Related
Thanks to our friends in Indonesia, we have the updated 2.2.2 Rom --> odienas and tri_zet
This update has been confirmed to work with:
S7-103, Indonesian version with dual cameras internal/external sdcard
S7-104, US BestBuy/RadioShack version with dual cameras and internal/external sdcard
S7-105, Australian version with dual cameras and external sdcard
Partially working:
S7-101, Austria Mobilkom version - loses camera, GPS?
S7-103, New Zealand - loses GPS?
More Info go ---> http://www.androidtablets.net/forum...d-2-2-2-dual-camera-s7-s7v100r001c98b021.html
Download
http://www.megaupload.com/?d=PVWGU020
http://www.mediafire.com/?9l52jhbl7b09czp
MD5 checksum for updata.app : 74D031FD717D8BF68956EF3F044C8EEB
Update install process:
1. unrar the file, and copy the 'dload' folder to the root directory of a sufficiently large external SDcard formatted to FAT/FAT32 (readable by the S7)
2. turn off the unit, and ensure that you are either plugged in with a battery inside the unit, or that you have enough charge left in your battery
3. turn on, and a progress bar will appear in the middle of the screen. Wait until "OK" is displayed on the screen.
4. turn off the unit by removing the battery and any powerplugs to the S7
5. repeat steps 2,3,4 again. otherwise it will hang at boot screen (instructed by Huawei)
6. Remove the SD card and start the device. If you wish the use the card for the device, remove the firmware files from the SD card before reinserting it.
If the update fails to install, check that your file was properly moved into the SDcard by comparing the MD5 checksum.
The overall process should take less than 15 minutes to complete.
Adobe Flash is not pre install ---> http://www.mediafire.com/?io9d5tkt6mu0k74
To ROOT use SOC ---> http://www.androidtablets.net/forum...ot-official-huawei-s7-android-2-2-builds.html
Thanks!! good job
what's new?
Any idea if this will work with the Telstra T-Touch Tab (Australia)? I'm told on other threads it's identical to the Ideos S7 except without any memorycard soldered onto the board. - and it seems possibly this only has agps too.
What is the latest available offical firmware? Im using S7 bought from Orange PL and mine ver is S7v100R001C98B022-is this the newest one?
Which do you think is the best out of your own experience?
aurionix said:
Any idea if this will work with the Telstra T-Touch Tab (Australia)? I'm told on other threads it's identical to the Ideos S7 except without any memorycard soldered onto the board. - and it seems possibly this only has agps too.
Click to expand...
Click to collapse
It runs just fine on the T Touch mate
hi, Everyone knows if this rom works with the s7-106?
It has been some time now that Wayteq Came up with two new tablets. xPad-70 and xPad-100 (as seen in the european wayteq site). I curently own the xPad-70 and am eager to find a custom rom to upgrade because it's quite restricted by it's company.... Can anyone help me. When can we have a rom for this device.
Specs of the device:
Display: 7" multi-touch, capacitive
Resolution: 800 x 600 pixel (4:3 aspect ratio)
Processor: AML8726-M Cortex-A9 CPU, ARM Mali-400 3D GPU, NEON SIMD co-processor
System memory: 512 MB
Internal memory: 4 GB
External memory: microSD card support
Operating System: Android 2.2.1 (upgradable to v2.3 later)
Adobe Flash player: supported
Supported file formats: MPEG 1/2/4, H.264/VC-1 @1080P, RealVideo 8/9/10 @720P, MIDI, MP3, WMA, AAC, JPEG, BMP, GIF, PNG
WiFi: 802.11 b/g/n
Bluetooth: V2.1 + EDR class 2 compliant
Network: External 3G dongle support
Webcam: Built-in
Built-in sensors: Light, Acceleration, Orientation
TV output: HDMI
USB connection USB 2.0 OTG
Speakers: Stereo speaker
Microphone: Yes
Earphone: 3.5mm jack
Battery type: Lithium polymer, 3200 mAh
Dimensions: 188 x 143 x 12.5mm
Weight: 430g
Please use the Q&A Forum for questions Thanks
Moving to Q&A
hav you seen this website?
prohardver.hu/tema/re_wayteq_xpad-70_vetek_lenne_kihagyni/hsz_1-50.html&ei=U4aiTphBhOHwA_63ucgF&sa=X&oi=translate&ct=result&resnum=7&ved=0CGIQ7gEwBg&prev=/search%3Fq%3DWayteQ%2BxPAD-70%2Brooted%26hl%3Den%26client%3Dfirefox-a%26hs%3DmnD%26rls%3Dorg.mozilla:en-USfficial%26prmd%3Dimvns[/url]
do you trust it?
it has a rooting file i want to download.. for my wayteq xpad 70 but do not if i should...
and i do not even know the step by step guide of rooting the tablet.. could you help ?
