Related
Following up a guide to install CWM, I bricked my Huawei G610. It is on bootloop now. No Fastboot access too.
Any hardware key combination to re-install stock firmware including Recovery?
I recall few phones had a process to put ROM on SDcard and with special hardware key combinations, it used to re-flash fron SDcard.
Help will be appreciated.
sadnblueish said:
Following up a guide to install CWM, I bricked my Huawei G610. It is on bootloop now. No Fastboot access too.
Any hardware key combination to re-install stock firmware including Recovery?
I recall few phones had a process to put ROM on SDcard and with special hardware key combinations, it used to re-flash fron SDcard.
Help will be appreciated.
Click to expand...
Click to collapse
Check on need Rom G610 U20, Download ROM, unzip, theres a doc. file guide attached how to install..
Joe_Live said:
Check on need Rom G610 U20, Download ROM, unzip, theres a doc. file guide attached how to install..
Click to expand...
Click to collapse
Already followed that but it doesn't go to upgrade mode. Tried 2 SDcards so shouldn't be a bad SDcard issue.
If I plug the computer with Laptop, it detects phone but phone keeps rebooting hence I can't control the phone through SP Flash or ADB or other tools. Even in Fastboot mode, it restarts.
Same issue here
Any Luck with your device?
stuck in Bootloop
I faced the same problem after trying to flash TWRP recovery img. I used MobileUncle Tools to flash it. It asked Reboot in recovery, I pressed OK. and it never ran into recovery mode. Its stuck in bootloop now. Any way out? Have tried through ADB but fastboot doesn't work...
My problem was solved by Huawei. I claimed my warranty!
To solve this issue use sp flash tool without batry
Sent from my HUAWEI G610-U20 using Tapatalk
Help
thesumanthapa said:
I faced the same problem after trying to flash TWRP recovery img. I used MobileUncle Tools to flash it. It asked Reboot in recovery, I pressed OK. and it never ran into recovery mode. Its stuck in bootloop now. Any way out? Have tried through ADB but fastboot doesn't work...
Click to expand...
Click to collapse
I have encountered the same problem Is there any solution
sadnblueish said:
Already followed that but it doesn't go to upgrade mode. Tried 2 SDcards so shouldn't be a bad SDcard issue.
If I plug the computer with Laptop, it detects phone but phone keeps rebooting hence I can't control the phone through SP Flash or ADB or other tools. Even in Fastboot mode, it restarts.
Click to expand...
Click to collapse
hi I got the same problem today. can you tell me how did you resolve your issue long time ago.
thanks
Abbas
mobdanish said:
hi I got the same problem today. can you tell me how did you resolve your issue long time ago.
thanks
Abbas
Click to expand...
Click to collapse
Over 2 years now and I probably have changed 4 phones. Don't remember. But to help you. you may try this:
http://forum.gsmhosting.com/vbb/f810/huawei-g610-u20-bootloop-problem-1776731/
my phone isn't working, every time i open my phone it says "unfortunately, dev stopped working". and there are too many viruses that keeps on downloading. any idea how to fix this? huawei-g610-U20
I have a VIBEZ K910 with locked bootloader after upgrading to version 4.4.2. Now it's bricked. Cannot enter test mode with the combination Volumn - and Power button. I think the droidboot.img is damaged. Cannot enter recovery either. Anybody can help me unbrick the phone? Pls:crying:
Sorry to hear about your bricked phone. I can't help specifically as I don't have a Lenovo, but having a search around XDA there seems to have been some success reported in the following thread:
http://forum.xda-developers.com/showthread.php?t=2597590
See this post - http://forum.xda-developers.com/showpost.php?p=52013378&postcount=412
Another post in that thread suggests:
Turn off the phone --> Run minimal ABD and fastboot as admin--> just write the command for recovery install (don't hit enter yet)--> press volume + and volume - button and connect the phone to pc via usb--> now hit enter and voila. Your phone will boot in recovery.
Click to expand...
Click to collapse
Good luck!
anyone?
f4780y said:
Sorry to hear about your bricked phone. I can't help specifically as I don't have a Lenovo, but having a search around XDA there seems to have been some success reported in the following thread:
http://forum.xda-developers.com/showthread.php?t=2597590
See this post - http://forum.xda-developers.com/showpost.php?p=52013378&postcount=412
Another post in that thread suggests:
Good luck!
Click to expand...
Click to collapse
i tried this aldready, but my phone is locked bootloder so that method is no help. Thank you for your support anyway.
hientran41 said:
i tried this aldready, but my phone is locked bootloder so that method is no help. Thank you for your support anyway.
Click to expand...
Click to collapse
OK, but did you look at the second link there, to the specific post in that thread? It suggests a process for locked bootloader, which is why I thought it might help...
Anyhoo, I hope you manage to get it fixed somehow!
Is anybody have the droidboot.img file from the VibeZ K910 dualsim, pls upload it for me. i cannot find it anywhere.
I look into the second link as well. that method for user have a working phone but locked bootloader and want to downgrade.
Ah, OK. Sorry I couldn't help.
u fix your phone?
hientran41 said:
I have a VIBEZ K910 with locked bootloader after upgrading to version 4.4.2. Now it's bricked. Cannot enter test mode with the combination Volumn - and Power button. I think the droidboot.img is damaged. Cannot enter recovery either. Anybody can help me unbrick the phone? Pls:crying:
Click to expand...
Click to collapse
hi do u fix your phone?
Geguniukas said:
hi do u fix your phone?
Click to expand...
Click to collapse
i bricked also
dunno what to do..
