Related
This is my first review, so I hope it doesn't suck.
Both my wife and I have the Tilt 2. I decided to go with InvisibleShield while she wanted a case. After looking at all the comments here about cases not fitting, I decided to go with 2 different ones from Amazon. One fit horribly, so i wont even mention it.
She is using the Tilt2 Praetorian Slip and she loves it. Installation was a little tough as the fit is pretty precise. I suggest installing the top (screen) side first and then the bottom (keyboard). Install both with the KB extended. I have attached pics of the fit.
The only complaint I have (she thinks of it as a feature) is that the cover makes it a little more difficult to slide out the keyboard. She like it because it used to slide open in her purse (mostly because of the fact that she keeps it in an inside pocket of her purse which causes it to hit just right against crap she has in another pocket). Overall, this is a pretty nice cover. I am sure you can get it cheaper than amazon, but I had gift certificates to spend
Hope this helps!
Thanks for the review! I bought the same case a few months ago, although it was advertised as for the Verizon Touch Pro 2. I was unaware they made one for the Tilt 2. Now I won't have to worry about it falling off randomly!
thsi case probably wouldnt work with invisible shield on too huh
Doinshots said:
This is my first review, so I hope it doesn't suck.
Both my wife and I have the Tilt 2. I decided to go with InvisibleShield while she wanted a case. After looking at all the comments here about cases not fitting, I decided to go with 2 different ones from Amazon. One fit horribly, so i wont even mention it.
She is using the Tilt2 Praetorian Slip and she loves it. Installation was a little tough as the fit is pretty precise. I suggest installing the top (screen) side first and then the bottom (keyboard). Install both with the KB extended. I have attached pics of the fit.
The only complaint I have (she thinks of it as a feature) is that the cover makes it a little more difficult to slide out the keyboard. She like it because it used to slide open in her purse (mostly because of the fact that she keeps it in an inside pocket of her purse which causes it to hit just right against crap she has in another pocket). Overall, this is a pretty nice cover. I am sure you can get it cheaper than amazon, but I had gift certificates to spend
Hope this helps!
Click to expand...
Click to collapse
Neat.. glad yours fit. I ordered one for the Tilt2 from Amazon as well, and Boxwave sent one labeled 'Touch Pro 2'. I see yours doesn't have a cutout area for the PTT button either, do you have issues with that? My praetorian case would almost always trigger the PTT button whenever I handled the phone.
The top/screen portion of my Praetorian didn't fit right and opening and closing the top was almost impossible - even ended up ripping off the protective plastic along one side of the keyboard. (the protective plastic that is designed to be there, not the temporary stuff it whipped with) I can see just by looking at your pictures that your screen portion fits waay better than mine did.
When I contacted Boxwave about the issues, no questions asked and they sent a postage paid label for the return. I'd love to try this case again, as I did like the feel of it, but nervous about another no-fit. I went with BodyGuardz instead.. not sure I'm happy with those..
Thanks,
I´ll include it on the main thread
http://forum.xda-developers.com/showthread.php?t=524059
JJHiemenz said:
Neat.. glad yours fit. I ordered one for the Tilt2 from Amazon as well, and Boxwave sent one labeled 'Touch Pro 2'. I see yours doesn't have a cutout area for the PTT button either, do you have issues with that? My praetorian case would almost always trigger the PTT button whenever I handled the phone.
The top/screen portion of my Praetorian didn't fit right and opening and closing the top was almost impossible - even ended up ripping off the protective plastic along one side of the keyboard. (the protective plastic that is designed to be there, not the temporary stuff it whipped with) I can see just by looking at your pictures that your screen portion fits waay better than mine did.
When I contacted Boxwave about the issues, no questions asked and they sent a postage paid label for the return. I'd love to try this case again, as I did like the feel of it, but nervous about another no-fit. I went with BodyGuardz instead.. not sure I'm happy with those..
Click to expand...
