Related
Please help to root this phone!!!!!!!!
Мукеуз said:
Please help to root this phone!!!!!!!!
Click to expand...
Click to collapse
need to up this thread mmm... anybody know to to root this alcatel 985n
ROOTING Alcatel 985 SUCCESS Step by step tutorial
MARLBORO_R3D said:
need to up this thread mmm... anybody know to to root this alcatel 985n
Click to expand...
Click to collapse
Ok.. Hi everybody..
I'm a bit new at this so bare with me....
To root the 985 you basically need this:
- Installed Drivers VERY IMPORTANT!
- Installed ADB shell (To open ADB command prompt go into the install folder of adb -> sdk -> platform tools -> hold SHIFT and right click -> select open command prompt window here) - this was the command line for me - for you it might be different!
- Create ROM backup following these instructions:
- Open ADB command prompt (described above) and enter adb shell cat /proc/mtd
- If all goes well copy the results into notepad and save the file as firmware.info
- After that open MTK 65xx ROM Studio
- Go File -> Load Firmware.info -> select the file you generated earlier
- Notice that the window is now filled with data from your file -> click Create ROM
- Now save that file somewhere easily accessible it's your SCATTER file needed a bit later.
- Open SP Flash Tool (Make sure MT 65x3 USB VCOM drivers are installed )
- Go Options -> USB Mode
- Then press SCATTER-LOADING to the right and select your SCATTER file generated earlier (ignore messages)
- Go into the read-back tab
- Select every checkbox (to make FULL Backup,) or just what you need (Bootimg.img) select where to save Backup!
- When the windows appear make sure that READ PAGE ONLY is selected!
- Press READ BACK (by this point your phone hasn't been connected at all to the PC)
- Now turn off your phone, pull out the battery,hold VOLUME UP, plug the phone in and THEN quickly put the battery back in!!!
- If all goes well you should see one red bar and one or several blue ones (depending on what you selected to backup)
- This can take a while, BOOM Green circle
- BACKUP IS DONE!
- Now on to the rooting stuff:
- In SP Flash Tool (I am expecting that you closed it and opened it again)
- Check to see if USB Mode is enabled (see above)
- Load the SCATTER file again
- Then when you see the files and checkboxes in the window under click on BOOTIMG and SELECT the one
that is attached to this post (!!!!NOTE This is the same BOOTIMG from the serbian video on youtube WE ONLY NEED THE BOOTIMG FROM THIS GUY NOTHING ELSE ESPECIALLY NOT THE SCATTER!!!!)
- Ignore the following messages
- Make sure that your phone is not plugged in, turned off and battery removed
- Press Download, wait 15 sec, plug the phone in THEN insert battery
- Wait for it.. (Nice one)
- A yellow bar will go across and BOOM Green circle
AT THIS POINT YOU HAVE FLASHED YOUR BOOTIMG IF YOU HAVE DONE THIS RIGHT THERE WOULD BE NO PROBLEMS, IF IT'S DONE WRONG YOUR PHONE MIGHT NOT RECOGNIZE THE SIM CARD (IF THIS HAPPENS DO THE LAST STEP AGAIN BUT WITH THE BOOTIMG FROM THE BACKUP)
- Unplug phone, remove battery, insert battery -> BOOT
If it boots, OK, if not flash back with backup (see above written in BIG letters
- Download SuperOneClick and open it
- Plug in your phone TURNED ON!
- Click Root. Reboot. DONE
If anything else pops up you have a problem with the drivers make sure that the drivers are correctly installed (stupid Windows rrrr...)
Now you have rooted you ALCATEL OT-985n/d and can do all kinds of crazy stuff... :cyclops:
DISCLAIMER:
I AM NOT RESPONSIBLE FOR THE DAMAGE TO YOUR PHONE, YOU, OR ANY OTHER MEMBER OF YOUR FAMILY.
WON'T BE HELD AT CHARGE IF YOUR PHONE BLOWS UP, FALLS DOWN AND ERRADICATES HALF OF THE HUMAN RACE AS A RESULT OF MOLECULAR MUTATION CAUSED BY THE GAMA RADIATION BLA BLA YOU GET MY DRIFT..
THIS POST IS A RESULT FROM VARIOUS POSTS (and screwing up my phone multiple times) PUT TOGETHER IN THE METHOD THAT WORKED FOR ME!
CREDITS:
WOULD LIKE TO THANK
giuaig - this is all yours buddy :good
and every other member that banged their head at this for days.. screwed up their phone at least twice and had the nerve to cope!
Bye everybody
Need help in restoring Android and custpack
Hi everybody!
