This is the problem I am having with my Samsung Galaxy Note 3 (SM-N900P). This problem just popped up out of the blue on a stock ROM a few days ago and nothing I have tried has gotten close to fixing the issue
Description:
a) The boot sequence repeats in a loop with no more sound. The phone would reboot at the Sprint splash screen
What I've done so far:
a) Pulled the battery and depleted the capacitors
b) Installed TWRP and did a complete wipe
c) Tried installing a custom ROM to see if the issue persisted. ROMs failed to install as /system was being sketchy (at times it was reporting 0MB for partition and then an actual value after repair). When I managed to get a ROM to install still stuck in the boot loop
d) Used Odin to do a full restore to a stock NC5 ROM. The phone got up to initial configuration page and then rebooted, now only gets to the Samsung splash screen before rebooting
Items that I can get into:
Recovery mode
Download mode
I have a 30 second video of it rebooting but cannot post it currently due to the forum rules
Question:
Is this issue fixable or is it a sign of internal memory failure?
Try an older version of TWRP, i.e. 2.8.5.0
Or, try a different recovery.
I'm not sure that it will work, but it's worth a try.
Good luck!
Are you doing it this way?
http://forum.xda-developers.com/showthread.php?t=3069667
rbeavers said:
Are you doing it this way?
http://forum.xda-developers.com/showthread.php?t=3069667
Click to expand...
Click to collapse
I didn't notice that but I just installed TWRP 2.8.0.0 through Odin (like a few minutes ago). Phone actually managed to get to the stock recovery image config screen and was working as long as the cable was still attached to the computer.
As soon as I removed the cable it went straight back to the boot loop
SubRyan said:
I didn't notice that but I just installed TWRP 2.8.0.0 through Odin (like a few minutes ago). Phone actually managed to get to the stock recovery image config screen and was working as long as the cable was still attached to the computer.
As soon as I removed the cable it went straight back to the boot loop
Click to expand...
Click to collapse
Here is what you need to do. First pull battery, reinstall. If you can boot into twrp recovery, fine wipe everything i.e. caches, system, data, etc. If you are on a stock recovery do a factory reset. Pull battery, reinstall and boot into download mode.
NOW let's go to work. First use odin to flash stock NC5 tar. Chances are it will bootloop, STOP !!!! don't panic. Just reflash with odin again. The second time it should take. Remember that your device is setting up for first time use. This will take 3-5 minutes, sitting at the Samsung logo. Since didn't list the most important thing which is what OS you where on where the device Borked, or what you where doing with the device when it Borked. I'm going to assume it was on 4.4.4 and you tried to downgrade to 4.4.2 NC5. In which case a bootloop on the first bootup after a downgrade is normal, you have to flash twice to reset the bootloader. For more info click on rom flashing basics in my signature. Enjoy !!!
Problem solved. I started getting suspicious when the phone would boot up with the charging cable attached to the computer today
The issue was an aftermarket Mugen Power battery that developed a fault. Put the stock battery back in and problem resolved
Thanks for the help guys
Related
EDIT: As I've now gotten Odin to flash again, and my device still won't boot, I'm really starting to think Andromeda's recovery has wiped something vital that isn't restored with a "regular" stock ROM image. PIT? EFS? Partitioning? Something like that? Odin successfully flashes the whole image tar (which I've previously used successfully), and the boot splash now correctly changes to the default Samsung one without triangle, but still the phone won't boot (as described in msg #3). So I'm now wondering if there's any way to a more aggressive restore (whence the topic title change)? Or am I barking up the wrong tree here?
----------
Hi
Okay, so I was testing out different kernels with Paranoid Android. I had the Dorimanx kernel installed at first, but had some volume issues, so I shifted to the Dream kernel, wouldn't boot. Then then the Andromeda kernel, and it still wouldn't boot, so I thought I might try doing a factory wipe in Andromeda's recovery. It then froze, and after about 20 minutes I gave up waiting for it and reset the device.
I then tried using the recovery to reinstall the Dorimanx kernel that worked, but it would fail, too. Just hang. After some attempts, also at just mounting the storage via USB, everything would fail, a couple of times with a message about emmc not mounting IIRC.
I then got a response on PA's forum about which kernel was suggested, and the answer was the stock kernel, so I thought I'd just use Odin to flash a CF kernel.