---------- Post added at 12:13 AM ---------- Previous post was at 12:13 AM ----------
hientran41 said:
I have a VIBEZ K910 with locked bootloader after upgrading to version 4.4.2. Now it's bricked. Cannot enter test mode with the combination Volumn - and Power button. I think the droidboot.img is damaged. Cannot enter recovery either. Anybody can help me unbrick the phone? Pls:crying:
Click to expand...
Click to collapse
did you fixed the phone?
lenovo k910e 4.2.2 bricked after TWRP for 4.4.2 installation
Hi , this is my first time on the site , so forgive me if ive posted this in the wrong place.
I briked my Lenovo k910e running 4.2.2 rom with google apps purchased off Aliexpress.
What i did was run the flashrec.exe file for TWRP , but not until too late did i realise it was for 4.4.2 instead of 4.2.2.
Now i cannot boot the phone , TWRP was successfully installed and operational , but after about 20 reboots TWRP flash screen is stuck on the TeamWin logo and not accessable.
Ive tried mostl sugestions on this site and others without luck.
I can get the phone recognised with fastboot only after these commands ;
cd downloads
cd fastboot
adb devices
and it seems i may be able to push files to my device.
Is there a working link to the k910 OEM rom k910_ss_s_2_040_0109_131226 someone could direct me to.
All the links i have found so far are corrupted. Is there a way of repairing the TWRP recovery i have in the phone now.
Am I correct in assuming I have to install the OEM factory 4.2.2 ROM to wipe TWRP and istal Lenovo recovery ?.
Any help would be so appreciated. Thanks
Solution ( k910 bricked )
Ok here is the solution even if your device ( k910 dual sim ) is completely bricked as was mine.
I was stuck in Lenovo logo with no success in finding right and working drivers ( windows 7 64x ) and i was not able to to get in recovery official ...everything was just - somehow - deleted...
I had locked bootloader **** and was not be able to flash cmw in working mode ****
There was nothing for me that could recover my phone even if the "hard" way with QPST or miflash etc
So....after 3 days....find this solution and hope this will help you because it is soooooooooo easy finally!
Steps:
1) Download lenovo driver ( i think it is useless in fact but ok....just run it you dont have anything more to loose )
https://www.dropbox.com/s/frbpz16udrefoit/LenovoUsbDriver_autorun_1.0.112.exe?dl=0
2a) Download and install Minimal adb
https://www.dropbox.com/s/uvngsu4vz4hvsky/minimal_adb_fastboot_v1.1.3_setup.exe?dl=0
So now you have to use the right recovery image ( this file has to be inside minimal adb folder )....so here it is:
https://www.dropbox.com/s/ge05m1fe8n4qgb1/recovery.img?dl=0
2b)
Download this ROM ( this worked for me - with other i did try i did get an error )
http://www.needrom.com/download/lenovo-k910-vibeui-2-0/
prefer the last updated version ( 1501 )
Put this rom in the same ADB folder and renale zip in VIBE1411.ZIP ( in order to be easier later )
3) Turn off the device open Adb and write : fastboot boot recovery.img ( to have it ready )
4) Push volume + $ volume - at the same time and AFTER connect with usb to your pc - At the time the device will vibrate HIT ENTER in ADB
This will flash the recovery and after 1 minute device will open in a recovery screen with an adb update option ***
SELECT THIS adb update OPTION !
Your device kow it is ready to flash the new rom ! ( you will realize that everything is right from many usb beeps you will hear )
5)In adb console write : adb sideload VIBE1411.ZIP
This will take a little ....after that your device will reboot ! Dont panic if for a few minutes it will stuck in lenovo logo....
IT IS NORMAL AND YOU HAVE TO WAIT!
Hope this will help you.....please feel free to tell me if this worked for you.
C u
Same thing happens to my lenovo vibe z k910
buzzbuzz1 said:
Hi , this is my first time on the site , so forgive me if ive posted this in the wrong place.
I briked my Lenovo k910e running 4.2.2 rom with google apps purchased off Aliexpress.
What i did was run the flashrec.exe file for TWRP , but not until too late did i realise it was for 4.4.2 instead of 4.2.2.
Now i cannot boot the phone , TWRP was successfully installed and operational , but after about 20 reboots TWRP flash screen is stuck on the TeamWin logo and not accessable.
Ive tried mostl sugestions on this site and others without luck.
I can get the phone recognised with fastboot only after these commands ;
cd downloads
cd fastboot
adb devices
and it seems i may be able to push files to my device.
Is there a working link to the k910 OEM rom k910_ss_s_2_040_0109_131226 someone could direct me to.
All the links i have found so far are corrupted. Is there a way of repairing the TWRP recovery i have in the phone now.
Am I correct in assuming I have to install the OEM factory 4.2.2 ROM to wipe TWRP and istal Lenovo recovery ?.
Any help would be so appreciated. Thanks
Click to expand...
Click to collapse
After running twrp recovery it operates 3-4 times but now it flashes on twrp screen and screen goes blank and again flashes . I am unable to on it and as it shows only light and lenovo logo after that blank screen . Please help me in this. Its only detecting in adb recovery not any other mode.
lenove vibe Z k910 locked and stuck in logo
hello all
I ve done every word and many other tutorials but still the problem the same:
adb devices give just nothing
but fastboot devices gives the device
the driver is installed correctly detected in devices of the computer
here is the response for :fastboot boot recovery.img:
~/Desktop/lenovo]$ fastboot boot recovery.img (master✱)
< waiting for device >
downloading 'boot.img'...
OKAY [ 0.536s]
booting...
FAILED (remote: Locked)
finished. total time: 0.538s
thanks for everyone to help
Boot into recovery under bricked condition
Today I bricked K910 after reinstalling GMS apk.
The phone hanged at boot logo.
Nothing can be from here.
I decided to take this risk.
I removed the back cover and disconnected the battery terminal.
