Hi fellow xda'rs,
I recently bought a Android TV Stick from Geek(app) from china.
I thought I had found a bargain as its specs were:-
2GB RAM
Quad Core CPU
16GB Storage
I managed to snap this up for £24 which I thought was a bargain but when I got the device delivered and was using it I thought it was a little on the slow side so I began to think it was a clone as its default OS theme was not the same as the usual CX919's aswell.
So I wanted to flash the device with a new ROM specifically the Finless 1.6b ROM.
So after following the instructions to installing the ROM using the software provided with the ROM download I managed to install the drivers and get the software to recognize the device. I then wiped the NAND and attempted to install the ROM but it failed .
Now the device does not boot at all and is not recognized by the PC. Windows just states the device is not recognized and has malfunctioned
So I cannot flash any other or what I believer I have found to be the original ROM for the clone device.
The board states its a GXT_D16_LP_V1.8 150310
I have seen that there are tutorials on putting the device into Mask Flash mode by shorting pins but as this is for the genuine CX919 my board is totally different and does not have the pins available to short I think.
In short could anyone help me to put this device into Mask Flash mode and tell me what id need to do and what pins to short please?
I have attached a couple of pictures of the device and board.
lowery91 said:
hi fellow xda'rs,
i recently bought a android tv stick from geek(app) from china.
I thought i had found a bargain as its specs were:-
2gb ram
quad core cpu
16gb storage
i managed to snap this up for £24 which i thought was a bargain but when i got the device delivered and was using it i thought it was a little on the slow side so i began to think it was a clone as its default os theme was not the same as the usual cx919's aswell.
So i wanted to flash the device with a new rom specifically the finless 1.6b rom.
So after following the instructions to installing the rom using the software provided with the rom download i managed to install the drivers and get the software to recognize the device. I then wiped the nand and attempted to install the rom but it failed .
Now the device does not boot at all and is not recognized by the pc. Windows just states the device is not recognized and has malfunctioned
so i cannot flash any other or what i believer i have found to be the original rom for the clone device.
The board states its a gxt_d16_lp_v1.8 150310
i have seen that there are tutorials on putting the device into mask flash mode by shorting pins but as this is for the genuine cx919 my board is totally different and does not have the pins available to short i think.
In short could anyone help me to put this device into mask flash mode and tell me what id need to do and what pins to short please?
I have attached a couple of pictures of the device and board.
Click to expand...
Click to collapse
problem solved! :d
i found the mask flash mode pins to short by trial and error and luckily enough after 1 hour i solved it and got the pc to flash it back to its original rom. If anyone has the same device or issues and would like to know how to solve this i will be happy to help
I would be interested. I have a very similar clone (was supposed to be mk809iv). I have the same board although possibly different chipset.
I haven't bricked it (yet) but will probably do so if I can't find a way to root it. I think it may have come pre-rooted as super su was preinstalled but it has never worked (possibly because the app updated but not the binary?). I have since tried to update the binary and killed the root access completely.
Questions:
Is the ROM you used pre-rooted or rootable (if you've tried)?
Which pins need shorting? I have a button on the side that may be doing the same thing.
OT. How do I upload images or can I not as a new member?
Thanks in advance
any guide? i have the same device or where to download rom?
If your still looking, i might be able to help with a rom, root, and guide.
Thank you but managed to get root the same day you posted. I may still give it a go when my new tv box turns up though if you dont mind posting the info?
For anyone else interested in how I gained root:
1. Search for, download and install kingroot 4.6.5 (this is the version I used, only the latest version is available from official site and cannot be sure next steps will work with it)
2. Run kingroot and follow steps to gain root (dongle may reboot)
3. BUY super sume from play store.
4. Run super sume and follow steps to replace kingroot with super su.
what pins did you short
I am having problems flashing my hdmi stick . I can't get it to flash mode. which pins did you shorted?
can you email me a picture of it? [email protected] thanks
Lowery91 said:
problem solved! :d
i found the mask flash mode pins to short by trial and error and luckily enough after 1 hour i solved it and got the pc to flash it back to its original rom. If anyone has the same device or issues and would like to know how to solve this i will be happy to help
Click to expand...
Click to collapse
Hello,
Having some problems with this stick .Messed up trying to flash a non rooted rom and now I only get a blue icon in rkbatch tool ( after short pin 5-6 ) and nothing happens. Download boot fail errors for a year...
Can someone help me please?
Is it the same model? What version of rkflash tool are you using. And what version are you trying to flash. In my case I didn't need to short any pins.
spade2be said:
Is it the same model? What version of rkflash tool are you using. And what version are you trying to flash. In my case I didn't need to short any pins.
Click to expand...
Click to collapse
I've used several batchtools from 1.5 ( doesn't see my device at all ) to 1.8, different roms ( neomod, finless, stock cx919 roms )hoping one would give me something. All different bootloaders 1.24, 2.08, 2.13,...
I'm going to check mine out. It's been a minute since I used it. But I got the rock chip tool and the img file. I'll zip it up and pm you the link asap.
spade2be said:
I'm going to check mine out. It's been a minute since I used it. But I got the rock chip tool and the img file. I'll zip it up and pm you the link asap.
Click to expand...
Click to collapse
Thnx a million for your help. I've gone bonkers over this hahaha
Lowery91 said:
problem solved! :d
i found the mask flash mode pins to short by trial and error and luckily enough after 1 hour i solved it and got the pc to flash it back to its original rom. If anyone has the same device or issues and would like to know how to solve this i will be happy to help
Click to expand...
