Hi, can anyone help me?
Samsung S4 Mini (GT-I9192) is stuck on boot logo, after unexpectedly turned off on normal android update. Tried so many tutorials but nothing works. Nothing!
Here goes all info I can think about it:
- Download Mode shows up exacly that:
ODIN MODE
PRODUCT NAME: GT-I9192
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Official
KNOX KERNEL LOCK: 0x0
KNOX WARRANTY VOID: 0x0
CSB-CONFIG-LSB:0x30
BOOTLOADER AP SWREV: 2
WRITE PROTECTION: Enable
- If I try to "wipe/datafactory reset", gives me error:
# MANUAL MODE #
-- Apling Multi-CSC...
Applied the CSC-code : ZT0
Sucessfully applied multi-CSC.
-- Wiping data...
Formatting /data...
E:format_volume: make_extf4fs failed on /dev/block/platform/msm_sdcc.1/by-name/userdata
Formatting /cache...
E:format_volume: make_extf4fs failed on /dev/block/platform/msm_sdcc.1/by-name/cache
Data wipe complete.
Can someone help me? Thanks!
Anyone can help me? Thanks!
Seems that nobody will help me... too bad.
after further testing and finally restoring my IMEIs using this rom, i can say that it is indeed working, so hope it helps a lot of you guys stuck with a phone without IMEIs.
link :
Xiaomi Redmi 9 ENG Firmware (Engineering Rom)
MediaFire is a simple to use free service that lets you put all your photos, documents, music, and video in a single place so you can access them anywhere and share them everywhere.
www.mediafire.com
Requirements:
- SP flash tool and right DA file (provided in the post).
-brom bypass (also provided).
-patience and perseverance.
Steps to install:
1)steps to install brom bypass:
-first install python 3 (check on google)
- then run this code in a cmd
Code:
pip install pyusb pyserial json5
-after that make sure to have all the mediatek drivers installed and install libusb from the archive i provided
- after installing libusb you will be greeted by a filter wizard window, check the "install new device filter" then connect the phone to the pc while pressing (volume +, volume - and power button) all at the same time you
will see in the list a new mtk com port appear click on it and then on install, done with the prep'.
2)steps to flash:
-first launch the brom bypass, a window will appear saying 'waiting for bootrom' connect your phone while pressing (volume +, volume - and power button) all together then you will see on the command prompt 'protection disabled' it means you have successfully bypassed the brom.
- now oppen up sp flash tool, select the download agent, select the scatter fille from the rom folder and the auth file (provided with sp flash tool archive on the post) then setup sp flash tool in uart mode with a bud rate of 921600 then flash in format all.
-done.
Hope this helped, cheers !
Thanks Bro <3
Sammar Prince said:
Thanks Bro <3
Click to expand...
Click to collapse
No problem
razers211 said:
after further testing and finally restoring my IMEIs using this rom, i can say that it is indeed working, so hope it helps a lot of you guys stuck with a phone without IMEIs.
link :
Xiaomi Redmi 9 ENG Firmware (Engineering Rom)
MediaFire is a simple to use free service that lets you put all your photos, documents, music, and video in a single place so you can access them anywhere and share them everywhere.
www.mediafire.com
Requirements:
- SP flash tool and right DA file (provided in the post).
-brom bypass (also provided).
-patience and perseverance.
Steps to install:
1)steps to install brom bypass:
-first install python 3 (check on google)
- then run this code in a cmd
Code:
pip install pyusb pyserial json5
-after that make sure to have all the mediatek drivers installed and install libusb from the archive i provided
- after installing libusb you will be greeted by a filter wizard window, check the "install new device filter" then connect the phone to the pc while pressing (volume +, volume - and power button) all at the same time you
will see in the list a new mtk com port appear click on it and then on install, done with the prep'.
2)steps to flash:
-first launch the brom bypass, a window will appear saying 'waiting for bootrom' connect your phone while pressing (volume +, volume - and power button) all together then you will see on the command prompt 'protection disabled' it means you have successfully bypassed the brom.