I need some help to restore my 985. I succeeded rooting the phone with this great guide but I messed up with /custpack trying to remove some factory apps (facebook, operator apps...) with the result of having an unusable device stuck in the boot process and rebooting before the system is up in an infinite cycle.
I tried to restore my custpack backup made before rooting with no results. After some whole nights spent asleep to find factory ROM or updates
which seems can't be found on the net, I took the fool decision to format the whole ROM trying to make One Touch Updater S search the firmware and restore the phone but it didn't, leaving me with a message like "You already got the latest version for your phone" (kidding?).
I managed to restore some partition backups with SP Flash Tool. Now the phone can turn on, show the battery-charging logo, the android logo and the recovery system. But it won't boot in normal mode: it gets stuck at the Android logo with no further steps. ADB can discover and recognise the stuck device, but won't let me reach a shell ("/system/bin/sh not found" or something similar). SPFT seems to let me download the Android and custpack images but at the end it fires an error about DRAM.
Is there any Alcatel One Touch 985 user that can send me Android and custpack images to restore my phone?
Hallo guys. Thanks for opening this thread.
My OT985 is stuffed with bloatware from an Italian Carrier, that makes it impossible to download updates and new apps (I can't even download G+).
Do you think that flashing an original stock rom will fix my issue? Does anybody out there have a non-branded backup rom I could possibly use?
Thank you for any help and replies.
AlcaWel said:
Hi everybody!
I need some help to restore my 985. I succeeded rooting the phone with this great guide but I messed up with /custpack trying to remove some factory apps (facebook, operator apps...) with the result of having an unusable device stuck in the boot process and rebooting before the system is up in an infinite cycle.
I tried to restore my custpack backup made before rooting with no results. After some whole nights spent asleep to find factory ROM or updates
which seems can't be found on the net, I took the fool decision to format the whole ROM trying to make One Touch Updater S search the firmware and restore the phone but it didn't, leaving me with a message like "You already got the latest version for your phone" (kidding?).
I managed to restore some partition backups with SP Flash Tool. Now the phone can turn on, show the battery-charging logo, the android logo and the recovery system. But it won't boot in normal mode: it gets stuck at the Android logo with no further steps. ADB can discover and recognise the stuck device, but won't let me reach a shell ("/system/bin/sh not found" or something similar). SPFT seems to let me download the Android and custpack images but at the end it fires an error about DRAM.
Is there any Alcatel One Touch 985 user that can send me Android and custpack images to restore my phone?
Click to expand...
Click to collapse
I think I have a backup but I'm new and can't post links... I'll be back!
help me for mt65x3 driver
hi all,
i need help for installing the mt65x3 driver.
My ot 985d has USB\Vid_1bbb&Pid_00f2&Rev_0255&MI_01
USB\Vid_1bbb&Pid_00f2&MI_01
this device is by Mt65x3 Driver Installation not suported.
Sorry for my bad english, im for german
Thanks for our help ! ! !
Hi to all . Is there any user of 985d who can back up and send me the original boot.img of the device?
Hi all,
first I was runing into numerous problems with this guide, so I switched to this one and I managed to do a lot more: http://forum.xda-developers.com/showpost.php?p=38337401&postcount=5
But with that other guide, I couldn't go further than step 8, because error "PMT changed for the ROM, it must be downloaded." would pop-up.
The same would happen if I followed the steps after "Now onto the rooting stuff" - the error "PMT changed for the ROM, it must be downloaded." pops-up instead of a "green circle".
Can anyone help resolve this?
Hi everyone,
I have a Sony Tablet S with Android Version 4.0.3 release 5a and I am having problems with the Android Software, the programs such as browser, games even android base applications keep crashing. The device is still under warranty and I sent it for repair however the service here requested around 100$ for software installation as it is not under warranty. This is too much for me so I decided to do it myself however. I have searched this forum and many more to find a solution however even I have tried every step described in forums several time I could not be able to reinstall latest ROM from SD Card. I really desperately need some help here as this device is purchased solely for my daughter who loves android games alot.
I really appreciate any help you may provide.
Thanks.
Aktemur said:
Hi everyone,
I have a Sony Tablet S with Android Version 4.0.3 release 5a and I am having problems with the Android Software, the programs such as browser, games even android base applications keep crashing. The device is still under warranty and I sent it for repair however the service here requested around 100$ for software installation as it is not under warranty. This is too much for me so I decided to do it myself however. I have searched this forum and many more to find a solution however even I have tried every step described in forums several time I could not be able to reinstall latest ROM from SD Card. I really desperately need some help here as this device is purchased solely for my daughter who loves android games alot.