Click to collapse
what pins did you short
I am having problems flashing my hdmi stick . I can't get it to flash mode. which pins did you shorted?
can you email me a picture of it? [email protected] thanks
Related
i just bought a chinese htm xs5292 runnin 4.1.1 i want to root and upgrade to 4.3 any help on how to do this would be greatly appreciated, here are the specs
manufacturer - htm
model - x5292
android version - 4.1.1
kernel - x5292 dual core
software - mt5617-c913-en-vo5
hardware - c913-v1.02
i'm a first timer at this so please speak like you would to a child (even though i'm 35)
many thanks in advance
paul
paul0909 said:
i just bought a chinese htm xs5292 runnin 4.1.1 i want to root and upgrade to 4.3 any help on how to do this would be greatly appreciated, here are the specs
manufacturer - htm
model - x5292
android version - 4.1.1
kernel - x5292 dual core
software - mt5617-c913-en-vo5
hardware - c913-v1.02
i'm a first timer at this so please speak like you would to a child (even though i'm 35)
many thanks in advance
paul
Click to expand...
Click to collapse
I can help you get rooted. First you will need to install drivers on your PC so your device can communicate with the root program. Then try this:
http://forum.xda-developers.com/showpost.php?p=43163569&postcount=7
If that dont work, let me know. You can always use MTK Droid Tools and SP flash tool to pull your stock recovery and port it into a custom recovery that will allow you to flash a simple root.zip
Hope this helps!
usb drivers
thanks Klown80, that looks like it should work, but first i need to install my usb drivers, i have loked at a ton of sites and they all didnt work, i need spreadtrum usb drivers, but can't figure out wich ones, a few said they all worked on any spreadtrum phone, but either im installing them incorrectly, or they simply didnt work,
again, thanks for any help in advance
paul
paul0909 said:
thanks Klown80, that looks like it should work, but first i need to install my usb drivers, i have loked at a ton of sites and they all didnt work, i need spreadtrum usb drivers, but can't figure out wich ones, a few said they all worked on any spreadtrum phone, but either im installing them incorrectly, or they simply didnt work,
again, thanks for any help in advance
paul
Click to expand...
Click to collapse
Try using this, it installs drivers for many different phones, it may not be the actual manufacturers drivers for your specific device but it will help get your phone talking to your PC:
http://www.snappea.com/
Also - Make sure you are going into settings and turning USB debugging on. You can usually find this under Settings > Developer Options.
snapea
Again, thanks Klown, but no joy, i tried serveral times and after 15 - 20 mins of "fobulating" (is that even a real word ) my phone it said "failed to processs phones data" i tried restarting both devices etc and a couple of other thing suggested but no joy.
Any other ideas, as always thanks in advance.
Paul
oh ps, i also tried to connect to snapea via wifi, but got the same message
paul0909 said:
Again, thanks Klown, but no joy, i tried serveral times and after 15 - 20 mins of "fobulating" (is that even a real word ) my phone it said "failed to processs phones data" i tried restarting both devices etc and a couple of other thing suggested but no joy.
Any other ideas, as always thanks in advance.
Paul
oh ps, i also tried to connect to snapea via wifi, but got the same message
Click to expand...
Click to collapse
Try these drivers
https://www.dropbox.com/sh/oaslz8xuxk7ag50/VRzHnZvA-b
finally
\it worked, can't thank you enough, one more bothersome question, now i have my phone rooted how do i safely, and i emphasise safely upgrade from 4.1.1 to 4.3
I have looked into it a bit myself, and am in half a mind to give it a go, but the warnings about bricking my phone always puts me off, so once again, thanks in advance for any help given, and many thanks for the help so far.
Paul
paul0909 said:
\it worked, can't thank you enough, one more bothersome question, now i have my phone rooted how do i safely, and i emphasise safely upgrade from 4.1.1 to 4.3
I have looked into it a bit myself, and am in half a mind to give it a go, but the warnings about bricking my phone always puts me off, so once again, thanks in advance for any help given, and many thanks for the help so far.
Paul
Click to expand...
Click to collapse
Go here and download MTK Droid Tools from first post:
http://forum.xda-developers.com/showthread.php?t=2160490&styleid=18
Run the program and connect your phone to PC, this tool will tell you lots of info about your phone but the main function is to possibly back up your stock firmware (This is good to have if you plan on trying to flash anything to the phone, this way you will have your stock files to fall back on in case something you flash to the phone does not work.) Once you have MTK Droid Tools running and phone connected, what does it say next to Hardware on the phone info tab please?
I am not sure off top of my head about updating to a higher version of Android but this back up step is REALLY important. It is hard if not impossible to find stock firmware floating around on the net for these chinese clone devices. IF you have stock files backed up you can flash almost anything you want knowing you have a way to restore your phone to working order. IF you look around here on XDA you will see tons of posts by people looking for the stock firmware for their clone phone after soft bricking it playing around. Sadly there is not much help for them unless they find someone with the EXACT same phone and are willing to share their back up (if the next person made one theirselves that is!)
hardware
Klown80 said:
Go here and download MTK Droid Tools from first post:
http://forum.xda-developers.com/showthread.php?t=2160490&styleid=18
Run the program and connect your phone to PC, this tool will tell you lots of info about your phone but the main function is to possibly back up your stock firmware (This is good to have if you plan on trying to flash anything to the phone, this way you will have your stock files to fall back on in case something you flash to the phone does not work.) Once you have MTK Droid Tools running and phone connected, what does it say next to Hardware on the phone info tab please?
I am not sure off top of my head about updating to a higher version of Android but this back up step is REALLY important. It is hard if not impossible to find stock firmware floating around on the net for these chinese clone devices. IF you have stock files backed up you can flash almost anything you want knowing you have a way to restore your phone to working order. IF you look around here on XDA you will see tons of posts by people looking for the stock firmware for their clone phone after soft bricking it playing around. Sadly there is not much help for them unless they find someone with the EXACT same phone and are willing to share their back up (if the next person made one theirselves that is!)
