Lollipop 5.0 Echoe rom, fro i9505
Download
Download from echoe rom wesite
or
https://mega.co.nz/#!mwA32BZD!ay3Rf_u0G7891xwyAv58De2ot4X50xe8sZtF50hXLNk
Installation
Device : GT-I9505
Download the ROM from the link above
Reboot in Recovery
Wipe Data / Factory Reset
Select "Install zip from SDCard"
Reboot system
If you have custom rom installed previously, please download and flash stock room using odin
Credits to : developer Echoe Rom
thanks
Mod Edit links removed
First of all Thanks @ROM-HUAWEI
I guess you have linked @mygalaxya TWRP 3.0.0-0 for Samsung Galaxy A3 with this TWRP you can Flash atm nothing with the FU Device until @mygalaxya CM13 is Ready because
mygalaxya said:
Hi, this new TWRP 3.0 uses different mount points than 2.8.7.0, on the build you are trying to flash it uses old mount points. The developer you made the ROM must now use the mount ext4 "dev/block/bootdevice/by-name/system" on META-INF, otherwise you will not be able to flash the ROM. I will update all my builds to support this new mount points.
Click to expand...
Click to collapse
and we get no response from @evilracer123 if he Update his ROM and is has also Reboot bugs so atm is TWRP 2.8.7.0 for Samsung Galaxy A3 more usefull for the most users.
I wished i found your Thread yesterday because i made a Noob friendly instructions guide in @evilracer123 CyanogenMod 12.1 for Samsung Galaxy A3 Thread
btw. if you use the Odin3 from the CF-Auto-Root zip it is so configured as you described and is has only the AP/PDA Button working (Noob friendly) you can Flash also TWRP and Stock ROM´s with it
Introduction
This is a CWM based recovery and I did put up some work to update it to lollipop (cm 12.1) and marshmallow (cm-13) after official cwm development stopped at kitkat. It works with LOLLIPOP and MARSHMALLOW kernels and it builds with cm 12.1 or aicp lp-5.1 (version 5.2) and with cm 13 or aicp mm-6.0 (version 6.1).
Click to expand...
Click to collapse
Features
- EXT4 and F2FS if you need it.
- full touch menu ported by me from PhilZ touch Recovery. The old Napstar-xda touch module was good but it's quite old and to update that was too much work. Actually There is a version 4 with that touch module, all working, but the touch doesn't work with some input drivers and I had to give up on it for the new and improved version from PhilZ.
- all cwm functionalities are up and working (adb, sideload, backup, restore, install, mass storage...). There is no mtp and if your phone doesn't have an external sdcard you can't connect it to PC while is in recovery mode. But there is usb-otg support, of course if your phone was shipped with that.
- added new menu for backup and restore advanced, to use it for backing or restoring only a specific partition and I also ported from PhilZ the multizip flashing function.
Click to expand...
Click to collapse
Installation instructions
You must be on AOSP ROM or any ROM with LP kernel!!!
After downloading aosprecovery5.1.1.img, rename to recovery.img.
Install Flashify or Rashr and flash the recovery.img
Downloads
https://www.androidfilehost.com/?fid=24588232905719935
Credits
Phil3759
TWRP developers
Clockworkmod Team
Cyanogenmod Developers
AP756
DerTeufel1980
XDA:DevDB Information
CTR LP, Tool/Utility for the Android General
Contributors
kirito9, carliv
Source Code: https://github.com/kirito96/device_Alcatel_4032
http://forum.xda-developers.com/android/software/recovery-carliv-touch-recovery-v5-1-t3389290
Version Information
Status: Stable
Current Stable Version: 5.7
Stable Release Date: 2016-07-10
Created 2016-06-25
Last Updated 2016-07-10
Update
CHANGELOG 05-07-2016:
- fix loading the graphical ui for qcomm devices;
- added cancel backup feature (use power button or select from virtual keys);
- fix display of progress while backup, restore or install;
- some other small fixes and improvements (you can check the github commits).
Click to expand...
Click to collapse
Link- https://www.androidfilehost.com/?fid=24588212152304966
Hi all
am new here with little bit confusion. help me to install new stable android version
which ROM,gapp,recovery can use for best performance in Samsung galaxy grand 2 duo
Guide
Assuming You Are on Stock KitKat (4.4)
Recovery :-
TWRP 3.0.0 (aapav01).