I really appreciate any help you may provide.
Thanks.
Click to expand...
Click to collapse
hello,
try a hard reset. hold VOL up + POWER and when you see the logo sony release the VOL up button. then choose a factory reset. do not have to install from sd card.
Already tried hard and soft reset. Doesn't work.
I will try to describe the problem in full detail. I have weird error messages like "Google Play Store stopped working" "browser stopped working" "clock stopped working" and such error messages and when I try to uninstall programs i can uninstall them however when the tablet restarts they are all there, I think machine resets it self. If i try to uninstall a program called "Ustream" the tablet immediately goes off, and restarts resetting it self again. Even the soft and hard reset can not solve the problem. I have tried to boot the device, it says it is booted (I have managed to run adb and flash tools) how ever when the tablet restarts it again resets it self having the exact same situation as before. I have downloaded the official R5A update from the Sony Website when ever i try to install update from SD, the machine stops saying the operation is aborted due to some error. There must be a way to reset this machine to what ever it was.
Aktemur said:
I will try to describe the problem in full detail. I have weird error messages like "Google Play Store stopped working" "browser stopped working" "clock stopped working" and such error messages and when I try to uninstall programs i can uninstall them however when the tablet restarts they are all there, I think machine resets it self. If i try to uninstall a program called "Ustream" the tablet immediately goes off, and restarts resetting it self again. Even the soft and hard reset can not solve the problem. I have tried to boot the device, it says it is booted (I have managed to run adb and flash tools) how ever when the tablet restarts it again resets it self having the exact same situation as before. I have downloaded the official R5A update from the Sony Website when ever i try to install update from SD, the machine stops saying the operation is aborted due to some error. There must be a way to reset this machine to what ever it was.
Click to expand...
Click to collapse
If you have adb, you can try to root tab and apply the backdoor patch.
Sony Tablet S cihazımdan Tapatalk kullanılarak gönderildi
smgdev said:
If you have adb, you can try to root tab and apply the backdoor patch.
Sony Tablet S cihazımdan Tapatalk kullanılarak gönderildi
Click to expand...
Click to collapse
I have already tried that. The adb, flasher and other tools that I have found in this site. All in one tool says it has succesfully rooted the device but whenever it boots it restores itself to a previous unknown backup with all the applications installed and I guess not rooted state. I have used the flasher yet it needs rooted device. I have tried to update the system from SD, it says the software is low version (5A). I can not do anything. There must be a solution for this.
Aktemur said:
I have already tried that. The adb, flasher and other tools that I have found in this site. All in one tool says it has succesfully rooted the device but whenever it boots it restores itself to a previous unknown backup with all the applications installed and I guess not rooted state. I have used the flasher yet it needs rooted device. I have tried to update the system from SD, it says the software is low version (5A). I can not do anything. There must be a solution for this.
Click to expand...
Click to collapse
After attempting root the tablet is rebooting into the other partition. (There are two system partitions). Can you try rooting again and on the last reboot boot into recovery and try to install R5a twice in a row without restarting from the recovery menu. Hopefully this will catch the system switch and install R5a on the other system
stifilz said:
After attempting root the tablet is rebooting into the other partition. (There are two system partitions). Can you try rooting again and on the last reboot boot into recovery and try to install R5a twice in a row without restarting from the recovery menu. Hopefully this will catch the system switch and install R5a on the other system
Click to expand...
Click to collapse
I think I have rooted the device asthere is a "device manager" in the security options. However adb programs fails to recognize the device. I have installed the driver several times, restarted the computer how ever it did not change. Last time I was able to see the device in the adb device list. But i do not know what I have done to achieve this as I have tired many options. Can you describe me how to do that step by setp?
Aktemur said:
I think I have rooted the device asthere is a "device manager" in the security options. However adb programs fails to recognize the device. I have installed the driver several times, restarted the computer how ever it did not change. Last time I was able to see the device in the adb device list. But i do not know what I have done to achieve this as I have tired many options. Can you describe me how to do that step by setp?
Click to expand...
Click to collapse
EDIT: I have AIO tools and flasher and ADB automatic driver instlaller. Now ADB Automatic installer worked just fine the adb devices i can see the device serial number. There is an "android device manager" option which I have enabled from security settings in my tablet. USB debugging mode is active however the S.onyTablet.S allinone v6.5 by konrad plasczykowski can not flash the tablet, it can not find the tablet. when i boot in to recover i have 3 options listed.
1. restart device
2 update sysstem from SD cARD
3 Reset to factory settings
when i choose update system from SD cart i see" Erohibit update as a result of checking versdion or base sku insallation aborted." message what does that mean?
there are no other options. how can i continue on...