- now oppen up sp flash tool, select the download agent, select the scatter fille from the rom folder and the auth file (provided with sp flash tool archive on the post) then setup sp flash tool in uart mode with a bud rate of 921600 then flash in format all.
-done.
Hope this helped, cheers !
Click to expand...
Click to collapse
Help sir, how to fix this error? Thanks
razers211 said:
after further testing and finally restoring my IMEIs using this rom, i can say that it is indeed working, so hope it helps a lot of you guys stuck with a phone without IMEIs.
link :
Xiaomi Redmi 9 ENG Firmware (Engineering Rom)
MediaFire is a simple to use free service that lets you put all your photos, documents, music, and video in a single place so you can access them anywhere and share them everywhere.
www.mediafire.com
Requirements:
- SP flash tool and right DA file (provided in the post).
-brom bypass (also provided).
-patience and perseverance.
Steps to install:
1)steps to install brom bypass:
-first install python 3 (check on google)
- then run this code in a cmd
Code:
pip install pyusb pyserial json5
-after that make sure to have all the mediatek drivers installed and install libusb from the archive i provided
- after installing libusb you will be greeted by a filter wizard window, check the "install new device filter" then connect the phone to the pc while pressing (volume +, volume - and power button) all at the same time you
will see in the list a new mtk com port appear click on it and then on install, done with the prep'.
2)steps to flash:
-first launch the brom bypass, a window will appear saying 'waiting for bootrom' connect your phone while pressing (volume +, volume - and power button) all together then you will see on the command prompt 'protection disabled' it means you have successfully bypassed the brom.
- now oppen up sp flash tool, select the download agent, select the scatter fille from the rom folder and the auth file (provided with sp flash tool archive on the post) then setup sp flash tool in uart mode with a bud rate of 921600 then flash in format all.
-done.
Hope this helped, cheers !
Click to expand...
Click to collapse
Help sir, how to fix this error? Thanks
razers211 said:
after further testing and finally restoring my IMEIs using this rom, i can say that it is indeed working, so hope it helps a lot of you guys stuck with a phone without IMEIs.
link :
Xiaomi Redmi 9 ENG Firmware (Engineering Rom)
MediaFire is a simple to use free service that lets you put all your photos, documents, music, and video in a single place so you can access them anywhere and share them everywhere.
www.mediafire.com
Requirements:
- SP flash tool and right DA file (provided in the post).
-brom bypass (also provided).
-patience and perseverance.
Steps to install:
1)steps to install brom bypass:
-first install python 3 (check on google)
- then run this code in a cmd
Code:
pip install pyusb pyserial json5
-after that make sure to have all the mediatek drivers installed and install libusb from the archive i provided
- after installing libusb you will be greeted by a filter wizard window, check the "install new device filter" then connect the phone to the pc while pressing (volume +, volume - and power button) all at the same time you
will see in the list a new mtk com port appear click on it and then on install, done with the prep'.
2)steps to flash:
-first launch the brom bypass, a window will appear saying 'waiting for bootrom' connect your phone while pressing (volume +, volume - and power button) all together then you will see on the command prompt 'protection disabled' it means you have successfully bypassed the brom.
- now oppen up sp flash tool, select the download agent, select the scatter fille from the rom folder and the auth file (provided with sp flash tool archive on the post) then setup sp flash tool in uart mode with a bud rate of 921600 then flash in format all.
-done.
Hope this helped, cheers !
Click to expand...
Click to collapse
Hi thank you i was succesfuly installed this rom and now what to restore IMEI? AT commands not working it says +CME ERROR: 100
thank you in advice i was tryed a lot of forms and i cant make calls, only 4G and SMS, restricted calls
yoalcuadrao said:
thank you in advice i was tryed a lot of forms and i cant make calls, only 4G and SMS, restricted calls
Click to expand...
Click to collapse
don't restore the imei 1 of the phone and put your sim in slot 2, might work now
willkurt27 said:
Help sir, how to fix this error? Thanks
Click to expand...
Click to collapse
did you properly install the mtk drivers ???
