I have the LTE version of galaxy s4, who is called i9506, and need special ROMs because of the 4G+.
I can't get any version to work, there is none marked as stable and I have installed CM11 version and gapps. During startup it says "kernel is not seandroid enforcing", then starts up the CM11 boot logo, but it loops forever, I left it over night but no success.
Related
I was running CyanogenMod 10.1 on my GT-I9300 for several months and it worked great. But the other day I was using Google Navigation as a sat nav while driving and the battery went to 1% and the phone froze. Tried hard Reset ect but ended up having to remove the battery to turn it off.
When I had charged the phone I was stook at the Samsung Galaxy S logo screen and would not boot. I tried everything and several roms to get my phone back in working order.
For some strange reason I can only install CyanogenMod 9, which the wifi and mobile does not work at all so its of no use. When trying the CM10 builds I get stook at the same screen and if I use a Stock ROM I get stook at the Samsung blue animation logo in a boot loop.
Any help would be deeply appreciated.
Tried a couple of other roms installing through Clockwork Mod, including Phenom but only the CM9 one works.
Also just tried the KIES firmware installation, installed fine but on first boot its back into loop
@asc197
I've been following you for a while since you started developing for samsung galaxy s6 edge from v1 to v8.0
I have a samsung galaxy s6 edge 925F with baseband G925FXXU3C019.
Ever since from v7 to v8 when using the 5 reboot menu and reboot the phone or hot reboot i get in the top left hand corner Kernel is not Seandroid Enforcing yet the animations boot and sound works fine and phone runs fine but the battery runs down quicker even though i have enabled google plays service "quick battery fix"
Any ideas what happened?
i have updated the modem today yet the kernal is still an issue from the ota
xxmcvapourxx said:
@asc197
I've been following you for a while since you started developing for samsung galaxy s6 edge from v1 to v8.0
I have a samsung galaxy s6 edge 925F with baseband G925FXXU3C019.
Ever since from v7 to v8 when using the 5 reboot menu and reboot the phone or hot reboot i get in the top left hand corner Kernel is not Seandroid Enforcing yet the animations boot and sound works fine and phone runs fine but the battery runs down quicker even though i have enabled google plays service "quick battery fix"
Any ideas what happened?
i have updated the modem today yet the kernal is still an issue from the ota
Click to expand...
Click to collapse
Download a stock firmware, and flash it via Odin.
Downloaded newer version of the Imperium rom and installed it successfully after i setup the google username and password install some softwares then rebooted the phone i am now stuck into the samsung galaxy s4 logo and no more movements at all for several minutes. tried several times still the same tried full wipe again installed version 9.1 now same story allowed me to boot first time then after that i reboot and the stuck to samsung glaxy s4 logo stuck again any idea what is happening?
Any one
shertech28 said:
Downloaded newer version of the Imperium rom and installed it successfully after i setup the google username and password install some softwares then rebooted the phone i am now stuck into the samsung galaxy s4 logo and no more movements at all for several minutes. tried several times still the same tried full wipe again installed version 9.1 now same story allowed me to boot first time then after that i reboot and the stuck to samsung glaxy s4 logo stuck again any idea what is happening?
Click to expand...
Click to collapse
Any one wanna answer this question?
Hey,
I'm using a Samsung Galaxy S3 LTE (i9305) at the moment, on which I tried to install TWRP and CM13.
At first the installation of TWRP did not work - after that, the SIM card didn't work as the cellphone made a restart into the system.
After a little bit of research (and a few videos on YouTube) I managed to install TWRP and installed CM 1 3 (unofficial) on my phone.
After a restart my phone was stuck in bootloop - the CM logo was only shown at the start and did move.
I made a factory reset after that and tried to install TWRP again, this time with CM 11 (official) - with the same problems as before.
After I installed CM 11, Windows shortly recognized the phone when it booted - but I don't know, if my PC would have recognized the others too (Windows just played the sound it does, when a new device is connected)
The TWRP version is 3.0.2-1.
Any idea what I could try now?
Thanks in advance!
Hello guys, I'm not completely new to custom ROMs and flashing,but when I tried to flash my galaxy prime SM-G530H(fortuna3G-kitkat) I stumbled across some trouble.
Note that my device is rooted.
First of all when I started with flashing TWRP custom recovery mode, my phone began showing "seandroid is not enforcing" when I open it ,but it still works.
I didn't give much attention to that issue and continued to flashing the custom ROM,which is lineageOS 13 (unofficial)
The ROM worked perfectly except for some slight problems.
My phone lost the ability to enter to sleeping mode.
Whenever I tap on the lock button,instead of the screen turning of it shows a white screen.
And the brightness is unadjustable always at its highest.
I tried flashing the ROM twice (with twrp) but the problem is still there, and also "seandroid not enforcing" is still there when I boost the phone.
Any ideas on how to deal with this issue without having to return to stock rom?