I have a i605 with Verizon. It's rooted and I've been running Jellybeans 22 (4.1) since August. Saturday I decided to install the new 4.4 with CyanogenMod 11 which just came out. I goofed and installed the 7100 copy (I think it was 7100, started with a 7). I got a no service message which makes sense. Ok Mark, what's next dumbass? lol so I got the right version and installed it, and still didn't get service. So then I rolled it back to the image I made before I started this whole thing and still no service? I read other postings and checked for phone number and IMEI which are populated. ERI version is 5. I also keep getting a message asking me to go to a GLOBAL setting which doesn't help either. I tried pulling the SIMS card and rebooting. The instructions said to put the card back in while rebooted but the power supply blocks that. Soo.... do I try to get my stock installed or is there other things I can try.. There's this cute chick who likes me and if I can't text her I might never get laid!!!! (I wish )
I also had the same problem of baseband and imei showing unknown but I was able to fix it.
thanks,
chat/email : [email protected]
Should I unroot
Should I unroot the phone and go back to stock to see if it corrects the issue? Will I need to accept an OTA?
Use cwm.
Sent from my SCH-I605 using Tapatalk 2
I would do what hopesrequiem suggested. If you are using TWRP to flash CM11 you wont have data. You have to use CWM 6.0.4.3 for some odd reason.
DX.Deception said:
I would do what hopesrequiem suggested. If you are using TWRP to flash CM11 you wont have data. You have to use CWM 6.0.4.3 for some odd reason.
Click to expand...
Click to collapse
what Went South was I couldn't make phone calls or text. Even after restoring 4.1 Rom. I didn't have issue with data. But to answer my own question. . I fixed my issue by restoring my stock Image and then used setup / backup / factory reset. That did it. When I restored 4.1 it was working again. Thanks for the info on cwm version.
Well im glad all is well now!
Help!
Hello! Need help!
The problem is this .. darkforvard 4.1 firmware was decided to try the new Android and flashed jungle extreme 4.3 firmware ..
good but a little bit not mine .. while rolling back its 4.1 flew on imei 00000049 ... and the serial number on 00000 .... EFS apparently not kept ... result
does not work and an Internet connection ..
If anyone actually encountered such a problem please tell me how to get out of this situation?
theory of course is good but need a practical personal experience ! If you can write about the points and what to do
Currently in the phone
Firmware version N7100XXDME4
Build number JZO54K.N7100XXDMG1
Rekaveri philz_touch_5.15.0-n7100
Thank you!
My Galaxy S3 GT-I9305 LTE was running Liquid Smooth 2.37. Recently I lost notification and phone ring sounds and now I have lost baseband and I have no cell signal.
In the phone's 'about' section the baseband field is empty. Android version showing is 4.3.
I'm not quite sure what I did wrong, first to try and get back the sounds and then baseband, I have been playing around with various custom and stock ROMS and kernals to get full functionality back.
I've read tons of help posts but nothing works.
Here's a few of the things I've tried with results in brackets, used CWM recovery to restore working backup (failed 'unsupported file' message),
reflashed kernals (neither Boeffla nor yank555 have worked, wipe/data restore in CWM (it still takes me back to 4.3 with no baseband).
I thought I'd re-flash back to the phone's original stock ROM using Kies, but the weird thing is Kies doesn't restore, it upgrades to the latest 4.3 ROM which fails to restore baseband.
I wanted to send the phone back to the 4.1.2 it came with or was it an earlier ROM? I can't remember as I didn't note it down, I bought the phone second hand, it arrived loaded with a stock ROM for Australia's Optus network. I promptly rooted and flashed the phone to Liquid Smooth and the phone ran fine for months on the 2 Degrees Network in New Zealand.
Anyway, I must have tried reflashing a dozen stock roms I've found online using Odin. Some of them partially work, I get sound back, (it seems only the 4.3 ones work, with the german I9305XXUEMKC reliably loading - it even gives me a NZ english install option) but don't restore the baseband
. All the ones I've found for Optus are rejected, I get the 'unsupported device' or status 7 error in Odin.
So I decided to flash one that works, install cwm, root the phone and try installing different baseband kernals to fix the (probably corrupt) efs.
But I'm going round in circles trying to root the phone. Using CWM, supersu shows as successfully installed, but when I boot into the OS root checker shows my phone is not rooted. Knox seems to obstruct every attempt I make to disable it as well. I keep getting these 'knox stopped etc...from working messages'.
