Related
Got my new LG L9 and, after upgrading to V20B via OTA, I decided to downgrade to V10A to get it rooted (this was before I discovered this thread :/).
Here is what I did:
- I successfully used the KDZ_Flash-Package_LG to downgrade.
- Had to hard reset, then the phone booted fine.
- Rooted using Bin4ry's method
- Installed some L9RecoveryInstaller_1.3.0.apk for CWM (I think this is where I might have f***ed up?)
- Got into CWM recovery just fine, then flashed the lates CM nightlies (from here) +gapps (or maybe this was stupid?)
- Rebooted (wiped all data, cache & dalvik)
Now the phone is stuck at the "Securty Error" screen. The situation:
- Hard reset doesn't help....
- ...but I can get into the S/W screen just fine!
- The devices COM port shows up in device manager
- ...but not the ADB
The LGMobile Support Tool does recognize the device just fine and I can start the phone update process, however, my Internet right now is dead slow, so I'd be waiting for 8 hours for the download to complete (with a chance of things going wrong, again).
I hoped I could flash using the offline KDZ flasher again (as I did previously). However, it keeps complaining that my phone is not connected. I assume this has to do with the fact that the ADB is not initialized?
Anybody knows a way out of this? How to get the ADB up while in S/W mode?
Or at least some feedback on where exactly I made the mistake, so I can learn for the future?
Edit1: Note that I did make a backup of the phone in V10A state, so getting back into recovery would also help!
Edit2: Could this "fastboot" thing help? If I got the phone into fastboot mode, what specifically could I do to unbrick?
Cm won't work without unlocked bootloader. SW is a bit flaky in JB. What you need to do is get p1 (xloader) and p2(uboot) dump from same variant phone as you have. These dumps need to be from ICS then you have to use fastboot to flash them. S/W mode should work fine after that. I'll update my post with more details when I have more time.
Try getting p1 and p2 from someone first
Thank you so much for your response!
Lelus said:
Try getting p1 and p2 from someone first
Click to expand...
Click to collapse
Who would be so kind?
Edit: I played around a little and I already manged to get into fastboot mode following this thread. So all I need now are these p1/p2 dumps? Is there any chance on finding this on the web, in case nobody can provide me with some, here? Also, with "ICE", you mean "ice cream sandwich / ics" version of android, right?
jaaaaaan said:
Thank you so much for your response!
Who would be so kind?
Edit: I played around a little and I already manged to get into fastboot mode following this thread. So all I need now are these p1/p2 dumps? Is there any chance on finding this on the web, in case nobody can provide me with some, here? Also, with "ICE", you mean "ice cream sandwich / ics" version of android, right?
Click to expand...
Click to collapse
Yes, ics. I don't think you can find it on the web. I'll post instructions how to dump p1&2 later.
R: [Q] LG L9 / p760 stuck at "security error". How to get ADB up?
Hi, I can provvide x-loader and u-boot from ICS but I think you need the boot.img (kernel) because you flashed the cm's kernel with locked bootloader and that caused the security error.
Anyway with LG mobile support tool you can configure an http server to download the kdz from your PC (VERY fast).
As soon as I get home I will post x-loader, u-boot and boot.img from ICS
Inviato dal mio LG-P760 con Tapatalk 2
Thank you again for your response! So the backups posted in this thread would not help me, right? I need dumps of unrooted p1/p2's...
@sguerrini97: - almost missed your response , thanks for getting back at me, and thanks for your offer to help me! I'm looking forward to get this fixed again
You are welcome
Here is a boot.img from p760: https://dl.dropbox.com/u/95188513/Android/boot.img
And here is the x-loader: https://dl.dropbox.com/u/95188513/Android/x-loader.img
They are from V10H. Unfortunatly I can't find my dump of ICS' u-boot, anyway I think you only need the boot.img.
Once you get in fastboot mode, run this command:
Code:
fastboot flash boot boot.img
This should fix the security error...
To get adb working you can boot into LG's stock recovery if you didn't flash CWM from fastboot ([vol+] + [home] + [power]).
If you flashed another recovery (not the 2nd-init recovery, but a real recovery) here is the stock recovery.img: https://dl.dropbox.com/u/95188513/Android/recovery.img
You can flash this with fastboot too:
Code:
fastboot flash recovery recovery.img
Keep us updated on your situation
- flashed your boot.img:
- still security error
- flashed both your x-loader.img and the recovery.img you provided:
- still security error
- tried to get into the LG recovery mode anyway:
- YES! ADB Interface in device manager!
- Tried to flash V10A using LGMobile Software Tool (was the only image I ever managed to get offline):
- used "emergency" phone mode
- went through "ANALYSIS" and "DOWNLOAD" without problems...
- ...but now is stuck at 4% of UPDATE for 10 minutes now already
- (log appended)
I'm still having the update open. Should I pull the plug? What to try next? Try again? Different PhoneMode?
Again, thank you so much for your support!
