is one. I can browse the internet. I can browse Google Play. But I can't download anything from Google Play, because it keeps waiting for a network connection. I can use Facebook, but I can't use the Facebook Messenger.
The work-around I can use at home is to use a virtual wi-fi router program on my laptop, connect my tablet to my laptop's wifi, and then connect my tablet via PdaNet+ bluetooth. Even there's no data going through the wi-fi, it still "tricks" my tablet into thinking there's a network connection, and it proceeds to download through bluetooth. Of course, this only works at home or if I have my laptop with me.
Yeah, I can always just tether my phone to my laptop and run my tablet off the laptop's virtual wi-fi router (which I typically do), but that's slower, and again, only works when my computer is with me.
Planterz said:
I asked about this in the Xposed forum, since it seems like an Xposed module might be the way to trick apps into thinking you're on wi-fi.
For me, the issue is with PdaNet+. I have unlimited data with T-Mobile, and I can pair my tablet via bluetooth and use my phone's data on my tablet. However, some apps don't work because they don't detect a data connection (ie: wi-fi), even though there is one. I can browse the internet. I can browse Google Play. But I can't download anything from Google Play, because it keeps waiting for a network connection. I can use Facebook, but I can't use the Facebook Messenger.
The work-around I can use at home is to use a virtual wi-fi router program on my laptop, connect my tablet to my laptop's wifi, and then connect my tablet via PdaNet+ bluetooth. Even there's no data going through the wi-fi, it still "tricks" my tablet into thinking there's a network connection, and it proceeds to download through bluetooth. Of course, this only works at home or if I have my laptop with me.
Yeah, I can always just tether my phone to my laptop and run my tablet off the laptop's virtual wi-fi router (which I typically do), but that's slower, and again, only works when my computer is with me.
Click to expand...
Click to collapse
Could you provide a little more detail in how to do this? What program are you using on your laptop? So the phone is running PDANet and then you connect it to your laptop via Bluetooth. Then after that you connect your tablet to the laptop's virtual wifi router?
Don't know if I understood completely but thanks in advance.
taino211 said:
Could you provide a little more detail in how to do this? What program are you using on your laptop? So the phone is running PDANet and then you connect it to your laptop via Bluetooth. Then after that you connect your tablet to the laptop's virtual wifi router?
Don't know if I understood completely but thanks in advance.
Click to expand...
Click to collapse
I have T-Mobile's Unlimited plan, which has unlimited data and 5gb free hotspot. My phone is a T-Mobile branded Samsung Galaxy Light SGH T399. On my phone I have PdaNet+ installed, with the full unlock key purchased ($8).
There's a free one to try, to make sure it works with your phone; whether it works or not depends on the phone itself, the version of Android it runs, and the provider from which you got it (if you didn't get an unlocked version). For example, a particular phone might work fine with T-Mobile, but the Sprint version of that phone might not. That's why there's the free version - to test before purchasing. The limitation with the free version is that it times out after about ~10 minutes and you have to reconnect.
PdaNet can connect to your computer in 3 ways. Wifi, Bluetooth, or USB tethering. Again, depending on your phone, carrier branding, and Android version, some methods may work while others won't.
Wifi works just like any wifi hotspot. However, depending on the afore mentioned conditions, wifi hotspot might not work the way you want it to. For example, on my T-Mobile branded Samsung Galaxy Light SGH-T399, using the wifi hotspot on PdaNet also loads up the pre-installed T-Mobile hotspot, which drains the 5gb mobile hotspot allotment. I haven't found a way to break that on this phone. On other phones (like Nexus devices), I know there are ways to only use your phone's data, and not the hotspot allotment, but frankly, these are very complicated and need a VPN subscription (ie: more money) to work. Wifi hotspot use is often broken anyway, depending on your carrier and Android version.
Bluetooth and USB tethering work differently than wi-fi, but otherwise work essentially the same way as each other. Both require a companion program to be installed onto your computer. A good idea is to keep a copy of this program on your phone, so you can install it on other people's computers if necessary (and perhaps the USB drivers for your phone as well).
I haven't messed around with Bluetooth much, because the Bluetooth on my laptop (via a dongle) is glitchy as $#@!, and I've never been able to get PdaNet to work with it properly except for a couple times which didn't last. Actually, I've never gotten anything to work properly with Bluetooth on my laptop, so this is probably just a problem with my computer/dongle/drivers, and YMMV. On the few times I've gotten PdaNet or other internet via Bluetooth (which some phones have built-in, and don't require PdaNet at all), speeds have been much, much slower, and I'd rather tether via USB anyway.