ROM :-
Motion ROM LL[TW][5.1.1][PORT TW] (aapav01). , CyanogenMod 13 for Galaxy Grand 2 (adiyataupreti). ResurrectionRemix 5.7.4 MarshMallow (adiyataupreti) [My Daily Driver]. , CyanogenMod 13.0 (soUnd001).
Kernel :-
[5.x/TW/6.x]Infected Kernel R4 (neonkat). , [TW-5.1.1] SkyKernel LL Kernel (soUnd001).
Gapps :- Nano - Micro Gapps (6.0.1 ROMS)
Steps :-
1- Flash TWPR using Odin (PDA/PA) (READ TWRP OP] {LINK ABOVE}
2- Download any Custom ROM and Place on External storage
3- Flash The Downloaded ROM using TWRP ( power - action - volume up) [Read ROM OP] {Links above}
4- Reboot
5-Use ROM For 10 minutes and Reboot Again
6- Optional :- Flash Gapps (Not Needed For TW Ported)
Flashing Kernels :-
1- Download Your Wanted Kernel.
2- Place on External Storage.
3- Flash Using TWRP
4- Reboot
Improve Performance :-
Lspeed (paget96). , Kernel Aduitor (garak)
Hi everyone. Today I have good information for J1 (J100H) users.LineageOS port is available, look...
1.Root Samsung Galaxy J1
2.Flash TWRP recovery
3.Backup stock android
4.Install LineageOS 11
Here, you can see full specification:
Display: 4.3"
Resolution: 400x800
Android: KitKat 4.4.4 (TouchWiz)
Internal Storage: 4GB up to 256GB with SD Card
RAM: 512MB
CPU: Dual-Core 1.2GHz Cortex A7
Chipset: Spreadtrum
GPU: Mali-400
WiFi: Yes
Bluetooth: Yes
Camera: Primary: Yes [5MP,Led flash,[email protected]]
Secondary: Yes [2MP]
Battery: Li-Ion 1850mph
USB port: Yes - MicroUSB
3.5mm: Yes
Before we start, I must say thanks to two XDA users:
1. @turbolukex5 [He made this awesome rom]
2. @CTXz [He made TWRP recovery for this device]
So...
This is a step by step guide, so follow all steps and you will not have any problems...
I'm not responsible if you make some mistakes and brick your device!!!
1. Root Samsung Galaxy J1 (This is not necessary!)
- Download KingoRoot for Windows
- Install program
- In settings of your device enable USB Debugging
- Connect your phone to PC via USB cable and wait
- After rebooting, your phone is rooted
- Download SuperSU and Root Checker and check the status of your phone
- That's it, you have a rooted device
2. Flash TWRP recovery
- Download .zip file from the link down
- Unzip files to desktop
- Then you will see Samsung G J(1)000H folder
- Open Samsung USB drivers and install it
- Then copy TWRP recovery.tar to desktop
- Turn off your phone and go to download mode [VolumeDown + Home Button + Power Button]
- In menu select "Continue" [VolumeUp button]
- Now you can connect the phone to the computer via USB cable
- OK, now you must run Odin [Make sure your device is recognized]
- Click on AP and find TWRP recovery.tar
- Now click start and wait until it's done
- Congrats, you have TWRP recovery
3. Backup stock android
You must have an SD CARD for this
- Reboot to recovery
- Go to the Backup section
- Select: Boot, Cache, Data, and System
- This file is large so you must have SD Card [4GB is minimum]
- Now tap on Storage and select SD Card
- And that's it, just swipe to backup and wait
4. Flash LineageOS 11
- Download LOS from the link down
- Put LOS on SD Card
- Reboot to TWRP [VolumeUp + Home Button + Power Button]
- Now go to the Wipe section
- Select Advance wipe
- Then select: Dalvik Cache, System, Data, Cache
- Now Swipe to Wipe
- Now go back to the Install section
- Select SD Card and find LOS 11
- Swipe to Confirm Flash
- Congrats, you have LOS 11 on your device
Guys, that's all, if you have some questions just ask.
Hit the thanks button, it's free
Links: [2020 Update]
1. Official Therad: >>>
2. TWRP Recovery (by CTXz): >>>
2. Root Checker: Download
Just to note. Oem unlock in settings isn't required as it's not an option that is available on j100h
turbolukex5 said:
Just to note. Oem unlock in settings isn't required as it's not an option that is available on j100h
Click to expand...
