In order to connect the XT1528 to DFS tool, I have followed the following steps. YMMW.
1. Install Motorola usb driver
2. Edit c:/Program Files/Common Files/Motorola Shared/Mobile Drivers/Drivers/motoport.inf
Add the following lines
Code:
; MotoE XT1528
%USBMOTQCDIAGPORT% = USBMOTPORT, USB\VID_22B8&PID_2EC1&MI_00
%USBMOTQCDIAGPORT% = USBMOTPORT, USB\VID_22B8&PID_2EC1&MI_01
%USBMOTQCDIAGPORT% = USBMOTPORT, USB\VID_22B8&PID_2EC1&MI_02
; MotoE XT1528
3. Restart windows
4. Reboot the phone in Bootloader mode - (Vol. down + power)
5. Select "BP Tools" (Use Vol +/- & power button for selection)
6. Connect the Phone to windows using USB cable.
7. In device manager you can see the Motorola QC Diag port
8. This port can be used to connect to DFS tool.
Thanks.
Thanks for the heads up
kmani.k78 said:
In order to connect the XT1528 to DFS tool, I have followed the following steps. YMMW.
1. Install Motorola usb driver
2. Edit c:/Program Files/Common Files/Motorola Shared/Mobile Drivers/Drivers/motoport.inf
Add the following lines
Code:
; MotoE XT1528
%USBMOTQCDIAGPORT% = USBMOTPORT, USB\VID_22B8&PID_2EC1&MI_00
%USBMOTQCDIAGPORT% = USBMOTPORT, USB\VID_22B8&PID_2EC1&MI_01
%USBMOTQCDIAGPORT% = USBMOTPORT, USB\VID_22B8&PID_2EC1&MI_02
; MotoE XT1528
3. Restart windows
4. Reboot the phone in Bootloader mode - (Vol. down + power)
5. Select "BP Tools" (Use Vol +/- & power button for selection)
6. Connect the Phone to windows using USB cable.
7. In device manager you can see the Motorola QC Diag port
8. This port can be used to connect to DFS tool.
Thanks.
Click to expand...
Click to collapse
I Know.......you are going to help me ... I can not install the QC Mode Diag . When I connect the phone to the computer being it started in BP Tools appears as shown in the picture 1 (not shown me QC Diag , just 3 equal devices) , then get the id of hardware as shown in Figure 2. We add the line that appears in the image 3. restart the PC, restart the phone in BP Tools mode and keep getting the same. What am I doing wrong ? I have a Moto E XT1524
There are two section in the motoport.inf file. One for 32bit OS & other for 64bit OS. You pl check where you have added these lines. What is you OS?
Then, You need to change the last two digits as MI_00, MI_01 & MI_02 each one for separate device.
kmani.k78 said:
There are two section in the motoport.inf file. One for 32bit OS & other for 64bit OS. You pl check where you have added these lines. What is you OS?
Then, You need to change the last two digits as MI_00, MI_01 & MI_02 each one for separate device.
Click to expand...
Click to collapse
Hi!, I have a windows 8.1 64 bits... I added the lines that you told me, the way it is in the attached ... but I still do not succeed
pablo_cba said:
Hi!, I have a windows 8.1 64 bits... I added the lines that you told me, the way it is in the attached ... but I still do not succeed
Click to expand...
Click to collapse
I am also using 64 bit OS. Try attached one without any modification. If it is not work change to PID to match yours.
kmani.k78 said:
I am also using 64 bit OS. Try attached one without any modification. If it is not work change to PID to match yours.
Click to expand...
Click to collapse
Is not working... Sorry but whats PID?
I feel it my duty as a person with a long experience of flashing CDMA phones to PagePlus to basically let everyone know that mucking around your phone with DFS can lead to very bad things if you don't know what you're doing.
Sent from my XT1528 using XDA Free mobile app
Right click on the moto device in the Device manager, Update driver, Browse locally & navigate to the motoport.inf folder, click ok.
This will work.
Thanks for figuring this out.
For the XT1527, it needs the following instead:
; MotoE XT1527
%USBMOTQCDIAGPORT% = USBMOTPORT, USB\VID_22B8&PID_2EC5&MI_00
%USBMOTQCDIAGPORT% = USBMOTPORT, USB\VID_22B8&PID_2EC5&MI_01
%USBMOTQCDIAGPORT% = USBMOTPORT, USB\VID_22B8&PID_2EC5&MI_02
; MotoE XT1527
Click to expand...