I don't trust sites I can't read. So it's either Greek or English (and I don't completely trust translators).
If I knew how to do it, I wouldn't have posted this question!
I've rooted my xpad-70 using z4 root. I selected permanent root and it worked fine. Think i got z4 root from the market.
The only issue i have is i can't get voice search working and i don't know how to make a first module but i can easily live without both. The tablet is excellent.
It's not root that is the problem. Indeed Z4root fixes this problem. It's that many functions of the Android OS are locked by wayteq, for reasons i keep not understanding...This is common practice for many manufacturers. I suppose it gives them more control of their product. Say in order to make aftermarket products later on, at their leisure!!!
Also the device can very easily have v2.3.5 which is much better. So why shouldn't I be able to have a fully unlocked OS and the latest at that?
Don't know if this is any good. It's for our processor.
http://forum.xda-developers.com/showthread.php?t=1312927
Sent from my HTC Desire using XDA App
I've found a working cifs.ko module. Its in this thread. You don't need the one it mentions later the one in the thread is fine.
http://forum.xda-developers.com/showthread.php?t=1144808
Just unzip then use root explorer to create system/lib/modules/ folder then copy cifs.ko into it. You can use cifs manager to access windows shares.
Sent from my xPAD-70 using Tapatalk
The cifs module works for copying files and streams video fine but when I try to stream an mp3 it crashes out.
Sent from my HTC Desire using XDA App
Today I saw that Wayteq (Europe) Posted the long awaited update. 2.3.4 gingerbread from the support page with instructions. They also state that the CPU will now run at it's 1Ghz Full Capacity. Good news.. All that remains now for me is to root it again!
Excellent news and well spotted. Have you tried it yet. Is it any good.
Sent from my xPAD-70 using Tapatalk
It's good but i Can't root it yet. Z4root and gingerbreak don work as far as I can tell...
I hope now that we have an official ROM from wayteq, someone will start working on a modded version!!!
I'd like to have full admin rights for my device!
Nice one. Is there an option in recovery to back the existing software up. I can do nandroid backups on my desire so it's a bit safer.
Sent from my HTC Desire using XDA App
This site
http://itcafe.hu/tema/re_wayteq_xpad-70_vetek_lenne_kihagyni/friss.html
has a load of info, had to use google translate on my pc to go through it. There are some updates that I have used. They fix wi-fi, GPS!! and also root the gingerbread update. I'll upload them if anyone wants, or you may prefer to have a look at the forum.
Cheers
custom rooted rom
Hi,
There is a custom ROM for it, i will share the link soon. (in 1 hour) The language is hungarian, but u can change to english with these settings:
1. Beállítások (its the hungarian word for Settings. Its in the menu)
2. Nyelv és billentyűzet (means Language and keyboard)
3. Nyelv kiválaszása (Select language)
4. Chose the English languge from that list.
Thats all.
I'll post here the link soon. The rom is rooted, and i'll tell you the instructions to install that rom.
---------- Post added at 09:48 PM ---------- Previous post was at 09:20 PM ----------
Hi again,
Install instruction/download link:
To apply the update, please follow the required steps below:
1. Connect the home charger to the Tablet PC. Charge the battery.
2. Download the compressed file to your PC/Laptop
Here is the link: dl.dropbox.com/u/45414773/WayteQ_xPAD_70_2.3_v2_kelzsoca.zip
multiupload.com/PP5P3MDUUZ
(copy and paste it into the browser)
3. Create an empty folder on your desktop PC / laptop. Extract the downloaded .zip file into this empty folder.
4. Copy the four extracted files ("update.zip", "uImage_recovery", "uImage", "u-boot-512M-UartB.bin") to the root folder of an empty microSD card.
5. Safely remove (disconnect) the microSD card.
6. Turn off the Tablet PC, but keep the home charger connected to it.
7. Insert the microSD card into the Tablet PC. After this step, don't pull out the microSD card.
8. Press and hold down the "volume up" button.
Navigation inside the menu:
Volume up and down buttons can be used to select a menu item.
The "back" button (which is between the "home" and "menu" buttons) will activate a menu item.