Click to collapse
Man, sorry you had so many issues. The PTT button is indeed covered, but she has had no issues with it at all (hers is remapped to toggle bluetooth on and off). The fit on the screen portion is *very* tight. Took some effort to get it installed properly.
Also, mine definitely said "Tilt 2" on the packaging.
It is disappointing that it covers the PTT button. I assume your wife has abandoned that function (easily switching BT on/off)?
Thanks for posting reviews on this case -- I'm trying to decide what route to take to give my new Tilt 2 some added protection, and more importantly, cut down on the slickness/smudge magnet-ness of the shiny battery cover (which is my #1 gripe with the GSM TP2, both CDMA versions have rubberized covers which won't fit their GSM siblings due to the placement of the 3.5 mm jack).
I really wish someone made a rubberized battery cover to replace the shiny OEM one. These snap on type cases are okay, but they become a major pain as soon as you need to pop off the battery cover in order to flash a new ROM (as I do often), reset the device, or swap out memory cards. I worry trying to snap-in and pry off these cases frequently will damage the phone -- especially when it's a super snug fit. IMHO, a rubberized battery cover, along with perhaps the upper portion of this case to protect the chrome bezel from getting nicked would be an ideal solution! I may just go down to Home Depot this weekend and see if they have a spray that can rubberize plastic, then I might just buy a spare OEM battery cover and see if I can rubberize it.
sleze said:
It is disappointing that it covers the PTT button. I assume your wife has abandoned that function (easily switching BT on/off)?
Click to expand...
Click to collapse
Nope, the PTT button still works perfectly under the cover. Does not get accidentally pressed and is responsive when you push it.
azwildcat98 said:
Thanks for posting reviews on this case -- I'm trying to decide what route to take to give my new Tilt 2 some added protection, and more importantly, cut down on the slickness/smudge magnet-ness of the shiny battery cover (which is my #1 gripe with the GSM TP2, both CDMA versions have rubberized covers which won't fit their GSM siblings due to the placement of the 3.5 mm jack).
I really wish someone made a rubberized battery cover to replace the shiny OEM one. These snap on type cases are okay, but they become a major pain as soon as you need to pop off the battery cover in order to flash a new ROM (as I do often), reset the device, or swap out memory cards. I worry trying to snap-in and pry off these cases frequently will damage the phone -- especially when it's a super snug fit. IMHO, a rubberized battery cover, along with perhaps the upper portion of this case to protect the chrome bezel from getting nicked would be an ideal solution! I may just go down to Home Depot this weekend and see if they have a spray that can rubberize plastic, then I might just buy a spare OEM battery cover and see if I can rubberize it.
Click to expand...
Click to collapse
Sounds like skinning/shielding your phone with GadgetShieldz might be the way to go. The GadgetShieldz does take a little time to install but it works. The protective film on the screen is easy to install and bubble free. It makes the phone non-slippery. It would not protect the phone like a case but it does prevent scratches. When installed, it adds very little weight and dimension to the phone.
Actually, there are other protective films/shields but I only have experience with GadgetShieldZ. It might work for you.
Boxwave Praetorian Crystal Slip for Tilt 2
orb3000 said:
Thanks,
I´ll include it on the main thread
http://forum.xda-developers.com/showthread.php?t=524059
Click to expand...
Click to collapse
Just to report on this, I got one of these in the mail yesterday. So far I love it. It wasn't terribly difficult to get on. It fits very well too. My only real complaint is that it doesn't accommodate the PTT button that the Tilt 2 has right next to the volume buttons. It's not a big issue since I don't use PTT and the case doesn't prohibit using the key anyway.
Just be careful and make sure you order the one that specifically says it's for the Tilt 2. They make other models. I know they have the Praetorian on eBay but to be safe I opted to get mine directly from Boxwave. I got what I ordered too and could have used they're return policy if I needed.