I'm sorry if my description is a bit confusing, I'm happy to clarify anything.
I'm at my wits end. I want to try everything before I have to ship the phone off to a repairer who may charge me hundreds of dollars to fix the phone.
This is I9300 not I9305 Q&A
Use the report button and ask a mod to move to the correct forum .
I can offer no help as i fail to understand the post .
As said before you are in wrong place and are not giving us a clear question to answer. If its a root problem there are fixes for it. Status 7 error is discussed in many threads. Flashing MG4 modem fixes efs problem. Downgrading causes problem. Learn to search before making a thread.
Alright guys, this is gonna be kinda long so get ready. I was running stock 4.4.2 NEW and I saw that there was a way to get GPE 4.4.3 and 4.4.4 rom working on the s4. I followed all the instructions on RickGrimes's post and wifi didn't work. Not and big deal. I couldn't soft reboot, so I tried flashing gogolies nc2 wifi fix and this modem worked. I then tried to update to 4.4.4, also following the instructions and the wifi didn't work once again. I flashed gogolies nc2 wifi fix again but it did not work. I also realized that I had no service at all and that I couldn't send or receive any messages or calls. So I did the safe thing and used Odin to get back to stock. I am currently running stock but the service is still terrible in places where I usually get great signal. Also, my wifi strength seemed to go down from what it usually is. Another issue is that my contacts that were backed up in backup assistant aren't there anymore at all. I generally know what I'm doing when it comes to this stuff but for some reason I have no idea how to resolve these issues. Any help will be appreciated.
Reolved
Jessooca said:
The easiest way to fix your phone or any phone for this matter is always to download and flash the stock tar file of whatever version of Android you were last on in Odin.
Then visit towelroot.com in your browser on your phone and root it again. (Don't forget to enable usb debugging first)
Click to expand...
Click to collapse
I wound up going back to stock 4.4.2 via Odin, but the problem still persisted. I figured out the my network settings were changed to Global instead of CDMa/LTE. Changed it back and all is well! Thank you though!
Ok, i'm fairly new to this stuff but have successfully rooted and modified several of my devices over the years. I've been attempting to upgrade my vs985 to as close to stock 5.1.1 as i can and after much reading decided on jasmine. I was rooted on kk 4.4.2 12b and I had no problems. the main reason i wanted to upgrade was for compatibility with my android play car stereo. I didn't have twrp so first i downloaded flashify and quickboot then flashed twrp from flashify. All good so far. Next I downloaded jasmine 9.0 and 9.1 or at least i thought lol. As it so happened i mistakenly ended up with one of the files being just the kernel for 5.1.1 35b. Must of been a long day cause I mistakenly failed to backup my current system and proceeded wipe data, cache, dalvik, and flashed the kernel file. As you might imagine it didn't turn out very good. I was stuck in boot loop. Fortunately I could still get into download mode so I was able to use the lg flash tool and I brought it all the way back to 10b stock firmware. Then i grabbed stump and rooted and flashed twrp again. at some point i noticed my cell signal was all over the place, up, down , no signal and it roamed almost constantly if there was any signal. I've had this phone and service for well over a year and never had anything like this at all. I knew it was something I did. I checked the back cover to be sure it was on properly and had good connection with the antenna and all checked out. I decided to go ahead and do the upgrade to jasmine 9.1 hoping this would correct the issue. Well no dice. I did create a backup this time and proceeded to wipe everything and flash 9.0 reboot then wipe nothing and flash 9.1, i guess as you call it "dirty" then reboot again. Here is a link to where i got the zips and instructions
http://forum.xda-developers.com/showpost.php?p=63305722&postcount=4842
in the instructions it says "RESET factory from within ROM (in Settings) - REQUIRED" . this step seemed strange as why would i do a factory reset on my device and erase everything i just did? would it not return it to original? I wasn't even sure if that was what he meant so i skipped that. After all was finished my signal was still all over the place could hardly make a call. it was bad. So once again I used lg flash tool and returned it to stock 4.4.2 10b, this time I wiped the data, cache, delvik and system. To my complete surprise the signal had not improved, in fact it could have actually been worse. As I said waaaaaay at the top of this post before i started all this i was running 4.4.2 12b, not sure how i ended up with 12b as i don't remember any upgrades after i downgraded to 10b and rooted. I froze the ota's with titanium backup but maybe 12b was pushed before i was able to freeze them. Anyway I couldn't figure out how to get 12b back now so I just flashed the 4.4.2 12b modem instead, This time I wiped cache and delvik before and after the flash then rebooted. This fixed my signal, everything seems normal now. no roaming and good signal. my software build however still shows 10b, but I guess thats correct since I only flashed the modem.