I think I had to do two attempts, or maybe just one, but it succeeded in installing the kernel, and the device rebooted. Except it didn't really. I can't get a "regular" boot screen (the one with the triangle), and so I can't get into recovery. Also, when the charger is plugged in, instead of showing first the grey battery icon with the spinner in it (which I seem to remember would spin before) and the going to the battery with green, it just show the grey icon with a spinner that doesn't spin. It never goes to the green battery screen.
I could (and can) still get to download mode, so I thought I'd do a back to stock routine. I downloaded a full stock ROM and tried to flash it with Odin. It would then freeze at the setup connection step. I tried a different image, same result. I tried reflashing the CF kernel (which worked just minutes before with Odin), again with the same result. I tried different USB ports and cables (even though I just used Odin successfully before), rebooting, unplugging at the frozen step and plugging back in, but to no avail. Odin won't flash any .tar.md5 anymore AFAICT. At least not with the regular no-frills one-click approach.
I'm fearing a hardbrick here. Except I still have access to download mode, and Odin sees the device. Could the recovery in Andromeda have destroyed the partition table perhaps? Or overwritten something it wasn't supposed to?
Is there a different approach to recovery that I could try out? Or does any one of you have any tips I might try out? Anything would be most welcome and appreciated
Thank you,
Daniel
PS: Oh, I just tried starting it up after it's been without battery and unplugged overnight and all day. I tried starting it into recovery mode, and now I have a different screen altogether: It says, "Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again. Well, that sounds tempting! Except - I've never used Kies on this device in the first place, and Kies does not having any clue what I've been doing with this thing... Would it be safe to try out? I'm hesitant...
Daniel Smedegaard Buus said:
Hi
Okay, so I was testing out different kernels with Paranoid Android. I had the Dorimanx kernel installed at first, but had some volume issues, so I shifted to the Dream kernel, wouldn't boot. Then then the Andromeda kernel, and it still wouldn't boot, so I thought I might try doing a factory wipe in Andromeda's recovery. It then froze, and after about 20 minutes I gave up waiting for it and reset the device.
I then tried using the recovery to reinstall the Dorimanx kernel that worked, but it would fail, too. Just hang. After some attempts, also at just mounting the storage via USB, everything would fail, a couple of times with a message about emmc not mounting IIRC.
I then got a response on PA's forum about which kernel was suggested, and the answer was the stock kernel, so I thought I'd just use Odin to flash a CF kernel.
I think I had to do two attempts, or maybe just one, but it succeeded in installing the kernel, and the device rebooted. Except it didn't really. I can't get a "regular" boot screen (the one with the triangle), and so I can't get into recovery. Also, when the charger is plugged in, instead of showing first the grey battery icon with the spinner in it (which I seem to remember would spin before) and the going to the battery with green, it just show the grey icon with a spinner that doesn't spin. It never goes to the green battery screen.
I could (and can) still get to download mode, so I thought I'd do a back to stock routine. I downloaded a full stock ROM and tried to flash it with Odin. It would then freeze at the setup connection step. I tried a different image, same result. I tried reflashing the CF kernel (which worked just minutes before with Odin), again with the same result. I tried different USB ports and cables (even though I just used Odin successfully before), rebooting, unplugging at the frozen step and plugging back in, but to no avail. Odin won't flash any .tar.md5 anymore AFAICT. At least not with the regular no-frills one-click approach.
I'm fearing a hardbrick here. Except I still have access to download mode, and Odin sees the device. Could the recovery in Andromeda have destroyed the partition table perhaps? Or overwritten something it wasn't supposed to?
Is there a different approach to recovery that I could try out? Or does any one of you have any tips I might try out? Anything would be most welcome and appreciated
Thank you,
Daniel
PS: Oh, I just tried starting it up after it's been without battery and unplugged overnight and all day. I tried starting it into recovery mode, and now I have a different screen altogether: It says, "Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again. Well, that sounds tempting! Except - I've never used Kies on this device in the first place, and Kies does not having any clue what I've been doing with this thing... Would it be safe to try out? I'm hesitant...
Click to expand...
Click to collapse
the reason for Dream and Andromeda not booting ur phone is that, if ur paranoid rom version was latest, then it comes with the new JB mali drivers for which only Dori v7.4 and siyah v5.0 are compatible
since u have already messed up too much with ur phone, u can try the 'KIES' option as the last resort to restore it back, since odin flash is not wrk'ng for u
Okay, so I tried installing Kies and connecting it. A variety of connection attempts, but it just won't connect to the device.