Oh...I'll be happy to post pics if anyone wants but I think someone already put some up of this one a Tilt2.
azwildcat98 said:
Thanks for posting reviews on this case -- I'm trying to decide what route to take to give my new Tilt 2 some added protection, and more importantly, cut down on the slickness/smudge magnet-ness of the shiny battery cover (which is my #1 gripe with the GSM TP2, both CDMA versions have rubberized covers which won't fit their GSM siblings due to the placement of the 3.5 mm jack).
I really wish someone made a rubberized battery cover to replace the shiny OEM one. These snap on type cases are okay, but they become a major pain as soon as you need to pop off the battery cover in order to flash a new ROM (as I do often), reset the device, or swap out memory cards. I worry trying to snap-in and pry off these cases frequently will damage the phone -- especially when it's a super snug fit. IMHO, a rubberized battery cover, along with perhaps the upper portion of this case to protect the chrome bezel from getting nicked would be an ideal solution! I may just go down to Home Depot this weekend and see if they have a spray that can rubberize plastic, then I might just buy a spare OEM battery cover and see if I can rubberize it.
Click to expand...
Click to collapse
I wish I'd seen your post sooner! Home Depot and Lowe's does indeed have something like that. I'm sure lots of hardware stores do. It's called Plasti-Dip. I have a can right here You can buy it as spray-on or dip/brush-on applications. I use it on mountain bike parts and tools for extra grip. I'm not positive how well it will stick to a slick plastic surface but it is an option.
BluEyedTiger said:
Just to report on this, I got one of these in the mail yesterday. So far I love it. It wasn't terribly difficult to get on. It fits very well too. My only real complaint is that it doesn't accommodate the PTT button that the Tilt 2 has right next to the volume buttons. It's not a big issue since I don't use PTT and the case doesn't prohibit using the key anyway.
Just be careful and make sure you order the one that specifically says it's for the Tilt 2. They make other models. I know they have the Praetorian on eBay but to be safe I opted to get mine directly from Boxwave. I got what I ordered too and could have used they're return policy if I needed.
Oh...I'll be happy to post pics if anyone wants but I think someone already put some up of this one a Tilt2.
Click to expand...
Click to collapse
Hey man, I'm thinking about ordering this case and I wanted to see if you still like it and how it has held up over the past month. Thanks.
BehindTheLight said:
Hey man, I'm thinking about ordering this case and I wanted to see if you still like it and how it has held up over the past month. Thanks.
Click to expand...
Click to collapse
I ordered one from BoxWave and I think I'm still going to shop around for something else. It seems like the Tilt2 has less options than the other variations of the Rhodium so people may just be settling for this due to "Slim Pickin's."
I like the way the gel gives more texture and grip to the phone, but I still feel uneasy because it's definitely not a snug fit. The part that covers the screen section of the phone is very flimsy and after you get it on, you want to keep checking it to make sure that it is attached; it feels like it can easily slip off at any time. This is specifically evident when you slide your screen up and tilt it. Tap the top right, or the middle section that really has no grip around the phone, and it might just pop off...
I still have it on my phone because it is the lesser of two evils, have something vs. not having something, but are there any other options for the Tilt2?
BehindTheLight said:
Hey man, I'm thinking about ordering this case and I wanted to see if you still like it and how it has held up over the past month. Thanks.
Click to expand...
Click to collapse
It's held up quiet nice...even with as much flashing I do (have to remove the bottom piece every time). I've figured out a great way to put it back on that's really fast and easy. Some people say it's difficult to get on. I think the top piece is the hard part but I've taken it off a few times and have no issues there either. It still fits good. If I remember, next time I take it off I'll shoot some pics of how I put it on and upload them.
Learic said:
I ordered one from BoxWave and I think I'm still going to shop around for something else. It seems like the Tilt2 has less options than the other variations of the Rhodium so people may just be settling for this due to "Slim Pickin's."
I like the way the gel gives more texture and grip to the phone, but I still feel uneasy because it's definitely not a snug fit. The part that covers the screen section of the phone is very flimsy and after you get it on, you want to keep checking it to make sure that it is attached; it feels like it can easily slip off at any time. This is specifically evident when you slide your screen up and tilt it. Tap the top right, or the middle section that really has no grip around the phone, and it might just pop off...