Well i hope i would be finally able to unbrick my phone with this... No recovery and fastoboot and by far everything works my device is recognized as mtk device but cannot flash any stock rom with SM Flash Tool
razers211 said:
after further testing and finally restoring my IMEIs using this rom, i can say that it is indeed working, so hope it helps a lot of you guys stuck with a phone without IMEIs.
link :
Xiaomi Redmi 9 ENG Firmware (Engineering Rom)
MediaFire is a simple to use free service that lets you put all your photos, documents, music, and video in a single place so you can access them anywhere and share them everywhere.
www.mediafire.com
Requirements:
- SP flash tool and right DA file (provided in the post).
-brom bypass (also provided).
-patience and perseverance.
Steps to install:
1)steps to install brom bypass:
-first install python 3 (check on google)
- then run this code in a cmd
Code:
pip install pyusb pyserial json5
-after that make sure to have all the mediatek drivers installed and install libusb from the archive i provided
- after installing libusb you will be greeted by a filter wizard window, check the "install new device filter" then connect the phone to the pc while pressing (volume +, volume - and power button) all at the same time you
will see in the list a new mtk com port appear click on it and then on install, done with the prep'.
2)steps to flash:
-first launch the brom bypass, a window will appear saying 'waiting for bootrom' connect your phone while pressing (volume +, volume - and power button) all together then you will see on the command prompt 'protection disabled' it means you have successfully bypassed the brom.
- now oppen up sp flash tool, select the download agent, select the scatter fille from the rom folder and the auth file (provided with sp flash tool archive on the post) then setup sp flash tool in uart mode with a bud rate of 921600 then flash in format all.
-done.
Hope this helped, cheers !
Click to expand...
Click to collapse
thank very much bro
muito obrigado, tive que usar o META modem para escrever IMEI. so deu certo com essa room, deus te abençoe. BRASIL
----------
MOD EDIT: English Translation Below
thank you very much, had to use META modem to write IMEI. it just worked out with this room, god bless you. BRAZIL
tiagoql said:
muito obrigado, tive que usar o META modem para escrever IMEI. so deu certo com essa room, deus te abençoe. BRASIL
Click to expand...
Click to collapse
in english or indonesia please
hello if I flash this rom to my miui 12.5.1 will this work? or my phone will be stucked in bootloop? sorry im newbie
work.
only write imei simcard 2 brother
razers211 said:
after further testing and finally restoring my IMEIs using this rom, i can say that it is indeed working, so hope it helps a lot of you guys stuck with a phone without IMEIs.
link :
Xiaomi Redmi 9 ENG Firmware (Engineering Rom)
MediaFire is a simple to use free service that lets you put all your photos, documents, music, and video in a single place so you can access them anywhere and share them everywhere.
www.mediafire.com
Click to expand...
Click to collapse
Hello and thanks for sharing, I have the same error as @willkurt27
while using SPFlash Tool
What I do:
Launch bypass.bat
Plug my phone with vol - pressed and battery unplugged.
[2021-08-24 21:33:09.958798] Waiting for device
[2021-08-24 21:39:08.793257] Found device = 0e8d:0003
[2021-08-24 21:39:14.833772] Device hw code: 0x707
[2021-08-24 21:39:14.833772] Device hw sub code: 0x8a00
[2021-08-24 21:39:14.833772] Device hw version: 0xca00
[2021-08-24 21:39:14.833772] Device sw version: 0x0
[2021-08-24 21:39:14.833772] Device secure boot: True
[2021-08-24 21:39:14.833772] Device serial link authorization: True
[2021-08-24 21:39:14.833772] Device download agent authorization: True
[2021-08-24 21:39:14.833772] Disabling watchdog timer
[2021-08-24 21:39:14.849712] Disabling protection
[2021-08-24 21:39:14.849712] Using kamakiri
[2021-08-24 21:39:14.849712] Protection disabled
Appuyez sur une touche pour continuer...
Then I use SPFlash Tool v5.1924.0
Tried with DA_6765_6785_6768_6873_6885_6853.bin and MTK_AllInOne_DA.bin
What am I doing wrong?
hckbkl said:
work.
only write imei simcard 2 brother
Click to expand...