Click to collapse
hi - did you take SPC (MSL ) from those phone ? and how you do it ?
Any chance this will work with pure xt 1575? Not sure what I need to change to get it to connect.
Still no luck but I did find my vid and uid.
Added these lines:
Code:
; MotoX XT1575
%USBMOTQCDIAGPORT% = USBMOTPORT, USB\VID_22B8&PID_2EE5&MI_00
%USBMOTQCDIAGPORT% = USBMOTPORT, USB\VID_22B8&PID_2EE5&MI_01
%USBMOTQCDIAGPORT% = USBMOTPORT, USB\VID_22B8&PID_2EE5&MI_02
; MotoX XT1575
Using qpst it can read the esn and phone number but phone is unkown and will not connect to programming. It did that before making these changes to the driver.
Please help me
kmani.k78 said:
In order to connect the XT1528 to DFS tool, I have followed the following steps. YMMW.
1. Install Motorola usb driver
2. Edit c:/Program Files/Common Files/Motorola Shared/Mobile Drivers/Drivers/motoport.inf
Add the following lines
Code:
; MotoE XT1528
%USBMOTQCDIAGPORT% = USBMOTPORT, USB\VID_22B8&PID_2EC1&MI_00
%USBMOTQCDIAGPORT% = USBMOTPORT, USB\VID_22B8&PID_2EC1&MI_01
%USBMOTQCDIAGPORT% = USBMOTPORT, USB\VID_22B8&PID_2EC1&MI_02
; MotoE XT1528
3. Restart windows
4. Reboot the phone in Bootloader mode - (Vol. down + power)
5. Select "BP Tools" (Use Vol +/- & power button for selection)
6. Connect the Phone to windows using USB cable.
7. In device manager you can see the Motorola QC Diag port
8. This port can be used to connect to DFS tool.
Thanks.
Click to expand...
Click to collapse
---------
please help
I have a Motorola E (2nd generation) whith 4g lite xt1528 android version 5.1
I want to make it in a mode diag
To appear in the DFS program
but I could not
Although I erected definitions
Show me in Device Manager
Unknown Device:
XT1528
XT1528
XT1528
I use Windows 10 64-bit
Is there a way fabricators or lines in a file motoport.inf
What are the lines that fabricators in that file and how
Please help me
I should be grateful to you
Related
X-Posted from the Mi6 forum and Stack Overflow. I wanted to do this the whole time I had my Mi5 (RIP) but couldn't figure out how.
Could anybody test on their Mi5 and let me know if it works?
kylemd said:
I know that looking for this answer has bugged me for the past few years, so figured I'd x-post from Stack Overflow. I have found the solution to switching either SIM off in the Mi6 automatically. Will likely work with other phones.
The whole question and answer you can find on Stack Overflow here.
To get the required index out of your device, you'll need to run the following commands from command prompt:
Download jadx from here
ADB pull the devices framework.jar (adb pull /system/framework/framework.jar)
Open the .jar file with 7-Zip and extract the *.dex files.
Open each .dex file with jadx-gui until you find the one with the following tree: com.android.internal.telephony.ITelephony
Search for the item TRANSACTION_setSimPowerStateForSlot. Note the = x after it; this is the index number.
Now you have the index number you can test the following command in adb shell (or Tasker, with the "run shell" function). You will need to "su" in shell, or set Tasker to "Use Root".
service call phone x i32 y i32 z
Where:
x = index number you fetched previously,
y = your subscription ID (generally, SIM1 = 0, SIM2 = 1)
z = whether on (1) or off (0)
Click to expand...
Click to collapse
Of course, now that you can execute it in Tasker you can now switch either SIM off at specific times.
I've verified that it does indeed switch the SIM off (calls go straight to voicemail right after this command is executed) but I'm unsure of any further effects this switch has.
Enjoy!
Click to expand...
Click to collapse
Click to expand...
