I have a Verizon Note 2 running 4.4.2.
I successfully rooted it without unlocking the bootloader or flashing a custom recovery, everything was stock. Everything worked fine after and I was able to use root-requiring apps.
Then, after attempting to flash custom recovery, since the bootloader was locked, I am now stuck at the screen that says: "System software not authorized by Verizon Wireless has been found on your phone..."
I am able to enter recovery (the stock recovery) as well as go into download mode. Normally this wouldn't be a problem as I could just flash stock through Odin in download mode.
However, ever since the soft-brick Odin won't recognize my phone (the yellow COM square does not come up), which is strange because Odin recognized my Note 2 in download mode before this happened.
And even stranger is the fact that it is not a driver issue, as when I plug in my Note 2 in download mode I get a message from Windows 7 saying that the serial gadget device driver was found and installed successfully (and the phone also shows up in Device Manager in control panel as fully installed while in download mode.
Yet Odin won't recognize it.
I have spent days searching for an answer and have yet to come across an issue identical to mine (everyone seems to be able to just flash stock through Odin to fix this particular soft-brick, but Odin is not recognizing my device), so I finally decided to post here.
Any suggestions at all are welcome as I am somewhat desperate at this point. I'd just like to get it back to stock (or flash a custom rom, it does not matter as long as I can get the phone to work).
I would like to point out that I have already tried the following:
- Different USB ports
- Using different USB cables
- Uninstalling and reinstalling the drivers
- Wipe/Factory Reset in stock recovery
From what I can see, my only options are to either somehow get Odin to recognize the phone (suggestions welcome here), or somehow flash stock through the default recovery (if possible, again, any input is appreciated).
William31 said:
I have a Verizon Note 2 running 4.4.2.
I successfully rooted it without unlocking the bootloader or flashing a custom recovery, everything was stock. Everything worked fine after and I was able to use root-requiring apps.
Then, after attempting to flash custom recovery, since the bootloader was locked, I am now stuck at the screen that says: "System software not authorized by Verizon Wireless has been found on your phone..."
I am able to enter recovery (the stock recovery) as well as go into download mode. Normally this wouldn't be a problem as I could just flash stock through Odin in download mode.
However, ever since the soft-brick Odin won't recognize my phone (the yellow COM square does not come up), which is strange because Odin recognized my Note 2 in download mode before this happened.
And even stranger is the fact that it is not a driver issue, as when I plug in my Note 2 in download mode I get a message from Windows 7 saying that the serial gadget device driver was found and installed successfully (and the phone also shows up in Device Manager in control panel as fully installed while in download mode.
Yet Odin won't recognize it.
I have spent days searching for an answer and have yet to come across an issue identical to mine (everyone seems to be able to just flash stock through Odin to fix this particular soft-brick, but Odin is not recognizing my device), so I finally decided to post here.
Any suggestions at all are welcome as I am somewhat desperate at this point. I'd just like to get it back to stock (or flash a custom rom, it does not matter as long as I can get the phone to work).
I would like to point out that I have already tried the following:
- Different USB ports
- Using different USB cables
- Uninstalling and reinstalling the drivers
- Wipe/Factory Reset in stock recovery
From what I can see, my only options are to either somehow get Odin to recognize the phone (suggestions welcome here), or somehow flash stock through the default recovery (if possible, again, any input is appreciated).
Click to expand...
Click to collapse
Wow... I'm stumped too as to why Odin won't recognize the phone. What method did you use to try to flash the custom recovery and what recovery did you flash? (You probably know now, but just in case.... if you can get the phone restored to stock 4.4.2 again... then you can't flash a standard custom recovery onto the phone because of the bootloader being locked down. You can use the modified TWRP called Safestrap recovery if you root again... and can only flash 4.4.2 touchwiz roms with stock 4.4.2 kernel after you get rooted again).
When you rooted, all I can think of is that something may have corrupted the drivers somehow and that's now conflicting with ODIN. With the phone in download mode... have have you went into the PC's Device Manager and tried to delete/reinstall any Samsung related drivers, (make sure to look for hidden drivers.... click scan for hardware changes after deleting them and the computer should reinstall the correct drivers). Also... have you made sure no other conflicting programs (like Kies) are running in the background?
You might try to do a system restore to an earlier point on your PC where ODIN recognized the phone to see if that would work.