But, I'm making some progress! I've found that when I can get the phone to boot into the "Firmware upgrade encountered an issue." screen, I can get Odin to flash the stock Gingerbread image (still won't in download mode). And I then get a reboot with the regular Samsung boot splash (no yellow triangle) - except it never gets past it. After about a minute, it'll go black and then boot back up to the same splash screen and the same problem.
This is the exact same image I've used previously to revert the device to stock. So I was kinda hoping to see a normal clean. But unfortunately no donut. It reminds me of a computer I once bricked by screwing with its BIOS - it never got beyond POST and so I couldn't reflash it.
Is there something like a BIOS in this thing that could've gotten damaged in some way? And if so, is there any way to use Odin or another tool to fix that?
Cheers,
Daniel
Tried flashing a couple of matching CF kernels. I now get the green battery after the grey one, but still no boot.
All turned out the be the Shun Andromeda kernel re-introducing the hard brick bug. If you have the same issue, see my reply here for links to where you can get the custom PIT trick up and running.
So my friend's phone died during a software update which completely messed up his phone. I thought it would be a simple fix, no problem, but there is hardly any valid information out there that can help me (due to a lot of dead links). Here's the issue:
The phone (SPH-M950 btw) loads the initial "Samsung" image on the screen. Then it goes away and starts to boot up with a blank screen. My computer recognizes the device until a couple seconds late the phone restarts itself and continues this boot loop. I cant boot into the stock Android Recovery but I can boot into Download Mode. I've tried for hours to flash all kinds of ROMS with Oden but, despite the fact that Oden says everything worked, it still continues the boot loop.
If possible I would like to get the OS to work again without losing any data. If not then I would at least like to get the phone to return to it's OOB state so it's at least functional.
Help please?
Answer
SomeguynamedBentley said:
So my friend's phone died during a software update which completely messed up his phone. I thought it would be a simple fix, no problem, but there is hardly any valid information out there that can help me (due to a lot of dead links). Here's the issue:
The phone (SPH-M950 btw) loads the initial "Samsung" image on the screen. Then it goes away and starts to boot up with a blank screen. My computer recognizes the device until a couple seconds late the phone restarts itself and continues this boot loop. I cant boot into the stock Android Recovery but I can boot into Download Mode. I've tried for hours to flash all kinds of ROMS with Oden but, despite the fact that Oden says everything worked, it still continues the boot loop.
If possible I would like to get the OS to work again without losing any data. If not then I would at least like to get the phone to return to it's OOB state so it's at least functional.
Help please?
Click to expand...
Click to collapse
Did you try to access the recovery mode after you flashed anything?
Try it and check whether it works. Then try to format /system /data and /cache (internal data will be lost) and then reflash stock rom via Odin.
Then try again.
the_pirate_predator said:
Did you try to access the recovery mode after you flashed anything?
Try it and check whether it works. Then try to format /system /data and /cache (internal data will be lost) and then reflash stock rom via Odin.
Then try again.
Click to expand...
Click to collapse
I forgot to talk about accessing recovery mode. All that happens an Android logo pops up and starts to look like it's loading the recovery os but then the phone just reboots again and continues to do the boot loop. Nothing changed no matter what custom recovery I flashed.
I would have no problem if I could just get into the recovery menu but that's my biggest obstacle.
Hello,
I have a S3 which is stuck in a bootloop at the samsung logo.
when i turn it on it shows the logo for some seconds then the screen goes black and the logo re-appears.
i can not boot into recovery mode, but download mode is working without a problem every time.
i tried flashing stock firmwares with odin and also tried kies emergency firmware recovery. the flashing always went without any problem, but it had effect. whatever i try, i am never able to boot into recovery and still stuck in the bootloop.
in some tries after flashing the screen just shows the samsung logo forever, but after rebooting it once it then is stuck in a bootloop again (shows the logo - screen goes black - shows the logo...)
i also tried flashing TWRP and CWM via odin, but again i can never boot into recovery mode.
what should i try next?
thx alot for any helpful comment
Varjo said:
Hello,
I have a S3 which is stuck in a bootloop at the samsung logo.
when i turn it on it shows the logo for some seconds then the screen goes black and the logo re-appears.
i can not boot into recovery mode, but download mode is working without a problem every time.
i tried flashing stock firmwares with odin and also tried kies emergency firmware recovery. the flashing always went without any problem, but it had effect. whatever i try, i am never able to boot into recovery and still stuck in the bootloop.
in some tries after flashing the screen just shows the samsung logo forever, but after rebooting it once it then is stuck in a bootloop again (shows the logo - screen goes black - shows the logo...)
i also tried flashing TWRP and CWM via odin, but again i can never boot into recovery mode.
what should i try next?
thx alot for any helpful comment
Click to expand...