Click to collapse
I am trying to root a Lava Z60 phone, for which I try to enter fastboot mode. Using either "adb reboot bootloader" or powerbutton + volume up and selecting fastboot, I get to a blank screen. The device ID in USB changes to a different one from that of adb. I can see the device in dmesg as:
Code:
[30482.597989] usb 2-1.1: new high-speed USB device number 53 using ehci-pci
[30482.707638] usb 2-1.1: New USB device found, idVendor=0e8d, idProduct=20ff
[30482.707643] usb 2-1.1: New USB device strings: Mfr=3, Product=4, SerialNumber=5
[30482.707646] usb 2-1.1: Product: Android
[30482.707649] usb 2-1.1: Manufacturer: Android
[30482.707652] usb 2-1.1: SerialNumber: 0123456789ABCDEF
But when I run "fastboot devices" the result is empty ( I tested on Linux, windows and FreeBSD). To debug I downloaded the python version of adb and fastboot tools and put in some print statements for the data sent to the phone and returned by it . The library expects these values(settings) to be returned from the device in fastboot mode(they are hardcoded):
class = 0xff, subclass = 0x42, protocol = 0x03
Instead my phone returns:
class = 0x03, subclass = 0x00, protocol = 0x00
I tried changing the hardcoded values to the ones returned by the phone but it resulted in a USB error. So I think my phone is not properly entering fastboot mode. Why could that be, and how can it be fixed?
N30xda said:
I am trying to root a Lava Z60 phone, for which I try to enter fastboot mode..........
Click to expand...
Click to collapse
I don't have this device myself but, your best bet would be to check out one of the following Guides regarding Fastboot.
https://forum.xda-developers.com/showthread.php?t=3239537
https://forum.xda-developers.com/showthread.php?t=2277112
There's other similar Guides/Tutorials on the forum but, those should give you a good start for what you are looking to do. Don't be afraid to ask for some member guidance within one of them too.
Good Luck!
~~~~~~~~~~~~~~~
Unless asked to do so, PLEASE don't PM me regarding support. Sent using The ClaRetoX Forum App on my Apple Macintosh.
How can i update my lava z 60 into android q pls tell
ASHOKJAIN said:
How can i update my lava z 60 into android q pls tell
Click to expand...
Click to collapse
Don't think stock Android Q firmware is available for this device. If available then you've to use SP Flash Tool in order to install it.
Hello,
I saw on a website someone has installed the Windows 11 on a Smartphone.
Think you is it possible to do it on the Surface RT ? It's the same architecture ARM.
So far there is no ARM32 builds of Win11, so no. Not yet, anyways. The smartphone had to have been ARM64/Aarch64, the Surfaces are ARM32.
frylockk19 said:
So far there is no ARM32 builds of Win11, so no. Not yet, anyways. The smartphone had to have been ARM64/Aarch64, the Surfaces are ARM32.
Click to expand...
Click to collapse
Okey I understand now
Thanks for your help !
Who knows, maybe one day !
tagdevil said:
Okey I understand now
Thanks for your help !
Who knows, maybe one day !
Click to expand...
Click to collapse
No problem! Maybe it will be possible one day, only the future will be able to tell us.
I'm feelling ready to brick an RT Surface (1st Gen), to test Windows11. I don't know what is going to happen. But, who knows...?
And in my hands, have a Surface Pro 1st Gen wich, i think is an I5 Processor, 64-bit. At this equipment, i'm trying to restore/fix boot record. I've allready entered in recovery mode. But forgot to fix this problem, and now i need again to enter in recovery mode. But it allways enter in bios setup!
MareAlta said:
I'm feelling ready to brick an RT Surface (1st Gen), to test Windows11. I don't know what is going to happen. But, who knows...?
And in my hands, have a Surface Pro 1st Gen wich, i think is an I5 Processor, 64-bit. At this equipment, i'm trying to restore/fix boot record. I've allready entered in recovery mode. But forgot to fix this problem, and now i need again to enter in recovery mode. But it allways enter in bios setup!
Click to expand...
Click to collapse
The RT just won't boot to Windows, only issue it'll have as there is for sure no 32bit or ARM32/Aarch32 builds, only WinPE is 32bit (you could recover it). As for your Pro 1st gen, it'll be fine. Just be sure to bypass the TPM 2.0 thing.
Windows is some of the worst OS ever.