If ODIN version 3.07 isn't recognizing the phone, you could try a newer version of ODIN. Here's some links to other ODIN versions that you might try: Download link for ODIN 3.09 ; Download link for ODIN 3.10.0. ~~With the newer ODIN versions, they have replaced the "PDA" slot with "AP"--so the .tar firmware file goes into AP in the newer ODIN. ****(For reference--Here's the XDA Thread where XDA recognized contributor -CALIBAN666- posted these links to newer ODIN versions. Hit the thanks button for him ****
---------------
If you can't get the restore to work with ODIN, you could try Samsung Kies to see if it can fix the device...
Where to download Kies -- http://www.samsung.com/us/kies/
Emergency Firmware Recovery using Kies 3 -- http://www.samsung.com/us/support/faq/FAQ00059169/81100
I hope that some of this info helps and that you can get it fixed.
Good luck!
mattnmag said:
Wow... I'm stumped too as to why Odin won't recognize the phone. What method did you use to try to flash the custom recovery and what recovery did you flash? (You probably know now, but just in case.... if you can get the phone restored to stock 4.4.2 again... then you can't flash a standard custom recovery onto the phone because of the bootloader being locked down. You can use the modified TWRP called Safestrap recovery if you root again... and can only flash 4.4.2 touchwiz roms with stock 4.4.2 kernel after you get rooted again).
When you rooted, all I can think of is that something may have corrupted the drivers somehow and that's now conflicting with ODIN. With the phone in download mode... have have you went into the PC's Device Manager and tried to delete/reinstall any Samsung related drivers, (make sure to look for hidden drivers.... click scan for hardware changes after deleting them and the computer should reinstall the correct drivers). Also... have you made sure no other conflicting programs (like Kies) are running in the background?
You might try to do a system restore to an earlier point on your PC where ODIN recognized the phone to see if that would work.
If ODIN version 3.07 isn't recognizing the phone, you could try a newer version of ODIN. Here's some links to other ODIN versions that you might try: Download link for ODIN 3.09 ; Download link for ODIN 3.10.0. ~~With the newer ODIN versions, they have replaced the "PDA" slot with "AP"--so the .tar firmware file goes into AP in the newer ODIN. ****(For reference--Here's the XDA Thread where XDA recognized contributor -CALIBAN666- posted these links to newer ODIN versions. Hit the thanks button for him ****
---------------
If you can't get the restore to work with ODIN, you could try Samsung Kies to see if it can fix the device...
Where to download Kies -- http://www.samsung.com/us/kies/
Emergency Firmware Recovery using Kies 3 -- http://www.samsung.com/us/support/faq/FAQ00059169/81100
I hope that some of this info helps and that you can get it fixed.
Good luck!
Click to expand...
Click to collapse
So I tried recovering with Kies and it just kept throwing errors at me, then finally I just closed it and, am not quite sure why, but went into Odin and it worked! Apparently trying to recover with Kies somehow fixed the Odin issue and I was able to flash stock through Odin. Thanks so much!
You mentioned there was a way to flash a safestrap recovery and then flash touchwiz roms? Do you by chance have instructions on how I could do this, or links to this information...?
William31 said:
So I tried recovering with Kies and it just kept throwing errors at me, then finally I just closed it and, am not quite sure why, but went into Odin and it worked! Apparently trying to recover with Kies somehow fixed the Odin issue and I was able to flash stock through Odin. Thanks so much!
You mentioned there was a way to flash a safestrap recovery and then flash touchwiz roms? Do you by chance have instructions on how I could do this, or links to this information...?
Click to expand...
Click to collapse
Cool. Glad you got it fixed.
As you know, you can root with GhettoRoot from this thread: http://forum.xda-developers.com/showthread.php?p=57238246
Then can install Safestrap from this thread: http://forum.xda-developers.com/showthread.php?p=51616723
I've never used Safestrap because I can use regular custom recoveries like CWM and TWRP. I'm still on a 4.1.2 unlocked bootloader and currently running TrentsKKRom, Build #2...which is 4.4.2 based with stock kernel, so I think it would work with Safestrap.
I'd recommend reading through the Safestrap thread thoroughly and asking questions there to make sure you get everything installed correctly. I've read that with Safestrap, you need to make a backup of your Stock ROM first and save it somewhere safe, like to your computer and on your external sd card...so you can easily restore it if needed. (I'd also make a backup of the ESF in Safestrap if it lets you, then save it somewhere safe).