I still have it on my phone because it is the lesser of two evils, have something vs. not having something, but are there any other options for the Tilt2?
Click to expand...
Click to collapse
I haven't really had any trouble with mine popping off. It took a bit to get the top on right and it was a pretty snug fit too. Getting the corner edges all the way tucked under was the hardest part. I'm guessing it's a manufacturing thing. Some say it's a tight fit and other say it's loose. I will agree that the sides on the top piece are flimsy because they're not attached the the phone but if they were it would probably make matters worse by either rubbing against the bottom piece or creating too big of a gap between the two parts of the phone.
I agree there aren't many options for the Tilt 2 and I hate to say it but there probably won't be.
BluEyedTiger said:
I haven't really had any trouble with mine popping off. It took a bit to get the top on right and it was a pretty snug fit too. Getting the corner edges all the way tucked under was the hardest part. I'm guessing it's a manufacturing thing. Some say it's a tight fit and other say it's loose. I will agree that the sides on the top piece are flimsy because they're not attached the the phone but if they were it would probably make matters worse by either rubbing against the bottom piece or creating too big of a gap between the two parts of the phone.
I agree there aren't many options for the Tilt 2 and I hate to say it but there probably won't be.
Click to expand...
Click to collapse
If yours is a snug fit, I wonder if we received the same thing! Did you order from BoxWave? I have a little plastic tool that I used to get the corners onto the top half quickly which was actually made to fit into the creavice of a HTC Dash phone to pop the clips and take the phone apart. It works great and I can see the little flaps around the corner so you can tell the corners of the phone are between the gel lips.. It's still too easy to come off though..
Even though my receipt says "Praetorian Crystal Slip, HTC Tilt2, Smoke Grey - SKU: bw-268-3729-2808", it also says "ITEM: HTC TOUCH PRO2." The Box also has a white sticker in the top right that says "Praetorian Crystal Slip - TOUCH PRO2."
Do you remember if yours said the same? Maybe they somehow shipped me the wrong one?
Learic said:
If yours is a snug fit, I wonder if we received the same thing! Did you order from BoxWave? I have a little plastic tool that I used to get the corners onto the top half quickly which was actually made to fit into the creavice of a HTC Dash phone to pop the clips and take the phone apart. It works great and I can see the little flaps around the corner so you can tell the corners of the phone are between the gel lips.. It's still too easy to come off though..
Even though my receipt says "Praetorian Crystal Slip, HTC Tilt2, Smoke Grey - SKU: bw-268-3729-2808", it also says "ITEM: HTC TOUCH PRO2." The Box also has a white sticker in the top right that says "Praetorian Crystal Slip - TOUCH PRO2."
Do you remember if yours said the same? Maybe they somehow shipped me the wrong one?
Click to expand...
Click to collapse
Yeah I got mine directly from boxwave. They have like 3 different models of that slip. Most of the adds I saw on Amazon and eBay claimed it would fit on 3 or 4 different TP2 models which I knew it wouldn't. I emailed boxwave about the pics in their online catalog because it didn't look like a Tilt 2 to me and they admitted it wasn't. They said they didn't have one for the pics. Which made sense I mean why spend that much just to get pics but they promised it would fit so I figured what the hell. The hard covers kinda suck.
Thanks for the replies, I guess I will go ahead and order it and see what happens.
I just got the unbranded version of this case off ebay (the seller's id was e-story).
It's not too bad on my unbranded TP2. It's slightly more difficult to slide out the keyboard, and when the screen is fully tilted, the top row of keys are slightly obscured, but nothing too major in my opinion.
I like that the case improves the grip of the phone, but I'm also rather concerned that the case will eventually melt under hotter conditions since the material feels rather gummy.