Aktemur said:
EDIT: I have AIO tools and flasher and ADB automatic driver instlaller. Now ADB Automatic installer worked just fine the adb devices i can see the device serial number. There is an "android device manager" option which I have enabled from security settings in my tablet. USB debugging mode is active however the S.onyTablet.S allinone v6.5 by konrad plasczykowski can not flash the tablet, it can not find the tablet. when i boot in to recover i have 3 options listed.
1. restart device
2 update sysstem from SD cARD
3 Reset to factory settings
when i choose update system from SD cart i see" Erohibit update as a result of checking versdion or base sku insallation aborted." message what does that mean?
there are no other options. how can i continue on...
Click to expand...
Click to collapse
After the update fail. Use adb pull /tmp/recovery.log and post it here and I will see what is happening
The flashing operation fails as the system can not access to the specified directory. Whenever I run the flashing tool the command windows background turns to red and I see this error. ADB can list the device yet I can not flash it.
By the way I have to reinstall all the drivers everytime I connect the tablet to PC, if I remove the cable and re mount it adb fails to list the device.
Hello guys, it's nice to be part of this great community. My English are not that good so please be patient with my explanations.
Well , I'm quite desperate here. A friend of mine gave me this phone (Xiaomi Redmi 1) bricked.
First of all the mobile can't boot, it says tool dl image fail. Even worst I can't even select the options in the boot menu, the tool dl image fail appears again. That means the memory is almost empty...
According to my experience the solution was only 1, Flash tools.
But again , I tried the Firmware/Update option of these ROMs: Xiaomi Hongmi WCDMA (HM2013023_images_JHBCNAL5.0_4.2)/ TD (Hongmi_images_HBJ2.02_4.2) - unbrick 5.0 and....NOTHING!
If I choose the download option but the bar reaches only 1% and theen I have this : s_ft_download_fail (4008). I tried the HM2013023_images_JHBCNAH4.0_4.2 but with the same results.
An extra detail is that IF I choose the format option, althought it doesn't complete...my mobile doesn't open after that. In order to be working again, I just have to choose the download option (till the 1%) and the it boots with the above problems.
To be more clear I installed the necessary drivers, I removed them, I installed them again...NOTHING. I changed the USB port, the same results..
An interesting quotation is that if I try to connect the device with a different USB cable that the original, the pc doesn't even recognize it (mobile). Also, I've noticed that the flash tools cannot install these (from the scatter) : Android, Cache, UserData & Fat.
As for the CMW Recovery ... no luck at all. They are all in image format which means, I can not install it.
Any help will be appreciated....althought I'm pretty sure the phone is 99% dead..
Any news?
Scattyyy said:
Hello guys, it's nice to be part of this great community. My English are not that good so please be patient with my explanations.
Well , I'm quite desperate here. A friend of mine gave me this phone (Xiaomi Redmi 1) bricked.
First of all the mobile can't boot, it says tool dl image fail. Even worst I can't even select the options in the boot menu, the tool dl image fail appears again. That means the memory is almost empty...
According to my experience the solution was only 1, Flash tools.
But again , I tried the Firmware/Update option of these ROMs: Xiaomi Hongmi WCDMA (HM2013023_images_JHBCNAL5.0_4.2)/ TD (Hongmi_images_HBJ2.02_4.2) - unbrick 5.0 and....NOTHING!
If I choose the download option but the bar reaches only 1% and theen I have this : s_ft_download_fail (4008). I tried the HM2013023_images_JHBCNAH4.0_4.2 but with the same results.
An extra detail is that IF I choose the format option, althought it doesn't complete...my mobile doesn't open after that. In order to be working again, I just have to choose the download option (till the 1%) and the it boots with the above problems.
To be more clear I installed the necessary drivers, I removed them, I installed them again...NOTHING. I changed the USB port, the same results..
An interesting quotation is that if I try to connect the device with a different USB cable that the original, the pc doesn't even recognize it (mobile). Also, I've noticed that the flash tools cannot install these (from the scatter) : Android, Cache, UserData & Fat.
As for the CMW Recovery ... no luck at all. They are all in image format which means, I can not install it.
Any help will be appreciated....althought I'm pretty sure the phone is 99% dead..
Click to expand...
Click to collapse
any news??
I have the phone (hongmi) bricked too....
when I try to use SP Flash tool after choose the correct rom, i try to fix the firmware and after done 100%(red bar) an error comes out (4032)....