After you are rooted with Safestrap, you'll have to flash custom ROM's over the stock slot in Safestrap, as the other slots apparently don't work. Again, you're limited to only using Touchwiz ROM's with the stock kernel because of the bootloader still being locked.
Check out TrentsKKRom and Alliance build 30 . (I personally like Trent's build 2 best with the S5 clean theme). I've also found Trent's ROM to be really smooth without UI lagging, the Bluetooth works good with no stuttering, and it pairs well with my Sony Smartwatch 3. (Edit: If you do try Trent's ROM, you may need to install a couple apps.... Chainfire's Supersu app to control your root permissions (at least I needed to), and the FolderMount app to fix a KitKat internal storage mounting issue).
Have fun!!
Related
Hi I hope someone can help me. I have searched this forum but could not find a similar situation to what I ended up in...
I tried to install a custom ROM on my Galaxy Tab 10.1 using the CWM/Odin.
This seemed succesful but was not, it did not start but was stuck in the Samsung logo.
So I tried entering the CWM and download and install an original Samsung ROM. I can get it into CWM, but CWM cannot enter the download mode only the other mode.
In this mode all options are available:
- reboot
- apply update from SD card
- wipe data/factory reset
- wipe cache partition
All options have been tried without any luck. In the update from SD card it only shows ...
or Error opening /data/media: no such file or directory
Any ideas how I could get this directory back or put a ROM on the Samsung in this situation.
Odin does see the Galaxy but as I cannot get it into Download mode I am unable to download anything to it.
All or any suggestions are very welcome!
1. CWM (Clockworkmod) =! Odin.
In the beginning, you don't have CWM installed. You install CWM, by flashing CWM on your Phone with odin.
Odin is the Windows Programm, that is used to flash Recoveries/ROM's/Kernels onto your device.
2. it seems, that you still have the default Samsung recovery installed, that meand CWM is not yet flashed on your device.
If the flashing process was succesful (I suppose it was done with odin), but you can't get past the Samsung logo, that means, you probably flashed a rom, that isn't made for your device(ex. a GTab 10.1v Rom).
If you DID flash a wrong rom, then you probably ****ed up the partition table and removed the Download Mode(Odin Mode). Strange thing is, that you still have the Stock recovery.
Could you please redirect us to the rom you downloaded?
Also, did you flash with a repartition on and/or a .pit file?
hi Kaukassus,
thanks for the reply.
OK I checked the files and what I did.
I think I totaly screwed this up. It was a theme I tried to install the AOSP_HC_v1.3_3G+KI1.
I rooted the Tab. So first when the Tab was still functioning installed it on the TAB via USB.
Than tried to install this via update from SD card.
This appeared to work initially. But hung at the start.
After that I tried (via Power Volume Up) wipe data/factory reset.
No luck.
After that I tried wipe cache partition followed by wipe data/factory reset.
And this is what I got now..
Bad news is the Tab was/is a X-mas present and I managed to screw it up even before I officially got it !-(
The valuable lesson you're learning is that you need to be aware exactly what things you're flashing and their compatibility with your device and the software it's running.
You haven't mentioned what specific device you're using or the specific things you've tried to flash (as kaukassus pointed out, direct links to threads where you got the files you tried to flash are best). Not sure if you're aware but not all GT 10.1's are equal; there are several models out there and each and every ROM is specific to a particular device. Verizon LTE GT 10.1's like mine can't take ROMs from any other device for example, it's likely that the new T-Mobile 4G one's wont be able to trade ROMs with Verizon ones . . you get the point.
When you say you installed via USB what exactly did you mean? If you simply copied a zip file via USB to the tab to flash in recovery mode that's not installing; the flashing from recovery may be but the file copy operation is not. If on the other hand you pushed things via ADB or you flash using Odin software then that's a different story.
Best thing to do at this point is to properly identify your device, look for a stock recovery image for Odin and flash that via Odin to your device. At that point you can start from scratch again to build what you want.
Thanks Muzzy996.
You are right. I was in a rush and should have taken more time.
However I am getting somewhere. Managed to get in download mode twice today, don't ask me how. This Tab just will not go into download mode!
However I did not have the stock ROM ready to be installed.