VD171 said:
Windows is some of the worst OS ever.
Click to expand...
Click to collapse
Yup. Linux/FOSS for life
No, because windows RT used ARM 32, but windows 11 only support ARM64
Data.hu | Fájl nem létezik
Az adott fájl nem létezik. Valószínűleg a tulajdonosa már törölte rendszerünkből, vagy a 2001. évi CVIII. törvény alapján, jogsértés miatt került eltávolításra.
data.hu
I've installed a recent w11 build (on ARM system tho) and it just needed:
HKEY_LOCAL_MACHINE\SYSTEM\Setup
Key: LabConfig
DWORD 32bit
BypassTPMCheck = 1
BypassRAMCheck = 1
BypassSecureBootCheck = 1
Computer\HKEY_LOCAL_MACHINE\SYSTEM\Setup
MoSetup Key
Dword 32 Bit
AllowUpgradesWithUnsupportedTPMOrCPU
Value = 1 Hexadecimal
How to open registry editor on installer:
1. Press Shift+F10
2. Once command prompt window appears type "regedit" and press enter
Option 2:
1. Ensure you're on main page with the Install Now button
2. Press the "Repair your computer" link on bottom
3. Troubleshoot -> Command Prompt
4. Once command prompt window appears type "regedit" and press enter
Varga Laci said:
Data.hu | Fájl nem létezik
Az adott fájl nem létezik. Valószínűleg a tulajdonosa már törölte rendszerünkből, vagy a 2001. évi CVIII. törvény alapján, jogsértés miatt került eltávolításra.
data.hu
I've installed a recent w11 build (on ARM system tho) and it just needed:
HKEY_LOCAL_MACHINE\SYSTEM\Setup
Key: LabConfig
DWORD 32bit
BypassTPMCheck = 1
BypassRAMCheck = 1
BypassSecureBootCheck = 1
Computer\HKEY_LOCAL_MACHINE\SYSTEM\Setup
MoSetup Key
Dword 32 Bit
AllowUpgradesWithUnsupportedTPMOrCPU
Value = 1 Hexadecimal
How to open registry editor on installer:
1. Press Shift+F10
2. Once command prompt window appears type "regedit" and press enter
Option 2:
1. Ensure you're on main page with the Install Now button
2. Press the "Repair your computer" link on bottom
3. Troubleshoot -> Command Prompt
4. Once command prompt window appears type "regedit" and press enter
Click to expand...
Click to collapse
ARM64 orrrrr...?
frylockk19 said:
ARM64 orrrrr...?
Click to expand...
Click to collapse
Arm plus Intel, AMD Have a look around on Telegram.
Varga Laci said:
Arm plus Intel, AMD Have a look around on Telegram.
Click to expand...
Click to collapse
What group
Wait, do you think I asked what CPU the keys work on? My bad if so, was asking if you installed Windows on an ARM64 or ARM32 CPU
I'm looking to pinout both test pins. I bought this phone a few days ago. I unlocked it with TWRP, I looked at the possibilities. I made a mistake with TWRP by switching the system to sideload B (I chose between A and B) and the system refused to start. I do not have access to the bootloader with the buttons. I only enter QDLoader HS-USB Driver mode working. I read the instructions on how to make a blank flash. I took the 18 files out of the phone and made a new blank flash for this model - moto g9 power / but in the end it gives me an error. Now I'm looking for a solution. - "C: \ Documents and Settings \ Administrator \ Desktop \ MOTO G9 POWER blankflash \ Blankflash for G9 POWER>. \ Qboot.exe blank-flash Motorola qboot utility version 3.86 [0.000] Opening device: \\. \ COM4 [0.000] Detecting device [0.000] ... cpu.id = 333 (0x14d) [0.000] ... cpu.sn = 2936128399 (0xaf01c38f) [0.000] Opening singleimage [0.000] Loading package [0.000] ... filename = pkg.xml [0.000] Loading programmer [0.000] ... filename = programmer.elf [0.000] Sending programmer [0.156] Handling things over to programmer [0.156] Identifying CPU version [0.156] Waiting for firehose to get ready [3.297] ... SM_KAMORTA_H 1.0 [3.297] Determining target secure state [3.297] ... secure = yes [3.375] Configuring device ... [3.391] Flashing GPT ... [3.391] Flashing partition with gpt.bin [3.406] Initializing storage [3,484] ... blksz = 512 [37.016] Re-initializing storage ... [37.016] Initializing storage [37328] Flashing bootloader ... [37.344] Flashing abl_a with abl.elf [37.344] partition abl_a not found! [37.359] ERROR: do_package () -> do_recipe () -> do_flash () -> pt_find () -> not found [37.375] Check qboot_log.txt for more details [37.375] Total time: 37.375s FAILED: qb_flash_singleimage () -> do_package () -> do_recipe () -> do_flash () -> pt_find () -> not found "the last message puzzles me. I want to transfer the system to sideload A again, so I have to reset the device firmly. Are there people familiar with the possibilities?