Click to collapse
Thanks!
LineageOS 11 Builds:
!!!
Check the official thread for links
Changelog:
In build 1...
Version: Alpha
Fixed: -----
Bugs: Tourch,Recent button,SIM,
Info. First release
In build 2...
Version: Alpha
Fixed: Tourch,Recent button,SIM
Bugs: Computer can't recognize the device as MTP
In build 3...
Version: Beta
Fixed: MTP
Bugs: ---
In build 4...
Version: Beta
New: LineageOS - Skin (Pt. 1) - Boot animation - Launcher3
Bugs: Skin is broken
In build 5...
Version: Final
Fixed: LienageOS Skin
New: LineageOS - Skin (Pt. 2) - CM strings in the OS are replaced with LOS strings
Bugs: ---
Info. On the official thread you can download ROM for dual-sim J100H
ROM Informations:
Developer: turbolukex5
Realse date: 29.04.2016
ROM OS: LineageOS 11
OS Version: Android 4.4.4 KitKat
Last build: 02.04.2017
Status: Stable | Discontinued
Official Thread: Here
thanks
Hi. thanks bro. its great!
Ali_MZ said:
Hi. thanks bro. its great!
Click to expand...
Click to collapse
Thanks for feedback!
Please hit Thanks button to support me!
Oh sorry,I already have Thanks from you!
StefanBuljic said:
New build of Cyanogenmod 11 [LineageOS] is here!
By turbolukex5!!!
Information:
Build 1: 2016.04.29 Download
Build 2: 2017.03.22 Download
Bulid 3: 2017.03.25 Download
Bulid 4: 2017.03.25 Download [Don't download this build!]
In build 2...
Version: Alpha
Fixed: Tourch,Recent button,SIM
Bugs: Computer can't recognize the device as MTP
In build 3...
Version: Beta
Fixed: MTP
Bugs: ---
In build 4...
Version: Beta
New: LineageOS - Skin (Pt. 1) - Boot animation - Launcher3
Bugs: Skin is broken
If you want to help turbolukex5 look this: [by turbolukex5]
"I'm looking for people to update system apps for my new Lineage Skin Please PM me if interested!"
Click to expand...
Click to collapse
Any plans for Marshmallow & Nougat ?
rishiud said:
Any plans for Marshmallow & Nougat ?
Click to expand...
Click to collapse
Wouh,easy...
J1 can't run 6.0 or 7.0
He have only 512mb of RAM,so port 6.0 on this device is impossible
Lollipop maybe
StefanBuljic said:
Wouh,easy...
J1 can't run 6.0 or 7.0
He have only 512mb of RAM,so port 6.0 on this device is impossible
Lollipop maybe
Click to expand...
Click to collapse
Okay thanks
rishiud said:
Okay thanks
Click to expand...
Click to collapse
Always
where can i find xposed and its uninstaller
ad. said:
where can i find xposed and its uninstaller
Click to expand...
Click to collapse
For LineageOS or for stock rom?
For stock ROM:
https://mega.nz/#!MdkmjSgL!7cQPTQWkywWWobSBG5RI_PFijnrZARBOG1CzW92LF1Q
Info.
Developer: SolarWarez
Date: 29.11.2015
Status: Stable
Version: 2.6.1
Supported android: KitKat 4.4.4
For LineageOS I don't know
This Xposed working on stock rom 100%
StefanBuljic said:
For stock ROM:
https://mega.nz/#!MdkmjSgL!7cQPTQWkywWWobSBG5RI_PFijnrZARBOG1CzW92LF1Q
Info.
Developer: SolarWarez
Date: 29.11.2015
Status: Stable
Version: 2.6.1
Supported android: KitKat 4.4.4
For LineageOS I don't know
This Xposed working on stock rom 100%
Click to expand...
Click to collapse
Thanks
ad. said:
Thanks
Click to expand...
Click to collapse
Nothing my friend,I'm here to help!
And,IF YOU CELEBRATING,happy easter!
I need backup of contact storage app for J100HDDU0API1.
Nocturnal_Creature_137 said:
I need backup of contact storage app for J100HDDU0API1.
Click to expand...
Click to collapse
For stock rom?
Ok,I will leave link very very soon
StefanBuljic said:
For stock rom?
Click to expand...
Click to collapse
Yes ... for stock ROM... and THANKS.