I bought one of these for my dad: http://www.amazon.com/gp/product/B005KK9C7C
Terrible case. It was nearly 40 dollars, and it's just about the worst way to spend that much money. I wrote a review (only review) on amazon:
I ordered this case a week ago. It just came in today due to some difficulty with USPS, not Amazon's fault. I opened the packaging, and it was clear that it was a cheap product. It comes in a simple small box, something you would expect from a Chinese ripoff. The leather material is of ok quality. It doesn't scratch, and it is a nice color. However, the actual plastic which holds the phone is cheap, and mine came with a few chips on the edges. It feels like the phone could fall out any minute. The hold is not secure at all. The design of the case is overall terrible. The credit card slots won't expand, so putting more than one card in each slot is nearly impossible. The extendable flap is too loose, and often extends while in my pocket, allowing my pocket contents to come in contact with the phone's screen. Finally, the worst draw back is charging. I have to open the case entirely (flip it open) to charge the phone. The charging slot is at the bottom of the phone, and the case is made so the credit card holding section flips from the bottom to the top. This means there is a strip of leather blocking the charging port. Un-doing the button flap won't fix it, you have to completely expose the screen the charge the phone.
Click to expand...
Click to collapse
So if anyone was thinking of buying this case: don't.
My dad still needs a new case. He insists on one of these types of cases. I've never used one, and I've looked at the normal companies, haven't found anything good. Does anyone know of one?
I had an amazon gift card to use up, and we're planning a road trip to a waterpark so I decided to use the gift card to try and find a waterproof/water-resistant solution for my lte. I wasn't going swimming with these, but I did want to protect my phone from the the occasional dunk or splash, and I didn't trust a ziplock bag to do the job. I also didn't want to spend a lot (otherwise I would have gotten the overboard case).
I ended up ordering the following cases;
BestDealUSA Waterproof Underwater Pouch Dry Bag Pack Case Cover for Cell Phone PDA Blue - $2.96
Waterproof Case for Apple iPhone 4, 4S - Also Works with iPod Touch, iPhone 3G, 3GS, & Other Smartphones - IPX8 Certified to 100 Feet - $4.57
Universal Waterproof Bag Case for Cell Phone / PDA, Blue - $0.01
Universal Waterproof Bag Case for Cell Phone / PDA, Black - $1.92
BestDealUSA Waterproof Underwater Pouch Dry Bag Pack Case Cover for Cell Phone PDA Blue
The plastic material seems strong on this case, and the seal seems like it would do a good job to keep the moisture out. The evo slides in and out easily, even with a tpu case, although it does it need to go in upside down if you want to take pictures - otherwise the camera is blocked by the opaque section of plastic, but this is not a big deal. There is a raised seal around the window of clear plastic (which takes up about 4/5ths of the phone screen) that makes pulling the unlock ring a little difficult, but not impossible. This is the biggest of the cases, with the most space around the phone. Screen responsiveness through the plastic is good, and the the window is clear, so its easy to see the phone screen. Lanyard runs through the width of the case, and seems very strong - I don't see it snapping or anything.
Waterproof Case for Apple iPhone 4, 4S - Also Works with iPod Touch, iPhone 3G, 3GS, & Other Smartphones - IPX8 Certified to 100 Feet
This one looks very similar to the higher priced overboard case and has great reviews. The areas surrounding the clear windows are puffy, as if it would allow the case to float. Unlike the other cases (which use a combination of two ziplock-type closure zips), this one has a plastic mechanical mechanism to squeeze and hold the opening shut like a vise. I don't know if I would trust this case to remain underwater for any length of time. It doesn't seem to seal as well as I would like, although the reviews all rave about how watertight it is. Having said that, the phone fits in this case perfectly with the tpu case, and even better without a case (upside down again), without being too snug, and the clear windows are exactly the size of the phone screen - only the capacitive buttons are hidden. Screen responsiveness through the plastic is good, and the the window is clear, so its easy to see the phone screen. The puffy areas around the clear screen also do a really good job of holding the phone in place, but makes it a bit difficult to press the power button. The lanyard that this case with end in what appears to be a thread that you loop through an opening in the case and seems like a good tug would snap it off.