2 I built a blankflash for the Moto G8
1 How To Blank Flash & Fix/Repair Hard Bricked Motorola Devices/Moto G8+|Tutorial Get It Working Again - YouTube
Version Bootloader MBM-3.O-cebu retail 232f3ba894-201209
motostockrom.com/motorola-moto-g9-power-xt2091-3
I'm looking to pinout both test pins.
Have you tried using LMSA?
It recovered a dead phone for me once.
Rescue and Smart Assistant (LMSA)
Also, I too once accidentally switched slot to B, and system didn't boot. However, I was able to get into fastboot mode and switch by entering the command to switch slots.
https://support.lenovo.com/bg/en/downloads/ds101291 i saw this but my computer is 32 bit / i am looking for the program qualcomm edl mode flash tool or something like Axon10Pro_ (More) _EDL_Tools_v1.1d because i want to make active a siteloader because i saw that this can be done not so difficult otherwise for edl pinout I saw how it works and no problem
man88nam said:
https://support.lenovo.com/bg/en/downloads/ds101291 i saw this but my computer is 32 bit / i am looking for the program qualcomm edl mode flash tool or something like Axon10Pro_ (More) _EDL_Tools_v1.1d because i want to make active a siteloader because i saw that this can be done not so difficult otherwise for edl pinout I saw how it works and no problem
Click to expand...
Click to collapse
qualcomm edl mode flash tool / Axon10Pro_ (More) _EDL_Tools_v1.1d
In those .XML files, can you delete the line that says "abl" and try again?
I will do, but these files can be downloaded according to the instructions on how to make closed files extracted from the phone itself
https://www.reddit.com/r/MotoG/comments/k73n66
I downloaded from the bootloader 18 files that are original, this is in connection with blank flash, where in the end there is an error, because eight made active "B" sector instead of A
I removed the ABL file from the XML, but the error remains, plus the message for a missing ABL file ELF
[ 37.297] file abl.elf not found in singleimage.bin!
[ 37.297] ERROR: do_package()->do_recipe()->do_flash()->not found
[ 37.297] Check qboot_log.txt for more details
[ 37.297] Total time: 37.297s
I'm just looking for an EDL program that works similar to this command line Set Bootable Partition- Slot A / run_AB-partition-swap - but here it wants some text file for the presence of a port, port_trace.txt
I'm sorry, I can't help further here. Even though the active slot is B, the partition abl_a should exist and should be flashable regardless. It looks as though there isn't such a partition at all, which I don't even know how that happened.
The tool which you are using is correct, it's doing its job properly. Are you sure you have the right firmware version and software channel? Because bootloader.img differ depending on the firmware version and the carrier. I'd also suggest downloading from https://mirrors.lolinet.com/firmware/moto/cebu/official/, instead of the link you mentioned, motostockroms.
Also, try asking in this Telegram group: https://t.me/lolinet. There are people on there who are more knowledgeable, maybe they can help.
After trying the firmware image from lolinet and trying the process again with that firmware, I'd try to get into bootloader mode once again through power buttons, and if that doesn't work, send the phone into the service center.
Motorola_Moto_G9_Power_XT2091-3_RETUK_CEBU_RETAIL_QZC30.Q4-22-57_10_by_(motostockrom.com) With the TWRP program I chose with active slot B / I don't know if it deleted the content from slot A of the bootloader. By the way, I downloaded the original product firmware XT2091-3 according to the instructions for this, which I get when I try blank flash / I have no idea what to do, so I'm looking for a program "qualcomm edl mode flash tool" and I constantly get Indian sites with dangerous behavior.