Click to expand...
Click to collapse
Thanks again, while i go to the link and follow the next steps i thought i'd put up the hardware version you asked for
hardware - c913-v1.02
Paul
edit
even though my pc now recognises the fact that tere is a spreadtrum phone in my devices list and i managed to root it ok, when i load up mtk droid tools it says "the device isn't revealed, connect or reconnect a cable"
needless to say i tried reconnecting and it didn't change i downloaded the adb drivers from the link under the mtk link but have no idea what to do with them,
appologies for my ignorance in all of this, but like i said in my first post, i have no idea what i'm doing with all this, thanks
paul
pps the hardware version i posted was from the info on my phone
Hello everyone! Happy new month as we say in Greece!
I'm new to your forum (but I visit the forum way to often to find answers to some of the problems that my friends have with their android phones)
I am a iOS user since the release of the first iPhone (2G) and i still use that phone as my primary device.
Due to economical issues I never could buy a newer version of the device.
So I thought... an iPhone clone might do the trick for me!
SO I bought a used Goophone i5.
The specs that antutu gave me was that the phone had:
Quad-Core CPU (MT6589 if I'm not mistaken) --> which is a lie, because the phone in factory mode (Power + Vol down told me it was a dual core mt6577)
2GB RAM
I wanted to fresh install the ROM of the phone and I went to needrom.com to find the ROM for my phone.
I extracted the downloaded files and with SP Flashtool i followed the steps to install the ROM.
But once the green circle appeared in my PC monitor, and told me that everything was OK I ejected the phone cable and tried to power on the device.
The device doenst show ANY kind of response to anything (no dev manager port appearance or anything) and that means i cannot install another ROM or even go to recovery mode to install another rom OR even try another ROM from SP Flashtool.
I tried to locate the test point of the device but i couldn't since I've never tried that before and i am kinda scared that i will ruin my new pretty shiny iPhone clone.
Here are some images of the inside of the device (not taken by me) :
http://imagizer.imageshack.us/a/img541/2850/ebne.jpg
http://imagizer.imageshack.us/a/img132/1700/u36i.jpg
My questions are the following:
1) Can someone help me find the test point and give me step-by-step instructions on how to connect my phone again to SP Flashtool?
2) Is there a way to avoid finding the TP and just flashing a new ROM?
3) Does someone have the same problem as me out there?
4) Is there a newer ROM with ios7 looks?
Thanks to all,
hope you can all help me and then help you if needed :highfive:
The articles that I have already tried and researched are:
http://forum.xda-developers.com/showthread.php?t=2417060
http://translate.google.gr/translat...Z3x&rls=org.mozilla:en-US:official&channel=sb
http://translate.google.gr/translat...W8x&rls=org.mozilla:en-US:official&channel=sb
http://forum.china-iphone.ru/unbrick-goophone-i5-tk-6575-t29417.html
http://forum.xda-developers.com/showthread.php?t=1943442
UP please
UP . anyone?
3985993 4393
UP. Anyone?
up!
No one knows how to do this?
The things I also tried was to charge the battery from a external charger with leads and connect it to another device to see if it still works.
The battery so does work
But still cant locate the test point and cant connect the device to SP Flashtool.
Please help XDA members
Hi,
Just bought this tv-box and while trying to update it with a different rom bricked it. It shows just red LED and nothing happens, also while trying go into recovery (toothpick + power cable).
Does anybody have detailed tutorial how to unbrick the box ?
Thanx in advance.
I am in your very same situation. Tried the sd card burning method and also the usb one, but no success at all. Hope there is some solution.
resadent said:
I am in your very same situation. Tried the sd card burning method and also the usb one, but no success at all. Hope there is some solution.
Click to expand...
Click to collapse
Maybe someone could place a foto with indicated pins (to make circuit on flash chip) to go into recovery mode ?
etemmu666 said:
Hi,
Just bought this tv-box and while trying to update it with a different rom bricked it. It shows just red LED and nothing happens, also while trying go into recovery (toothpick + power cable).
Does anybody have detailed tutorial how to unbrick the box ?
Thanx in advance.
Click to expand...
Click to collapse
Head over to FreakTab, they have tutorials on how to unbrick it
Patrck744 said:
Head over to FreakTab, they have tutorials on how to unbrick it
Click to expand...
Click to collapse
We, or at least I, have tried all the tutorials on freaktab and read a lot of things on the matter but nothing seems to do the trick. It's really frustrating.
rubbish
resadent said:
We, or at least I, have tried all the tutorials on freaktab and read a lot of things on the matter but nothing seems to do the trick. It's really frustrating.
Click to expand...
Click to collapse
There might be a hardware change for those boxes, the Nexus ROM TV Stock thread has pics on what changed. Best to watch that thread since a solution might be posted soon
I am in the same situation. I tried the sd card burning method and also by the usb cable, but no success at all.
I have got m8s pro+ 2/16gb s905x, The device was purchased on the gearbest website.
some news from my yesterday fight:
sd card burning - many variants of rom, after restart, but on the mainboard there was not observed the reset button, only place named "k1" -> I soldered two points from "k1 place" to make a reset
after that
try by male-male usb cable and usb burning tool 2.0.8, Error result: [0x10105002]Romcode/Initialize DDR/Read initialize status/USB Control setup error
I tried 4 different firmware's, and the same happens every time. Can anyone suggest something?
I can copy whole error if it can help determine the problem.
found on the internet
Romcode / Initialize DDR / Read initialize status / USB Control setup error
-> An error occurs when memory chips do not match. Firmware with ubut for some, but sew on others. It remains to ask the seller about the original firmware: (or shovel (look) available.
resadent said:
We, or at least I, have tried all the tutorials on freaktab and read a lot of things on the matter but nothing seems to do the trick. It's really frustrating.