My phone sometimes start (but goes in black screen quickly) often NO.... do you have any information for me? Or some other forum that can I check)
Tnx in advance
The definite guide to rooting Samsung Galaxy J3(2016) SM-J320FN & FRP Locked Bootloop
As first I have to say, I had to create a thread in Q&A because of the low rank, but I am sure this can be moved to the J3 section as there are many questions on how to gain root access to this device. This guide can work on the SM-J320F model as well, but it hasn't been tested on other models, so don't try it !
Lets start :
Dont forget to Backup all your data before the process !!!
1. Tick USB Debugging and OEM Unlock in Developer Mode (OEM has to be ticked to unlock the bootloader)
2. Connect to PC with USB Cable and open Odin
3. Power off and reboot into Download Mode (VOL.DOWN+HOME+POWER)
4. Add twrp.zip to AP tab
5. Untick Auto-Reboot and Start
6. Wait to finish
7. When it's finished hold (VOL.DOWN+VOL.UP+HOME+POWER) to Power Off
8. Load into TWRP Mode (VOL.UP+HOME+POWER)
9. In TWRP first go to the Wipe Tab, check Cache and Data and click Wipe
10. Copy SuperSU into internal memory from your PC
11. Go back to TWRP and select Install, select the SuperSU from the internal memory and click install without ticking anything, then reboot
12. Wait for the phone to reboot, it may boot-loop a few times, and it boots slowly but dont interrupt the process !
13. From there on, check the root status by downloading Root Checker from PlayStore
KEEP OEM-UNLOCK ON ALL THE TIME, IF YOU DONT WANNA END UP WITH A BRICKED DEVICE(CUSTOM BINARY WAS BLOCKED BY FRP LOCK)!!!
If that happens, here is an official guide from the Samsung Kies Support Page :
IMPORTANT: You may need your device model name, S/N number, or IMEI number in order to proceed. This information can be found on the label underneath your device battery.
WARNING: This process permanently deletes all personal information from the device. The information will not be recoverable if you proceed with this process.
1. Open Kies 3 and click Tools > Firmware Upgrade and Initialization.
2. Enter your device Model name and click OK.
3. Enter the device S / N number and click OK.
4. Kies 3 will verify that the feature is available for your device. If the feature is available, click OK to continue.
5. The firmware version is displayed along with a note that the information on your device will be permanently deleted during this process. Click OK to continue.
6. Follow the steps to prepare your device for emergency recovery. Mark the checkbox next to I have read all of the above information. Select whether you agree to share this update with Samsung. Connect your device to Kies when you have activated the download mode. When your device is in download mode and connected to Kies 3, the Start upgrade button is available. Click Start upgrade to reinstall the firmware.
7. Touch Create backup to create a copy of selected items before proceeding. Touch Skip backup to proceed without backing up any items.
8. Kies 3 will download and prepare your system to update the firmware. This process can take some time. The time will vary based on your network and computer capabilities.
9. Respond to any security warnings about installing software.
10. The progress screen is shown during the upgrade process. The process will take several minutes to complete. Do not disconnect your device, turn the device off, or turn off your computer during this process.
11. Click OK when the upgrade is finished.
Therefore I provide you all the needed files to do this :
How to root SM-J320FN.rar
Works like a charm on J320FN.
I signed up just to say, after hours of trying different guides, accidentally factory resetting once or twice, and getting my phone stuck in a boot loop, this method worked. BUT it did factory reset my phone, but that's fine I've everything backed up and it wont take long to get it back. Maybe I pressed something I shouldn't have.
Some info on my phone in case it helps anyone in a similar position to how I was:
At one point I installed stock firmware from to get my phone out of the boot loop, I can't link it but if you google "J320FNXXU0APB4_J320FNO2C0APC1_O2C" (WITH quotes) you should find the page.
After doing that:
Android version: 5.1.1
Model number: SM-J320FN
Kernel version: 3.10.65-7225942 (Sun Feb 14 2016)
Build no: LMY47V.J320FNXXU0APB4
Baseband version: J320FNXXU0APB5
I hope I typed all that right. Thank you so much!!
have anyone tried on j320v?
kekambas18 said:
have anyone tried on j320v?
Click to expand...
Click to collapse
Going to attempt that right now wish me luck.
---------- Post added at 08:06 PM ---------- Previous post was at 07:09 PM ----------
And it didn't work. Not suprised, but I at least tried.
GN9166 said:
4. Add twrp.zip to AP tab
10. Copy SuperSU into internal memory from your PC
Click to expand...
Click to collapse
Hey, why this guide doesn't mention that I have to download something. It's definitely NOT definitive! What is twrp.zip? Where do I take it from? What is AP tab? Where exactly do I copy SuperSU? What will happen in the download mode?