Click to collapse
You can Try this:
1.) Pull out battery
2.) Put it in again
3.) Press Vol up + home + power
4.) When the Samsung Logo appears let it off
I think you press the Buttons too long.
I had the same problem!
S1ay3r666 said:
I think you press the Buttons too long.
Click to expand...
Click to collapse
i really tried everything, it's not working. btw with i am stuck at the very first image, where it says "samsung Galaxy sII GT-I9300".
i dont think it's just the way i press the buttons because i can reach it on my s1 and s2 without a problem, it's just not working on this device.
could some setting like "nand erase all" in odin help? in other threads there is sometimes mentioned that the internal file system might be screwed up and in those cases a simple odin reflash does not help anymore...
Nand erase will usually hard brick it. Try the rescue firmware from general forum, sticky thread. Follow the guide exactly as it includes a pit file.
Sent from my GT-I9300 using Tapatalk
boomboomer said:
Try the rescue firmware from general forum, sticky thread. Follow the guide exactly as it includes a pit file.
Click to expand...
Click to collapse
thx, but i already did that (multiple times) and flashing via odin always succeeds. then the phone reboots and is stuck at the first samsung galaxy s.. screen. twice i managed somehow to get into recovery (after flashing cwm6) but it then randomly rebooted.
and i dont think that the power button is stuck because when i am in download mode it is perfectly fine it never reboots itself unexpectedly.
Had a similar issue on my tab2 p3100. It all happened when I tried flashing a custom recovery from rom manager.
A bad flash of anything related to recovery or bootloader could be a probable cause.
I remember a knowledge share on one of the threads describing this issue and as mentioned on it all I had to do is this:
1) switch off the device and plug in the charger. This would light up the display showing you the charging status. The status has to show if at least your bootloader part of the phone is fine.
2) plug out the charger and immediately press the three buttons (home + vol up + power) get into recovery mode. This step has to work and help you get to recovery mode.
***Note : the interval within which this step has to be performed is too short since the display would turn off immediately as soon as you plug out the charger. A bit tricky too so you have to be fast. If this misses getting you into recovery, pull out the battery and put it back again. Repeat step1 and 2 again.
3) upon successfully getting into recovery, perform wipe data, cache and select reboot phone from option available on recovery again.
Allow the device to boot. This could take a while since you have performed a data wipe and may prompt for first time set up.
I was able to restore functionality on my tab after these steps and like ppl learn from their mistakes, I then learnt that recoveries and bootloaders are things that needs to be done with a pc only.
Worth a try if you have tried other alternatives and found no go. may help. Who knows..
all the best.
thats also not working. i tried to get into recovery since two days now...
i also tried the steps from this thread: http://forum.xda-developers.com/galaxy-s3/help/solved-pit-bricked-dead-problem-gt-t2535367
but again, after i flash the cf-root (successfully) the phone does neither boot into recovery by itself nor can i do it by hand...
its crazy... in download mode i can see the model number (GT-I9300) and i thought as long as the model number is there and i can enter download mode there should be a way to recover the device.
but i cannot think of anything to try that i have not done yet
If the rescue firmware didn't help then it looks like the emmc chip is damaged.
Sent from my GT-I9300 using Tapatalk
boomboomer said:
If the rescue firmware didn't help then it looks like the emmc chip is damaged.
Click to expand...
Click to collapse
is there a way to make certain of this? how can i tell if it is really a hardware damage and not just a software brick?
i just dont want to let the phone go, it looks still so shiny
is there anything else that could cause the phone not booting into recovery mode after flashing custom recoveries?
Varjo said:
is there a way to make certain of this? how can i tell if it is really a hardware damage and not just a software brick?
i just dont want to let the phone go, it looks still so shiny
is there anything else that could cause the phone not booting into recovery mode after flashing custom recoveries?
Click to expand...
Click to collapse
http://forum.xda-developers.com/gala...-help-t2737707
Same here, still didn't found how to fix it.. I guess our motherboard just died..
Howewer I have a solution that "almost" worked for me.