I really want 5.1.1 on my G3 but I need my signal too lol. can any one help me figure out how to get this done, can I flash the 12b modem on 5.1.1 this is where i got the file
http://forum.xda-developers.com/verizon-lg-g3/development/rom-jasminerom-v1-0-t2904641 it is way down the bottom of the page. Sorry for the extremely long post i just wanted to make sure i didn't leave any details out.
Any help would be greatly appreciated,
thanks in advance
@Allen227
i dont know if jasmine flashes the L modem when you flash it, but if it doesnt, that would be why you are having issues after flashing the rom.
other than that, i dont know what would cause modem issues.
bweN diorD;4132606 [user=7106818 said:
@Allen227[/user]
i dont know if jasmine flashes the L modem when you flash it, but if it doesnt, that would be why you are having issues after flashing the rom.
other than that, i dont know what would cause modem issues.
Click to expand...
Click to collapse
@Allen227
TL;DR but yes, JasmineROM flashes the appropriate modem. v9.0 only flashes the 24B modem because it doesn't contain a fuller set of the necessary partitions to allow the 35B modem to work by simply replacing the 24B modem with the 35B one.
You can flash the 35B bootstack after flashing JasmineROM 9.0 and the 9.1 update, or SkyDragon 6.x, but you must not be on the 35B bootstack before flashing either UNLESS you also flash the 35B bootstack again after flashing the ROM.
For reasons why: http://forum.xda-developers.com/showthread.php?p=64064555
Edit: I meant to add, the 35B boostack contains the 35B modem and everything needed for it to work with JasmineROM 9.0/9.1.
Hi, anybody from bosses ,plz help, sorry for noob querry... using g3 stock rom 4.4.2 and want to upgrade to lollipop and find jasmine ROM most votes. rooted my device with king root and installed twrp 2.8.7.0 recovry. downloaded jasmin ROM9.0, back up my current rom.
can u please guide me steps,
have i too flash kernal before jasmine ROM? or my existing stock kernal will work fine with jasmine 9.1
placed downloaded ROM in my download folder in phone memory [not in sd Card] , when i would boot in recovry in wipe cache delvik etc will it erase this rom and phone data too???
what if something gone rom? in my g3 there is no option of adb , adb does not work on my g3 dont know why.....
if something gone wrong , can i recover phone?
please see attached pics for some clarification...
sorry for,long post, actualy want to be safe ,,, as i am new for these things ..
tAheEr73 said:
Hi, anybody from bosses ,plz help, sorry for noob querry... using g3 stock rom 4.4.2 and want to upgrade to lollipop and find jasmine ROM most votes. rooted my device with king root and installed twrp 2.8.7.0 recovry. downloaded jasmin ROM9.0, back up my current rom.
can u please guide me steps,
have i too flash kernal before jasmine ROM? or my existing stock kernal will work fine with jasmine 9.1
placed downloaded ROM in my download folder in phone memory [not in sd Card] , when i would boot in recovry in wipe cache delvik etc will it erase this rom and phone data too???
what if something gone rom? in my g3 there is no option of adb , adb does not work on my g3 dont know why.....
if something gone wrong , can i recover phone?
please see attached pics for some clarification...
sorry for,long post, actualy want to be safe ,,, as i am new for these things ..
Click to expand...
Click to collapse
In the future, please do not post the same thing in two different threads. This is against XDA's forum rules. Also, no reason to hijack an only partially related thread. I answered you in the JasmineROM thread.
Sorry for rule breaking, actually i did not aware of that. will avoid surely next time and thanks for reply. hats off to you.