9. While holding down the "volume up" button , press and hold down the "power on" button for 4-5 seconds, and release the buttons when you see an "upgrading... please wait" message.
After some seconds....
10. Select "wipe media partition" and activate it. Then select the row starting with "Yes" and activate it.
11. Select "wipe cache partition" and activate it.
12. Select "wipe data/factory reset" and activate it. Then select the row starting with "Yes" and activate it.
13. Select "apply update from sdcard" and activate it, then select "update.zip" file from the list. This procedure can take minutes to complete.
14. Select "reboot system now" and activate it. Don't remove the microSD card. The system will restart itself, after some minutes the graphical user interface of the new Android operating system will appear. After that, remove the microSD card from the Tablet PC and delete the previously copied files from the microSD card.
Copyright:
==================================
WayteQ_xPAD_70_2.3_v2_kelzsoca
2011.11.01.
==================================
Thanks for this. Got my xpad last week im really glad its rooted
Sent from my xPAD-70 using XDA App
Thanks. Excellent ROM.
The only thing that I do not know is why some apps in the market incompatible with the device e.g. evernote and checkpoint mobile.
cincin680123 said:
Thanks. Excellent ROM.
The only thing that I do not know is why some apps in the market incompatible with the device e.g. evernote and checkpoint mobile.
Click to expand...
Click to collapse
There are all the free android apps, like latest google maps, facebook, gmail, youtube...etc.
h t t p://androiddev.orkitra.com/download/apps/
I made a thread for xPAD-70 ICS 4.0.3 rom.
Here is the link: http://forum.xda-developers.com/showthread.php?p=25502924
Hello. I've been looking everywhere and I could not find a STOCK ROM for my Coby Kyros MID1125-4G. It happens that I installed ICS from Coby germany, but that slowed the tablet and has many problems with the WIFI, then updated via OTA to JellyBean and the thing was worse. Now I want to return to Gingerbread, but I don't have the stock image. Any of you have a STOCK ROM for this device? I will be very grateful for your help.
goldgil2 said:
Hello. I've been looking everywhere and I could not find a STOCK ROM for my Coby Kyros MID1125-4G. It happens that I installed ICS from Coby germany, but that slowed the tablet and has many problems with the WIFI, then updated via OTA to JellyBean and the thing was worse. Now I want to return to Gingerbread, but I don't have the stock image. Any of you have a STOCK ROM for this device? I will be very grateful for your help.
Click to expand...
Click to collapse
I think I've done pretty much the same as you....my tablet doesn't seem too bad...a bit glitchy maybe but I have no access to the APN settings meaning I can't use 3g. I'm hunting for answers as well.....if you find out anything before me let me know (and vice versa) :fingers-crossed:
I am glad im not the only one been trying to work out how to get the 4g sim card bit working again for the past few months since I did the update to ICS, was hoping the the update to Jellybean would fix it, tho I have a thought about the update if it helps that is when it downloads the update from the coby site it is downloading for the standard 1125 and not the 1125-4g model.
If i find out a solution or any more will let you know.
Solution
DNO1978 said:
I think I've done pretty much the same as you....my tablet doesn't seem too bad...a bit glitchy maybe but I have no access to the APN settings meaning I can't use 3g. I'm hunting for answers as well.....if you find out anything before me let me know (and vice versa) :fingers-crossed:
Click to expand...
Click to collapse
After hours of seraching on the net I now have my kyros 1125-3g back to 2.3.3 and with 3g support
I have uploaded the files needed to hxxp://kaosmad.com/android/mid1125/1125-3g.zip
There is a pdf file with instructions in the zip file but basically this is what you need to do,
0 make sure coby is turned off
1 - unzip the file
2 - install the drivers from the drivers folder (depending on your operating system)
3 - start the program FWDN_V7_v2.13
4 - click on the '...' button
5 - click on files types and change it to all files
6 - select lk.rom and MTD.img and click on open
7 - click on add files
8 - turn on coby by pushing the on button whilst holding the volume up button for at least 8 seconds, till the coby screen says plug in usb cable
9 - plub in usb cable
10 - wait for windows to finish detecting / installing drivers
11 - the FWDN software should now see the coby and show the memory allocation layout on the right side of the software.
12 - click on NAND Data from the block on the right and create file NAND Data.fai
13 - click on start
14 - wait while coby is updated
15 - when the screen says download complete (turns green) disconnect the usb cable
16 - reset the coby using the reset whole on the side with a paperclip or something else that fits in the whole.