Code:
22:26:07 : [C:\LGMobileUpgrade] Try to delete folder
22:26:07 : Start Date : 2013-03-29 22:26:07
22:26:07 : ---------- QM Testmode ---------
22:26:07 : ***** Check Tool Version *****
22:26:07 : Tool version : 1.5.4.8
22:26:07 : UpgradeDLL version : 1.2.6.7
22:26:07 : Current Dir : C:\ProgramData\LGMOBILEAX\B2C_Client
22:26:07 : LGE USB Driver Version :
22:26:07 : Android PDLV Version :
22:26:07 : Android NDLV Version :
22:26:07 : ******************************************
22:26:07 : [C:\ProgramData\LGMOBILEAX\Phone] Try to delete folder
22:26:07 : SetEmerModeAT()
22:26:07 : _IsConnectedPhone Call
22:26:23 : _IsConnectedPhone(1)
22:26:23 : 0 - NotConnected.
22:26:23 : 1 - Normal connect success
22:26:23 : 2 - Emergency connect success
22:26:25 : _IsConnectedPhone Call for SmartPhone
22:26:25 : _IsConnectedPhone(0)
22:26:25 : 0 - NotConnected.
22:26:25 : 1 - Normal connect success
22:26:25 : 2 - Emergency connect success
22:26:25 : PhoneÀÌ Notconnect »óÅÂÀ̸ç Port¸¦ ÀâÁö ¸øÇß°í Åë½Å ÇÒ¼ö¾ø´Â »óÅÂÀÓ.
22:26:25 : ¾÷±×·¹À̵å ÇÏ´Ù°¡ ½ÇÆÐÇÑ ±â·ÏÀÌ PC¿¡ ³²¾ÆÀÖÀ¸¸ç Æù°ú Åë½ÅÀ» ÇÒ¼ö ¾ø±â ¶§¹®¿¡
22:26:25 : ȯ°æºÐ¼® ´ë½Å ¸¶Áö¸·¿¡ ¾÷±×·¹À̵带 ½ÃµµÇÑ °ªÀ» °¡Áö°í ¾÷±×·¹ÀÌµå ½Ãµµ¸¦ ÇÔ.
22:26:25 : ȯ°æ ºÐ¼® ºÎºÐÀº Pass ÇÏ°í File download / Decrypt °úÁ¤À¸·Î PassÇÔ.
22:26:25 : *****CheckOS Start********
22:26:25 : Microsoft_Windows_XP_Professional_Service Pack 3
22:26:25 : ÀÎÁõ °Ë»ç ÆĶó¸ÞŸ - ESN_IMEI : , Model :
22:26:25 : Phone type Compare start
22:26:26 : ****************CheckAndDownload********************
22:26:26 : ******Extract Start C:\Users\Jan\Desktop\P760\root\rollback\V10A_00.kdz*****
22:26:26 : Model Dll Dir(C:\ProgramData\LGMOBILEAX\Phone\)
22:26:26 : File Size = 532966984
22:26:38 : Extract kdz file Success.
22:26:47 : Extracted C:\ProgramData\LGMOBILEAX\Phone\\V10A.wdb\n
22:26:47 : WDB(or DZ) FullPath(C:\ProgramData\LGMOBILEAX\Phone\\V10A.wdb)
22:26:53 : Extracted C:\ProgramData\LGMOBILEAX\Phone\\LGP760.dll\n
22:26:53 : Model dll FullPath(C:\ProgramData\LGMOBILEAX\Phone\\LGP760.dll)
22:26:53 : NNNNN WDB FullPath(C:\ProgramData\LGMOBILEAX\Phone\V10A.wdb)
22:26:53 : NNNNN Model dll FullPath(C:\ProgramData\LGMOBILEAX\Phone\LGP760.dll)
22:26:53 : Extract End C:\Users\Jan\Desktop\P760\root\rollback\V10A_00.cab
22:26:53 : ------------------Model.dll Information-------------------
22:26:53 : Filename : LGP760.dll
22:26:53 : Version : 0.0.1.0
22:26:53 : File size : 270336
22:26:53 : File date : 2012/06/14-15:49:00
22:26:53 : PC Created date: 2013/03/29-22:26:47
22:26:53 : ----------------------------------------------------------
22:26:53 : *****Check LGCM Programs Start*****
22:26:53 : LGCM Programs Not Found - OK and ready to upgrade
22:26:53 : *****WorkModelDLL Start*****
22:26:54 : strPhoneBinaryPath(C:\ProgramData\LGMOBILEAX\Phone\V10A.wdb)
22:26:54 : strModuleDir(C:\ProgramData\LGMOBILEAX\Phone\)
22:26:54 : strModelDLLPath(C:\ProgramData\LGMOBILEAX\Phone\LGP760.dll)
22:26:54 : _DetachDLL Call
22:26:54 : _DetachDLL Call End
22:26:54 : Call fn_StartUpgrade
The tool didn't find your phone..
Code:
22:26:25 : _IsConnectedPhone([B]0[/B])
22:26:25 : [B]0 - NotConnected[/B].
22:26:25 : 1 - Normal connect success
22:26:25 : 2 - Emergency connect success
LG Mobile support tool is the easiest way..
You should download the last kdz for your IMEI (the version that the tool can find) and place it in:
"C:\shttps\www\swdata\WDLSW\LGP760\XXXXXX\VX0x_00\VX0x_00.kdz" and set the http port to 80.