After that I plugged back the terminal.
Several tries by power button and volume down to get into the recovery mode. All failed.
Each time it hanged at boot logo.
I have to redo the battery terminal unplug sequence again.
This is correct method to get into recovery mode.
Press power button and volume down till the Lenovo logo appears.
Move the power button finger to the position of the " Home " of the touchscreen position.
Hold till the recovery menu appears. Choose factory reset to erase the phone.
There was two lit small icon below. Make your choice.
The phone will be erased by reset.
Reboot after the process.
I solved my phone bricked problem.
Hope the method will solve your problem.
Good day to all K910 users.
my vibe z cannot access the recovery mode (PWR + VLM DOWN), it only vibrate. If turn on only stuck at Logo. Please help .
I did everything that was stated in the how to's but to no avail. additionally i cant get TWRP installed via fatboot, i have checked and crosschecked usb debugging and unlock OEM , but i cant get it to work , with SP Flash my phone pops up and vanishes in the hardware manager withing fractions of a second so it doesnt work with the sp Flash , in fastboot it wont let me download to recovery even if i use the command line oem unlock , because the volume up button that you have to use to accept[yes] doesnt work , only the vol down[no ] button has an effect, anyone any ideas anyone?
?
Kylekassar said:
I did everything that was stated in the how to's but to no avail. additionally i cant get TWRP installed via fatboot, i have checked and crosschecked usb debugging and unlock OEM , but i cant get it to work , with SP Flash my phone pops up and vanishes in the hardware manager withing fractions of a second so it doesnt work with the sp Flash , in fastboot it wont let me download to recovery even if i use the command line oem unlock , because the volume up button that you have to use to accept[yes] doesnt work , only the vol down[no ] button has an effect, anyone any ideas anyone?
?
Click to expand...
Click to collapse
To use SP Flash tools, turn the phone off, press download on the software then plug the phone in. The preloader is only meant to show for a short time (a fraction of a second to a few seconds) so SPFT needs to be sending the signal to download in that time window.
What I've also found works is to press download on SPFT then press and hold power and volume up until the device starts downloading.
thx for the quick answer i will try a.s.a.p.
Kylekassar said:
thx for the quick answer i will try a.s.a.p.
Click to expand...
Click to collapse
Tried but it doesnt work , i starts the dload but then i end up on brom error : STATUS_PRELOADER_INVALID(0xC0030004) no recovery flashed
Kylekassar said:
Tried but it doesnt work , i starts the dload but then i end up on brom error : STATUS_PRELOADER_INVALID(0xC0030004) no recovery flashed
Click to expand...
Click to collapse
That could be a couple of things:
Which SPFT version are you using? If its an older version try using a newer one.
Or
The scatter file you loaded is not good, download a stock firmware and use the scatter file from that.
Try this:
fastboot flash recovery "filename".img
or
fastboot flash boot "filename".img
Do you have the MTK drivers installed? What does your phone appear as in the Device Manager? Like others have said, once you've chosen your scatter file and recovery to flash, hit download and then plug in the phone.
Managed to fix this? I have the exact same problem and not able to fix it till now....
I'm in a similar situation. I CAN get my phone to flash recovery in SPFT and get a lovely big green tick but when I power off and boot into recovery using power and volume up it boots into the stock android recovery rather than TWRP.
Going another way via ADB, I can get the phone detected but when I send the OEM unlock bootloader command I am unable to use volume up to confirm. Only the volume down key works to cancel.
All I want is to put viper4android on. Never had any issues until this phone.
chandlerp said:
I'm in a similar situation. I CAN get my phone to flash recovery in SPFT and get a lovely big green tick but when I power off and boot into recovery using power and volume up it boots into the stock android recovery rather than TWRP.
Going another way via ADB, I can get the phone detected but when I send the OEM unlock bootloader command I am unable to use volume up to confirm. Only the volume down key works to cancel.
All I want is to put viper4android on. Never had any issues until this phone.
Click to expand...
Click to collapse
Are you 100% sure the recovery.img you flashed was TWRP?
Absolutely. Downloaded from this very site. It was this one: recovery_TWRP_3021_P9000.img
---------- Post added at 02:23 PM ---------- Previous post was at 02:17 PM ----------
Did an OTA update this morning and am showing as on build number Elephone_P9000_20160608 now. Haven't tried flashing since the update as I'm at work with locked down computers. Was going to try again over the weekend. Which recovery and version of flash tools would you recommend trying this time?
thanks for any advice.
Actually I have the same problem.
I tried to reinstall the drivers because it seems to be not the correct one. Here is a pic: i.imgur.com/FoUnVyz.png
After I read somewhere that i can try and hold down Volume+ while connecting my phone to the pc where i started the download in sp tools prior.
I got this error code: STATUS_PRELOADER_INVALID(0xC0030004)
And here I am with a not-up-to-date elephone p9000.
Anybody care to help me?
I'm in the same situation, tried everything - flashtool recovery.img separate in download mode, flashtool in update mode full 7.0 with replaced original recovery.img with TWRP one, played with fastboot with no luck as did not find the way to OEM UNLOCK it - vol + not reacting. Bought the phone on Gearbest, looks like it's locked very hard.
Can't install TWRP
Me too! I've updated my p9000 to latest stock v7 rom with spft. I can't install twrp recovery despite getting a geen tick from spft. Tried four times but it won't overwrite the stock rom recovery. A locked bootloader seems to be the popular diagnosis but spft doesn't use the bootloader. What else could it be? Ideas very welcome.
Did you boot into recovery immediately after flashing? A normal system boot will overwrite TWRP with the stock recovery. Once you start TWRP there is an option to prevent this from happening.