17 - Coby should now be back to factory rom
Hope this is of some help
kaosmad said:
After hours of seraching on the net I now have my kyros 1125-3g back to 2.3.3 and with 3g support
I have uploaded the files needed to hxxp://kaosmad.com/android/mid1125/1125-3g.zip
There is a pdf file with instructions in the zip file but basically this is what you need to do,
0 make sure coby is turned off
1 - unzip the file
2 - install the drivers from the drivers folder (depending on your operating system)
3 - start the program FWDN_V7_v2.13
4 - click on the '...' button
5 - click on files types and change it to all files
6 - select lk.rom and MTD.img and click on open
7 - click on add files
8 - turn on coby by pushing the on button whilst holding the volume up button for at least 8 seconds, till the coby screen says plug in usb cable
9 - plub in usb cable
10 - wait for windows to finish detecting / installing drivers
11 - the FWDN software should now see the coby and show the memory allocation layout on the right side of the software.
12 - click on NAND Data from the block on the right and create file NAND Data.fai
13 - click on start
14 - wait while coby is updated
15 - when the screen says download complete (turns green) disconnect the usb cable
16 - reset the coby using the reset whole on the side with a paperclip or something else that fits in the whole.
17 - Coby should now be back to factory rom
Hope this is of some help
Click to expand...
Click to collapse
Thx for all the great info so far. It allowed me to make my bricked
tablet work again however it seems that I also have problem of the
"Damaged Nand". this message is preventing me from installing CWM after the recovery and
also upgrading to the latest ICS update provided by Coby.
Do you have any idea how to fix this ?? :crying:
Alora said:
Thx for all the great info so far. It allowed me to make my bricked
tablet work again however it seems that I also have problem of the
"Damaged Nand". this message is preventing me from installing CWM after the recovery and
also upgrading to the latest ICS update provided by Coby.
Do you have any idea how to fix this ?? :crying:
Click to expand...
Click to collapse
From what I have read at various places you need to reformat the NAND (internal sd storage) and scan it for errors, this is a know fault as nands like hard drives can have bad sectors, which they write out when originally getting them ready for sale.
Most people recommend hxxp://panasonic.jp/support/global/cs/sd/download/index.html SD Formatter v3 to format it, obviously the coby has to be plugged into your computer to format it.
One note if you have the 3g version of the 1125 with the sim card slot using the coby germany upgrade to ics (or now updated to jellybean) using the updater on their site you wont be able to use the internal 3g sim card slot, this is a known problem to them and they are working on it.
If you need any more help just ask
kaosmad said:
From what I have read at various places you need to reformat the NAND (internal sd storage) and scan it for errors, this is a know fault as nands like hard drives can have bad sectors, which they write out when originally getting them ready for sale.
Most people recommend hxxp://panasonic.jp/support/global/cs/sd/download/index.html SD Formatter v3 to format it, obviously the coby has to be plugged into your computer to format it.
One note if you have the 3g version of the 1125 with the sim card slot using the coby germany upgrade to ics (or now updated to jellybean) using the updater on their site you wont be able to use the internal 3g sim card slot, this is a known problem to them and they are working on it.
If you need any more help just ask
Click to expand...
Click to collapse
Hmm I have dowloaded the SD Formatter 3.1 but it only formates the NAND memory ( flash erase is not suported ) i dont know how to scan for errors, also in FWDN it shows me that the NAND data is:
NAND DATA
( 3235840KB )
Is this ok ?
Also I want to let you know that the original coby germany upgrade to ics I can use the internal 3g sim card slot
I have now the update to ICS but now I dont know how to root and put the market on it, to bad
Did you guys have any luck trying to get APN settings working on your tablet, i mean with the 4.1.1. on?
sorry for my bad english
Is these instructions and the ROM for the 1125 without 3g usable?
If not, is there a tutorial for it and a stock ROM?
To explain:
I must have deleted important files in memory and can't run it any longer. it can not be started.
It is rooted. I would now like to re-flash.
How to get the 1125 in the CWM?
Yes, you can use it. I have also used it to come back to GB.
Alora said:
Thx for all the great info so far. It allowed me to make my bricked
tablet work again however it seems that I also have problem of the
"Damaged Nand". this message is preventing me from installing CWM after the recovery and
also upgrading to the latest ICS update provided by Coby.
Do you have any idea how to fix this ?? :crying:
Click to expand...
Click to collapse
Hi ! I also have the same problem on my MID1125 (without 3G)
...> Damaged NAND.