Universal Waterproof Bag Case for Cell Phone / PDA, Black/Blue
I was only going to get the black one, but when I saw the blue one for a penny, I decided why not. These are identical cases, but one is black, and one is blue. These are the snuggest cases, and its a challenge to get the phone in, even without the tpu case. The plastic material the cases are made of is very tacky on the inside, so the phone tends to get stuck when you put it in or take it out. The plastic also seems thinner on these than the other cases, and the seals around the edge don't seem very reliable. Once the phone is in though, it's the most compact and pocketable of all of the cases. These cases do not have a clear window on both sides, so if you want to use the camera, then the phone screen will be covered by the translucent side of the case. It's not too bad, and the screen is still visible, but in bright situations, this could be an issue. Having said that, screen responsiveness is very good with these cases, most likely due to the thinness of the plastic. Lanyard goes through hole in the case and seems strong enough. These also come with an arm band that may fit you if you have the arms of a small child. They're really, really small.
Final thoughts - All of these would probably do a good job to keep water and moisture off of the phone (or even sand if you're going to the beach), and I think any of them would be fine to protect against accidental splashing. If I was going diving or swimming with my phone, I would probably shell out the extra cash for the overboard, or at least do some serious waterproof testing on these first. As it stands, I think I'll end up using the first case - Not too crazy about the blue, but I think it will do the best job of keeping the phone dry, and I won't need to worry about going down the log flume with it in my pocket or around my neck (like a tourist, lol).
Hey man, thanks for the reviews. I didn't even know you could get waterproof cases/bags so cheap.
I'll have to pick one up now.
I do suggest you update the prices in your post to include the shipping though for a better cost comparison (even though the difference here is minimal). So many venders inflate the shipping to make up the difference for a $0.01 item.
p.s. I'm going to pick up the first one as well since it looks like I can easily have it in my pocket as a just in case. (I'm in Florida and we have crazy torrential thunderstorms out of no where, so if I'm out jogging, I can have it in my pocket just in case.
Though expensive, Lifeproof cases are really nice. Ive known many people to go out in the ocean and take pictures under water with them.
Just an update, I did end up using that first case, and although it never went underwater, it got splashed on alot. Phone stayed dry, it fit great in the bathing suit pocket, and even took some great pics through the case. Would definitely recommend.
Quick update from me too. I ended up ordering this case: http://www.amazon.com/gp/product/B0058NXWPY/ref=oh_details_o02_s00_i00
Used on a canoe trip. The canoe flipped and it went underwater for around a minute or so, and air dried after, did a great job. Would recommend this one!
i am using the first case, blue, as well. Works fine, keeps my phone dry in a 10ft deep pool. Takes picture fine too. Thanks for the review OP.
I actually prefer these right here. They come in different sizes I prefer the 6-1/2 x 3-1/4I can't confirm they work in 100 ft of water because I have no reason to be that deep ever in my life, but for the average rainy day, screwing around by the pool or working out these work great. The best part is the patented purple zip technology that lets you visibly confirm the case is sealed. Also pics turn out great. Good luck in your decision
Asadullah said:
I actually prefer these right here. They come in different sizes I prefer the 6-1/2 x 3-1/4I can't confirm they work in 100 ft of water because I have no reason to be that deep ever in my life, but for the average rainy day, screwing around by the pool or working out these work great. The best part is the patented purple zip technology that lets you visibly confirm the case is sealed. Also pics turn out great. Good luck in your decision
Click to expand...
Click to collapse
Hahaha that had me laughing so much once I read the whole thing then clicked on the link. Good one!
Sent from my EVO using xda premium
Just purchased an s - view cover of eBay and it says that it has an authentication chip in it so it will actually work like the original.
Just thought I would share this with everyone.
here's the link: http://www.ebay.com.au/itm/321261135549
Hope it works
Sent from Samsung Galaxy Note 3. checkout www.techenthu.com.
If you like my post hit thanks
I've bought one from ebay:
ebay.co.uk/itm/380780764369
And I don't like it to be honest.