Can't install TWRP
Thanks for the suggestion. I flashed twrp again but it won't boot into recovery afterwards without a restart, just hangs. Stiĺl on stock recovery.
I would like to know if someone could make a custom recovery and a stock version of android that I could put on my Blu Pure XR. I don't care if get rid of the 3d Touch on the phone. I just would like to have the stock android interface again and probably also the ram management will be better on the stock version.
I have the same request, would love to see TWRP. I'd like to install pixel launcher as system app and remove the adsup fota spyware.
The Pure XR is otherwise a great phone. Power management on stock is fantastic, i can get 6-7 hours of screen on time.
The Pure XR is essentially a Gionee S8 but sadly I dont see any custom recovery or development interest for that either.
Include me as well. Thanks
So the Pure XR is similar/same to the Symphony Helio S20...
There's a thread here that has a working twrp: https://forum.xda-developers.com/android/general/how-to-root-symphony-helio-s20-t3491123
I tested the recovery.img by loading it with fastboot without flashing and it worked!
You'll need adb/fastboot and the drivers first. Then boot the phone into fastboot mode by holding power + Up keys.
Select fastboot. After that, run: fasboot devices to make sure your phone is detected. Once detected:
fastboot oem unlock
reboot the phone, it'll do a force wipe
hold power+up keys again and boot to fastboot mode
Now, run this on your PC: fastboot boot recovery.img
Once the image is transferred, the screen goes blank...wait a min or two and TWRP will show up.
rom/firmware blu pure xr?
Anyone found a good stock ROM/Firmware for the Blu Pure XR?
if you finde one just tell us
ishman27 said:
Anyone found a good stock ROM/Firmware for the Blu Pure XR?
Click to expand...
Click to collapse
if you finde one just tell us
exciter0 said:
So the Pure XR is similar/same to the Symphony Helio S20...
There's a thread here that has a working twrp: https://forum.xda-developers.com/android/general/how-to-root-symphony-helio-s20-t3491123
I tested the recovery.img by loading it with fastboot without flashing and it worked!
You'll need adb/fastboot and the drivers first. Then boot the phone into fastboot mode by holding power + Up keys.
Select fastboot. After that, run: fasboot devices to make sure your phone is detected. Once detected:
fastboot oem unlock
reboot the phone, it'll do a force wipe
hold power+up keys again and boot to fastboot mode
Now, run this on your PC: fastboot boot recovery.img
Once the image is transferred, the screen goes blank...wait a min or two and TWRP will show up.
Click to expand...
Click to collapse
When I connect the phone through Fastboot and enter the command "fastboot devices," the phone is never recognized. I'm using Windows 10. Any help would be appreciated.
I used Linux instead. Have you installed the mtk and adb windows drivers?
exciter0 said:
I used Linux instead. Have you installed the mtk and adb windows drivers?
Click to expand...
Click to collapse
Yes, I installed the mtk and adb drivers however while adb works and detects my phone, fastboot does not.
Ok, I attempted using the SP Flash Tool on Windows 10 and successfully installed TWRP and rooted the phone. The only flaws are that the phone takes a few minutes to load into TWRP and unfortunately, there are still no custom roms on the device. It is a good start however.
Galaxxus_Rosarrius said:
Ok, I attempted using the SP Flash Tool on Windows 10 and successfully installed TWRP and rooted the phone. The only flaws are that the phone takes a few minutes to load into TWRP and unfortunately, there are still no custom roms on the device. It is a good start however.
Click to expand...
Click to collapse
Hey bud, big favor, would you describe step by step the rooting process, I used SP Flash Tool on windows 7 to install TWRP and it gave the ok check marK, then I tried to boot into recovery and I found out that TWRP was not installed. Do you have to unlock the bootloader to be able to install TWRP using SP Flash Tool? Thanks in advance.
Sent from my SM-G935T using XDA-Developers Legacy app
Hello everyone, I need your help, I've been trying to unlock my bootloader to root my phone, under setings I have developer options-OEM UNLOCK, but I only get as far as FASTBOOT MODE using my laptop as well as my pc, I tried this process with Windows 10, Windows 7 and latest Ubuntu. I tried different data cables, different usb ports 2.0 and 3.0 and nothing seems to work, I can put the phone on FASTBOOT MODE with my pc or lap, but then after that it looks to me that there is no comunication between my pc and phone. I installed all drivers several times and under DEVICE MANAGER everything looks good, as far as data cables I'm using 2 blu original data cables as well as aftermarket ones. Any help will be appreciated. Thanks in advance and have a good day.
Sent from my SM-G900T using XDA-Developers Legacy app
oscarmaldonado said:
Hey bud, big favor, would you describe step by step the rooting process, I used SP Flash Tool on windows 7 to install TWRP and it gave the ok check marK, then I tried to boot into recovery and I found out that TWRP was not installed. Do you have to unlock the bootloader to be able to install TWRP using SP Flash Tool? Thanks in advance.
Sent from my SM-G935T using XDA-Developers Legacy app
Click to expand...
Click to collapse
I remember something similar to this happening to me when I used a different version of SP Flash tool. Try SP Flash Tool v5.1624.00.000. After this make sure you have the scatter file for the MT6755 as well as the recovery file for the phone. Make sure that you have selected the scatter file for the phone and that the recovery.img is in the same directory as the scatter file.
Once this is done, make sure that you have installed the preloader or VCOM driver for the phone. This is tricky as the opportunity to apply the correct driver comes when you are powering on the phone and in this time you must click on the device that pops up in this time, right click it, and click properties.
Once this is done, go back to SP Flash Tool and click download, your phone must be off and unplugged before doing this. Then after this step, plug in your phone and the download process should begin (this might take a while). After this, boot into recovery mode which also will take around 3-5 minutes maybe more. After this you will have TWRP installed and from there you can install various apps including SU.