I forgot to make Step 12 :
12 - click on NAND Data from the block on the right and create file NAND Data.fai
As i read on the internet, the Data.fai File contains the Parition Layout for the NAND Flash. Can someone can make a Data.fai File from his MID1125 Tablet ?
If you do the downgrade steps until step 12, the tablet will not be flashed !
Thank you...
Please, help me. Kyros MID1126.
Hello, my Kyros is a 1126, I realized the process suggested by Kaosmad, but with the rom the Kyros 1125. And it worked, but the format does not match the screen, the touch does not work and some other buttons, I need these files for Kyros 1126, where the "lk.rom" and "mtd.img" if someone can help me , because I can only alert by FWDN_v7 program. From now on, thank you.
Thanks!
kaosmad said:
After hours of seraching on the net I now have my kyros 1125-3g back to 2.3.3 and with 3g support
I have uploaded the files needed to hxxp://kaosmad.com/android/mid1125/1125-3g.zip
There is a pdf file with instructions in the zip file but basically this is what you need to do,
0 make sure coby is turned off
1 - unzip the file
2 - install the drivers from the drivers folder (depending on your operating system)
3 - start the program FWDN_V7_v2.13
4 - click on the '...' button
5 - click on files types and change it to all files
6 - select lk.rom and MTD.img and click on open
7 - click on add files
8 - turn on coby by pushing the on button whilst holding the volume up button for at least 8 seconds, till the coby screen says plug in usb cable
9 - plub in usb cable
10 - wait for windows to finish detecting / installing drivers
11 - the FWDN software should now see the coby and show the memory allocation layout on the right side of the software.
12 - click on NAND Data from the block on the right and create file NAND Data.fai
13 - click on start
14 - wait while coby is updated
15 - when the screen says download complete (turns green) disconnect the usb cable
16 - reset the coby using the reset whole on the side with a paperclip or something else that fits in the whole.
17 - Coby should now be back to factory rom
Hope this is of some help
Click to expand...
Click to collapse
The restore went exactly as you described. I loaded the x86 drivers on my W7 PC. Great instructions and many thanks! Jim
correction to error after install
kaosmad said:
After hours of seraching on the net I now have my kyros 1125-3g back to 2.3.3 and with 3g support
I have uploaded the files needed to hxxp://kaosmad.com/android/mid1125/1125-3g.zip
There is a pdf file with instructions in the zip file but basically this is what you need to do,
0 make sure coby is turned off
1 - unzip the file
2 - install the drivers from the drivers folder (depending on your operating system)
3 - start the program FWDN_V7_v2.13
4 - click on the '...' button
5 - click on files types and change it to all files
6 - select lk.rom and MTD.img and click on open
7 - click on add files
8 - turn on coby by pushing the on button whilst holding the volume up button for at least 8 seconds, till the coby screen says plug in usb cable
9 - plub in usb cable
10 - wait for windows to finish detecting / installing drivers
11 - the FWDN software should now see the coby and show the memory allocation layout on the right side of the software.
12 - click on NAND Data from the block on the right and create file NAND Data.fai
13 - click on start
14 - wait while coby is updated
15 - when the screen says download complete (turns green) disconnect the usb cable
16 - reset the coby using the reset whole on the side with a paperclip or something else that fits in the whole.
17 - Coby should now be back to factory rom
Hope this is of some help
Click to expand...
Click to collapse
After following the instructions I had an error and it would not boot.. so I did the same again but changed from "default download" to "Low format whole memory before download" (this does remove all your data as the warning states) then followed steps 3 to 13 again you need to do the NAND data.fai again so that it works and I have the stock ROM just added
Pplaystore via sd card.
Additional Support, ROM upgrades via Donation
Ryder663 said:
After following the instructions I had an error and it would not boot.. so I did the same again but changed from "default download" to "Low format whole memory before download" (this does remove all your data as the warning states) then followed steps 3 to 13 again you need to do the NAND data.fai again so that it works and I have the stock ROM just added
Pplaystore via sd card.
Click to expand...
Click to collapse
Excellent support site for all thing Kyros.
tipsters ROM upgrades are fantastic and well worth the recommended donation.
Hello,
I used instrucjion to downgrade android to v.2.3.3. It worked, but after downgrade I can't turn on 3G.
I have 3G option, but when I click on 3G i see all the time "Turning on..." I don't see 3G enable or something else. 3G nor working.
