Ok, here is the deal and I hope someone can help me. I have a cheap DigiLand DL1010Q tablet to play around with. It is stock, but I rooted it with KingRoot. There was a recent OTA wireless update and after it was installed it said that it needed to go into recovery mode to install and reboot. I selected install now and reboot. This is where my problem started and has remained. It loaded into recovery mode and is in an endless boot loop. I've tried rebooting it, recovery with the recovery file and every manual reset possible to no avail. DigiLand support said that I should power down the tablet, and while holding down the Volume Down (-) hit the power button and it will boot into a Chinese recovery mode. I've tried that and it just stays on the DigiLand screen forever. (I left it there for 8 hours.) I can sideload via ADB and the drivers are installed, but it will not let me load anything. It states that the bootloader is closed. I receive the same message via Fastboot. Now here is the interesting thing. Even after selecting the factory reset within the Recovery Mode, everything is still there. I have wiped the cache and partition and user data, but nothing really happens. It is still all there. I see the recovery file, but it will not load. All I see is NO Command.
I do have a sd card that I could flash things on, but it doesn't seem to register the card. It sees the sdcard, but that is the internal drive. How do I get it to look at the sdcard that I put into the slot? Is there a bootloader unlock? Does anyone have the factory image that I can put on my sdcard? HELP!!!!
I am fairly good with computers and have rooted phones and tablets before, but I seem to be hitting my head on a bricked wall - no pun intended. Let me know what programs, files or whatever. At this point I am willing to try anything. I can send it back to China for $50 for them to redo it, but I only paid $69 for it and I'm not going to put more money into this cheap tablet. I would just like to get it to work.
Related
First off id like to say thanks in advance to any replies and also apologize if this has been posted previously (i searched and could not find anything that was helpful) I lurked around these forums when i had my x1 and im hoping you guys can be as helpful for me as you are for everyone else. anyway onto the issue
I used the superboot method to root my ATT US Streak. My intentions were to update to 2.1 following the steps in the "eclair working on my u.s. unlocked streak!" thread (wont let me put a link since its my first post)
after using fastboot to root the phone will boot up and function fine but recovery and fastboot no longer work. i tried flashing Koush's custom recovery and other things that require fastboot and the terminal just says "sending..." nothing happens no errors or anything, the cmd prompt just sits there and i need to remove the battery to reboot the device.
i then downloaded the Rom Manager apk from the market and flashed the clockwork recovery from there (it said i did anyway). when i load the recovery from boot (volume keys + power and its the stock recovery) and chose option 2 to flash modaco custom rom or even the stock dell rom it just goes to a black screen and i once again need to remove the battery to reboot.
the phone itself is still functioning fine when it boots up and everything works the way it should other than the home, menu, and back button lights flash in random orders, thats just annoying though. again any help is appreciated
so what should i try next?
EDIT: woke up this morning and now the device will not turn on. i tried starting to fastboot and recovery but still nothing. plug it into my pc and i get the "found new hardware wizard" for a Qualcomm CDMA Technologies MSM.
first real brick? ha that would be my luck
EDIT 2: a kid just ran through my work, grabbed my phone and threw it on the ground. it screwed up the 30 pin connector on the phone and the charger. im going to hurt somebody. phone is booting again though... put sd card back in and still boots fine
SOLVED: Dont know the technical reasons behind it but i had to reinstall the drivers and switch usb ports for every fastboot and recovery procedure
removed SD card and its booting up normally. any thoughts?
I attempted to root a denver tac-70061 tablet in order to be able to switch the mounting of the internal and the external sdcards. I have only rooted once before; a denver tac-70031 tablet which was extremely easy to root by simply installing and running the superuser app. Unfortunately, it seemed that it was not as simple on the 70061.
As I am a novice, I followed the instructions blindly and read them through a number of times before attempting.
I followed a set of instructions which described downloading a zip file which contained adb for windows and some img and zip files to transfer to the sdcard.
I am using ubuntu, so I assumed that the adb which was installed along with android sdk would suffice.
I copied the required files to the root of the tablet's internal sd card and installed recovery via adb.
I unplugged the tablet and rebooted in recovery holding down volume-up while powering on.
When in recovery, the instructions told me to install superuser 3.1.3.zip from the sdcard but this file was not present.
When selecting 'reboot', the tablet kept rebooting to recovery and now seems to be stuck in a loop.
I hope that someone can help.
Factory Default reset?
How do you even get into the recovery menu. W/o I try, I get to the screen with the stupid robot laying down, and a ! inside a triangle showing. What buttons do you press to open recovery menu? On that page, no lists of stuff appear, and I want to reset the android tablet I used, also a TAC-70061, b/c it just keeps loading on the 3rd boot screen, and never gets passed it. Lame Denver product is not worth 2 cents. Apart from how annoyed I am, can you explain to me how to get into the factory reset and reset it/fix it?