I connect my phone's internet to my laptop with USB tether. Make sure USB debugging is enabled, and plug it in. Make sure it's set as a Mass Storage device (4.1 or earlier), or as a Media Device (4.2+). Then on your phone, open PdaNet+ and Activate USB Tether (you can do this before plugging it in, it doesn't matter). On your computer, load PdaNet, and select Connect Internet (USB). If everything has been set up correctly, it should say "Connected", and you can now use your phone's internet on your computer.
Here's the important part:
If you don't have an Unlimited plan, tethering (via any method) will suck down your data. If you do have an unlimited plan, there's an option in PdaNet's settings (on your computer) to "Hide Tether Usage". This uses a proxy or VPN (not sure which) to fool your provider into thinking you're on your phone, and not on your computer. This works for me, with my phone, on T-Mobile. No guarantees that this will work with other phones, or other providers. Try the free version first, monitor your data usage (use your provider's account app, not the built-in Android one), and see if it works for you.
As for the virtual wifi network, there are a couple ways to do this. The PdaNet program for your computer actually has this built into it. Once you're connected, select the "WiFi Share" option, and it'll set up a wi-fi network that you (and others) can use on other devices, like other phones, tablets, computers smart-TVs, etc. Obviously, the computer you're tethered to needs to have wi-fi capability for this to work. But as long as you have a wi-fi modem, it can be turned into a wi-fi router with this option. It's not as strong as a real wi-fi router, but you don't have to buy and network a different piece of equipment either.
There are also stand-alone virtual wi-fi router programs. The one I've used mainly is Virtual Router Manager beta 0.9. A while ago, I tried a newer, non-beta version, but it was extremely unstable, so I went back to the 0.9 beta. I haven't tried any newer version in quite some time. I used this when I had proper internet (cable) in my apartment, but wanted to use wi-fi instead of my phone's data to do downloads or updates on my phone.
Neither the Virtual Router Manager or the WiFi Share option on PdaNet are 100% stable. Every once in a while, something glitches out, and I have to reboot my computer (I usually reboot my phone at the same time, just to be sure). But hey, apart from the $8 for PdaNet+, I get unlimited mobile and home internet for $80/month, so I can't complain.
To recap, I have my phone USB tethered to my laptop (which is plugged into a 42" HDTV) via PdaNet+. I use a virtual wi-fi router option to give wi-fi to my tablet. One internet connection, 3 devices connected.
My problem is that, even though I own a laptop, it practically never goes with my anywhere. It sits on a cooling pad, plugged into 2 external HDDs and my 42" HDTV, and I sit at my couch with a wireless mouse/keyboard. But when I'm away from my apartment, and I have my tablet, there's certain things I can't do on the tablet connected via PdaNet and Bluetooth, because it doesn't have a wi-fi connection, and these certain apps don't detect a network connection.
Planterz said:
I have T-Mobile's Unlimited plan, which has unlimited data and 5gb free hotspot. My phone is a T-Mobile branded Samsung Galaxy Light SGH T399. On my phone I have PdaNet+ installed, with the full unlock key purchased ($8).
There's a free one to try, to make sure it works with your phone; whether it works or not depends on the phone itself, the version of Android it runs, and the provider from which you got it (if you didn't get an unlocked version). For example, a particular phone might work fine with T-Mobile, but the Sprint version of that phone might not. That's why there's the free version - to test before purchasing. The limitation with the free version is that it times out after about ~10 minutes and you have to reconnect.
PdaNet can connect to your computer in 3 ways. Wifi, Bluetooth, or USB tethering. Again, depending on your phone, carrier branding, and Android version, some methods may work while others won't.
Wifi works just like any wifi hotspot. However, depending on the afore mentioned conditions, wifi hotspot might not work the way you want it to. For example, on my T-Mobile branded Samsung Galaxy Light SGH-T399, using the wifi hotspot on PdaNet also loads up the pre-installed T-Mobile hotspot, which drains the 5gb mobile hotspot allotment. I haven't found a way to break that on this phone. On other phones (like Nexus devices), I know there are ways to only use your phone's data, and not the hotspot allotment, but frankly, these are very complicated and need a VPN subscription (ie: more money) to work. Wifi hotspot use is often broken anyway, depending on your carrier and Android version.
Bluetooth and USB tethering work differently than wi-fi, but otherwise work essentially the same way as each other. Both require a companion program to be installed onto your computer. A good idea is to keep a copy of this program on your phone, so you can install it on other people's computers if necessary (and perhaps the USB drivers for your phone as well).