Click to expand...
Click to collapse
I'm in the same situation!
gearbest give me a link for downloading yhe firmware but that don't work for me :
mega.nz/#F!gqgXwSCa!sFNDXrV_EMzAYAcJ68dV0w
If that can help someone.
Regards,
Cody57 said:
I'm in the same situation!
gearbest give me a link for downloading yhe firmware but that don't work for me :
mega.nz/#F!gqgXwSCa!sFNDXrV_EMzAYAcJ68dV0w
If that can help someone.
Regards,
Click to expand...
Click to collapse
I gave up after 3 days of wasting time with tools and this box... Ordered xiaomi mi box this time.
etemmu666 said:
I gave up after 3 days of wasting time with tools and this box... Ordered xiaomi mi box this time.
Click to expand...
Click to collapse
I will do the same....
i brick mine.....
Any help?
Where can i find *.img file and instruction to brink back in life?
Please help
I can help. My xiaomi mi box has just arrived, after a couple of hours of testing i can say, put that **** (m8s) to trash, buy xiaomi. I am happy that m8s was hard bricked now.
leonkoum said:
i brick mine.....
Any help?
Where can i find *.img file and instruction to brink back in life?
Please help
Click to expand...
Click to collapse
I trie so many roms... without success....:crying:
Cody57 said:
I trie so many roms... without success....:crying:
Click to expand...
Click to collapse
it's not the deal with ROM but with bootloader and recovery. Because it's not working rest of the problems are what box buy now ? Xiaomi or if are rich, nvidia. Screw that chinese scum. Try MI BOX and you'll find that xiomi is the real proffesional android tv (it's quick, responsive and my wife can handle it so it's the best user freiendly commercial )
etemmu666 said:
it's not the deal with ROM but with bootloader and recovery. Because it's not working rest of the problems are what box buy now ? Xiaomi or if are rich, nvidia. Screw that chinese scum. Try MI BOX and you'll find that xiomi is the real proffesional android tv (it's quick, responsive and my wife can handle it so it's the best user freiendly commercial )
Click to expand...
Click to collapse
I have a nvidia shield and I order a xiaomi mi box....
it was just to test a new box and it wasn't too bad.... before testing a new firmware
HELLO the solution for reinstall your rom
hello i have found the solution for you i have received my mecool m8SPRO+ today and i search button recovery
i have found this on freaktab :
You need to press the hidden reset switch (accessed via pinhole on bottom of case) when you connect the USB cable, and it's got to connect to the USB OTG jack, which is the one closer to the power jack.
or see on this video youtube on front panel : xxxxs://XXXX.youtube.com/watch?v=WpThZ2sgkhUt
or maybe same at this video an other place : xxxs://youtu.be/N27pAxtcDSg?t=268
if is not clic take a pinhole if is ok you arrived after bootloader MECOOL ON menu
and take a factory reset
if you don t boot
try method with microsdcard take on sdcard the firmware ota here only the file M8SPRO ota
xxxxs://mega.nz/#F!gqgXwSCa!sFNDXrV_EMzAYAcJ68dV0w
and renom on update.zip
then take power off if is ok you screen apperead with logo android green updating
or do method with usb burning tools
replace xx on web link the correct http
Unbrick the M8S Pro+ 2/16
Hi everyone,
I know how you're guys feel... Is there any new idea or suggestions to unbrick the devices?
After OTA Update the box only shows red and blue at the same time, no boot, no detection of windows with reset button or / with holding the circuit shortcut at "K1".
Can't believe that Amlogic is even worse than the Rockchip boxes to unbrick...
How to factory reset mecool m8s pro plus ? S905w android tv os
Guys i am in trouble with new mecool m8s pro plus ATV i bought..
I am new to xda ..
On the setup
Ipaired my remote
And then connected to my wifi
I then chose the option to put my email and password for the account..it signed in but in the end it was asking for location access i gave it but then i receive an error saying google sign in has stopped
And now i am stuck ..even whei restart box always stuck at the same loop
Guys i dont know what to do...i havent even seen its home screen ..i am in the loop of setting up device
I think maybe faftory resetting it may solve it...but i dont know how to do it ..as i dont know how to open recovery mode...
RCA 10" Touchscreen Tablet PC/DVD Combo Featuring Android 6.0 (Marshmallow)
*No idea why it says PC/DVD as its Android not Windows.
ASIN/Model numbers: ASIN: B077L4VBHK Model: DRP2091
RCA typical RCT number: RCT6603W47M7
Chipset/CPU: MT8127
Ports: 1x Mirco USB (supports ADB! etc. unlike VikingPRO), 1xUSB A, 1xHDMI (mini i believe), 1xMicroSD slot (supports up to 128GB)
Special: 1xDVD/CD Reader/Drive. has unlockable bootloader via fastboot oem unlock
Root Attempts: (Failed: KingoRoot, SRS, KingRoot, RootMaster)
MTK Droid Root & Tools and SP Flash Tools don't seem to work right with this cant create scatter etc. (i assume because of MT8127)
Links:
Walmart/Wally World
Amazon
if any dev could help me root this and get custom recovery would be great.
UPDATE: Thanks to NepoRood (and my testing) theres now CWM recovery (attached to post extract zip and flash img via fastboot flash recovery command.) unfortunately we were still unable to get root access.. if anyone has this device or wants to help root this pm me.
Additional files attached maybe someone can build me cwm or twrp for this as i could never get anything to build for mtk devices.
darkensx said:
Additional files attached maybe someone can build me cwm or twrp for this as i could never get anything to build for mtk devices.
Click to expand...
Click to collapse
I found various firmware downloads, but need to know the exact type of firmware you are running.