Will keep you updated.
i have the same problem. i just rooted my device was going to overclock. decided to save my rom with rom manager. saved it device went to reboot now the samsung galaxy 10.1 shows up screen goes dim then shuts off, and will cont. do this. i can get into download mode but recovery will not work. is there anyway to download my stock rom. im using verizion 4g 10.1 any help would be great, btw sorry to thread jack
Problem solved.
Managed to get it in download mode again and install stock rom via Odin.
Appeared to work fine. But kep switching off, even after full night of charging.
This morning Tab was dead after recharging whole night..
Got it back on by holding volume down and power button down.
i found a stock rom and im trying to upload it via odin, however odin does not find my tab? any ideas. btw congrats on getting ur tab back
I crashed both my I9000 (galaxy s) flashing custom roms and my tab 10.1 (editing some system files) both ended up just looping but managed to get both back. I purchased a small connector of ebay £1.59 that has just a resistor accross pins 4&5 331k I think anyway plugging this into most samsung devices boots them into download mode. Even before getting my resistor I managed to get things working I think that you'd have to be properly unlucky to really brick a samsung I've flashed both my devices with all sorts of crap with my little resistor I just reset them with ease.
Brian
h2bmess said:
i found a stock rom and im trying to upload it via odin, however odin does not find my tab? any ideas. btw congrats on getting ur tab back
Click to expand...
Click to collapse
did you ever resolve this issue? i am currently faced with the same issue.
Hi there. Let me just start off by saying, despite my efforts, I still have next to no idea as to what I am doing.
My Phone: Galaxy SII i9100T (Australian Telstra variant), ICS 4.03
So today I decided to root my phone and install cyanogenmod 9 following a guide in a magazine (that was written for cyanogenmod 7 if that makes a difference). Initially it told me to root with SuperOneClick, but that wasn't working for my device as the program would eventually not respond.
After snooping around on the internet I eventually ended up rooting my phone (I think) with Odin 1.85 installing an image called CF-Root-SGS2_XW_NEE_LPG-v5.5-CWM5 under the PDA option (as per instructions of one particular website). That worked.
So then I consulted the magazine again, and it said to download the heimdall suite from the cyanogenmod wiki galaxy sII page, and run a program called zadig, list all devices, and change the 'Samsung Android' driver to whatever zadig installs. However, my phone did not come up as that, it came up as two other files, one with a driver called Modem, and the other with a driver that I cannot remember the name of. I can confirm that they were my phone and no other USB devices as they disappeared when I unplugged my phone. I chose the driver that wasn't called Modem. That seemed to work fine.
Next it said to install a clockworkmod image using the heimdall suite. The image was recovery-clockwork-5.5.0.4-galaxys2 ....I eventually got that to work.
However, no matter what I do now, I cannot get into the clockworkmod recovery screen to install cyanogenmod 9. Did I do something wrong? I think I may have made a mistake with zadig, as now it lists my phone as 4 devices: Samsung_Android, Samsung_Android, Samsung, and MTP.
I know this is an absolute mess of a situation, but I desperately need help. If I cant go through with the installation of cyanogenmod, can I at least reset everything back to normal like it was out of the box?
Any help would be very much appreciated.
You could e-mail the editor of the mag and complain
Sent from my GT-I9100 using xda premium
ultimatebestusername said:
Hi there. Let me just start off by saying, despite my efforts, I still have next to no idea as to what I am doing.
My Phone: Galaxy SII i9100T (Australian Telstra variant), ICS 4.03
So today I decided to root my phone and install cyanogenmod 9 following a guide in a magazine (that was written for cyanogenmod 7 if that makes a difference). Initially it told me to root with SuperOneClick, but that wasn't working for my device as the program would eventually not respond.
After snooping around on the internet I eventually ended up rooting my phone (I think) with Odin 1.85 installing an image called CF-Root-SGS2_XW_NEE_LPG-v5.5-CWM5 under the PDA option (as per instructions of one particular website). That worked.
So then I consulted the magazine again, and it said to download the heimdall suite from the cyanogenmod wiki galaxy sII page, and run a program called zadig, list all devices, and change the 'Samsung Android' driver to whatever zadig installs. However, my phone did not come up as that, it came up as two other files, one with a driver called Modem, and the other with a driver that I cannot remember the name of. I can confirm that they were my phone and no other USB devices as they disappeared when I unplugged my phone. I chose the driver that wasn't called Modem. That seemed to work fine.