During flashing to android v2.3.3 I have inserted SIM card to tablet :/ Reset to default do not work :/
kaosmad said:
After hours of seraching on the net I now have my kyros 1125-3g back to 2.3.3 and with 3g support
I have uploaded the files needed to hxxp://kaosmad.com/android/mid1125/1125-3g.zip
There is a pdf file with instructions in the zip file but basically this is what you need to do,
0 make sure coby is turned off
1 - unzip the file
2 - install the drivers from the drivers folder (depending on your operating system)
3 - start the program FWDN_V7_v2.13
4 - click on the '...' button
5 - click on files types and change it to all files
6 - select lk.rom and MTD.img and click on open
7 - click on add files
8 - turn on coby by pushing the on button whilst holding the volume up button for at least 8 seconds, till the coby screen says plug in usb cable
9 - plub in usb cable
10 - wait for windows to finish detecting / installing drivers
11 - the FWDN software should now see the coby and show the memory allocation layout on the right side of the software.
12 - click on NAND Data from the block on the right and create file NAND Data.fai
13 - click on start
14 - wait while coby is updated
15 - when the screen says download complete (turns green) disconnect the usb cable
16 - reset the coby using the reset whole on the side with a paperclip or something else that fits in the whole.
17 - Coby should now be back to factory rom
Hope this is of some help
Click to expand...
Click to collapse
little help please!!
hi xda-developers, im just need a little help with my kyros 1125 4gb no 3g, already google my problem but i didnt found anything about hard reset, i dont have the lock code for my tblet and i want to reset it, i tryed the normal way for android but nothing hapen, if any body know a tutorial how to reset my device, please share the information, thank you soo much for ur help
fidodj23 said:
hi xda-developers, im just need a little help with my kyros 1125 4gb no 3g, already google my problem but i didnt found anything about hard reset, i dont have the lock code for my tblet and i want to reset it, i tryed the normal way for android but nothing hapen, if any body know a tutorial how to reset my device, please share the information, thank you soo much for ur help
Click to expand...
Click to collapse
1125-4G rom
Download file from here
https://www.dropbox.com/s/fixhl34x7qr13v6/1125.zip?dl=0
Copy entire 1125.zip folder to desktop
Extract 1125.zip to desktop
Install PdaNetA4170.exe driver ( This should allow you to transfer files with Fastboot )
This is Version 4.17 installer for Windows 8/7/Vista/XP (both 32/64bit)
Extract CWM recovery img_1125 folder to desktop by itself ( Do not remove any files from this folder )
Move zip files from zips folder to micro sd card and insert sd into tablet ( leave these in zip format !! )
coby_gapps.zip
coby_mid1125-seed-0012.zip
Superuser-3.1.3-arm-signed.zip
Also move apks from apks folder to MicroSD card
Uni-init+v1.0.apk
Google_Play_serv.ices-signe.d .apk
Busybox.apk
Link2sd.apk
and
market-helper-2.0-beta.apk ( this will allow spoofing of market for not compatible apps )
Open cmd window
( menu , run , when window opens , enter “cmd” without quotes )
Cd to directory
ie ,
type in window
cd desktop , ( enter )
cd CWM recovery img_1125 ( enter )
Now place 1125 into fastboot mode , power ( or reset button ) and volume down , tablet will show fastboot mode in lower left corner
Plug in usb cable to pc and tablet
Then in cmd prompt type
fastboot boot recovery.img ( enter )
It will show some stuff , flash ok and done ok
Tablet should boot to CWM give it a moment to do so ( You will see CWM Recovery Top hat and such )
Volume up is up , Volume down is down , Home ( Silver Button ) is select
Go to and select flash zip from sd card
This will pull up menu of following zip files
Flash each zip file
coby_mid1125-seed-0012.zip
coby_gapps.zip
Superuser-3.1.3-arm-signed.zip
Select reboot
Tablet will boot ,again give it a moment ( You will see Coby and then Android splash screen )
Select language from first screen ( as it will be in Dutch ), finish setup of tablet
Open ES File Explorer , go to tools setting in ES File Explorer and select
“Root Explorer” to on , allow when Super User prompt shows , this will prove SU is installed and working
Open ES File Explorer , Select sdcard top right , Select storage
Install Google_Play_serv.ices-signe.d .apk ( To sync Play Store )
Install Busybox.apk
Install Link2sd.apk
Install Uni-init+v1.0.apk
Open Uni-init+v1.0.apk , install intd support
( you will need busybox installed first for this to work )
You now have working Play Store , Superuser and Android 4.1 with Intd support
For Extended memory ,( You need this )
Increase Internal Memory by Link2SD : Min 2 GB microSD
In order to add memory to Coby 1125, your micro SD card used for install will need to be formatted
Copy all files you wish to keep from micro SD to desktop as it will be wiped
• Backup all your files on memory card.