First of all, the finish is bad. You can see bits of broken fabrics on the edge of S-view windows.
The ear piece was not properly cut. There were still bits of fabrics in the ear piece that I had to pull them out.
There were a few scratches (probably there when I received it) on the s-view window. Those scratches were behind the cover.
Perhaps worst of all, the S-view function is kind of buggy. Whenever I connect it to the charger, it has a 75% chance to knock the S-view out like the chip suddenly disappeared. Evens if I never connect to a charger, there's still a chance... say 1 - 5 % that the S-View function suddenly disappear.
I certainly hopes the one you get is better than mine. Anyway, I decided to go for the original S-view + wireless because:
1. I don't like the chip in the wireless receiver constantly press onto the battery. I can feel there's a slight square dent on the battery after a week of usage
2. I don't want to gamble on the quality any more.
P.S: The Note 3 Basesu Case can be pretty good. But I wanted wireless charging as well and I'm not in the mood to carry out such modification =P
vandals01 said:
I've bought one from ebay:
ebay.co.uk/itm/380780764369
And I don't like it to be honest.
First of all, the finish is bad. You can see bits of broken fabrics on the edge of S-view windows.
The ear piece was not properly cut. There were still bits of fabrics in the ear piece that I had to pull them out.
There were a few scratches (probably there when I received it) on the s-view window. Those scratches were behind the cover.
Perhaps worst of all, the S-view function is kind of buggy. Whenever I connect it to the charger, it has a 75% chance to knock the S-view out like the chip suddenly disappeared. Evens if I never connect to a charger, there's still a chance... say 1 - 5 % that the S-View function suddenly disappear.
I certainly hopes the one you get is better than mine. Anyway, I decided to go for the original S-view + wireless because:
1. I don't like the chip in the wireless receiver constantly press onto the battery. I can feel there's a slight square dent on the battery after a week of usage
2. I don't want to gamble on the quality any more.
P.S: The Note 3 Basesu Case can be pretty good. But I wanted wireless charging as well and I'm not in the mood to carry out such modification =P
Click to expand...
Click to collapse
That sounds like a horrible case I'm really hoping I get a decent one. Thanks
I got one from ebay as well, but the seller isn't selling them anymore.
Thing is super buggy and somehow even messed with my bluetooth.
It would never remember setting the s-view background.
When flipped over to the back, it would activate s-view functions.
Bluetooth streaming would break up, hang, skip and pop.
I removed the case, and everything went back to normal.
Oh well
I read that scratched screen from him, is it true?
The ZeroLemon S20+ battery case is not for everyone. In order to fit 8,000 mAh of extra reserve battery power into a phone case, one has to accept the many compromises, such as the extra thickness, extra weight, more difficulty operating the phone with just one hand, and finding a more suitable place to carry the phone with you when going out. For longtime users of battery cases, none of these are dealbreakers. It's just something you expect and accept for being able to extend the battery life of your phone by days.
_____
*Pros:
-Great amount of extra battery life, good for gaming, heavy GPS navigation, and continuous video and photo-taking.
-Grippy and soft case.
-Mostly compatible with my Whitestone Dome TGSP.
-Easy to slip in and slip out.
-Wireless charging still works.
-Doesn't dampen speaker quality.
_____
*Neutral:
-Pushes up on the bottom-right corner of my TGSP.
_____
*Cons:
-None (for a battery case).
In my case, I've been using ZeroLemon battery cases for such a long time (Note 10, S10+, S9+, S8+, S7), I'm cool with all the compromises. Besides, I don't use the case all the time, every day. I only need it for those occasions when I'm going to somewhere where I know I'll be taking lots of pictures and videos, such as amusement parks and fairs. I also use it when I'm playing emulation games on the phone with a Bluetooth gamepad paired up.