(Replace Xs with your kdz info, you can grab them from the kdz link).
You should put only one of the two lines in the hosts file, I don't remember whick one but you can try..
LG Mobile Support Tool will connect to the internet but it will "download" the kdz from your PC, it will be very fast.
Sorry for my englesh
Okay, I'm not sure if I'm still doing what I'm supposed to:
To which version of the LG tool are you referring? The original one? The original one in combination with the fake KDZ server?
The folder you are referring to doesn't seem to exist.
Whats with the port? I never set any port before in the KDZ procedures...
Otherwise, I think I get what you mean with the path:
WDLSW/LGP760/ADEUBK/V20b_00/V20B_00.kdz
This file I am already downloading in a DL manager for some time now... (should be finished in 2h )
Next problem: I just tried to go through the regular update (without any offline tricks). It now asks for S/N and IMEI data (which I happily provide). Then update stops immediately:
Updating is not possible any longer due to a fatal
error while the LG Mobile Phone Software Update
Click to expand...
Click to collapse
This is the tutorial with the http server: http://forum.xda-developers.com/showthread.php?p=36351786
If that procedure doesn't work, follow my previous post
Sorry but flashing boot.img will get you nowhere, system partition has been overwritten by cm, best you'll get is bootloop.
I don't know if lg intentionally broke sw mode in JB or why it doesn't work but that's why your phone isn't being detected by lg tool or kdz flasher and you won't be able to fix security error with plain adb.
to dump:
adb shell su -c busybox dd if=/dev/block/mmcblk0p2 of=/sdcard/external_sd/p2.bin
adb shell su -c busybox dd if=/dev/block/mmcblk0p1 of=/sdcard/external_sd/p1.bin
to restore
fastboot flash x-loader p1.bin
fastboot flash u-boot p2.bin
after that software mode will work and your phone should be detected by either lg tool or kdz flasher
@Lelus: You seem to be right... It looked so promising, but indeed, both following the instructions from the GUIDE and the workaround sguerrini97 posted, something always fails...
@sguerrini97: You already helped me sooo much, but do you think you could create those dumps for me? I'm kinda lost here :crying:
Now I've got the PACMAN rom, x-loader and u-boot are the ones from JB, I don't know if they will work..
sguerrini97 said:
Now I've got the PACMAN rom, x-loader and u-boot are the ones from JB, I don't know if they will work..
Click to expand...
Click to collapse
I'm not sure, either... this is mostly new to me, and I know just as much as I learned today (which is already a lot ).
Theoretically you could use xloader and uboot from ics of p765 or p768
Two questions:
Where could I look for people that could help me?
Why is my CWM backup I made from my ICS install (after root, before flashing cm 10.1) not helping?
I have the following files:
Code:
.android_secure.vfat.dup
boot.img
cache.ext4.dup
data.ext4.dup
nandroid.md5
recovery.img
system.ext4.dup
Is system.ext4.dup not what we are looking for? (.dup = dump?), system = x-image? Most of these files are pretty small, though...
You need a backup in .tar format to restore it from adb, you made it in the new CWM format and I don't know if it's possible to restore it from adb. Maybe if you flash my x-loader and my u-boot you will have unlocked bootloader to flash a real recovery to restore it.
sguerrini97 said:
You need a backup in .tar format to restore it from adb, you made it in the new CWM format and I don't know if it's possible to restore it from adb. Maybe if you flash my x-loader and my u-boot you will have unlocked bootloader to flash a real recovery to restore it.
Click to expand...
Click to collapse
You mean your current JB x-loader / u-boot, right? I'm willing to try, could you upload those files?
x-loader: https://dl.dropbox.com/u/95188513/Android/JB/x-loader.img
u-boot: https://dl.dropbox.com/u/95188513/Android/JB/u-boot.img
CWM recovery: http://download2.clockworkmod.com/recoveries/recovery-clockwork-6.0.2.9-p760.img
You have to flash everything from fastboot:
Code:
fastboot flash x-loader x-loader.img
fastboot flash u-boot u-boot.img
fastboot flash recovery recovery-clockwork-6.0.2.9-p760.img
Then try to enter in recovery with [vol+] + [home] + [power], you should be into CWM.
Hi!
My main aim is to root a china phone (symphony w67).
I made the scatter file, rom and stuffs. Now the problem I end up with is when I want to make the cwm recovery image using the Mtk Droid Tools. Here is the log:
--------------------------------------------------------------------------------------------------------------------------------------
--->>> Connect to device <<<--- --- The preservation folder on the computer: C:\Users\Adib\Desktop\MtkDroidTools v2.5.3\backups\W67_140811_ForFlashtoolFromReadBack _141029-124724\ --- scatter is write to the file:
C:\Users\Adib\Desktop\MtkDroidTools v2.5.3\backups\W67_140811_ForFlashtoolFromReadBack _141029-124724\MT6572_Android_scatter.txtcopying is complete
-- preloader.bin ...it is copied ... cut OK
-- MBR ...it is copied
-- EBR1 ...it is copied
-- pro_info ...it is copied
-- nvram.bin ...it is copied
-- protect_f ...it is copied
-- protect_s ...it is copied
-- seccfg ...it is copied
-- uboot.bin ...it is copied
-- boot.img ...it is copied
--- ERROR :No find KernelGZ
--- ERROR :No Split Boot Image
-- recovery.img ...it is copied
-- secro.img ...it is copied
-- misc ...it is copied
-- logo.bin ...it is copied
-- expdb ...it is copied
-- system.img ...it is copied
--- task is complete ---
------------------------------------------------------------------------------------------------------------------------------------------------
As u can see there are 2 errors:
--- ERROR :No find KernelGZ
--- ERROR :No Split Boot Image
and also no modified cwm recovery image is created in the backup folder. So may I please have some solution for this error? I became very desperate, been trying to root this device for 4 days.