Galaxxus_Rosarrius said:
I remember something similar to this happening to me when I used a different version of SP Flash tool. Try SP Flash Tool v5.1624.00.000. After this make sure you have the scatter file for the MT6755 as well as the recovery file for the phone. Make sure that you have selected the scatter file for the phone and that the recovery.img is in the same directory as the scatter file.
Once this is done, make sure that you have installed the preloader or VCOM driver for the phone. This is tricky as the opportunity to apply the correct driver comes when you are powering on the phone and in this time you must click on the device that pops up in this time, right click it, and click properties.
Once this is done, go back to SP Flash Tool and click download, your phone must be off and unplugged before doing this. Then after this step, plug in your phone and the download process should begin (this might take a while). After this, boot into recovery mode which also will take around 3-5 minutes maybe more. After this you will have TWRP installed and from there you can install various apps including SU.
Click to expand...
Click to collapse
Thank you very much, I'm gonna give it a try as soon as I get a chance, I'll report back. Thanks again.
Sent from my SM-N910T3 using XDA-Developers Legacy app
Hi everyone, TWRP has been released by lopestom here https://forum.xda-developers.com/pure-xr/development/twrp-twrp-3-1-x-x-blu-pure-xr-p0030-t3623865
Since the Pure XR threads are very slim here I thought I'd post this here.
Seems my XR's data has got very slow, signal strength weak, etc.
Trying to figure out if this is Cricket or something up with the phone. My wife has a Blu Life one X3 and the same Cricket and her signal and data speeds are always better than mine.
What are some things to check/look for? I've tried a few like manually choosing the Network, changing the APN settings, etc.
Any further advice would be greatly appreciated.
Hi...
I try to root my FL02 (ALCATEL FLASH PLUS 2) every thing goes perfect and i get ORANGE STATUS but at the last step when trying to flash the rom with TWRP it could not read the SD card and system folder isn't abel to wipe so i try to repeat steps again.
first flasing in the video done and mobile restarting. no logo on screen and it doesnt boot and cannt go in boot mode or fastboot mode.
it connect and disconnect with PC but i still can connect it to flashing programme and i can send flash from PC but it doesnt boot and nothing appear on the screen.
any help....
Phone : FLASH PLUS 2
N D1M N7KE 03 TJZ
ANDROID 6.0
I follow this video to root
youtube.com/watch?v=d8zPGPJ_uZY
EFAYSAL said:
Hi...
I try to root my FL02 (ALCATEL FLASH PLUS 2) every thing goes perfect and i get ORANGE STATUS but at the last step when trying to flash the rom with TWRP it could not read the SD card and system folder isn't abel to wipe so i try to repeat steps again.
first flasing in the video done and mobile restarting. no logo on screen and it doesnt boot and cannt go in boot mode or fastboot mode.
it connect and disconnect with PC but i still can connect it to flashing programme and i can send flash from PC but it doesnt boot and nothing appear on the screen.
any help....
Phone : FLASH PLUS 2
N D1M N7KE 03 TJZ
ANDROID 6.0
I follow this video to root
youtube.com/watch?v=d8zPGPJ_uZY
Click to expand...
Click to collapse
Ok, tell me to can help you;
Do you have TWRP installed?
Do you unlock bootloader succesfully?
In which modes you can enter? fastboot, recovery, download (do detects SPFlash Tool?)
SubwayChamp said:
Ok, tell me to can help you;
Do you have TWRP installed?
Do you unlock bootloader succesfully?
In which modes you can enter? fastboot, recovery, download (do detects SPFlash Tool?)
Click to expand...
Click to collapse
Thank you SubwayChamp for help.
No , TWRP is not installed now .
Yes, I think bootloader has been unlocked. It is done with Orange status.
I think it is in download mode. it detects SPFlash.
EFAYSAL said:
Thank you SubwayChamp for help.
No , TWRP is not installed now .
Yes, I think bootloader has been unlocked. It is done with Orange status.
I think it is in download mode. it detects SPFlash.
Click to expand...
Click to collapse
Ok, I guess that your device is actually in bootloop and don´t booting.
Tutorial that you followed has many steps and don´t need to do all this to just root device and it contains some files like lk.bin that you can´t be sure that should be for your device.
Some users use this file (lk.bin) of an unlocked device and think that flashng in other device then get unlock it but no need, your device can be unlock it just follow some commands in fastboot mode.
Now you can do the next;
Try to flash again your rom stock (I guess that you don´t have a backup), if for some reason your official tool doesn´t work then use only some images like boot, system and userdata with the scatter.txt to flash them through SP Flash Tool.
Here a link to TWRP https://youtu.be/6vj_BY6xJdA, you can root it with supersu v2.78 0r v2.82 and here some files that can be usefull too https://drive.google.com/uc?id=0BwJgeCYTpnEHNlg2VUlieHFTYVU&export=download
Update steps that you are following to can assist. What extension has your rom and if it is recogniced for SP Flash Tool. I didn´t ask you if you can enter to fastboot mode and if you can then you can know if your bootloader is unlocked typing fastboot oem info
Most info that you give and some screenie will help to understand better
Unfortunatly, it can not enter to fastboot or recovery mode. Those files in replay didn't work and i dont have a backup. I try to flash recovery.img, system.img and preloader_shine_plus.bin . All done but it still black screen and does not boot. But now it connect to Pc without disconect .
I cant add link or images to my post.
EFAYSAL said:
Unfortunatly, it can not enter to fastboot or recovery mode. Those files in replay didn't work and i dont have a backup. I try to flash recovery.img, system.img and preloader_shine_plus.bin . All done but it still black screen and does not boot. But now it connect to Pc without disconect .