Click to collapse
which da will i use? DA_6765_6785_6768_6873_6885_6853 or MTK_AllInOne_DA for redmi 9 mt6768
lobothefoots said:
Hello and thanks for sharing, I have the same error as @willkurt27
while using SPFlash Tool
What I do:
Launch bypass.bat
Plug my phone with vol - pressed and battery unplugged.
[2021-08-24 21:33:09.958798] Waiting for device
[2021-08-24 21:39:08.793257] Found device = 0e8d:0003
[2021-08-24 21:39:14.833772] Device hw code: 0x707
[2021-08-24 21:39:14.833772] Device hw sub code: 0x8a00
[2021-08-24 21:39:14.833772] Device hw version: 0xca00
[2021-08-24 21:39:14.833772] Device sw version: 0x0
[2021-08-24 21:39:14.833772] Device secure boot: True
[2021-08-24 21:39:14.833772] Device serial link authorization: True
[2021-08-24 21:39:14.833772] Device download agent authorization: True
[2021-08-24 21:39:14.833772] Disabling watchdog timer
[2021-08-24 21:39:14.849712] Disabling protection
[2021-08-24 21:39:14.849712] Using kamakiri
[2021-08-24 21:39:14.849712] Protection disabled
Appuyez sur une touche pour continuer...
Then I use SPFlash Tool v5.1924.0
Tried with DA_6765_6785_6768_6873_6885_6853.bin and MTK_AllInOne_DA.bin
View attachment 5392951
What am I doing wrong?
Click to expand...
Click to collapse
try to insert the auth file
lobothefoots said:
Hello and thanks for sharing, I have the same error as @willkurt27
while using SPFlash Tool
What I do:
Launch bypass.bat
Plug my phone with vol - pressed and battery unplugged.
[2021-08-24 21:33:09.958798] Waiting for device
[2021-08-24 21:39:08.793257] Found device = 0e8d:0003
[2021-08-24 21:39:14.833772] Device hw code: 0x707
[2021-08-24 21:39:14.833772] Device hw sub code: 0x8a00
[2021-08-24 21:39:14.833772] Device hw version: 0xca00
[2021-08-24 21:39:14.833772] Device sw version: 0x0
[2021-08-24 21:39:14.833772] Device secure boot: True
[2021-08-24 21:39:14.833772] Device serial link authorization: True
[2021-08-24 21:39:14.833772] Device download agent authorization: True
[2021-08-24 21:39:14.833772] Disabling watchdog timer
[2021-08-24 21:39:14.849712] Disabling protection
[2021-08-24 21:39:14.849712] Using kamakiri
[2021-08-24 21:39:14.849712] Protection disabled
Appuyez sur une touche pour continuer...
Then I use SPFlash Tool v5.1924.0
Tried with DA_6765_6785_6768_6873_6885_6853.bin and MTK_AllInOne_DA.bin
View attachment 5392951
What am I doing wrong?
Click to expand...
Click to collapse
or install mtk drivers properly
lobothefoots said:
Hello and thanks for sharing, I have the same error as @willkurt27
while using SPFlash Tool
What I do:
Launch bypass.bat
Plug my phone with vol - pressed and battery unplugged.
[2021-08-24 21:33:09.958798] Waiting for device
[2021-08-24 21:39:08.793257] Found device = 0e8d:0003
[2021-08-24 21:39:14.833772] Device hw code: 0x707
[2021-08-24 21:39:14.833772] Device hw sub code: 0x8a00
[2021-08-24 21:39:14.833772] Device hw version: 0xca00
[2021-08-24 21:39:14.833772] Device sw version: 0x0
[2021-08-24 21:39:14.833772] Device secure boot: True
[2021-08-24 21:39:14.833772] Device serial link authorization: True
[2021-08-24 21:39:14.833772] Device download agent authorization: True
[2021-08-24 21:39:14.833772] Disabling watchdog timer
[2021-08-24 21:39:14.849712] Disabling protection
[2021-08-24 21:39:14.849712] Using kamakiri
[2021-08-24 21:39:14.849712] Protection disabled
Appuyez sur une touche pour continuer...