• Go into the Recovery Mode ( as above , fastboot boot recovery.img ) ( Your operating system will be fine )
• Make a nandroid backup at this time
• Select “Advanced”, and then choose “Partition SD Card”.
• Then Choose your size ( if you have a 2GB Memory Card, choose 512 MB, and if you have a 4 GB Memory card, you can choose 1024 MB, ext ).
• Select 0 Swap.
• Wait for the process to finish, and then select Reboot
You’ve just made a partition on your memory card, and its ready to use.
Now follow the steps below for Link2SD
• Open Link2SD. You will be prompted to choose between ext2,ext3,ext4 and FAT32.
• Choose ext2
• Select OK ,
• It will then say, “Mount Script Created”.
• Now you Reboot your Tablet
• Open Link2SD again, if any message does not appear ,it means you succeeded.
• Go to Link2SD > Setting( far right top icon ) scroll down > Check the autolink. (to automatically move apps upon installation).
If you already have some apps listed , select “create link” ( be sure to check the files: app, dalvic-cache, and library files).
Move to SD option only moves app to SD it does not link them
Now to check the memory, select “Storage Info” . this will be showing you up the current status of your internal memory.
You should see as below SD Card 2nd Part
To move a system App you can long press App , it will pull up menu , select convert to user App let it do its thing
Select App again and it will open option to create link as installed user apps do
So far I have moved Calculator , VPN , Music FX , ES File Explorer and Sound Recorder with no issue
Use Link2Sd and (long press) on SystemUpdate.apk ( /system/app/SystemUpdate.apk ) and freeze app.
This will stop System Update from happening at random moments or on reboot
There is no Update to install though the System thinks so (without freezing it will continue to show updates available)
STOCK ROM
--------------------
I am posting a list of stock firmware(s) that I can find for the A706 here, along with instructions on how to install it.
FIRMWARE LIST
-------------------------
Build Number: A706_ROW_S018:
Details:
Firmware Type: Official Release
Languages: English, Russian, Chinese, Indonesian & Vietnamese
Build Date: 15/07/2013
OS: Android 4.1.2 with Lenovo Magic UI
Download Link: http://lenovo-forums.ru/files/file/242-rom-a706-1-s-2-001-0018-130705-row/
(You need to click on the green button on the page. Once you click there then you need to register and logged in, to download it.)
INSTRUCTIONS
-----------------------
A memory card is required.
Boot into Android normally.
Connect your phone to your PC/Laptop with a USB cable and when asked (or in USB connection settings), please select USB Mass storage mode to mount SD card.
On the root of the memory card, create a folder called "sdfuse".
Unzip the downloaded firmware, you will get a QSB file.
Copy the QSB file to the sdfuse folder that we created earlier on the root of SD card.
Note: Please make sure that your phone has atleast 65% power before attempting or beginning upgrade. Or keep charger connected during the process.
SD card upgrade process:
Long press VOL UP + POWER_KEY to enter the droidboot,
A menu will appear. Select the fourth option, SDUPDATE.
At the bottom of the screen, you can see the progress and status of the update
When you see the message "SDCARD UPDATE SUCCESS!!!", this means you successfully completed the upgrade process
Now, reboot your device and hopefully it should be updated.
CREDIT: Instructions were taken from this post and formatted and edited for better understanding.
If I helped you in anyway, Please show some courtesy & hit the THANKS button!
I have an android car head unit with Allwinner T3.
I asked from the seller the OS files to update my unit because I was experiencing some issues. I received these two files
os_update_YMHC0101-N39-2.3.4.3.12_20180601_152348.zip
YMHC0101-N39-2.3.4.3.12_20180601_152348.img
I used the second file with PhonixCard to create a sd card and update my unit.
The update was successful and my unit information in About Device menu are:
Android version: 7.1.1
Hardware Information: Quad Core AllWinner
Kernel Version: Linux 3.10.65
OS Version: BSP 2.3.4.2.12 - IVT - 180601
MCU Version: 20180426-1-KC1-18
I want to install an app called VocalizerEx. The default TTS engine in my head unit is PicoTTS. I installed VocalizerEx and selected in settings but it's not activated. If I exit the menu and reenter I see that PicoTTS is the activated engine. I think that PicoTTS gets selected as the default TTS engine because it has been installed as a system app. I could convert VocalizerEx to system app if the head unit was rooted but I couldn't find any information to root my unit.