As has been the case for a couple of years now, I'm happy to report that ZeroLemon continues to refine and improve the design and build quality of their battery cases year after year. The S20+ battery case is composed of two types of materials - a high density matte-black TPU component that makes up the top, bottom, sides, and camera lens portion of the case, and a smooth, grippy, matte-black portion that wraps around the battery on the back of the case. Both material types feel good in the hands, and any smudges or oils left on top can easily be wiped away.
https://drive.google.com/open?id=1dEQd8zCcMIQmP2r7m5ExQUtyLngYtuUv
https://drive.google.com/open?id=1uOqej18pH-Jfh9whheuuaccp2HmHfr0f
https://drive.google.com/open?id=1ntGVVhIZaM0xxUC8qP4Td4baY3Qlspi9
https://drive.google.com/open?id=1BnvF06pKJ41z-YgmLbZ6yYyLBdQAqNlD
All the buttons and holes lined up perfectly, and there was no decrease in speaker quality. Button presses do require extra effort, with the power button requiring more pressure compared to the volume up and volume down buttons. As a result, it took me a while to get used to taking screenshots on the phone. The battery case button on the back of the case is very clickity and responsive. A single click will activate the battery, and a 3-second hold will turn it off. Can't get simpler than that.
To my pleasant surprise, wireless charging worked just fine through the thick case. The phone doesn't get Fast Charged but it's definitely better than having to take out the phone from the case first.
https://drive.google.com/open?id=1_hBlNwIyCeSY6QDvt8jAlEtupd_CwNpC
https://drive.google.com/open?id=1pUv8CigN7aKjPUnSAwv8wbewCCQ7bUha
When charging the phone normally from the battery case, it also operates in a non-Fast Charge way. Having Qualcomm Fast Charge would've been nice but since this isn't a powerbank that I want to disconnect from as soon as possible, it's not a big deal to me.
Having a glass screen protector is a MUST for me, and I'm very happy to report that the case is 95% compatible with my Whitestone Dome Glass. As you can see from my pictures, the case doesn't make contact with the glass on the top and the sides, causing no lifting. The bottom of the case, however, does make slight contact. Fortunately, that hasn't resulted in air bubbles forming but it did introduce a squiggly line on the bottom-right corner of my screen protector. That has been slightly annoying but on the positive side, I can't see the line when the screen is turned on and lit up. When I take the phone out of the case, the squiggly line disappeared.
https://drive.google.com/open?id=1xR9AqVKd-Rede6Ebm-gsUub6z1BkA3FC
https://drive.google.com/open?id=1Roztxhsn1nKExAHLK9nrq71iIW4OhtBM
https://drive.google.com/open?id=1Un1AtTqZIy9yyMsQew-Hto2KdNswmv1c
https://drive.google.com/open?id=1Snin_kR7prXTY26EW6d1mGV7usvIenOn
https://drive.google.com/open?id=1l4vRzf8AtC01kN9hbPozMi597oyGfrIz
All in all, I'm quite happy with the ZL S20+ battery case. It might be unabashedly thick and bulky, but it provides a peace of mind that I can get through hours of gameplay or heavy use of the camera without getting all antsy and nervous. Being able to do wireless charging is awesome, and I'm happy that there is no compromise to the speaker quality this time around. For their future battery cases, I wish ZeroLemon would make the bottom lip of the case a bit thinner in order to avoid contacting a glass screen protector. 9.5 out of 10.
Good review except it leaves out the most important part - the battery life lol
Thanks for your review, I too have just purchased both the case and protector and very happy indeed with it.
I had bought one of these for a previous device. After 4 months, it started to fail, refused to hold a charge, just started to not work. I contacted the manufacturer, and their response was not only surprising in their candidness but sad that they were selling them knowing this:
The case is meant to only last at a maximum of 6-8 months. They KNOW these cases don't work after that and stated it quite clearly in their response to me.
Since then, I've avoided this manufacturer of "battery" cases.
Nice
Zerolemon actually told me that the life expectancy of these batteries is about 6 months. What exactly is the point of carrying around what essentially is a massive case attached to the device then if it only lasts 6 months?