Example of one I found: rct6603w47m7-android6.0-v23-v2.15.80 (<-- underlined part is what matters)
If you boot into recovery, it should show you the type of firmware you have.
NepoRood said:
I found various firmware downloads, but need to know the exact type of firmware you are running.
Example of one I found: rct6603w47m7-android6.0-v23-v2.15.80 (<-- underlined part is what matters)
If you boot into recovery, it should show you the type of firmware you have.
Click to expand...
Click to collapse
DRP2091-android6.0-v62-v1.19.90-E02
*also says on very bottom of screen "supported API: 3"
**DRP2091 is rct6603w47m7 not sure why there's so many different model/serial numbers referencing the same exact device...
also i managed to dump the whole device via SP tools readback on linux so if anything beyond recovery or boot img are needed i should have it.
darkensx said:
DRP2091-android6.0-v62-v1.19.90-E02
*also says on very bottom of screen "supported API: 3"
**DRP2091 is rct6603w47m7 not sure why there's so many different model/serial numbers referencing the same exact device...
also i managed to dump the whole device via SP tools readback on linux so if anything beyond recovery or boot img are needed i should have it.
Click to expand...
Click to collapse
That version isn't on the site (or any v1.19.x), I'll download the images from the OP in a bit and see what's inside...
NepoRood said:
That version isn't on the site (or any v1.19.x), I'll download the images from the OP in a bit and see what's inside...
Click to expand...
Click to collapse
Had the same issue also I came across a bunch of ota test files on a Chinese site but links were dead and because no ota update is available i can't grab the ota url or file name. So ended up hitting a dead end.
Would it be possible to bypass the activation code screen with cwm or twrp? Or maybe put a different version of android on the tablet, other than marshmallow.?
darkensx said:
Additional files attached maybe someone can build me cwm or twrp for this as i could never get anything to build for mtk devices.
Click to expand...
Click to collapse
I'm having same problem could someone help me root this tablet explain as easy as possible and slow and clear directions
I have no idea
johnnymack said:
I'm having same problem could someone help me root this tablet explain as easy as possible and slow and clear directions
Click to expand...
Click to collapse
I've got the RCT6603W47M7 tablet, but here in the UK it goes by the name of RCA Neptune 10.1L.
Problem is I have bricked it and I am now trying to recover it using SP Flash Tools. I have tried 2 different stock ROMs, only to have nothing but errors and interruptions during flashing. (errors 2004 and 4008). My tablet is fully charged yet it will randomly disconnect during flashing. I've tried both the MTKAllInOne.bin and DA_SWSEC.bin but I still get the same problem either way.
I've tried different USB ports, different cables and the two download agents that I just mentioned but I am stumped.
I wanted to try the ROM found here https://www.needrom.com/download/rca-rct6603w47m7/
But as I don't have a premium account I cannot access it.
Any ideas? This is very frustrating.
BP9375 said:
I've got the RCT6603W47M7 tablet, but here in the UK it goes by the name of RCA Neptune 10.1L.
Problem is I have bricked it and I am now trying to recover it using SP Flash Tools. I have tried 2 different stock ROMs, only to have nothing but errors and interruptions during flashing. (errors 2004 and 4008). My tablet is fully charged yet it will randomly disconnect during flashing. I've tried both the MTKAllInOne.bin and DA_SWSEC.bin but I still get the same problem either way.
I've tried different USB ports, different cables and the two download agents that I just mentioned but I am stumped.
I wanted to try the ROM found here https://www.needrom.com/download/rca-rct6603w47m7/
But as I don't have a premium account I cannot access it.
Any ideas? This is very frustrating.
Click to expand...
Click to collapse
problem with the cwm recovery if i remember correctly is any thing flashed by it doesnt take the device will just bootloop
i no longer have the device currently i might pickup another at some point... i cant remember if i used the micro usb port to flash or if i had to use a usb male to male cable..
darkensx said:
problem with the cwm recovery if i remember correctly is any thing flashed by it doesnt take the device will just bootloop
i no longer have the device currently i might pickup another at some point... i cant remember if i used the micro usb port to flash or if i had to use a usb male to male cable..
Click to expand...
Click to collapse
Thank you for your reply, I was worried that this discussion was dead. That's frustrating to say the least! Damn! Well, I don't know if this will work but I found another device that is also a MT8127 and has exactly the same spec of this tablet. My point being is that I found a TWRP image for that device, and because it's the same chip set I assume that it'll work for this device too?
If I can get my bricked tablet to even turn on I shall try it. It also makes me wonder that if we were able to root the device, would we be able to access the internal storage by normal means? By using the micro USB ? Either way it'd be great to have it rooted.
I stayed up all night last night trying to flash this tablet and still no luck, it keeps disconnecting half way through.
hi i bought this tablet few weeks ago and i have in my hands for around a week , i'm having some serious issues to use it because the rom basically sucks (continous crash of almost every app, sometimes it reboots by himself etc.)
i wanted to ask if other people have it and if they're facing the same issues , and the most important thing :if there is a twrp and a custom rom to replace this abomination
sorry for my bad english
I received this tablet a week ago and it just restarted once. Not that bad.
I just have another issue: battery charging. Just 3 days ago, I found that the i8 max couldn't be fully charged! Charging stopped at 83% even I plugged in for whole night. I will try the soft-reset tonight and see what happened.
Anyone having similar problem?
snufkin said:
I received this tablet a week ago and it just restarted once. Not that bad.
I just have another issue: battery charging. Just 3 days ago, I found that the i8 max couldn't be fully charged! Charging stopped at 83% even I plugged in for whole night. I will try the soft-reset tonight and see what happened.
Anyone having similar problem?
Click to expand...
Click to collapse
Tried using Power + Vol- but the device kept rebooting. Then pressing Power + Vol+ gave me a boot menu. I selected wipe cache and reboot again ...... no luck. The battery meter stayed at 86% after 8 hours of charging
Seems we need a better rom.