Hello,
I own an Android tablet KO PARA1 FULL and experiencing a strange problem. This is a chinese atm7029 quadcore tablet (16gb, 1gb ram, without bluetooth, only wifi, bu supports 3g dongle), running android 4.1.1 nad 3.4.0+ kernel, which came prerooted. After some time I've decided to install backup programs on in to make a full backup of the device for the case something would go wrong, and after some trying I descovered, that there is something like recovery for that purposes which seemed a good solution for me. I decided to install CWM, which I managed to install without problems and made some backups on my device. Everything was fine, I did some factory resets through the time, some restoring processes from my previously backup states of the device, was always able to activate CWM recovery menu through Reboot to recovery or through combination of Volume down a Power button...
Until last saturday. I was normaly surfing the internet, reading mails and afterwords I powered my tablet off (it is draining battery in sleep mode, but its another story..). After a while wanted again to write a mail, so I powered it on. In that momet seemed the screen too dirty for me and I tried to cleen it little bit throug the bootup process. Unfortunately I obvious confused the system with it and after boot it was not responding properly. I did not wait enough and after a while powered it off with power key pressed for a long time, to make a new boot.
But when I powered it on again, it stayed stuck in boot logo and did not boot at all. I've tried a copple of times to boot it again with no cuccess, stayed stuck in boot logo for more then 10 min...
Afterwards I decided to make it boot up with the help of computer. I downloaded adb and drivers and somehow managed to make it boot up. I thing I was too excited to see it boot up again, that during boot up process I desconected my device from computer...
My worries were reliesed and I thought it would be a good idea to make a restore from backup to prevent some strange behaviour, so wanted to boot into recovery, but nothing had happened. After some repeated clicks on Boot into recovery button, as well as app called rebooter with nothing happening, I decided to try it out through button combination. It has not worked as well Next try was to reset to factory settings. But when I go through the menu, I can click on reset to factory settings button, seeing warning that I will lost ma data, then I can push the button to make it happen, but nothing is happening. I see only the screen with the button, can touch it 100 times and the tablet stays on, fully funcional. making no factory reset as it done before.
I did a lot of reading and searching, but have not find answer for my problem. I flashed recovery images from my backups (using flashify, flash gordon, adb shell, terminal emulator), from all previously functional states of the device. I refleshed the CWM recovery downloaded from the internet for my chipset, which previously did the job just perfect, with no success...
I am still not able to reach recovery menu. For me it seems like the bootloader would be locked, but I did not find the answer how to unlock it without to be able to start in some recovery state to use fastboot command to unlock it.
Otherwise, my device is functional, still rooted, i can use it without any other problems. But not be able to do recovery from my backups, even do a factory reset.
How can I restore my access to recovery mode? Is it somehow possible?
Hopfully it is not too much information (tryied to follow the intructions and wrote everything I thought would be important to know about) and you will not be bothered to read all my story and pull me out of my darkness with helpfull suggestion.
Thanks a lot in advance
Steve
i own a zte quest (n817) which is very sluggish. i had it rooted and decided to uninstall a good amount of apps to help it run faster a few months back. it worked fine for the uses i needed it for (calls, text, few apps, wifi etc.) but i wanted to do a factory reset. after doing so from the settings menu, my phone rebooted and went through the setup but the home screen is blank (screenshots below). im thinking the phone didnt reset all the way and it also might still be rooted. i wanted to know what i could do to try and recover the phone in its original state.
things ive tried: im able to put the phone in stock recovery, tried an update.zip from a similar zte phone but wouldnt work. tried a factory reset and cleared cache from the recovery. when the phone is at the home screen, i can plug the phone up to the pc and see the contents of the phone. i can also put the phone in download mode. while in download mode, tried to run some adb commands so i could maybe use dd to flash the .img files but either the operation not permitted or it just did nothing.
im trying to find the update.zip for this phone because i think that would be the simplest option. other than that, any help is much appreciated
Since FuHu has removed the updates for the nabi2 ant otheres probably,i decided to give it a whir myself. I installed twrp 2.2.,went through some setting and in doping so somehow i have deleted the OD on the tablet. I searched and found the stock rom for the nabi2-nv7, put it on a sd card, put the sd card in, and wouldnt ya know it the version of twrp i had wouldnt read the card. I downloaded vers 2.8 and installed it, everything seeemed to be ok untill i went to slid the button to install, it wouldnt move. I rebooted, then went back into twrp once more with hopes, no deal, slider stil wouldnt work. After doing more reading I downloaded twrp 2.6 and that one was supposed to work, installed it, nowi have next to nothing. Without being plugged in to power, i can get to this screen,but anything i select will no work. Now if i plug the tablet into power, it automaticall goes into screen #2 still with no being ablee to get into anything.
Screen#1
boot normally
fastboot protocol
recovery kernal
forced recovery
Screen #2
bootloader
continue
reboot-bootloader
reboot
power off
It just keep fliping back and forth betwen thos 2 screens,it shows connected on my laptop,but try to do anything ( adb devices ) and it says no device connected..
Im thinking that the twrp's are working against one another and has meloced out in some way or another, is there any way i can wipe it all clean and start from scratch?
Any and all help is appreciated. also read wher xda has a toolkit for the nabi2, searched but not really sure what im looking for.
Thank you
Rascle