Problems in Root J320AZ
My name is Dario Lobos. I am working as a gardener and I am making a little application in my phone. I don't have computer so I did it in Java n-ide. I started with a Samsung core prime but the screen was broken and I did change it and the technicians broke it and gave me an Samsung s320. Android 6 (api23) and after that the java n-ide don't compiles the permits that I am requesting in the manifest so I can't grant permissions to my apk. Parallel of it the phone always show a notice unauthorized actions have been made please restart the phone to undo the unauthorized actions. And the lookout said message root access detected. I wrote Samsung without any positive answer. No technical assistance at all. But the roots checkers says that I have no root in my phone. Now I am trying to do a root. But I don't know if someone have a hidden root access in my phone. A page suggest Framaroot and you suggest kingroot. I don't want to store all my phone in their server to root it. Does any program that don't access to all the data to root the phone?. I am writing you since you have more experience to request you if it is in your possibilities. Also to ask you about prompt root commands. Where I can find info about that. A suggestion to solve my problem. My simple all is here
....github.com/DarioLobos/sistemariego
....github.com/tranleduy2000/javaide/issues/163
....1drv.ms/u/s!Asr3Ewn45KOLtGOqDkoMq20A-hbc?e=24Wwx3
The system don't let me put url since I am new add please http...
Well thank you in advance and any help is wellcome
Regards,
Dario Lobos
Adding more information to what I did to try to find a an answer. I tried to root with Frama root 1.9.3 and the installation only request me access to the camera and after installed the programs showed a banner that said can't root your device.
Today I downloaded from firmware.mobi some zip and img files but I already I couldn't learn how to use them properly.
I am trying to avoid the exploids system because maybe is a hacker in the middle. Always I am trying to root w/o SIM card and with Wi-Fi off. So I think that kingroot and kingoroot are not useful for my.
I am trying to buy an old desktop computer as an alternative.
Well any suggestion is usefull and wellcome.
Before of all of that I did two factory reset in recovery mode.
Then I installed an apk Dev Tools (trinea) and one menu request me developer permit in accesibility setting. The phone started to change the color of the screen and the outside padding start to flashing red. Then was open a setting menu and the language was changed suddenly to Japanese or Korean while the screen was lighting like receiving knoks. I turned of the phone and restarted and hopefully I remembered the position in settings to change the language.
After that I had to use an apk repair system and fix Android and the screen get better but the padding outside still flashing in red ones in a while.
Also where added plenty sha certificates (settings user certificates) like system certificates
Go daddy
VeriSign
Some governments (Turkish, Spain, Japan, Germany, Holland, and more)
The Catholic religion with 6 certificates called
Quo Basis
And much more.
So I did another factory reset recovery mode. And the screen problem disappeared and the certificates that I turned off manually firt too (All) but the root alert in the look out and the security notice didn't disappeared.
Today I wanted to print your forum page and the phone put error. Only put error in your forum page.
Other thing that I had to to just after the unpackage the restored Android is disable the setup and transfer. Because I think that is this apk that were using to access and modify my files and grants permissions.
I installed the TWRP application but said the phone have no root.
Today I opened the developer option in settings and turned to on the OEM option to unlock the boot loader but instead of put a banner saying that all data will be erased put a banner saying that the device protection will be not work and didn't do the reboot or nothing more that put this dialog.
Dario Lobos
great, unlocken/rooten worked here. But after that, the mobile became unusable. All google apps complain no connection is available. I cannot update google play store, cannot update other google apps like youtube, or install any app now.
And perhaps it does not have anything to do with the mentioned process, but before I started the process, I made sure all nessacary file were on the sd card. But now I have finished wiping the data / cache from the recovery and all files on the sd card are gone.
I cannot login to google photos to see if the apps are backupped because every google app complains no internet connection is available.
So yes, rooting/unlocking worked, but that's the only thing that worked here. I now got a useless Samsung J3 2016...
I need assistant trying to root my J320FN, which I mistakenly wipe some backed up recovery file now, I can not get through with the rooting and I can get back to forma phone setting am locked up , samsung phone not coming up again please what can I do ?
GN9166 said:
The definite guide to rooting Samsung Galaxy J3(2016) SM-J320FN & FRP Locked Bootloop
As first I have to say, I had to create a thread in Q&A because of the low rank, but I am sure this can be moved to the J3 section as there are many questions on how to gain root access to this device. This guide can work on the SM-J320F model as well, but it hasn't been tested on other models, so don't try it !