Finally i succesfully unlocked bootloader , flashed a twrp (starting with a xiaomi redmi note 4 twrp i make the porting to make it works on voyo)
And flashed superSU too
But the experience on this tablet still sucks
The firmware from voyo website is not able to flash with sp tools , or twrp so is useless .
If somebody successfully port or create an alternative rom for this tab let us know
antoniob91 said:
Finally i succesfully unlocked bootloader , flashed a twrp (starting with a xiaomi redmi note 4 twrp i make the porting to make it works on voyo)
And flashed superSU too
But the experience on this tablet still sucks
The firmware from voyo website is not able to flash with sp tools , or twrp so is useless .
If somebody successfully port or create an alternative rom for this tab let us know
Click to expand...
Click to collapse
If you could share instructions and files for bootloader unlock and root to the forum, that would be greatly appreciated. Cheers.
Now it's easier
For unlock bootloader you need to download mediatek drivers on Windows and activate usb debug and oem unlock bootloader (or similar) in dev option , from then open a powershell and use adb like other phones
For twrp , google "voyo i8 max twrp" guide and download link are there (i think it s not allowed to post external link)
For root download superSU and flash from twrp
If you need other infos , ask
Sorry for my bad english , it's difficult to write a guide in another language
antoniob91 said:
Now it's easier
For unlock bootloader you need to download mediatek drivers on Windows and activate usb debug and oem unlock bootloader (or similar) in dev option , from then open a powershell and use adb like other phones
For twrp , google "voyo i8 max twrp" guide and download link are there (i think it s not allowed to post external link)
For root download superSU and flash from twrp
If you need other infos , ask
Sorry for my bad english , it's difficult to write a guide in another language
Click to expand...
Click to collapse
Hi. Thanks. My difficulty is actually to find the TWRP file for the i8 Max. Googling it leads you to the GetDroidTips website which gives you a link to the twrp file that is on a Russian forum page. However the download link on that Russian forum page is dead. I tried to contact the writer of the article on GetDroidTips website, but he's not responding. All I want really is a valid download link to the twrp file. Everything else I should be able to do fine from there...
Could someone post the TWRP file someplace...
Once I can load TWRP and root I'll make a backup of the bare firmware and make it available.
antoniob91 said:
Finally i succesfully unlocked bootloader , flashed a twrp (starting with a xiaomi redmi note 4 twrp i make the porting to make it works on voyo)
And flashed superSU too
But the experience on this tablet still sucks
The firmware from voyo website is not able to flash with sp tools , or twrp so is useless .
If somebody successfully port or create an alternative rom for this tab let us know
Click to expand...
Click to collapse
Any chance you could post a link to the TWRP you used. The Russian site no longer has it
Need it too
hs4842 said:
Any chance you could post a link to the TWRP you used. The Russian site no longer has it
Click to expand...
Click to collapse
Hi,
Twrp for Voyo I8 Max
Can someone help please?
Hi all,
I follow Aditya Singh's article to port 3 twrp recoverys for Voyo i8 max.
Installing with SP Flash Tool, I can boot to each recovery of them.
You can choose one of them and I hope it works well on you pad.
* I'm not a pro. Thus, I may NOT provide help for your technical problems. I also NOT sure those recoverys won't damage your pad or data. If you have doubts about this, please do not download them.
Download link: (As a new guy, I can't post any link now. Open it by yourself)
drive.google.com/drive/folders/1DSPQWmFFQlDvPLZUKupo8TpU2dHTueYB
Note:
1. The original twrp recoverys are prepared for Xiaomi Redmi Note4_MTK by cofface and geoanto555.
2. Aditya Singh's article is "How to Port TWRP for MediaTek 64 bit MT67XX Devices!!"
Jacky Lan said:
Hi all,
I follow Aditya Singh's article to port 3 twrp recoverys for Voyo i8 max.
Installing with SP Flash Tool, I can boot to each recovery of them.
You can choose one of them and I hope it works well on you pad."
Click to expand...
Click to collapse
I have the i8 Plus framework file that Voyo has for an i8 reload image. I will try my hand at creating TWRP file and see how they differ. Really need to get my device rooted so I can get the CPU control optimised and to see just how much of the OS is faked by parms in the kernel.
Already had one Octa-Core pad that was actually a dual core hyped up. Lucky for me the guy was in the USA and filed for a refund on it. Only found out after I rooted it and reran tests to really see what was on the inside.
Even so, there are a lot of great reviews about my device. Perhaps I'll try my hand at porting Dirty Unicorn, Remix OS, or Android 8.x.
As is, I'll pay my review after I load the second SIM with my new number.
ADMINISTRATOR: Can we get our own forum group for our device?
Device: Voyo i8 Max
Device code: i8-max
Thanks
Hi bro,
Honestly, I don't figure out what you mean 'cause my English is poor. I guess you wanna find a method to root your i8 plus. I port a twrp for i8 plus with the same method I mentioned.
Again, I don't guarantee that this recovery will not damage your device. You MUST take risk by yourself.
Link: drive.google.com/file/d/1p3RZcLO73-jm1Xm5gdvBwUhoIGHiZFjX
By the way, what do you mean about "ADMINISTRATOR: Can we..."?
Note: twrp recovery comes from following link:
www androidiani com
/forum/modding-vernee-thor/506324-vernee-thor-mt6753-3gb-ram-16gb-flash-modding.html
hs4842 said:
I have the i8 Plus framework file that Voyo has for an i8 reload image. I will try my hand at creating TWRP file and see how they differ. Really need to get my device rooted so I can get the CPU control optimised and to see just how much of the OS is faked by parms in the kernel.