Next it said to install a clockworkmod image using the heimdall suite. The image was recovery-clockwork-5.5.0.4-galaxys2 ....I eventually got that to work.
However, no matter what I do now, I cannot get into the clockworkmod recovery screen to install cyanogenmod 9. Did I do something wrong? I think I may have made a mistake with zadig, as now it lists my phone as 4 devices: Samsung_Android, Samsung_Android, Samsung, and MTP.
I know this is an absolute mess of a situation, but I desperately need help. If I cant go through with the installation of cyanogenmod, can I at least reset everything back to normal like it was out of the box?
Any help would be very much appreciated.
Click to expand...
Click to collapse
I suggest you restart from scratch following these steps:
1. read everything about flashing and rooting you can find on this site (read stickies first)
2. same as 1.
3. same as 1.
4. flash the latest stock firmware for your phone
5. root your phone
6. finally flash some other ROM
As a general rule, do not forget to take extra precautions when you flash anything: ALWAYS DO A NANDROID BACKUP IN CWM...
Performs a wipe date , factory reset , then follow the guide;
[GUIDE] ROOT/UNROOT Stock ICS Firmware without flashing unsecure kernel
Simple way to root and unroot stock kernel without flashing insecure kernel.
Don't worry about custom counter and yellow triangle, with this method they never appear, because we only rooting, it's a rooting script not a custom kernel.
This rooting script included Busybox installer.
Rooting
Download this File first and put in your SDCARD
- CWM via stock recovery ;( http://dl.dropbox.com/u/34053267/CWM.zip) , or download zip from http://clockworkmod.com/rommanager
- SU-Busybox-Installer.zip ( https://dl.dropbox.com/u/34053267/SU-Busybox-Installer.zip )
Reboot to recovery.
Choose apply update from external storage.
Choose CWM.zip and wait until CWM recovery appear.
Choose install zip from sdcard or external SD
Choose and Install SU-Busybox-Installer.zip
Reboot
You are done and now your device is Rooted
Method 2
CF_Root + stock kernel + [optional] Mobile Odin Free version
Here, you use an older CF_Root kernel, and flash your newer stock kernel
Quote:
First, get a CF_Root kernel from CF_Root thread here http://forum.xda-developers.com/showthread.php?t=1103399. Just get the nearest one to your ROM. You can download any ICS kernel, it will do the job for the root only purpose
Flash the CF_Root kernel with odin
Now, flash again your stock kernel with odin. You can get a stock kernel from lyriquidperfection thread http://forum.xda-developers.com/showthread.php?t=1619525
Do not forget to thank / donate to him
No stock kernels for you? use Mobile Odin free version (see below)
After flashing the stock kernel, root will usually stay and you will be reverted back to your stock recovery instead of CWM recovery
Hi, so I've been flashing for a while now on my phone and my friend wanted to root his phone so i agreed to help him out. After flashing multiple files in order to get cwm recovery and just get everything working, the phone started to act up.
Here are the problems:
Phone can boot into stock recovery but i cant flash anything from it
i wiped data/factory reset many times.
i tried to install the cwm kernal by applying update from sd card (I followed the install custom recovery instructions from here: http://wiki.cyanogenmod.org/w/Install_CM_for_i777) but when into recovery to flash, 2 red signs come up saying "E: Failed to verify whole-file signature" and "E: signature verificatoin failed" after this is just aborts the process
i tried download mode, but none of my computers recocgnize the phone (2 computers) i have tried all usb ports, reinstalling usb drivers, different usb ports many times but all have failed
if i try to boot, the phone just stays stuck on the Samsung galaxy s2 logo (no triangle? even though its rooted)
my only option is to hang out in recovery, i have a bunch of files saved to an external sd card but i cannot access that from stock recovery
any help would be appreciated, Thanks
You can not install any unsigned files with stock 3e recovery, as you have discovered. That is normal behavior.
I don't know why performing a wipe data/factory reset from 3e recovery does not clear the phone to boot normally. It should. But since it won't...