Then I use SPFlash Tool v5.1924.0
Tried with DA_6765_6785_6768_6873_6885_6853.bin and MTK_AllInOne_DA.bin
View attachment 5392951
What am I doing wrong?
Click to expand...
Click to collapse
use mtkbypass
Hey everyone, I am trying to flash my SM-G9650 with TWRP but both Odin and Heimdall fail in doing so. I've tried Odin on Windows 10 (with Samsung drivers), Heimdall on Windows 10 (with WinUSB or LibUSBk) and even Heimdall on Manjaro Linux (with libusb) but none work. They all either hang at initialising, during initialising, or just fail with no error (Odin). For instance, Heimdall on Manjaro Linux gives this:
Code:
Heimdall v1.4.2
Copyright (c) 2010-2017 Benjamin Dobell, Glass Echidna
http://www.glassechidna.com.au/
This software is provided free of charge. Copying and redistribution is
encouraged.
If you appreciate this software and you would like to support future
development please consider donating:
http://www.glassechidna.com.au/donate/
Initialising connection...
Detecting device...
Claiming interface...
Setting up interface...
Initialising protocol...
ERROR: Failed to send handshake!ERROR: Protocol initialisation failed!
Releasing device interface...
And this is what appears on my download mode:
Code:
RPMB fuse blown
RPMB Provisioned
CURRENT BINARY:Samsung Official
OEM LOCK: OFF
REACTIVATION LOCK: OFF
WARRANTY VOID: 0X0
QUALCOMM SECUREBOOT: ENABLE
RP SWREV : b9(2,2,2,9,2) K9 S9
SECURE DOWNLOAD: ENABLE
DID: 20208B2BEA756311
I've tried the usual, different USB ports, cables, restarting PC, but nothing makes the trick. I even tried to flash the official Samsung firmware, same bit (9) and everything but still, nothing. Both OEM Unlock and USB Debugging are enabled, and I think I don't need to use CROM Service anymore, and if I do I'm in an uncomfortable situation because it doesn't even open on my Android 10 firmware...
frangamer18922 said:
Hey everyone, I am trying to flash my SM-G9650 with TWRP but both Odin and Heimdall fail in doing so. I've tried Odin on Windows 10 (with Samsung drivers), Heimdall on Windows 10 (with WinUSB or LibUSBk) and even Heimdall on Manjaro Linux (with libusb) but none work. They all either hang at initialising, during initialising, or just fail with no error (Odin). For instance, Heimdall on Manjaro Linux gives this:
Code:
Heimdall v1.4.2
Copyright (c) 2010-2017 Benjamin Dobell, Glass Echidna
http://www.glassechidna.com.au/
This software is provided free of charge. Copying and redistribution is
encouraged.
If you appreciate this software and you would like to support future
development please consider donating:
http://www.glassechidna.com.au/donate/
Initialising connection...
Detecting device...
Claiming interface...
Setting up interface...
Initialising protocol...
ERROR: Failed to send handshake!ERROR: Protocol initialisation failed!
Releasing device interface...
And this is what appears on my download mode:
Code:
RPMB fuse blown
RPMB Provisioned
CURRENT BINARY:Samsung Official
OEM LOCK: OFF
REACTIVATION LOCK: OFF
WARRANTY VOID: 0X0
QUALCOMM SECUREBOOT: ENABLE
RP SWREV : b9(2,2,2,9,2) K9 S9
SECURE DOWNLOAD: ENABLE
DID: 20208B2BEA756311
I've tried the usual, different USB ports, cables, restarting PC, but nothing makes the trick. I even tried to flash the official Samsung firmware, same bit (9) and everything but still, nothing. Both OEM Unlock and USB Debugging are enabled, and I think I don't need to use CROM Service anymore, and if I do I'm in an uncomfortable situation because it doesn't even open on my Android 10 firmware...
Click to expand...
Click to collapse
Did you manage to find out what the problem was? I have a similar situation with a Note 10+. I am starting to suspect that Samsung made it unflashable after certain update, like i've read som devices can be..
And by the way how did you manage to flash official firmware?