Already had one Octa-Core pad that was actually a dual core hyped up. Lucky for me the guy was in the USA and filed for a refund on it. Only found out after I rooted it and reran tests to really see what was on the inside.
Even so, there are a lot of great reviews about my device. Perhaps I'll try my hand at porting Dirty Unicorn, Remix OS, or Android 8.x.
As is, I'll pay my review after I load the second SIM with my new number.
ADMINISTRATOR: Can we get our own forum group for our device?
Device: Voyo i8 Max
Device code: i8-max
Thanks
Click to expand...
Click to collapse
Worked like magic
thanks a lot
Jacky Lan said:
Hi all,
I follow Aditya Singh's article to port 3 twrp recoverys for Voyo i8 max.
Installing with SP Flash Tool, I can boot to each recovery of them.
You can choose one of them and I hope it works well on you pad.
* I'm not a pro. Thus, I may NOT provide help for your technical problems. I also NOT sure those recoverys won't damage your pad or data. If you have doubts about this, please do not download them.
Download link: (As a new guy, I can't post any link now. Open it by yourself)
drive.google.com/drive/folders/1DSPQWmFFQlDvPLZUKupo8TpU2dHTueYB
Note:
1. The original twrp recoverys are prepared for Xiaomi Redmi Note4_MTK by cofface and geoanto555.
2. Aditya Singh's article is "How to Port TWRP for MediaTek 64 bit MT67XX Devices!!"
Click to expand...
Click to collapse
antoniob91 said:
The firmware from voyo website is not able to flash with sp tools , or twrp so is useless .
If somebody successfully port or create an alternative rom for this tab let us know
Click to expand...
Click to collapse
The file on the Voyo site is for the i8-Plus. I have sent repeated emails to "VoyoJack" and have received no response. I have another email address for him and I will try that way. I have recently tried to review the files and found that the framework is the wrong one. I think Voyo made a mistake in posting it - but it is possible that the same framework loads on both devices. Voyo has yet to confirm this.
The actual .img file is a SP Tools recovery image with scatter. (If you don't know what that means, look up how the SP Tools program works).
hs4842 said:
The framework file, while a .img extension, is actually a zip file with all the ADB pulls of the software. Which makes me think they slapped together something to appease folk like us. But it does contain the boot loader and the scatter files needed to make a working TWRP.
Click to expand...
Click to collapse
Actually the file is a scatter retrieved file that is an entire copy of the i8 Plus framework - that is loaded on i8 Plus and Max (not sure if loaded on PRO). The USA versions of the i8 Max have additional security measures to keep folks from modifying them. Although bootloader unlock programs for other Voyo products seem to work on this device as well.
The device may very well have fake IMEI numbers. The IMEI number does not pass validation. While they will work on most networks, they are still invalid IMEI numbers. Additionally, the serial numbers of these devices are 0123456789ABCDEF - which means they are common hack loads of Android on the device. Even though the device has great performance, the drawbacks of having them work on LTE networks, and overheating of the communications chip are common problems. The overheating causes the device to cut back on communications. Which pretty much sucks if you are trying to play an onlilne game with multiple users.
I have the Voyo i8 Max with two different carriers loaded. AT&T and T-Mobile respectively. It works. It does what I want it to do. However, the fact this has IMEI issues, is darn near almost impossible to root, and has a support system that sucks (zero communications and support from Voyo) should turn away users that are less daring.
Jacky Lan said:
Hi all,
I follow Aditya Singh's article to port 3 twrp recoverys for Voyo i8 max.
Installing with SP Flash Tool, I can boot to each recovery of them.
You can choose one of them and I hope it works well on you pad.
Download link: (As a new guy, I can't post any link now. Open it by yourself)
drive.google.com/drive/folders/1DSPQWmFFQlDvPLZUKupo8TpU2dHTueYB
Click to expand...
Click to collapse
I have confirmed that these files do in fact work. However: A word of caution. I had problems getting my device to boot after installing TWRP. It should be noted that you will have to unlock your boot loader (the Voyo Boot Loader Unlock program for other devices worked for mine too. The Fastboot commands are simple enough to run by hand get the job done). This will wipe your device and reboot.
Since Voyo is a Chinese company, the USA has restrictions on what the device has to employ for security. That includes a trusted, locked bootloader. Once you unlock it your device will display a warning that your device is no longer trusted, and give you a (long) 5 second delay before booting. This will also cause a number of Google services to see your device as not being in compliance.
Translation: You won't be able to watch Netflix on your device....but seriously - Who would want to?? Just load Showbox.apk on it, and Blokada (blokada.org) to kill the ads. (with regards to Blokada - do not load the Mother Of All Ads filter. It will crash blokada)
You must:
1. Install Super User app on your SD Card **BEFORE** you install TWRP. This is the program that cleans up some of the mess the TWRP install leaves behind.
2. Install TWRP via SP Tools. Be sure to backup your recovery.img file before you start (via SP Tools - learn how to use this app before you mess with it)
3. Clear Cache and Delvic cache.
4. Reboot back into Recovery mode
5. Install Super User app. This will clean up the device so you don't get stuck while booting.
At this point you can load and configure your device. Problem is you will not be able to enjoy anything other than GSM speeds (3G) until you fix your IMEI numbers.
***YOU WILL NEED TO DO THE FOLLOWING***
6. The IMEI numbers that ship with the Voyo i8 Max are invalid. Go online to site that has an IMEI Generator and generate a IMEI based on Samsung Galaxy LTE device of your choice. Record two of the numbers down (for SIM1 and SIM2). You'll need these in a moment.
Just be careful that the IMEI number you pick is not a duplicate of someone else's phone or you might get blocked.
