[Q] s3 pit problem - Galaxy S III Q&A, Help & Troubleshooting

Hi folks,
Yesterday, my phone goes to a state that only displays "Samsung Galaxy S III" on it. I rebooted it several times but nothing changes. I could not change it to recovery mode. At home, I try firmware initialisation through Kies, however it gives error and stops (no code is given at the end). Then I try to install a custum ROM through heimdall, however it gives error "failed to receive PIT file size, failed to download PIT file".
Then I test Odin with s3 pit file and re-partition option. If I add "nand erase all" option, it immediately gives write error. If I uncheck nand erase all, with version 3.10 it waits at "setup connection", with version 3.7 it waits at "get pit for mapping".
When I run heimdall with print-pit option, I have some messages (Manufacturer SAMSUNG, Product "Gadget Serial", etc.) then it gives:
ERROR: Failed to unpack received packet.
ERROR: FAiled to receive PIT file size!
ERROR: Failed to download PIT file!
Ending session...
then prints the following line several times:
ERROR: libusb error -7 whilst sending packet. Retrying...
finally
ERROR: Failed to send end session packet!
Releasing device interface...
What I want to ask is my phone dead? Is it possible to apply an operation to install new firmware and make it working?
Thanks for your support!

Any help? I will really appreciate it, thanks.

beaglest said:
Any help? I will really appreciate it, thanks.
Click to expand...
Click to collapse
Try this
http://forum.xda-developers.com/showpost.php?p=30087735

Related

[Q] Phone bricked itself overnight and Re-Partition operation failed.

Upon waking up this morning, I found that my phone was stuck on the (very first) Samsung logo. Before going to sleep, I was already booted and everything was stable.
I attempted to enter CWM recovery, but it would not work. It would continue restarting to show the Samsung logo.
Entering download mode, I see the following -
Product name:
Custom Binary Download: No
Current Binary: Samsung Official
System Status: Custom
This is strange, and pretty wrong. My product name is empty, custom binary download is "No" instead of at least "3" (I never have used TriangleAway), and I wasn’t using an official Samsung ROM before the problem.
If I attempt to flash a full stock, multi-part .tar.md5 file in PDA, ODIN v3.04 shows a "There is no PIT partition." error and fails. Re-partition is not ticked.
Therefore, I’ve tried to flash each of the following, with re-partition ticked:
GT-I9300_mx_20120220.pit
GT-I9300_mx_20120322.pit
GT-I9300_mx_20120329.pit
Each of them fail with a "Re-Partition operation failed." error.
If I try to flash a .pit file and the full .tar.md5, I get the same "Re-Partition operation failed." error.
Once a flash fails, I need to turn my phone off and on into download mode again, or else ODIN will stop.
The same thing happens for both ODIN v1.85 and v3.04, I’ve taken my battery in and out, I’ve tried this on two different computers, I’ve used every USB port, my Samsung drivers are up to date and Kies it not running in the background.
Maybe Your phone made a suicide, look on this thread:
http://forum.xda-developers.com/showthread.php?t=1993044
Similiar sympthomes, on mornig phone is dead and the PIT is unavaliable.

[Q] Trying to install CM 10.1. Heimdall giving me ERROR: Claiming interface failed!

Hey there. I'm following the official guide to installing CM 10.1 on my S3.
When I execute heimdall flash --recovery recovery.img --no-reboot
I get ERROR: Claiming interface failed!
Anyone know what is wrong? I've searched the forums and google.. All of the answers are non conclusive. One says to install 32 bit version of heimdall which did not work.
Also my phone is now in download mode after I installed a zadig.exe driver. What should I do if this keeps failing? Just turn the phone off?

Need help Galaxy note 2

Went to do the Adam Outler "casual" everything went well and was succesfull untill the end then the following occured.
uploading recovery 100%
ERROR failed to confirm end of file transfer sequence!
ERROR recovery upload failed!
ending session....
ERROR failed to send end of session packet
releasing device interface....
done
now my phone will not boot just flashes galaxy note 2 on the screen. Am i screwed?

[Q] Heimdall issues...

Im getting the error: ERROR: libusb error 0 whilst receiving packet. Retrying...
while trying to flash recovery in linux. Device is detected successfully but when i try to flash anything i get that error. Any idea?
mattish.91 said:
Im getting the error: ERROR: libusb error 0 whilst receiving packet. Retrying...
while trying to flash recovery in linux. Device is detected successfully but when i try to flash anything i get that error. Any idea?
Click to expand...
Click to collapse
Try reinstaling Heimdall and using a different usb cable.
Tried both, it did how ever work for galaxy mega, but not i9300.

Please Help !

After using Smart Switch Emergency Software Initialization, My S6 Edge Bootloops and goes into Recovery Mode Automatically and this error is written at the end
"dm-verity verification failed...
Need to check DRK first..."
I tried many things and when I try flashing a Kernel through Odin it gives me an error saying "Complete(Write) Operation Failed". Please Help Me.

Categories

Resources