Get a stock firmware in odin and turn on Nand erase and T-flash
When it's done phone reboots and you'll see just "Downloading..." mode when you turn it on.
Then got to Kies and Select firmware recovery...
Enter s/n and model name and wait for the flash to complete.
With it , I got past boot logo and actually booted into android but the phone crashed because I guess I have a memory issue..
Well , gl. If you don't find anything else helpful , try going with this method..
My phone is a verzon note 2 on deodox 4.3 with twrp recovery. The phone only boots to teamwin logo and flickers on and off. my computer will not recognize my phone either at this point.This is what happened. Ive been having some 4g lte loss and unstable wifi issues to i decided to do a factoty reset. when i rebooted into recovery i was stuck at the twrp logo and it would constantly bootloop the twrp logo.. I restarted my phone and did a factory reset from under the general setting. At that point it rebooted int the twrp but continued to just stay at the logo and would not go into recovery. I pulled the battery and restarted the phone but from that point on it would only boot into the twrp logo and stay there. I can get into download mode but my pc (win7) no longer recognizes the phone so i cant attempt to fix this in odin. Im not sure what to do to get this phone to work properly at this point.
yoda254 said:
My phone is a verzon note 2 on deodox 4.3 with twrp recovery. The phone only boots to teamwin logo and flickers on and off. my computer will not recognize my phone either at this point.This is what happened. Ive been having some 4g lte loss and unstable wifi issues to i decided to do a factoty reset. when i rebooted into recovery i was stuck at the twrp logo and it would constantly bootloop the twrp logo.. I restarted my phone and did a factory reset from under the general setting. At that point it rebooted int the twrp but continued to just stay at the logo and would not go into recovery. I pulled the battery and restarted the phone but from that point on it would only boot into the twrp logo and stay there. I can get into download mode but my pc (win7) no longer recognizes the phone so i cant attempt to fix this in odin. Im not sure what to do to get this phone to work properly at this point.
Click to expand...
Click to collapse
My guess is that when you rooted with CASUAL, it changed the Samsung device driver on your computer and you need to reinstall the Samsung driver to get the computer to recognize the phone again in download mode.
Underneath step 7 of section 1b on Droidstyle's restore guide, he discusses issue with CASUAL replacing the Samsung driver... and he gives a link to Jeremy Loper's fix... "If odin no longer recognizes your device, most likely Casual killed the driver for odin!! follow this tutorial for restoring the driver: http://www.youtube.com/watch?v=zzghcV8HVVk"
Once the computer recognizes the phone again, you should be able to use ODIN to restore back to 4.1.2 so you can root/unlock again with CASUAL. After you get the phone restored with Odin, I would recommend booting into Stock Recovery and wiping cache/doing factory reset before running Casual again... this would enure you are starting over with a totally clean slate.
If the above doesn't work, then here's a thread where I tried to help someone else who couldn't get their computer to recognize the phone.... maybe some of those ideas will help - http://forum.xda-developers.com/showthread.php?p=55833998
Good luck!!
1 step forward two steps back. I got my pc /odin to recognizes my note 2(changed usb cords). Then tried to odin back to stock 4.1.2. At first odin kept saying (odin not responding) and would ask to close the program,after several attemps i final got it to flash the 4.1.2 file. When i flashed the file and was at the point where it reboots, it would not get past the samsung note 2 logo and continued to flicker and not boot up even when i tried to put it into download mode like it said to in this thread. http://forum.xda-developers.com/showthread.php?t=2024207. When i tried to reflash the file it failed. when i attempted again it just hangs at setupconnection. Tried again and it failed. Btw thanks for the help mattnmag.
Got it working! i simply forgot to place the sch-i605 pit. into the pit section of odin when i flashed the 4.1.2 rom.
Similar problems
I was running AllianceROM 26. My phone had been spontaneously rebooting for a bit recently. Today, it started to spontaneously reboot again, but this time, it never got past the Galaxy Note 2 screen. After pulling the battery, I tried to boot into TWRP. It just hangs on the twrp boot screen for a few minutes but never goes into twrp.
I figured I would try taking it back to stock. So, I used ODIN to try and put 4.1.2 on it and a new PIT file. That appeared to work fine. I got no errors in ODIN. However, I still cannot get this thing to get past these boot screens, either the Galaxy Note 2 one or TWRP when I try that there. I have tried this twice now, once with re-partition checked and another time with re-partition unchecked (saw conflicting instructions on that so I figured I would try it both ways). I still am not getting past the boot screen.