7. Use the App Ghost Phone to set the new IMEI numbers. After you have set the numbers, shut your phone off for at least 10 minutes. This will let the network forget your device is 3G. After ten minutes turn your device on and if you have 4G LTE in your range, you will see the 4G icon and either another 4G icon, that means you only have 4G in your area for fastest speed, or 4G and LTE noted for LTE speeds.
After I done this I loaded Androoster and Root Booster to speed my device up even further. Bringing the look and feel of my phablet up to workstation level operations. Installed Viper for Android for added sound features and increase of volume (speaker is very weak on the tablet). Added VPN software, Anti-Virus, and Adaware for near ad free use. Although a lot of ads now are fed by the host server of the app and adware does not block those completely.
I have used my machine for almost two months now and really enjoy it. While the device does not have a GPS, Waze does a good job at ignoring this fact. Google Maps is useless on this device without a good Compass. There exists a kit project for a Bluetooth compass that is reported to work with this device.
Be careful of the type of Bluetooth headphones you choose. I have a mono-speaker Cobra trucker headset. It links well but nothing plays through it except phone calls. For generic mono with mic get a gaming bluetooth cheap headset. Or spend the money for Parrot Trucker headset. For Music, direct wire or find a good over-the-ear set that does Bluetooth very well. Found a $10 set on Wish that did the job so well I bought 2 (one for the Mrs.).
I'm still bugging Voyo for the I8 Max install firmware. The one they have is the i8 Plus SD dump. Doesn't work with our gear, but we can use it as a template for mods if necessary. Particularly with TWRP.
I hope this helps. Please click thanks and keep the good stuff rolling...
Need rom dump of I8 Max
Hello,
I'm new to the I8 Max and have had no joy with Voyo, who do not really seem interested in the foreign markets.
I am very interested in your post and I tried to flash the TWRP recovery but now my I8 Max will not work - it is bricked. I need a rom dump of the system from SP Flash Tool or WwR_MTK_2.40 so I can restore the entire firmware including bootloader. If anybody out there can help, it would be appreciated. MediaTek chips are very robust and as long as I can obtain the original firmware, I should be able to flash back to a working state using SP Flash tool. If someone has the correct firmware from the manufacturer, that would be a blessing. I appreciate any and all help offered.
silver-net-surfer said:
Hello,
I'm new to the I8 Max and have had no joy with Voyo, who do not really seem interested in the foreign markets.
I am very interested in your post and I tried to flash the TWRP recovery but now my I8 Max will not work - it is bricked. I need a rom dump of the system from SP Flash Tool or WwR_MTK_2.40 so I can restore the entire firmware including bootloader. If anybody out there can help, it would be appreciated. MediaTek chips are very robust and as long as I can obtain the original firmware, I should be able to flash back to a working state using SP Flash tool. If someone has the correct firmware from the manufacturer, that would be a blessing. I appreciate any and all help offered.
Click to expand...
Click to collapse
Following FWs are official released. (Replace '|' by '/' and '#' by '.')
Release at 20180223 from Chinese site https:||pan#baidu#com/s/1smg0knN
Release at 20180809 from English site https:||www#dropbox#com/sh/pk4ig0nu2d57oa0/AADFgYJRWA6QD8TP5WXCf4Nna?dl=0
Chinese site http:||www#myvoyo#com/xiazai/anzhou/i8%5FMax/down/
English site http:||en#myvoyo#com/xiazai/V%5Ftablets%5Fseries/i8%5FMax/down/
Hi guys. I just boarded the Voyo i8 max ship so lets see what else we find out.
Mine does have GPS. Google maps locks a location with hardware gps only. I don't use google location services and never will (in any of my devices).
No compass still. That's fine with me and I knew beforehand.
I think voyo does have interest in the overseas market as the device has keyboard and manuals in some kind of English but is not interested in having real customer support (as spected from a cheap China device). No suprises for me there.
Screen is a little unresponsive to touch probably because of the plastic screen protector or because of the 'palm rejection' from the pressure pen compatibility. I won't take the screen protector until the pen arrives... if it ever arrives (bought from Geekbuying).
Scroll is sluggish due to kernel tweaks or something but you can 'fix' it.
Awesome solution to the choppy scrolling: SuperTouch app from the play store. I'm amazed this really worked and no root needed to boot! Honesty don't know how that shlt works but it does. Set it to 500 smooth level because I didn't pay for the full app but damn, I might do as well because the recommended smooth level for this device's specs is more than triple! But you need to pay a few bucks.
Audio suck balls. Mono and as loud as a wishper. It almost makes the job done. I will try to hack the butt out of this device in a couple of monts and try to install real speakers and getting stereo might be a challenge depending of how stupid voyo 'engieneers' were.
Cameras are a joke (as spected).
Screen is nice (probably half the reason we bought this device) but spect bleeeding and quirks. Mine has shadow eyeliner at the right edge.
Keyboard is not worth buying unless at a discount or you really, really need a screen cover. I know I do. Plus point being bluetooth, bad point having the worse back shortcut ever. Home is esc, back is that mac flowr thingy + tiny ass backspace and recent apps...kinda shortcut is alt+tab. Alt+F4 is impossible to do with this keyboard.
The experience of the typing. Its usable, better than touch typing the screen while sitting on the desktop, but way worse than using swype, swiftkey or google board gliding. Still a pain because its like typing in a remote control.
It attaches to the device pretty poorly. It preffers to attach to the front of the device.
Unlike the voyo i8 pro this one has google play working out of the box.
Wifi is poor at medium range and unusable at long range. 2.4ghz. Haven't testet 5ghz.
4G is unavailable to me as my carriers only use B2 and B4 which this tablet doesn't support (haven't put a SIM yet but will in a couple weeks).
The pen... buttons don't work according to everyone. I can't tell, mine was never shipped.
That's all so far. I have had this device for almost an hour.