I cant add link or images to my post.
Click to expand...
Click to collapse
Gmail didn´t warn myself about your post. Did you solve it?
You said that flashed recovery, system and preloader but how, through SPFlashTool?, if yes, are you sure that this tool recogniced your device?
You forgot to flash boot.img too.
Other way to try; flash only preloader.bin and then try flashing boot, system and userdata that are the three most important partitions to can boot.
Like last resort you can do a Format all + flash but only like last.
SubwayChamp said:
Gmail didn´t warn myself about your post. Did you solve it?
You said that flashed recovery, system and preloader but how, through SPFlashTool?, if yes, are you sure that this tool recogniced your device?
You forgot to flash boot.img too.
Other way to try; flash only preloader.bin and then try flashing boot, system and userdata that are the three most important partitions to can boot.
Like last resort you can do a Format all + flash but only like last.
Click to expand...
Click to collapse
first of all thank you for your help. I was busy last week .
Yes it was with SPFlash and it is show MT6775 when mobile connect . but if i try flashing boot it gives an erorr and cant flashing.
I think i have a wrong boot file.
I miss userdata file.
Do you know where can i download necessary files for this model?
I apologize for delaying. It is time for school examin
EFAYSAL said:
first of all thank you for your help. I was busy last week .
Yes it was with SPFlash and it is show MT6775 when mobile connect . but if i try flashing boot it gives an erorr and cant flashing.
I think i have a wrong boot file.
I miss userdata file.
Do you know where can i download necessary files for this model?
I apologize for delaying. It is time for school examin
Click to expand...
Click to collapse
I´m not sure if you are connecting correctly your device at right time and form to can flash it properly. Every device has more or less a specific way to do it. My last alcatel it was connected just with device power off and after to tap on download, but in other device Blu Dash was connected pressing just vol_up and my last mt6757 Bluboo had to press both vol up and down at time to connect to pc and after to tap on download option. To have sure that is well done increase volume in your pc, you will hear a first sound that is cause pc is recognicing but then you have to hear a second sound that is when SPFlashTool is recognicing device and you will see a red line in down side of the tool window, release button inmediately and let tool to work.
This is a good rom for your device according the author is optimized https://droid1311.blogspot.com/2017/08/alcatel-fl02-aka-flash-plus-2-via.html and this is the link directly if you have troubles with pop-up-adds https://drive.google.com/file/d/0BwAGh1drb91SeDZwV1VXbXpjQWM/view
Also you can try with other versions of SP Flash Tool, most stable maybe should be v5,1628 https://androidmtk.com/smart-phone-flash-tool leth me know how you go
If I understant, the status bar has to be red then I will release the mobile button and click download in SPFlashTool.
SPFlashTool 5.1628:
I try all the way with and without pressing any button but no luck . And when it work finishing with error.
SPFlashTool 5.1628:
I try all the way to get that mode but nothing works. So I try to click download button then conect the phone by random buttons and every time i get red color , yellow , green ,purple , yellow (for many times 100%)
then i get this error:
ERR: STATUS-SEC-IMG-TYPE-MISMATCH (0xC002002A)
EFAYSAL said:
If I understant, the status bar has to be red then I will release the mobile button and click download in SPFlashTool.
I try all the way to get that mode but nothing works. So I try to click download button then conect the pkone by random buttons and every time i get red color , yellow , green ,purple , yellow (for many times 100%)
then i get this error:
ERR: STATUS-SEC-IMG-TYPE-MISMATCH (0xC002002A)
Click to expand...
Click to collapse
There is a part that is not variable in the way to use this tool, ever you have to tap on download before to connect device and is recommendable too connect cable usb to pc (not yet to device); from here is when the button that you have to press can vary but like I said you before in my last mt6757 (a very similar to yours) works pressing both vol at same time to connect terminal cable to device and now you will see a red line (could be violet-ish)
Try before just flashing only preloader file to recreate some partitions and then do other flash for the other files.
Of course you have to be sure that all drivers are installed correctly cause this tool needs to put your device in download mode (a special level) and also keep it in this state so find VCOM drivers for Alcatel and adb/fastboot installer and try to uninstalling some older drivers that you don´t use and many times we keep in our pcs and for a short data transmission can helo that all the rom move it in same folder where SPFlashTool is allocated.
After updating drivers and trying all the possibilities buttons the red line doesnt appear.
EFAYSAL said:
After updating drivers and trying all the possibilities buttons the red line doesnt appear.
Click to expand...
Click to collapse
Ok, here there are somethings that we need to know
- First of all don´t forget to charge your battery, after many attempts could consume a lot.
- Your device is recogniced in fastboot mode? mtk has two variables ways to enter to, pressing both vol + pwr till an options menu appear, then you have to select, and the other method most known is vol down+ pwr to go diirectly
- In what android version are you, 6.0?
- What is the exact variant of your device, you can know maybe seeing in the box, this rom is for 5095K version 6.0 MM
- Did you try to flash just preloader, only this file?
If SPFlashTool don´t give signals of recognicing device is probably that your device is not now totally power off, try pressing pwr by 7 seconds, then try to flash again combining both vol with pwr button
Upload some screenshot about the process
SubwayChamp said:
Ok, here there are somethings that we need to know
- First of all don´t forget to charge your battery, after many attempts could consume a lot.
- Your device is recogniced in fastboot mode? mtk has two variables ways to enter to, pressing both vol + pwr till an options menu appear, then you have to select, and the other method most known is vol down+ pwr to go diirectly
Click to expand...
Click to collapse
Which option mode should appear? Screen is always black (off) all that i have on the phone is the LED.