Since I have the above .zip and .img files I was wondering if there is a way to edit them and create a custom update file with VocalizerEx installed as a system app. If it's possible to edit these files I would like to change the boot animation as well.
I explore my head unit file structure and I see that it has the same file structure with the .zip file I have. Could I use this .zip to create the .img update file or just unpack and repack the .img?
I tried DragonFace but I got an error.
How could I edit this .img file? What tools do I need? (I could work on Windows/Linux/Mac OS X.)
Is it safe to unpack and repack the .img? Could a corrupted .img file brick my device?
Hey,
I have an Android Allwinner T3 device and I have problems with it.
I received operating system files from the vendor to update my unit. I received these three files:
- YMHC0101-N39-2.3.4.3.12_20180601_152348.img
- phonixcard.exe
- mcu-201804260001KC1-1522.img
Unfortunately, I have no instructions on how to do it. Could you write me one by one how to make an update?
_carlos_ said:
Hey,
I have an Android Allwinner T3 device and I have problems with it.
I received operating system files from the vendor to update my unit. I received these three files:
- YMHC0101-N39-2.3.4.3.12_20180601_152348.img
- phonixcard.exe
- mcu-201804260001KC1-1522.img
Unfortunately, I have no instructions on how to do it. Could you write me one by one how to make an update?
Click to expand...
Click to collapse
What problems do you have?
To update the OS:
1. Insert a formatted microSD card in an external microsd reader (computer's internal reader never worked for me)
2. Run phonicard as administrator. Select the .img file (YMHC0101-N39-2.3.4.3.12_20180601_152348.img), select the letter of your microSD, select "product" and hit "Run". After a few minutes you should see a green status bar or a message "Magic Complete/Burn End..." depending on Phonixcard version.
3. Turn off your headunit, remove all usb and sd cards from it, insert your new card in the GPS slot and turn it on. You should see a green bar loading. It takes about 1-2'. When it shows "CARD OK" on screen turn it off and remove the microSD.
4. Turn it on again and it should start booting. The first boot will take longer, 3-5'.
To update the MCU:
You should use another empty and formated microSD card. If you want to use the same, you should format it but also you should delete the hidden partition Phonixcard has created. Open Phonixcard with microSD connected and select "Format to Normal".
1. Copy mcu-201804260001KC1-1522.img in microSD card (copy the file in card, don't use Phonixcard to burn it).
2. Turn on you headunit and allow it to start. Remove all usb and sd cards and insert your microSD (with only mcu update in it).
3. Wait a few seconds and it should open a screen showing you that it found a MCU update. Select it and it should guide you through the process. Don't turn it off. Allow it to finish and reboot.
koroji said:
What problems do you have?
Click to expand...
Click to collapse
For me, there is a problem, that after selecting a home page, applications cyclically appear every 1 second and disappear. You can not start any application.
koroji said:
2. Run phonicard as administrator. Select the .img file (YMHC0101-N39-2.3.4.3.12_20180601_152348.img), select the letter of your microSD, select "product" and hit "Run".
Click to expand...
Click to collapse
Should I do it on my computer or Android Allwinner T3?
Yes, phonixcard is a computer program
Hello,
I have a problem with running the PhoenixCard application. I copied the applications onto the computer and opened it. I ran the PhoenixCard.exe file as an administrator. The user account control window appears: "Do you want to allow the following program from an unknown publisher to make changes to this computer?" I pressed the YES button, but the window disappears and nothing happens.
Please, tell me what to do.
Regards Robert
Write still what you used the phoenixcard version?
Where can I download firmware updates? I can't find vendor website.
You must write to the seller.
I've bought on Amazon... i'm sure that seller will not reply
Try it, I bought it on Aliexpress and the seller is replying to my messages.
---------- Post added at 11:42 PM ---------- Previous post was at 11:07 PM ----------
What is your exact model?
_carlos_ said:
Try it, I bought it on Aliexpress and the seller is replying to my messages.
---------- Post added at 11:42 PM ---------- Previous post was at 11:07 PM ----------
What is your exact model?
Click to expand...
Click to collapse
Czesc,
Pisalem na Elektrodzie do Ciebie w sprawie plikow do radyjka i dzialajacego PhoenixaCarda
Jak masz chwile daj znac lub linka na priv
Pzdr