I thank you for your time
Hey,
Today I found EDL points for Moto G9 power. Infact im also facing firmware issue.
I accidentally locked bootloader with stockrom again trying to unlock but not working.
Causing No valid OS to boot.
if i try unlock again showing message like " enable OEM unlocking in developer options"
unfortunately not podsible. But still waiting for proper EDL flash tool.
feel free to guide if any one got resolution.
Hi everyone,
I need some help. I installed Windows 11 21H2 on "Unsupported hardware" like Microsoft said, but it runs smoothly on my computer. 22H2 update came and gave Windows 11 new design and features, and i want so much to install it without losing any data but i don't receive the update in Windows Update. I made some searches about it and i saw this update won't come for "Unsupported Hardware" users, and i don't find any KB updates in the web, so i have to reinstall windows and i won't loose all of my works, software and configuration, any to install this like normal ?
Thanks for reply
Download the latest version of Rufus from here.
Head over to the official website for Windows 11 ISO download.
Under the Download Windows 11 Disk Image (ISO) section, click Select Download, and select Windows 11.
This will prompt you to select the language for your ISO.
Hope This Works,
Peter
I had this exact dilemma when 22H2 came out. All I had to do was create the AllowUpgradesWithUnsupportedTPMOrCPU registry tweak and download the 22H2 iso from Microsoft's website. You don't even need to make a bootable USB, you can just mount the iso and upgrade from there.
Make sure when you download the iso to select the same language as the one you're upgrading, otherwise it will force you to clean install.
mrcutiepatootie said:
I had this exact dilemma when 22H2 came out. All I had to do was create the AllowUpgradesWithUnsupportedTPMOrCPU registry tweak and download the 22H2 iso from Microsoft's website. You don't even need to make a bootable USB, you can just mount the iso and upgrade from there.
Make sure when you download the iso to select the same language as the one you're upgrading, otherwise it will force you to clean install.
Click to expand...
Click to collapse
ok thx
mrcutiepatootie said:
I had this exact dilemma when 22H2 came out. All I had to do was create the AllowUpgradesWithUnsupportedTPMOrCPU registry tweak and download the 22H2 iso from Microsoft's website. You don't even need to make a bootable USB, you can just mount the iso and upgrade from there.
Make sure when you download the iso to select the same language as the one you're upgrading, otherwise it will force you to clean install.
Click to expand...
Click to collapse
bro it is not working. can you help?
sundaraprakash said:
bro it is not working. can you help?
Click to expand...
Click to collapse
Try this
edit : tried to attach a script but it might be blocked
Copy this into a text file and change extension to .cmd
@(set "0=%~f0"^)#) & powershell -nop -c iex([io.file]::ReadAllText($env:0)) & exit/b
#:: double-click to run or just copy-paste into powershell - it's a standalone hybrid script
#:: v5 of the toggle script uses programdata instead of system32, no longer deletes appraiserres.dll, and clears bypass folder
#:: uses IFEO to attach to Virtual Disk Service Loader process running during setup, then creates a bypass dir
#:: it must also do some ping-pong renaming of vdsldr in programdata
#:: you probably don't need to have it installed at all times - just when doing feature updates or manual setup within windows
#:: hence the on off toggle just by running the script again
#:: can get 11 release beta or dev builds via Windows Update after using OfflineInsiderEnroll by whatever127 and abbodi1406
$_Paste_in_Powershell = {
$N = "Skip TPM Check on Dynamic Update"; $X = @("' $N (c) AveYo 2021 : v4 IFEO-based with no flashing cmd window")
$X+= 'C = "cmd /q AveYo /d/x/r pushd %systemdrive%\\$windows.~bt\\Sources\\Panther && mkdir Appraiser_Data.ini\\AveYo&"'