Below are more details about the mobile if it helps in anyway:
Model number: W67
Android version: 4.4.2
Baseband version: MOLY.WR8.W1315.MD,WG.MP.V43, 2014/05/22 18:56
Kernel version: 3.4.67
Build number: W67_1_XXX_V01.0_V2.0_20140809
brother,,,
How to Root Symphony W67
i got the same error, maybe locked bootloader
Same error with a Mediatek D101_MB_V4
Android 4.4.2
Rocky oo7 said:
How to Root Symphony W67
Click to expand...
Click to collapse
Message me rocky, I can root w67
Adib254 said:
Hi!
My main aim is to root a china phone (symphony w67).
I made the scatter file, rom and stuffs. Now the problem I end up with is when I want to make the cwm recovery image using the Mtk Droid Tools. Here is the log:
--------------------------------------------------------------------------------------------------------------------------------------
--->>> Connect to device <<<--- --- The preservation folder on the computer: C:\Users\Adib\Desktop\MtkDroidTools v2.5.3\backups\W67_140811_ForFlashtoolFromReadBack _141029-124724\ --- scatter is write to the file:
C:\Users\Adib\Desktop\MtkDroidTools v2.5.3\backups\W67_140811_ForFlashtoolFromReadBack _141029-124724\MT6572_Android_scatter.txtcopying is complete
-- preloader.bin ...it is copied ... cut OK
-- MBR ...it is copied
-- EBR1 ...it is copied
-- pro_info ...it is copied
-- nvram.bin ...it is copied
-- protect_f ...it is copied
-- protect_s ...it is copied
-- seccfg ...it is copied
-- uboot.bin ...it is copied
-- boot.img ...it is copied
--- ERROR :No find KernelGZ
--- ERROR :No Split Boot Image
-- recovery.img ...it is copied
-- secro.img ...it is copied
-- misc ...it is copied
-- logo.bin ...it is copied
-- expdb ...it is copied
-- system.img ...it is copied
--- task is complete ---
------------------------------------------------------------------------------------------------------------------------------------------------
As u can see there are 2 errors:
--- ERROR :No find KernelGZ
--- ERROR :No Split Boot Image
and also no modified cwm recovery image is created in the backup folder. So may I please have some solution for this error? I became very desperate, been trying to root this device for 4 days.
Below are more details about the mobile if it helps in anyway:
Model number: W67
Android version: 4.4.2
Baseband version: MOLY.WR8.W1315.MD,WG.MP.V43, 2014/05/22 18:56
Kernel version: 3.4.67
Build number: W67_1_XXX_V01.0_V2.0_20140809
Click to expand...
Click to collapse
I have same problem
help with rooting and making cwm mtk6572
my phone is o+8.93 mtk6572 and was following this thread http://forum.xda-developers.com/showthread.php?t=2519432&page=2
but see this image here when using 1st step of droid root tool : i cant make scatter file why is this?
any help is much appreciated. i've been searching for rooting methods for a week a now
How To Fix WiFi NVRAM WARNING SS
Watch The Procedure Video : https://youtu.be/Cp7hmHO76FA
Step 1 : Download Root Explorer App
Step 2 : Download WiFi Fix Files [Attached Files]
Step 3 : Copy the wifi fix files as WiFi and WiFi_Custom from SD Card.
Step 4 : Paste these files in following root directory data/nvram/APCFG/APRDEB/ and paste it here overwrite the file yes .
Step 5 : click on WiFi then permissions owner and group tick read write rest untick check the images below for better understanding.
Step 6 : Do same with WiFi_Customs permissions owner and group tick read write rest untick.
Step 7 : Reboot smartphone.
How To Fix Invalid IMEI [MTK Devices 5.0] SS
Watch The Procedure Video
Step 1 : Open the software then type your smartphone SN number
Step 2 : Type IMEI1 & IMEI2
Step 3 : Click On MP0B_001 it will generate the MP0B_001 file
Step 4 : Copy that MP0B_001 file in SD Card then open Root Explorer App then DATA/NVRAM/MD/NVD_IMEI paste the file here yes overwrite it.
Step 5 : Restart the smartphone..
Hello. I have a ZTE Blade L2
I made nvram backup, but... when I flashed LineageOS and restore backup....
Files are right, but, user (and group) nvram doesn't exist.
So, file WIFI is not nvram:nvram owner, but root:root.
What can I do?
Thank you.
How to flash non-8297W CPB roms (roms for Himax and Micromax phones) with YGDP tool
1) Open YGDP (password:369) choose the phone model
2) Choose downloaded rom in CPB format from your hard drive.