I try more than 4 different drivers for Alcatel Flash Plus 2 (vcom & cdc) but no sound from SPFlash to prove that it recognise the phone. Sounds just release and keep relrease from Windows 10.
SubwayChamp said:
- In what android version are you, 6.0?
Click to expand...
Click to collapse
Yes, last time it was 6.0 before the root
SubwayChamp said:
- What is the exact variant of your device, you can know maybe seeing in the box, this rom is for 5095K version 6.0 MM
Click to expand...
Click to collapse
Unfortunatly, I dont know . There is nothing on the box or manuel.
that is what i found on the box :
FL02
Venus gold H-B
FL02-2HLCEU2
- PWR+VOL(+) : reset the phone
SubwayChamp said:
- Did you try to flash just preloader, only this file?
Click to expand...
Click to collapse
It is done. all that i have to do is to tab on Download and then connect the phone and I dont need to press any button.
SubwayChamp said:
If SPFlashTool don´t give signals of recognicing device is probably that your device is not now totally power off, try pressing pwr by 7 seconds, then try to flash again combining both vol with pwr button
Upload some screenshot about the process
Click to expand...
Click to collapse
I did that but it is same.
Note:
Success fash always done without pressing any button on the phone. and I try it with and without buttons sometimes it is fail when I press a button and otherwise it work.
I have formated whole fash.
EFAYSAL said:
Which option mode should appear? Screen is always black (off) all that i have on the phone is the LED.
I try more than 4 different drivers for Alcatel Flash Plus 2 (vcom & cdc) but no sound from SPFlash to prove that it recognise the phone. Sounds just release and keep relrease from Windows 10.
Yes, last time it was 6.0 before the root
Unfortunatly, I dont know . There is nothing on the box or manuel.
that is what i found on the box :
FL02
Venus gold H-B
FL02-2HLCEU2
- PWR+VOL(+) : reset the phone
It is done. all that i have to do is to tab on Download and then connect the phone and I dont need to press any button.
I did that but it is same.
Note:
Success fash always done without pressing any button on the phone. and I try it with and without buttons sometimes it is fail when I press a button and otherwise it work.
I have formated whole fash.
Click to expand...
Click to collapse
You need to try two different ways to flash files and restore your device.
First method: fastboot mode
You need to get device enter to fastboot in order to flash some files like system, boot and userdata, then there are two main methods to do it:
- Pressing pwr + vol down
- And I mentioned that sometimes work pressing both volume button + pwr and a menu have to appear to can select an option to enter to (fastboot mode), in some devices this method is not working but you have to try several times attempting to.
Second method: SPFlashTool
You have to ever press first of all Download box and connect terminal cable to pc and the buttons thhat you need to press at time to connec cable usb to your device may vary, sometimes vol down, sometimes both vol but never pwr button; if pc recognice then you have to release all buttone an let it pc continue the flash process.
If SPFlashTool recognice device first flash only preloader file and select now lk.bin too. Flash only these two files and after do again a new flash with the rest of the files, Why you need to do this? your partitions are corrupted and you need to restore them with these files in order to can flash all another files.
Before all of this charge your battery, if you have a cover removable then extract it some minutes and put it again.
Also I read that for this model it´s used this tool instead of SPFlash Tool https://androidmtk.com/download-sugar-mtk-sp-flash-tool (inside the zip you will find a password to start the tool) but I´m not sure what kind of rom it needs, you have to connect your device to begin the process, you will find in product models section in the tool this variant for your device "FL02"
Try first the other tool and then this and let me know how you go, mtk devices are almost unbrickeable so it´s just to find the appropriate way to return it to the life.
Hi again!
It was along time,I know . But I tried to know why I can’t return my phone back to life.
I have searched all possible websites for rom of this model and I have formatted my pc and installed win7 with all necessary drivers.
I can’t found any rom for it but now I can flash all the necessary files for boot they flashing and running smoothly but the mobile can’t boot up.
I try to use that app in your replay. It recognizes the device but stuck after that and keep looking for rom without any chance to download it.
I think I have a wrong rom files. I can’t find any other reason but this.
I will write again all information about my phone:
It is called Alcatel Flash Plus 2
I bought it from AliExpress and it came from Indonesia as I remember (not sure)
On battery wrote:
FL02
TCL communication Ltd
FL02-2HLCEU2
EFAYSAL said:
Hi again!
It was along time,I know . But I tried to know why I can’t return my phone back to life.
I have searched all possible websites for rom of this model and I have formatted my pc and installed win7 with all necessary drivers.
I can’t found any rom for it but now I can flash all the necessary files for boot they flashing and running smoothly but the mobile can’t boot up.
I try to use that app in your replay. It recognizes the device but stuck after that and keep looking for rom without any chance to download it.
I think I have a wrong rom files. I can’t find any other reason but this.
I will write again all information about my phone:
It is called Alcatel Flash Plus 2
I bought it from AliExpress and it came from Indonesia as I remember (not sure)
On battery wrote:
FL02
TCL communication Ltd
FL02-2HLCEU2
Click to expand...
Click to collapse
Yes, so many time
When device is booting, it stays in bootlogo or goes atleast to bootanimation?
I understand that you tried with Sugar tool with no lucky.
Did you try again through SP Flash tool? trying to flash in a first attempt only preloader file and in a second attempt the other files? (try with 2 or 3 versions and see the differences).
Is there some custom development, recovery, roms for your device?
I think that now you are flashing correct rom through fastboot but like you did before bad/wrong flashings your bootloader is refusing to boot to system. Flash through fastboot all the partitions that you can follow the syntax for every one of them by i.e. typing fastboot flash cache cache.img and so on one by one (some of them are unflashable through this method)
SubwayChamp said:
Yes, so many time
When device is booting, it stays in bootlogo or goes atleast to bootanimation?