$X+= 'M = "pushd %allusersprofile%& ren vd.exe vdsldr.exe &robocopy ""%systemroot%/system32/"" ""./"" ""vdsldr.exe""&"'
$X+= 'D = "ren vdsldr.exe vd.exe& start vd.exe -Embedding" : CreateObject("WScript.Shell").Run C & M & D, 0, False'
$K = 'HKLM:\SOFTWARE\Microsoft\Windows NT\CurrentVersion\Image File Execution Options\vdsldr.exe'
$P = [Environment]::GetFolderPath('CommonApplicationData'); $F = join-path $P '11tpm.vbs'; $V = "wscript $F //B //T:5"
if (test-path $K) {
remove-item $K -force -ea 0 >''; del $F -force -ea 0; del (join-path $P 'vd.exe') -force -ea 0
write-host -fore 0xf -back 0xd "`n $N v4 [REMOVED] run again to install "
} else {
new-item $K -force -ea 0 >''; set-itemproperty $K 'Debugger' $V -force -ea 0; [io.file]::WriteAllText($F, $X-join"`r`n")
write-host -fore 0xf -back 0x2 "`n $N v4 [INSTALLED] run again to remove "
} ; rmdir $([Environment]::SystemDirectory[0]+':\\$Windows.~BT\\Sources\\Panther') -rec -force -ea 0; timeout /t 5
} ; start powershell -args "-nop -c & {`n`n$($_Paste_in_Powershell-replace'"','\"')}" -verb runas
$_Press_Enter
#::
Hey Can You Really Upgrade To 11 On An Unsprouted Laptop
sundaraprakash said:
bro it is not working. can you help?
Click to expand...
Click to collapse
Create the following registry key in HKEY_LOCAL_MACHINE\SYSTEM\Setup\MoSetup
Name: AllowUpgradesWithUnsupportedTPMOrCPU
Type: REG_DWORD
Value: 1
Exit regedit and upgrade.
MadManMaitland said:
Hey Can You Really Upgrade To 11 On An Unsprouted Laptop
Click to expand...
Click to collapse
This thread is for upgrading on an existing Windows 11 install on an unsupported device without losing data. If you haven't installed Windows 11 on your unsupported device there are plenty of ways to do this here.
mrcutiepatootie said:
Create the following registry key in HKEY_LOCAL_MACHINE\SYSTEM\Setup\MoSetup
Name: AllowUpgradesWithUnsupportedTPMOrCPU
Type: REG_DWORD
Value: 1
Exit regedit and upgrade.
This thread is for upgrading on an existing Windows 11 install on an unsupported device without losing data. If you haven't installed Windows 11 on your unsupported device there are plenty of ways to do this here.
Click to expand...
Click to collapse
this one worked thx so much
You can also use rufus to create a "tweaked" version of the USB stick installer from the original ISO, then it will update without a hick.
viktak said:
You can also use rufus to create a "tweaked" version of the USB stick installer from the original ISO, then it will update without a hick.
Click to expand...
Click to collapse
I have used both Rufus and Ventoy, both work great installing Win 11 on any workstation or PC.
Joseph said:
I have used both Rufus and Ventoy, both work great installing Win 11 on any workstation or PC.
Click to expand...
Click to collapse
I think rufus is better
F-Google said:
I think rufus is better
Click to expand...
Click to collapse
I agree, but I like the fact ventoy can hold more than one ISO, as much as your thumb drive can hold, I've got a 64gb thumb drive with about 5 different OS ISO.
MadManMaitland said:
Hey Can You Really Upgrade To 11 On An Unsprouted Laptop
Click to expand...
Click to collapse
Yes, you definitely can (guide) but on all of my devices, I always received updates like a charm... except now the upgrade to 22H2.
I can verify it worked using the Registry hack + downloading the ISO. All my 'incompatible' systems updated to 22H2 like a charm.
use this
GitHub - AveYo/MediaCreationTool.bat: Universal MCT wrapper script for all Windows 10/11 versions from 1507 to 21H2!
Universal MCT wrapper script for all Windows 10/11 versions from 1507 to 21H2! - GitHub - AveYo/MediaCreationTool.bat: Universal MCT wrapper script for all Windows 10/11 versions from 1507 to 21H2!
github.com
run
Skip_TPM_Check_on_Dynamic_Update.cmd
download windows 11
Download Windows 11
This will be the latest
instal again and use upgrade
If nothing helps try to make a inplace upgrade using a UPDATED Windows 11 Isofile, see this german site...
Windows 11 Inplace Upgrade Reparatur oder Feature Update
This works without losing your settings and programs!