3) Go on as usual with YGDP and let it unzip the CPB
4) When it finishes go to the root of your C drive, where the YGDP folder is and go to the folder DownFiles that it created. There are the contents of the CPB
Look for the file ''phone.info'' (there are 2 of them)
5) Open one with notepad++ and find a line that says ''ProductName=8297**'' (** will be different according to the cpb's origin. If for example the cpb is from India it will be
ProductName=8297W_I01. You now have to delete ''_I01'' so that it only reads ProductName=8297W. You get the logic. You change this to whatever your phone's real code name is. If you have a Micromax phone, you add ''_S10'' ( 8297W_S10 )
6) Now that you made the change save the file and do the same with the other phone.info file
7) Next find the file YL-params.bin.
open with notepad and find the line that says ''1.01.000.P1.8297W_I01'' (or something very similar, you will see it, there are not many lines in this file)
Do the same as before, modify the ''**'' to match your phone's code, exactly like you did with phone.info ( 8297W_S10 )
8) Save the File
9) Ready. Go on with the installation on YGDP as normal.
Credits:
Coolpad
Anggriawan
Yuusuv
Borsosg
Korekore1
Mixanikosgr
Modaco members
Me ( Greegor )
HIT THANKS BUTTON IF U FOUND THIS POST HELPFUL :good:
What is td
Greegor1995 said:
How to flash non-8297W CPB roms (roms for TD phone, Himax and Micromax phones) with YGDP tool
1) Open YGDP (password:369) choose the phone model (If you have TD rom , choose 8297, for Hymax and Micromax phones, select the correct model code)
2) Choose downloaded rom in CPB format from your hard drive.
3) Go on as usual with YGDP and let it unzip the CPB
4) When it finishes go to the root of your C drive, where the YGDP folder is and go to the folder DownFiles that it created. There are the contents of the CPB
Look for the file ''phone.info'' (there are 2 of them)
5) Open one with notepad++ and find a line that says ''ProductName=8297**'' (** will be different according to the cpb's origin. If for example the cpb is from India it will be
ProductName=8297W_I01. You now have to delete ''_I01'' so that it only reads ProductName=8297W. You get the logic. You change this to whatever your phone's real code name is. If you have a Micromax phone, you add ''_S10'' ( 8297W_S10 )
6) Now that you made the change save the file and do the same with the other phone.info file
7) Next find the file YL-params.bin.
open with notepad and find the line that says ''1.01.000.P1.8297W_I01'' (or something very similar, you will see it, there are not many lines in this file)
Do the same as before, modify the ''**'' to match your phone's code, exactly like you did with phone.info ( 8297W_S10 )
8) Save the File
9) Ready. Go on with the installation on YGDP as normal.
Credits:
Coolpad
Anggriawan
Yuusuv
Borsosg
Korekore1
Mixanikosgr
Modaco members
Me ( Greegor )
Hit Thanks Button if u found this post helpful
Click to expand...
Click to collapse
Good Job Mate @Greegor1995 ,This Thread is Added To the INDEX ..
Jainanjay said:
What is td
Click to expand...
Click to collapse
Sometimes while flashing stock rom using ygdp tool , the process gets stucked at 98% .
This thread helps in overcoming this issue
LoverBoy2415 said:
Good Job Mate @Greegor1995 ,This Thread is Added To the INDEX ..
Click to expand...
Click to collapse
Thankz brother
Greegor1995 said:
Thankz brother
Click to expand...
Click to collapse
..No Mentions Bro
I am using a custom rom can i go back to stock by using this method. Please reply
SabirMon said:
I am using a custom rom can i go back to stock by using this method. Please reply
Click to expand...
Click to collapse
Yes, you can.
Thanks
I have made changes to porduct name and YL params.bin file,flashing is done with YGDP 3.98,
Kindly help to fix this
14:55:58 CELL0: Software Version: Assembly - <V3.98_141222_02>
14:55:58 CELL0: Cell 0 USB address is: com3
14:55:58 CELL0: Start Download.
14:55:58 CELL0: Download Started...
14:55:58 CELL0: Downloading CPB:
14:55:58 CELL0: Init Connect Arg.
14:55:58 CELL0: Downlaod DA Start.
14:56:01 CELL0: Downlaod DA Success.
14:56:01 CELL0: Verify is Partition be Changed.
14:56:01 CELL0: Partition is Changed.
14:56:01 CELL0: Get Usb Status Success.
14:56:01 CELL0: Read YL-Parames Partition Start.
14:56:07 CELL0: Read YL-Parames Partition Success.
14:56:07 CELL0: Check between YL-Parames Partition and PhoneInfo Start.
14:56:07 CELL0: Check between YL-Parames Partition and PhoneInfo Success.
14:56:07 CELL0: Init BackUp Table.
14:56:07 CELL0: Read BackUp File Start.
14:56:44 CELL0: Read BackUp File Success.
14:56:44 CELL0: Mach Storage Type is Successful.
14:56:44 CELL0: startAddr 5f000000, format length 34b300000
14:56:51 CELL0: Format Device Success.
14:56:51 CELL0: Start Download CPB.