Any help or ideas are appreciated as right now, my phone appears to be bricked and I am out of ideas.
so what was the solution to the teamwin flashing on and off after a factory reset? this is certainly not a solution, having to reflash the phone...
Hi there,
I am new to android phone and I had an old Grand Quattro GT-I82552 to play with.
I followed the guide at xda http://forum.xda-developers.com/showthread.php?t=2494471, downloaded
- ODIN v3.07
- CWM Recovery v6.0.4.5
- Stock Recovery GT-I8552
I followed the steps and flash CWM Recovery v6.0.4.5, but on next boot it won't go to CWM recovery mode (I did removed battery first). I tried many times with other CWM from different sources and now my phone won't boot, it just show up the Samsung Logo with yellow triangles, then shutdown. It doesn't look like a loop boot, as it shutdown entirely. I can't charge the phone either.
I can still go in the usb downloading mode so I flashed the stock recovery, no luck, phone still can't boot.
Any advice is appreciated. Thank you.
EDIT: I found out that I was too careless to noticed that Volume UP is required for boot into CWM, instead as Volume DOWN. So I can boot into CWM now, however I supposed I can withhold my SuperSU install, and just boot into my stock Samsung appearance by normal shutdown and startup of my phone? I can't, everytime I tried to power on, it get's me to empty battery screen then shut off. I can't seem to charge the phone as well.
Have you tried charging the phone for a few hours while in recovery mode, and then turn the device on?
marco199609 said:
Have you tried charging the phone for a few hours while in recovery mode, and then turn the device on?
Click to expand...
Click to collapse
Thank you for your suggestion I will try that. Actually I tried to splice a USB wires and connect red/black to +/- contact for the battery and charge it for few hours, it doesn't seem to get hot, and certainly the phone still can't switch on with the battery.
Initially I thought maybe I messed up the firmware (really I only flash cwm) hence the phone's battery charge controller is not working that's why I tried external charging, but I am not too sure now.
My only hope is to get a way to verify I have enough battery power so I can flash the stock recovery in "downloading mode". I dare not flash recovery without full battery, though the download mode can be accessed while I plugin into PC's usb port.
tancb said:
Hi there,
I am new to android phone and I had an old Grand Quattro GT-I82552 to play with.
I followed the guide at xda http://forum.xda-developers.com/showthread.php?t=2494471, downloaded
- ODIN v3.07
- CWM Recovery v6.0.4.5
- Stock Recovery GT-I8552
I followed the steps and flash CWM Recovery v6.0.4.5, but on next boot it won't go to CWM recovery mode (I did removed battery first). I tried many times with other CWM from different sources and now my phone won't boot, it just show up the Samsung Logo with yellow triangles, then shutdown. It doesn't look like a loop boot, as it shutdown entirely. I can't charge the phone either.
I can still go in the usb downloading mode so I flashed the stock recovery, no luck, phone still can't boot.
Any advice is appreciated. Thank you.
EDIT: I found out that I was too careless to noticed that Volume UP is required for boot into CWM, instead as Volume DOWN. So I can boot into CWM now, however I supposed I can withhold my SuperSU install, and just boot into my stock Samsung appearance by normal shutdown and startup of my phone? I can't, everytime I tried to power on, it get's me to empty battery screen then shut off. I can't seem to charge the phone as well.
Click to expand...
Click to collapse
Don't worry your phone will charge while in recovery around 2% in 6-7 minutes. After that you can flash stock os via Odin. Next time you try to flash recovery don't check auto reboot in Odin when flashing of tar file will complete remove battery and boot to recovery. Then flash supersu
redhead77 said:
Don't worry your phone will charge while in recovery around 2% in 6-7 minutes. After that you can flash stock os via Odin. Next time you try to flash recovery don't check auto reboot in Odin when flashing of tar file will complete remove battery and boot to recovery. Then flash supersu
Click to expand...
Click to collapse
Thanks for your advice. I took both of your advice and had my phone flashed with Stock ROM and now it returned to normal with fully charged battery sign shown. My battery appears to be fine with and fully charged, the battery current probably can't be detected with my broken phone back then.
With StockROM in and fully battery, I redo the custom flashing and I am now on custom ROM! Though have some problem with the ROM (battery report not correct, no front camera..) but I am happy now the phone is back to work now.
Thank you very much.