Thanks for your help guys. Last night I figured out my phone was allowing me to send and receive text messages and make outgoing calls but was completely unable to receive any calls. Signal still terribly inconsistent, it would be on 4g one minute then you could watch as it dropped then no service. There'd be no service for 3 or 4 minutes then it would repeat that cycle again. If I switch from global to cdma/let in settings it would immediately regain full signal. Then the cycle of it dropping out would start again. I got to looking through about phone in settings and realized my imei number was missing, all zeros. I'm assuming that probably is the root of my problems. Not sure what to do, I doubt Verizon can help. Phones not insured or under warranty anymore. I haven't researched this New development on te forums yet it got to late last night. If anyone knows of this problem I could use your help. Thanks
Allen227 said:
Thanks for your help guys. Last night I figured out my phone was allowing me to send and receive text messages and make outgoing calls but was completely unable to receive any calls. Signal still terribly inconsistent, it would be on 4g one minute then you could watch as it dropped then no service. There'd be no service for 3 or 4 minutes then it would repeat that cycle again. If I switch from global to cdma/let in settings it would immediately regain full signal. Then the cycle of it dropping out would start again. I got to looking through about phone in settings and realized my imei number was missing, all zeros. I'm assuming that probably is the root of my problems. Not sure what to do, I doubt Verizon can help. Phones not insured or under warranty anymore. I haven't researched this New development on te forums yet it got to late last night. If anyone knows of this problem I could use your help. Thanks
Click to expand...
Click to collapse
If you go into the main Verizon G3 section or possibly the non-Verizon G3 section and use the search field to search for "IMEI" you'll probably find a helpful thread. I think it involves the QPST program on a Windows PC. You'll need the IMEI that it's supposed to have, so hopefully have that on the box or Verizon's website lists it.
Sometimes that's seemed to happen for some people when flashing TOTs, KDZs or ROMs. I've been lucky, it hasn't happened to me through all my flashing over the past year. Once you get it fixed, rooted and put TWRP on, you can back up the IMEI partition in TWRP. It's called something else in TWRP like EI or something - I forget.
Good luck!
roirraW "edor" ehT said:
If you go into the main Verizon G3 section or possibly the non-Verizon G3 section and use the search field to search for "IMEI" you'll probably find a helpful thread. I think it involves the QPST program on a Windows PC. You'll need the IMEI that it's supposed to have, so hopefully have that on the box or Verizon's website lists it.
Sometimes that's seemed to happen for some people when flashing TOTs, KDZs or ROMs. I've been lucky, it hasn't happened to me through all my flashing over the past year. Once you get it fixed, rooted and put TWRP on, you can back up the IMEI partition in TWRP. It's called something else in TWRP like EI or something - I forget.
Good luck!
Click to expand...
Click to collapse
Thanks again I will check that out now
Allen227 said:
Thanks again I will check that out now
Click to expand...
Click to collapse
I have spent sooooo many hours on this. The qpst apk wont see my phone I have done everything the tutorials suggest. the instructions are only applicable if there are no issues, in other words, in a perfect world. I'm sure its something stupid and very simple but I don't even have a place to start. First, its hard to believe this works on all OS's, but it doesn't state anywhere what it is and isn't compatible with. that info would be helpful. i have spent 4 hours a day for over a week trying to get this fixed and I'm no closer than i was when I started. Very frustrating. I'm still open to suggestions or any help that can be offered.
So, I am on the nightly CM12.1 build for the hltespr Note 3 (N900P). This is the one.
I can't seem to find anyone else experiencing this exact issue and it hasn't been posted recently. I have no 4G/LTE service. I have toggled every setting both in the regular settings and under the *#*#4636#*#* settings and nothing seems to work. I was able to flash a stock rom and got LTE service immediately but again got nothing but 3G when I flashed CM12.1 back.
Any suggestions would be greatly appreciated.
Edit: Just wiped data, delvik, cache, etc and loaded the latest nightly fresh and I still get no LTE.
Same here i only get 3g on any room i tink it is something wrong with our modem im using the last kernel h1 let me know if u found the answer
Same here. I flashed Phronesis N5 v6.5 (with the CSC set to SPR and updated my apns-config.xml to a copy from my wife's identical phone) and have only been able to get 3G. I have reverted back to stock and 4G was up and running. This is my headache right now. We need to pull our heads together and get this figured out. My baseband is OK2 right now. I was thinking maybe upgrading to the PH1 would help. It's just odd it works fine with stock.
I just realized wilder90 said he has PH1 running and it's not working. Maybe I will still try it.
*Update- I rolled back to stock and upgraded firmware to PH1. My build says LRX21V.N900PVPUEPH1 but baseband and software still say N900PVPUEOK2. I have 4G working. Do I have to update baseband/software another way?
*Update- I downloaded PH1 from sammobile.com and flashed the update through Odin. Now all says PH1. 4G still working great. I am going to flash Phronesis again and see if there is a change.
*Update- I changed my mind and went with "Sprint Users Rejoice!! MM 6.0.1 Darklord Modded V5 By JCordero31 N5N7 APPS 1/22/17"
I have 4G/LTE working. It doesn't have really any customization available but it works and it's new.