Lets start :
Dont forget to Backup all your data before the process !!!
1. Tick USB Debugging and OEM Unlock in Developer Mode (OEM has to be ticked to unlock the bootloader)
2. Connect to PC with USB Cable and open Odin
3. Power off and reboot into Download Mode (VOL.DOWN+HOME+POWER)
4. Add twrp.zip to AP tab
5. Untick Auto-Reboot and Start
6. Wait to finish
7. When it's finished hold (VOL.DOWN+VOL.UP+HOME+POWER) to Power Off
8. Load into TWRP Mode (VOL.UP+HOME+POWER)
9. In TWRP first go to the Wipe Tab, check Cache and Data and click Wipe
10. Copy SuperSU into internal memory from your PC
11. Go back to TWRP and select Install, select the SuperSU from the internal memory and click install without ticking anything, then reboot
12. Wait for the phone to reboot, it may boot-loop a few times, and it boots slowly but dont interrupt the process !
13. From there on, check the root status by downloading Root Checker from PlayStore
KEEP OEM-UNLOCK ON ALL THE TIME, IF YOU DONT WANNA END UP WITH A BRICKED DEVICE(CUSTOM BINARY WAS BLOCKED BY FRP LOCK)!!!
If that happens, here is an official guide from the Samsung Kies Support Page :
IMPORTANT: You may need your device model name, S/N number, or IMEI number in order to proceed. This information can be found on the label underneath your device battery.
WARNING: This process permanently deletes all personal information from the device. The information will not be recoverable if you proceed with this process.
1. Open Kies 3 and click Tools > Firmware Upgrade and Initialization.
2. Enter your device Model name and click OK.
3. Enter the device S / N number and click OK.
4. Kies 3 will verify that the feature is available for your device. If the feature is available, click OK to continue.
5. The firmware version is displayed along with a note that the information on your device will be permanently deleted during this process. Click OK to continue.
6. Follow the steps to prepare your device for emergency recovery. Mark the checkbox next to I have read all of the above information. Select whether you agree to share this update with Samsung. Connect your device to Kies when you have activated the download mode. When your device is in download mode and connected to Kies 3, the Start upgrade button is available. Click Start upgrade to reinstall the firmware.
7. Touch Create backup to create a copy of selected items before proceeding. Touch Skip backup to proceed without backing up any items.
8. Kies 3 will download and prepare your system to update the firmware. This process can take some time. The time will vary based on your network and computer capabilities.
9. Respond to any security warnings about installing software.
10. The progress screen is shown during the upgrade process. The process will take several minutes to complete. Do not disconnect your device, turn the device off, or turn off your computer during this process.
11. Click OK when the upgrade is finished.
Therefore I provide you all the needed files to do this :
How to root SM-J320FN.rar
Click to expand...
Click to collapse
The link says "the key is invalid"
Hello guys,
I have come many times here to root my phone and I did success, thanks to you.
But now there is a new problem and I did not find any solution, then I will try to explain with my bad english what I did :
At first I tried to flash TWRP (an unofficial one many said it was working) on the phone after unlocking the bootloader, SP flash tool said it was successful.
But it was not, after reboot former recovery was still there, not TWRP (does anyone knows why it did not work ?).
I tried to install Lineage, which bricked my phone. After the debrick, I installed Android 10 GSI, and it worked but impossible to use MTP, Bluetooth or to download with the HTMLViewer (in other words, the system was unusable).
Then I reinstalled the ROM provided by Blackview, and installed Magisk, rooted the phone, also suppressing all the Google stuff it was possible.
And there is the main problem : I think I erased the NVRAM while unbricking the phone and then I have got an overlay of red chinese caracters on the corner of the screen. I tried to replace the original IMEI and MEID successfully with MAUI Meta, but chinese caracters are remaining here.
A screenshot of the ugly writings : https ://ibb.co/bWWp1wr
My phone is a Blackview BV9500 Plus.
Any suggestion about how to remove them ?
Thanks in advance !
I have just tried to replace the BT/Wifi adresses with SN Writer.
The soft said it was a success, but in the system parameters of the phone these adresses were not modified. I wonder why...
I guess these adresses (and/or the serial number, in others words all the parameters of the NVRAM) are the causes of the message. What do you think about that ?
Also, in the official firmware, there are some files for only one choice for the AP and MD databases (what are the correct ones ?).
I think I almost tried everything I am able to do...
Any suggestion or solution ?
Thanks
John Manjiro said:
I have just tried to replace the BT/Wifi adresses with SN Writer.
The soft said it was a success, but in the system parameters of the phone these adresses were not modified. I wonder why...