14:59:31 CELL0: Download CPB Failed.
14:59:31 CELL0: ERROR:1041
14:59:31 CELL0: DisConnect.
14:59:51 CELL0: Total download time elapsed: 3 min : 53 sec
14:59:51 CELL0: Downloading CPB: Failed!
How did you solved it
Greegor1995 said:
Sometimes while flashing stock rom using ygdp tool , the process gets stucked at 98% .
This thread helps in overcoming this issue
Click to expand...
Click to collapse
i am stuck at 88% on micromax a311 . can you please help me
Same problem with micromax A310. Ygdp gets struck at 98%. And then cpb file download failed. Tried this solution but no results. Went to a Mobile repair store. He was not able to resolve the problem. Pls. If possible make a YouTube video of whole this procedure. It will be helpful
Required :
- Driver Qualcomm for Windows
- QPST_2.7.422.zip
- Driver ADB Installer
- Modem Lenovo A6000/A6000+ include ADB fastboot
- Extrac Modem in drive C:\adb and open the folder
** Edit file qcn use HxD change IMEI and Convert IMEI
SIM 1
Sector 343 Offset 0002AE50 point 00-08
Change 08 8A 76 21 04 22 57 85 45 adjust to you IMEI-1
SIM 2
Sector 188 Offset 000178E0 point 00-08
Change 08 8A 76 21 04 22 57 85 26 adjust to you IMEI-2
** Step change IMEI :
1. Open Convert IMEI
2. Write you IMEI-1 and klik Convert
3. Open HxD
4. Press Ctrl + F write/copas 08 8A 76 21 04 22 57 85 45 Datatype Hex-values Direction All - Ok
5. Replace it with IMEI-1 numbers convert results
6. Write you IMEI-2 and klik Convert
7. Open HxD
8. Press Ctrl + F write/copas 08 8A 76 21 04 22 57 85 26 Datatype Hex-values Direction All - Ok
9. Replace it with IMEI-2 numbers convert results
10. Close HxD and save file qcn
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
** For those who use stock rom not need root can be directly executed steps :
1. Install driver qualcomm, qpst, adb installer
2. Open the folder C:\adb
3. Press and hold down the Shift + Right Click - Open command windows here
4. Sign in fastboot mode button (vol- & power) and type :
fastboot erase modem (enter)
fastboot erase modemst1 (enter)
fastboot erase modemst2 (enter)
fastboot flash modem NON-HLOS.bin (enter)
fastboot flash modem modemst1.bin (enter)
fastboot flash modem modemst2.bin (enter)
5. Turn off the phone remove the battery
6. Sign test mode button (vol+ & Power)
7. Open QPST software download
8. Tab Restore
9. Browse PORT Qualcomm Diag
10. If you already connect, browse file QCN
11. Select the edited file QCN use hex editor
12. Tick Allow phone/file ESN mismatch
13. Start (wait for the process)
14. Reboot phone
15. Check the IMEI
16. Check signal SIM-1 the WCDMA/LTE only
17. Finished :laugh:
** For those who use custom rom / are not able to enter the test mode must root stock rom steps:
1. Root
2. Open SuperSU settings default access to Grant
3. Turn off the phone
4. Proceed to step 1 to 5
5. Turn on the phone
6. Install Terminalemulator.apk
7. Open terminalemulator type su (enter)
8. Type setprop sys.usb.config diag, adb (enter)
9. Continue to restore files qcn step 7 to finish
Special thanks :
- Allah SWT.
- Carlos Spitzer
- fawazahmed0
- Robby Primarizal
- Hanif Nurul Huda
- Amri Gadroen
- All member (OFFICIAL INDONESIA) LENOVO A6000 INA
@zround - Just in case, you are feeling low due to no response from anyone. Brother, what you did was a much much needed thing, as many of the A6000 users are having IMEI problems on flashing custom ROMs. This thread is definitely a life saver for the guy having IMEI issue.
Sometimes, you don't get much appreciation from others in the beginning (has happened with me), but that doesn't mean you stop doing so.
So, all I wanna say is "thanks" and I really appreciate what you did.
:silly:
sasukay said:
@zround - Just in case, you are feeling low due to no response from anyone. Brother, what you did was a much much needed thing, as many of the A6000 users are having IMEI problems on flashing custom ROMs. This thread is definitely a life saver for the guy having IMEI issue.
Sometimes, you don't get much appreciation from others in the beginning (has happened with me), but that doesn't mean you stop doing so.
So, all I wanna say is "thanks" and I really appreciate what you did.
:silly:
Click to expand...
Click to collapse
@sasukay if there is no response means i think they managed to restore IMEI Lenovo A6000/+ in my way, :angel: i'm not proud of the appreciation and responses but can share and help others who seemed to me it was really fun.
let's drink a cup of coffee so as not to panic
zround said:
@sasukay if there is no response means i think they managed to restore IMEI Lenovo A6000/+ in my way, :angel: i'm not proud of the appreciation and responses but can share and help others who seemed to me it was really fun.
let's drink a cup of coffee so as not to panic
Click to expand...