Click to expand...
Click to collapse
Unfortunately, nothing happens. The screen is black no bootlogo appears or anything that shows that device is booting. It is looking like nothing has happened.
SubwayChamp said:
I understand that you tried with Sugar tool with no lucky.
Click to expand...
Click to collapse
Yes. After recognizing it keeps trying to download data but no luck.
SubwayChamp said:
Did you try again through SP Flash tool? trying to flash in a first attempt only preloader file and in a second attempt the other files? (try with 2 or 3 versions and see the differences).
Click to expand...
Click to collapse
I know it is disappointing!. I try this but no luck.
SubwayChamp said:
Is there some custom development, recovery, roms for your device?
Click to expand...
Click to collapse
Unfortunately no, all that I found are TWRP recovery Roms. I don’t know if I can use them with SPFLASH Tool.
SubwayChamp said:
I think that now you are flashing correct rom through fastboot but like you did before bad/wrong flashings your bootloader is refusing to boot to system. Flash through fastboot all the partitions that you can follow the syntax for every one of them by i.e. typing fastboot flash cache cache.img and so on one by one (some of them are unflashable through this method)
Click to expand...
Click to collapse
I began lose hope that the mobile could work again. I live in Sweden and no technicians kan help me to fix this issue. I should do it by myself.
If you kan help me to do that step by step. Please write to me what I have to do from the beginning step by step until I reach the end. To be sure I'm doing it by the right way.
Thanks
EFAYSAL said:
Unfortunately, nothing happens. The screen is black no bootlogo appears or anything that shows that device is booting. It is looking like nothing has happened.
Yes. After recognizing it keeps trying to download data but no luck.
I know it is disappointing!. I try this but no luck.
Unfortunately no, all that I found are TWRP recovery Roms. I don’t know if I can use them with SPFLASH Tool.
I began lose hope that the mobile could work again. I live in Sweden and no technicians kan help me to fix this issue. I should do it by myself.
If you kan help me to do that step by step. Please write to me what I have to do from the beginning step by step until I reach the end. To be sure I'm doing it by the right way.
Thanks
Click to expand...
Click to collapse
I´ll tell you some ideas with no any specific order that you can try or see if works.
Really very strange that display stays in black, you told me that flashing files through fastboot is working but doesn´t appear not even bootlogo, connect to pc as it is and see how pc recognices in devices manager and my pc if appears like a determined drive d/e/f so it looks that some bad flashing burn your kernel and this case is similar to when a Samsung device need to use jtag method to revive, if in your country no-one knows about Alcatel devices this could be a similar case to what I´m saying then it could be a clue for a technician. I tell you this cause many time ago when I flashed by error a Samsung s4 and only this method revived my device.
Try this, flash your stock recovery only through SPFlash tool and flash after through Alcatel Download tool your stock rom cause some firmwares need to detect stock recovery first to can flash other partitions.
At this stage don´t you have stock recovery, no? so you can try to format data cause sometimes when bootloader is altered then avoid to boot and formatting data can solve this.
If this recovery twrp is for your device you can try flashing through SPFlash tool, you have to put recovery.img and scatter-txt in a same folder. then if succesfull format data, system, wipe cache and dalvik and maybe later try to port some custom rom would be a way to solve this.
To flash any partition through fastboot this is the syntax, just follow one by one any of the files that are in your rom folder so just follow these, if some of then can´t be flashed don´t worry then it´s not flashable:
fastboot flash boot bot.img
fastboot flash cache cache.img
fastboot flash lk lk.bin
and so on till the end
...But after try this if you didn´t get boot to recovery and obviously you can´t delete data nor system then delete first the next partitions trough fastboot typing:
fastboot erase system
fastboot erase cache
fastboot erase userdata
fastboot erase boot
Try all this and let us see how it goes
I have flashed TWRP Rom but it is same , no luck.
On sugar tool I got this message after success flashing via SPFLASH tool.
I tried all possible buttons to connect device to PC on Fastboot mode but the PC cannot send data to my device.
To be in Fastboot mode , the device has to boot while pressing on (PWR & VOL+) but my device can’t boot.
EFAYSAL said:
I have flashed TWRP Rom but it is same , no luck.
On sugar tool I got this message after success flashing via SPFLASH tool.
View attachment 4518365
I tried all possible buttons to connect device to PC on Fastboot mode but the PC cannot send data to my device.
To be in Fastboot mode , the device has to boot while pressing on (PWR & VOL+) but my device can’t boot.
Click to expand...
Click to collapse
I see that Sugar tool detects your device like rooted and refuses to flash anything, compare imei number which is in the box, I hope that it couldn´t be changed.
Don´t tell me simply no luck, what it says in SPFlash tool when you tried to flash TWRP and I guess that you put scatter-txt and twrp renamed recovery.img simply in the same folder. Just to be clear, to can flash with this tool your device it has to be off not needed fastboot for this. (provide some screenie)
Other combination of keys to enter to fastboot to flash some partitions when something is missing is, try these three ways:
- Pressing only vol down and at same time connecting to charger (connect first one terminal of cable to your device and then to the charger)
- Pressing the three buttons till a menu appears (you must to release inmediately all)
- Pressing vol up + pwr till a menu appears (you must to release pwr button inmediately) then choose fastboot
In the post 4 I provided a link from Google Drive, in this zip there are 8 items;
- From the item 2 use this version of SP Flash tool, put the four files in a folder and flash them
- In the item 3 you will find some scripts for fastboot, maybe they´re working better and also you have here a subfolder with twrp image.
- And if you get sucessfully install twrp in the item 7 there is a backup with some files to restore from this recovery.
Try one by one and update the info, I hope that your motherboard is not damaged.