You will need to get the phone recognized by a computer, and then flash with Odin, or you could try flashing with Heimdall command line. I would suggest that you flash the full stock plus root I777UCKH7 (2.3.4), and then when it boots normally into the system, install Mobile Odin Lite or Mobile Odin Pro, and use that to flash a custom kernel. You can find the stock firmware in the Download Repository, and the basic directions in my guide, both of which are linked in my signature.
creepyncrawly said:
You can not install any unsigned files with stock 3e recovery, as you have discovered. That is normal behavior.
I don't know why performing a wipe data/factory reset from 3e recovery does not clear the phone to boot normally. It should. But since it won't...
You will need to get the phone recognized by a computer, and then flash with Odin, or you could try flashing with Heimdall command line. I would suggest that you flash the full stock plus root I777UCKH7 (2.3.4), and then when it boots normally into the system, install Mobile Odin Lite or Mobile Odin Pro, and use that to flash a custom kernel. You can find the stock firmware in the Download Repository, and the basic directions in my guide, both of which are linked in my signature.
Click to expand...
Click to collapse
The hardest part about this is getting my computers to recognize the phone
i guess i shouldve mentioned this earlier, i attempted to flash in Odin but it was stuck on zImage so i unplugged it
before i flashed in odin, i used to be able to boot into the phone like touchwiz and whatnot, now it just gets stuck on the samsung galaxy s ii boot logo
This is now [Solved}! thanks for the help creepyncrawly! i figured it out after doing some more reasearch online. apparently, youre not supposed to use the charger wire that came with the device since samsung doesnt want to waste their time on creating a good enough cable for this kind of stuff. so i grabbed some random cable that i found in my house, hooked it up and BAM! both of my computers were able to detect my phone just finished flashing bone stock on the phone thanks
I noticed in your post that you tried everything but another cable. But I'm glad you got it working. I had the same problem before too. Cables are finicky little things.
Sent from my SGH-I777 using xda app-developers app
Hello,
I've read random threads for the entire day but I'm a bit confused about how to proceed.
cm wiki requires the phone to have stock ICS
I remember something about the baseband, using russian Windows tools to update
I don't have Windows
I'm running osx 10.9.4.
What should I do? I'm also afraid of the superbrick bug.
What I've done:
got root with zergRush
tried to install CWM through ROM Manager, got custom recovery 2.5.1.2 (useless? very old?) but can't boot into recovery, first error was something about signature, when rebooting with volume up+home+power I get "can't access to system/csc/hui/system" instead
I tried then updating stock fw with kies for osx; i was stuck in "connecting" forever
tried installing kies in a windows vm; it couldn't even see the phone and failed to recognize it as a media device
What I know:
I can probably obtain a temporary cwm 6.* (supposed to be not affected by superbrick bug) by loading a zip through stock recovery mode
What I would like:
finally get KK
avoid windows
avoid heimdall; i have bad experience and could never compile it, months ago
avoid yellow triangle
BUT
If heimdall is now a working software and It solves everything (baseband included) by running a one line command, it is a welcomed solution.
Thank you!
p.s. hope I'm in the right forum section
You have really old recovery.
If you want to get newest recovery and avoid windows and have root as you said use Mobile Odin pro to flash the newest CWM (6.0.4.5 I think) and afhter that flash CM via new recovery
I don't know why ROM manager installed something so old.
I thought about Mobile Odin. Does it fix the baseband problem?
ROM managers etc. is balast which made a lot of problems. Don´t be lazy and flash manully
Hey guys, I dug out my old i605 the other day and wanted to update to the latest cm nightly for the device. Not realizing I was about to do something wrong, I downloaded an app called Flashify and installed the latest cm recovery through the app. Well this made my device boot loop. So now, I need to flash a working recovery to my device to fix it. After googling for a bit, I learned that I need Odin to do so. So I am now using Odin v3.10.7. But, I cannot get any recovery tars I've found to flash. They all come back as failed. I'm at a loss here and hope someone knows how to get this thing back up and running.
My PC is on Windows 10 and I do have the latest Samsung drivers installed. On my Note 2 in download mode, it says my current binary is Samsung Official and my system status is custom. What I do not know is what recovery and firmware my i605 was on previously.
Thanks guys
EDIT: I guess what I'd really like to do is get the device back to stock rooted.
Edit 2: Fixed the problem. Uninstalled the Samsung drivers and reinstalled them and changed to Odin 3.07. Ended up restoring the device with the unlocked bootloader restore here: http://forum.xda-developers.com/showthread.php?t=2040264