Click to collapse
Hehhehhe.....I was just being dramatic... :silly:
hi sir,
i have lenovo a 6000.problem both imei null .when i try to write the qcn from ur guide.but in ur 9th step when i select the diag phone it shows no phone connected in qpst window.any solution please.
rajendrakumar said:
hi sir,
i have lenovo a 6000.problem both imei null .when i try to write the qcn from ur guide.but in ur 9th step when i select the diag phone it shows no phone connected in qpst window.any solution please.
Click to expand...
Click to collapse
if you use a stock rom then how to enable diag port android to turn off the device to unplug the battery and then press and hold the button (vol + & power) until the entrance test mode and plug the USB cable
or
by turning on the device (root) pairs terminalemulator.apk open to write:
su
setprop sys.usb.config diag, adb
restore qcn :good:
This saved my life thank you so much. Love from philippines bro
Unable to mount /modem
Bro.. ini udah ikutin sampe step 5, lalu pas gua nyalain malah stuck di logo booting. Coba clear cache via TWRP ada tulisan "Unable to mount /modem". Kira2 itu knp ya ? hehehe masih noob
waw steady
LYudhistira said:
Bro.. ini udah ikutin sampe step 5, lalu pas gua nyalain malah stuck di logo booting. Coba clear cache via TWRP ada tulisan "Unable to mount /modem". Kira2 itu knp ya ? hehehe masih noob
Click to expand...
Click to collapse
Step :
Masuk fastboot dan erase semua partisi, (boot, userdata, cache, system, modem, modemst1, modemst2)
Flash stock rom Lollipop via qfil qpst atau qualcomm downloader
Root
Masuk fastboot dan eksekusi
fastboot erase modem
fastboot erase modemst1
fastboot erase modemst2
fastboot flash modem NON-HLOS.bin
fastboot flash modem modemst1.bin
fastboot flash modem modemst2.bin
Restore qcn
Hello, my imei's are good but error in network (cannot connect to selected network ) after writing qcn (without editing ) only SIM 1 worked with network but sim 2 not working > but after editing with my imei's no network .. any suggestions i need booth sims to work!?
Sobaro said:
Hello, my imei's are good but error in network (cannot connect to selected network ) after writing qcn (without editing ) only SIM 1 worked with network but sim 2 not working > but after editing with my imei's no network .. any suggestions i need booth sims to work!?
Click to expand...
Click to collapse
- That's because the modem partition problem,
- try
fastboot erase modem
fastboot erase modemst1
fastboot erase modemst2
fastboot flash modem NON-HLOS.bin
fastboot flash modem modemst1.bin
fastboot flash modem modemst2.bin
- after that restore qcn already in the edit imei previous,
if still not successful,
then delete all partitions (boot, splash, userdata, cache, system) via fastboot, and then flash a stock rom via qfil or qualcomm downloader continued upgrading to latest stock rom, then restore qcn.
thanx that worked for me , now i get the two sims to work like a charm but still second imei is showing null !! i have no problem as long as sims are working but it is good if some one give a reason! thanx in advance
wrongly restored efs,modem... partitions from a lenovo a6000+ to another a6000
wrongly restored efs,modem... partitions (using TWRP) from a lenovo a6000+ to another a6000
i have no backups of the corresponding partitions of this phone
now phone showing imei null and sim detection errors also ui getting unstable and services are unstable in stock rom (most times) when flashed using qualcomm downloader & bootloops in other some custom roms.
fastboot,recovery etc of the phone is perfectly working.
when i did writing the altered qcn (with corresponding imei) via qpst i got just errors.
can anyone help me troubleshoot this ??
https://drive.google.com/file/d/0BwFcGoIexiPed210VXdnY2xUYU0/view?usp=sharing
zround said:
Required :
- Driver Qualcomm for Windows
- QPST_2.7.422.zip
- Driver ADB Installer
- Modem Lenovo A6000/A6000+ include ADB fastboot
- Extrac Modem in drive C:\adb and open the folder
** Edit file qcn use HxD change IMEI and Convert IMEI
SIM 1
Sector 343 Offset 0002AE50 point 00-08
Change 08 8A 76 21 04 22 57 85 45 adjust to you IMEI-1
SIM 2
Sector 188 Offset 000178E0 point 00-08
Change 08 8A 76 21 04 22 57 85 26 adjust to you IMEI-2
** Step change IMEI :
1. Open Convert IMEI
2. Write you IMEI-1 and klik Convert
3. Open HxD
4. Press Ctrl + F write/copas 08 8A 76 21 04 22 57 85 45 Datatype Hex-values Direction All - Ok
5. Replace it with IMEI-1 numbers convert results
6. Write you IMEI-2 and klik Convert
7. Open HxD
8. Press Ctrl + F write/copas 08 8A 76 21 04 22 57 85 26 Datatype Hex-values Direction All - Ok
9. Replace it with IMEI-2 numbers convert results
10. Close HxD and save file qcn
** For those who use stock rom not need root can be directly executed steps :
1. Install driver qualcomm, qpst, adb installer
2. Open the folder C:\adb
3. Press and hold down the Shift + Right Click - Open command windows here
4. Sign in fastboot mode button (vol- & power) and type :
fastboot erase modem (enter)
fastboot erase modemst1 (enter)
fastboot erase modemst2 (enter)
fastboot flash modem NON-HLOS.bin (enter)
fastboot flash modem modemst1.bin (enter)
fastboot flash modem modemst2.bin (enter)
5. Turn off the phone remove the battery
6. Sign test mode button (vol+ & Power)
7. Open QPST software download
8. Tab Restore
9. Browse PORT Qualcomm Diag
10. If you already connect, browse file QCN
11. Select the edited file QCN use hex editor
12. Tick Allow phone/file ESN mismatch
13. Start (wait for the process)
14. Reboot phone
15. Check the IMEI
16. Check signal SIM-1 the WCDMA/LTE only
17. Finished :laugh:
** For those who use custom rom / are not able to enter the test mode must root stock rom steps:
1. Root
2. Open SuperSU settings default access to Grant
3. Turn off the phone
4. Proceed to step 1 to 5
5. Turn on the phone
6. Install Terminalemulator.apk
7. Open terminalemulator type su (enter)
8. Type setprop sys.usb.config diag, adb (enter)
9. Continue to restore files qcn step 7 to finish
Special thanks :
- Allah SWT.