I haven't messed around with Bluetooth much, because the Bluetooth on my laptop (via a dongle) is glitchy as $#@!, and I've never been able to get PdaNet to work with it properly except for a couple times which didn't last. Actually, I've never gotten anything to work properly with Bluetooth on my laptop, so this is probably just a problem with my computer/dongle/drivers, and YMMV. On the few times I've gotten PdaNet or other internet via Bluetooth (which some phones have built-in, and don't require PdaNet at all), speeds have been much, much slower, and I'd rather tether via USB anyway.
I connect my phone's internet to my laptop with USB tether. Make sure USB debugging is enabled, and plug it in. Make sure it's set as a Mass Storage device (4.1 or earlier), or as a Media Device (4.2+). Then on your phone, open PdaNet+ and Activate USB Tether (you can do this before plugging it in, it doesn't matter). On your computer, load PdaNet, and select Connect Internet (USB). If everything has been set up correctly, it should say "Connected", and you can now use your phone's internet on your computer.
Here's the important part:
If you don't have an Unlimited plan, tethering (via any method) will suck down your data. If you do have an unlimited plan, there's an option in PdaNet's settings (on your computer) to "Hide Tether Usage". This uses a proxy or VPN (not sure which) to fool your provider into thinking you're on your phone, and not on your computer. This works for me, with my phone, on T-Mobile. No guarantees that this will work with other phones, or other providers. Try the free version first, monitor your data usage (use your provider's account app, not the built-in Android one), and see if it works for you.
As for the virtual wifi network, there are a couple ways to do this. The PdaNet program for your computer actually has this built into it. Once you're connected, select the "WiFi Share" option, and it'll set up a wi-fi network that you (and others) can use on other devices, like other phones, tablets, computers smart-TVs, etc. Obviously, the computer you're tethered to needs to have wi-fi capability for this to work. But as long as you have a wi-fi modem, it can be turned into a wi-fi router with this option. It's not as strong as a real wi-fi router, but you don't have to buy and network a different piece of equipment either.
There are also stand-alone virtual wi-fi router programs. The one I've used mainly is Virtual Router Manager beta 0.9. A while ago, I tried a newer, non-beta version, but it was extremely unstable, so I went back to the 0.9 beta. I haven't tried any newer version in quite some time. I used this when I had proper internet (cable) in my apartment, but wanted to use wi-fi instead of my phone's data to do downloads or updates on my phone.
Neither the Virtual Router Manager or the WiFi Share option on PdaNet are 100% stable. Every once in a while, something glitches out, and I have to reboot my computer (I usually reboot my phone at the same time, just to be sure). But hey, apart from the $8 for PdaNet+, I get unlimited mobile and home internet for $80/month, so I can't complain.
To recap, I have my phone USB tethered to my laptop (which is plugged into a 42" HDTV) via PdaNet+. I use a virtual wi-fi router option to give wi-fi to my tablet. One internet connection, 3 devices connected.
My problem is that, even though I own a laptop, it practically never goes with my anywhere. It sits on a cooling pad, plugged into 2 external HDDs and my 42" HDTV, and I sit at my couch with a wireless mouse/keyboard. But when I'm away from my apartment, and I have my tablet, there's certain things I can't do on the tablet connected via PdaNet and Bluetooth, because it doesn't have a wi-fi connection, and these certain apps don't detect a network connection.
Click to expand...
Click to collapse
Thanks for the great explanation! This helps quite a bit. I'll give this a shot to see how it goes.
Yes I bought the chromecast V2 but I could never believe this stupid limitation that you can use it only with wifi conection which means you need a secondary device to make this work.
I have a fast and reliable 4G speed so I have no need to invest in any wifi solution.
I hope this is a joke ? must be some way around it ? (without root)
blackinfinity said:
Yes I bought the chromecast V2 but I could never believe this stupid limitation that you can use it only with wifi conection which means you need a secondary device to make this work.
I have a fast and reliable 4G speed so I have no need to invest in any wifi solution.
I hope this is a joke ? must be some way around it ? (without root)
Click to expand...
Click to collapse
Have you tried guest mode? I think that should do what you want..
Sent from my Nexus 6P using Tapatalk
I use mine every day with only my phone's LTE signal through its hotspot. The trick is you have to use another phone to set up the chromecast to connect to it initially. You only need to do this one time to get the chromecasts's settings set properly, and then just turn hotspot on on your phone, chromecast will see it and connect every time.
I think the chromecast app is the only one that requires wifi on before it will even attempt to look for a receiver, because in my experience, streaming apps like netflix, hbo, youtube and comedy central dont consider what radio connects to where at all before the cast icon pops up.