I guess these adresses (and/or the serial number, in others words all the parameters of the NVRAM) are the causes of the message. What do you think about that ?
Also, in the official firmware, there are some files for only one choice for the AP and MD databases (what are the correct ones ?).
I think I almost tried everything I am able to do...
Any suggestion or solution ?
Thanks
Click to expand...
Click to collapse
Hi John, same issue here, but not same process. Phone won't boot so I've restored which made IMEIs being 111111 and 22222. Used MetaModem (successor of AMUI Meta or whatever you used is called) to restore correct IMEIs. But got those red "TEE" and "Google" followed by Chinese chars. Will keep you updated here if I can find a solution.
@John Manjiro
It seem's Trusted Execution Environment (TEE) for Android is installed on your phone. It's a secure Operating System (OS) what runs in parallel to Android OS. TEE protects phone from malicious apps installed by the user and potential vulnerabilities that may be discovered in Android.
Did you ever find a solution to this?
huafu said:
Hi John, same issue here, but not same process. Phone won't boot so I've restored which made IMEIs being 111111 and 22222. Used MetaModem (successor of AMUI Meta or whatever you used is called) to restore correct IMEIs. But got those red "TEE" and "Google" followed by Chinese chars. Will keep you updated here if I can find a solution.
Click to expand...
Click to collapse
I'm having the same issues with a BV9800 Pro.
cnorman27 said:
I'm having the same issues with a BV9800 Pro.
Click to expand...
Click to collapse
Still same issue, got a long email thread with BlackView team which tried to help even tho they seem to not get well my Enlgish. They keep giving me a version of SNWritter where I had to modify some ini file in some tee subfolder. But the exe couldn't launch and was complaining about MVC100.dll missing. I could fix that by downloading from the web a SNWritter tool with working exe. Now I need to find some special screwdriver so that I can remove the battery from the phone. Doing so will keep the phone appearing as MT65XX Preloader in the devices manager and not for only one second...
Just FYI, I gave up and was using it with this **** red overlay.
Last week I was really bored of this overlay so I've installed AOSP 10 GSI. Tho it doesn't pass safety net, and believe me I've tried many way to make it pass. So I cannot use most of my banking apps + no google pay :-(
I even tried with AOSP 9, 10 and 11, as well as LineageOS 15, 17 and 18... unable to pass safety net even with universal safety net fix, magiskhidepropsconf, ...
Hahaha, looks like I just needed to write the previous post and finally got it wokring on PixelExperience Android 10 rooted and passing SafetyNet!!!!
Quick howto if someone is interested:
with SPFlashTools, restore the original ROM
Activate developer mode + USB debug
on the computer, adb reboot bootloader
Download PixelExperience system image and extract it (on linux with unxz) - I've tried many other ROMs with no success. Also while the device is not an A/B, you must download A/B images else they do not work.
fastboot -w && sleep 1 && fastboot flash system path/to/downloaded/system.img && fastboot reboot
Skip everything you can skip at first boot (you can restore later from an online backup or another android phone)
Download MagiskManager apk
adb push path/to/MagiskManager.apk /sdcard/download/
On the phone go in the file manager in download folder and install MagiskManager
copy the boot-signed.img from stock ROM on the device adb push path/to/boot-signed.img /sdcard/download
Open Magisk Manager, install, uncheck the first checkbox (to disable encryption, I forgot the exact label) but keep "recovery mode" checked, then click on next, then second option (patch boot image) and select the boot-signed.img you uploaded on step 10
download on your computed the patched image using adb pull
adb reboot bootloader
fastboot flash boot path/to/downloaded/patched-boot-magisk.img
You need to reboot in recovery mode, this is important: press power and volume up until you see the Blackview logo (can take up to 40 seconds)
select "reboot" (first option) in the recovery mode
once rebooted, open magisk manager, activate magisk hide and go in plugins.
install MagiskHideProps Config but do not reboot yet
install SafetyNet fix (download from here, it's not in online modules)
click on reboot
It'll reboot in recovery, that is normal and you MUST boot your device into recovery each time you need to boot/reboot it. Once in recovery, as before select reboot
Once it has rebooted, go in magisk and change in the settings so that the default method is not "prompt" but "grant".
from your computer:
adb shell
su
props
Select device fingerprint, then choose from certified, google, pixel 2, android 10
confirm but do not reboot when asked, simply exit
adb reboot recovery
again, select "reboot system"
Once booted, open Magisk Manager, click SafetyNet, it should pass SafetyNet.
Scroll down notification, and choose "continue device setup"
continue as normal the setup of the bv9500 plus!