- Carlos Spitzer
- fawazahmed0
- Robby Primarizal
- Hanif Nurul Huda
- Amri Gadroen
- All member (OFFICIAL INDONESIA) LENOVO A6000 INA
Click to expand...
Click to collapse
Using Window 10, I'm not able to perform 1s step) Shift + click anywhere in folder, I think driver is not supported
2) not able to install terminal emulator bcz unknown source blocked and not working .
I edited the QCN file but unable to move forward from first step,
What should I do,
No communiction device , no imei, no bluetootgh, no wifi.
Should I use windows 7? Also how to install terminal apk if unknown source is not getting enabled for security purpose? Can I perform these steps on MM custom roms?
zround said:
Step :
Masuk fastboot dan erase semua partisi, (boot, userdata, cache, system, modem, modemst1, modemst2)
Flash stock rom Lollipop via qfil qpst atau qualcomm downloader
Root
Masuk fastboot dan eksekusi
fastboot erase modem
fastboot erase modemst1
fastboot erase modemst2
fastboot flash modem NON-HLOS.bin
fastboot flash modem modemst1.bin
fastboot flash modem modemst2.bin
Restore qcn
Click to expand...
Click to collapse
Bro ganteng...
Abis ngikutin langkah tersebut di atas
Ane malah got Baseband: Unknown
Panik...
Trust flash page Downloaded yg Ada do ....kitkat_ROW.zip
baseband balik...
Imei Null
Trus Masukin imei pake program imei writter
Jadi
Normal
Tapi "tetep no service"
What's should I do ya Gan?
Any other method Kali Gan...
BTW... Makasih banyak udah menginspirasi
rifky said:
Bro ganteng...
Abis ngikutin langkah tersebut di atas
Ane malah got Baseband: Unknown
Panik...
Trust flash page Downloaded yg Ada do ....kitkat_ROW.zip
baseband balik...
Imei Null
Trus Masukin imei pake program imei writter
Jadi
Normal
Tapi "tetep no service"
What's should I do ya Gan?
Any other method Kali Gan...
BTW... Makasih banyak udah menginspirasi
Click to expand...
Click to collapse
Lollipop only om bosku, :laugh:
pankajy said:
Using Window 10, I'm not able to perform 1s step) Shift + click anywhere in folder, I think driver is not supported
2) not able to install terminal emulator bcz unknown source blocked and not working .
I edited the QCN file but unable to move forward from first step,
What should I do,
No communiction device , no imei, no bluetootgh, no wifi.
Should I use windows 7? Also how to install terminal apk if unknown source is not getting enabled for security purpose? Can I perform these steps on MM custom roms?
Click to expand...
Click to collapse
Try opening of adb cmd wear this in windows 10
- Flash stock rom lollipop
- Then follow these instructions
If you still can not, then tried to use windows 7 because I put windows 7 when executed
zround said:
Lollipop only om bosku, :laugh:
Click to expand...
Click to collapse
thanks...
AWALE PANCEN LOLLIPOP Gan
it is lollipop lho...
i decide to flash KITKAT because, the BaseBand Unknown show up after trying flash it back with lollipop Bro...
ngono lho
but finally it is back to lollipop again now, of course with All time "No Service" message
yesterday... i try to do all those wonderfull steps of yours again...
but alhamdulillaah... i have no luck... yet
actually... what is the lolllipop version of the phone should be to do those step you wrote
because i did it with my A6000 using the latest lollipop 5.0.2 / Kraft-A6000_S061_100727, is it matter? (singing Nothing Else Matters)
and would you please checkput my attachment please, did you see anything wrong there?
btw, where did you get those modem, modemst1, modemst2 & non-hlos bin files from? would you mind share it with us
always thanks in advanced
Sobaro said:
thanx that worked for me , now i get the two sims to work like a charm but still second imei is showing null !! i have no problem as long as sims are working but it is good if some one give a reason! thanx in advance
Click to expand...
Click to collapse
really? you did it?
so glad to know that :good:
congrat man
would you please tell me what version of firmware do you have?
mine is like in the attachment
Thanks in advance