Something else you can do to get that initial setup done is to connect it to another wifi AP with the SSID and WPA2 password set to whatever you want your phone's hotspot to use. Im pretty sure the chromecast only look at the network name and security (not MAC or anything like that) becasue ive done this a few times without issue.
syndre said:
I use mine every day with only my phone's LTE signal through its hotspot. The trick is you have to use another phone to set up the chromecast top connect to it. You only need to do this one time to get the chromecasts's settings set properly, and then just turn hotspot on on your phone, chromecast will see it and connect every time.
I think the chromecast app is the only one that requires wifi on before it will even attempt to look for a receiver, because in my experience, streaming apps like netflix, hbo, youtube and comedy central dont consider what radio connects to where at all before the cast icon pops up.
Click to expand...
Click to collapse
Oh my god ? is this really true ? so you say you only need a wifi network ONE time ? to setup the chromecast and then I can use it with wifispot on my smartphone ?
This sound beyond stupid to me.
The problem is I have no secondary device I can do this with and I got no wifi network to connect to.
Must be some way around this some how if you only need to d this one time
blackinfinity said:
Oh my god ? is this really true ? so you say you only need a wifi network ONE time ? to setup the chromecast and then I can use it with wifispot on my smartphone ?
This sound beyond stupid to me.
The problem is I have no secondary device I can do this with and I got no wifi network to connect to.
Must be some way around this some how if you only need to d this one time
Click to expand...
Click to collapse
That's what I'm saying.
The reason it doesn't work setting it up that first time is because that process involves both Chromecast and phone using the app fsetting it up to first connect directly to each other, then both connect to the same AP, then talk to each other again for through that network, WITH internet access at the same time. That's really hard to switch radios around fast enough (not impossible though) and still get it to accept and keep the settings for good
---------- Post added at 05:02 AM ---------- Previous post was at 04:53 AM ----------
Also, once you get it working, youll probanly want to use a laptop or something like that to be the device that you use to tell the Chromecast what to play... It works better that way, and you can to use your phone for other stuff while that's going on if you want. You can cast local media from a PC with way better results as well, using something like Plex or the Videostream plugin in Chrome
i am a little confused here, use another device to set up connection and then use your own device right after? how is that going to work if its two different connections?
I just got chromecast and have no WiFi or hot spot but could take to a place to set it up but when I got back home could I use it to mirror my phone screen
sarahlovestim420 said:
I just got chromecast and have no WiFi or hot spot but could take to a place to set it up but when I got back home could I use it to mirror my phone screen
Click to expand...
Click to collapse
get your phone to hotspot and connect that way. it doesn't need internet, just a active wifi network
I am also a bit confused. Could someone please spell it out step by step to idiots like me? Is there a link or YouTube video?
manc01 said:
I am also a bit confused. Could someone please spell it out step by step to idiots like me? Is there a link or YouTube video?
Click to expand...
Click to collapse
Are u needing help with the set-up process?
You need a 2nd local device to setup Chromecast.
1. Turn on cell phone hotspot (lets say name is Chase)
2. Connect 2nd device to Chase
3. Using 2nd device, setup your chromecast to connect to chase. TURN GUEST MODE ON
4. Once everything is set up and your chromecast is connected to Chase, you can use your smartphone running the hotspot to connect to the chromecast via the Pin. The 2nd device is no longer necessary.
Without something to connect the chromecast to the phone, I see no way to do it.
Side note, the pin feature can sometimes allow you to use your chromecast on hotel wifis that do not normally work.
---
OP, is there no where near you like a internet cafe, staples, library, anywhere that might have a computer with internet access with wifi? What about a smart phone shop like Verizon or Tmobile? Use one of their demo phones to do it.
Sent from my Pixel XL using Tapatalk
I have same issue like this. The only thing is I don't use a Chromecast. I hook up my TV with LAN (Old Sony Bravia) to my router and my phone to same routers WiFi. So I am able to share and connect with TV. No issues. I have a crappy wired internet connected to it. I also have unlimited 4G plan on my phone. I use AllConnect to cast from my Phone to TV. Now I am able to cast Movie HD app via AllConnect on my TV. But as soon as I disconnect the wired internet from my router. I am not able to cast. I want to use my Phones 4G internet to stream on my TV. Theoretically it should be possible to cast using my routers LAN which I am able to. But as soon as I disconnect DSL cable from my router the streaming stops. Can anyone help me here.
Another way
sarahlovestim420 said:
Are u needing help with the set-up process?
Click to expand...
Click to collapse
Hello
You can also spoof the MAC of the chromecast on your phone and configure the chromecast by this way.
However you need to have root access on your phone to install a software like Mac Changer.
This solution is very usefull in an hotel which require a connection to an open wifi network and a second authentification with login and password.
Regards