hi guys I'm new in the forum,
I have a problem whith my LG F60(D390N) , it's bricked,(I had installed the wrong custom ROM) now I can't go to recovery or download mode ,
the phone don't start up , (there's no problem whith the battery or charger,
when I connect the phone to the PC i see only QHSUSB_BULK, please guys help me :crying: ,
the assistence it's very expensive.
Im in the same boat.
Installed first a stock 5.0.1 over the kitkat, everithyng went fine but after that installd a wrong CWM recovery
Now when I turn on my phone, its vibrate infinitely, and nothing happen. Black screen. When I put in-out-in my usb cable, screen turns on, and phone says: DBI Apps Watchdog Reset!
DemiGod Crash Handler : DBI Apps Watchdog Reset!
Please do following action.
1) Dload Mode. Please connect USB.
2) Get the ram dump image using QPST Configuration.
----------------------------------------------------------------------------
Board Info
rev. : 1.1, serial : 003bwff********
secure boot : disabled
--------------------------------------------------------------------------
Jump to Dload Mode.
I have no idea how I can take it back into life :S
I find it in device manager at COM ports : LGE AndroidNet USB Serial Port (COM6)
and at modems : LGE AndroidNet USB Modem
Related
I flashed custom recovery image successfully and after that, when phone has to restart, it just stuck at LG logo.
When I tried to enter in custom recovery menu, but it shows only LG logo.
I tried to connect with PC, but it was unsuccessfully. The PC doesn't recognize the device. (nothing happens).
Can anyone help me?
This happened to me also. I solved it like this:
First thing to do is get sure the LG drivers are installed ( there is a topic in the forum on this also).
Install KDZ ( serch in the forum and download it)
Download a room ( stock or not )
Flash the phone with KDZ ( after the drivers have been installed the phone should be detected on the pc.
After flashing if it does not start up do not fear, get the battery out, re install the battery and do a hard reset power+home+volume down buttons pressed at the same time and it should work.
If its your first time install Stock GB 20E as it is an open room, if not new to this I would suggest CM7.
Hope it helped
Regards
But the PC doesn't recognize the phone.
Here is the log from KDZ:
[R&D Test Tools Log File]
23:47:37 : Launching SW update
23:47:37 : Unpacking KDZ
23:47:39 : KDZ file extraced
23:47:40 : Files were extracted.
23:47:40 : LGMobileDL Load.
23:47:40 : Port = -1
23:47:40 : Connecting to phone
23:47:40 : PHONE WAS NOT FOUND!
23:47:42 : ===FINISHED===
Click to expand...
Click to collapse
How should I solve this problem? :/
bondzi said:
But the PC doesn't recognize the phone.
Here is the log from KDZ:
How should I solve this problem? :/
Click to expand...
Click to collapse
I had this same issue too, do not worry.
Keep your phone plugged into your computer, and go to Start > Control Panel > System > Hardware > Device Manager > Modems and disable the LG modem.
I am on Windows XP, so it may not be the same steps, but the point is that you have to disable the LG modem in Device Manager.
I had the same problem as well at one point. What operating system are you running on your computer?
I had the same issue, but I could not find the LG modem to disable it, it was just that windows was not detecting my phone at all, or using the drivers I had installed for my P500 to figure out what was connected to my laptop. Bricked phone after a failed ROM flash. Reinstallation of USB drivers for my phone failed to do anything.
Have you used LG Mobile update at all? I got all my drivers through it, rather than useless PC Suite 4.
Download it through HERE
Here's what I did to rectify it (Running windows vista):
DO NOT PLUG IN YOUR PHONE UNTIL STEP 3!
1. Went to system restore in windows(you'll find it under Backup and Restore in the Control Panel) and restore your computer to a state before installing any drivers for your phone.
2. After everything had completed, installed LG Mobile update. There is an option to install general USB drivers for your phone, DO NOT do it! Go to Customer Support > Application, Manual & USB driver download. Input your IMEI number from behind the battery in the back of your phone(or just select the "Read your phone" option if you can get it to read your phone). It will search and return the correct drivers for your exact phone. Download and install your USB drivers.
3. Keep your phone disconnected from your PC, and start up LG mobile update again. Connect your phone, LG mobile update should verify the connection by trying to connect to your phone, checking software versions, etc. It will connect even if you are stuck at the LG screen.
4. If everything checks out run KDZ updater and flash your phone back to original specs.
hey first go to emergency mode by pressing back(return) and volume up
and then in emergency mode use kdz it then only pc will recongnise your phone
believe me this thing also happens with me and I know that time I very scared
that time I used this article
http://forum.xda-developers.com/showthread.php?t=1015332
bondzi said:
I flashed custom recovery image successfully and after that, when phone has to restart, it just stuck at LG logo.
When I tried to enter in custom recovery menu, but it shows only LG logo.
I tried to connect with PC, but it was unsuccessfully. The PC doesn't recognize the device. (nothing happens).
Can anyone help me?
Click to expand...
Click to collapse
read general thread it has been answered many times,stucking at lg logo is solved by take out battery reinsert and the 3 button combo
have u tried HOME + VOL DOWN +POWER BUTTON,still if it dont,
read downgrading details here http://forum.xda-developers.com/showthread.php?t=1038338
error guide here http://forum.xda-developers.com/showthread.php?t=883314
The same problem. But i solved it.
1) install again the driver using B2CAppSetup
2)This is based by xda forum by: Zecanills with a detailed explanation from my side.
- You need to download the firmware of your device. Download "Orginal LG Firmware" application (search in xda forum). Open it, put your IMEI and you will download the original ROM.
- Download KDZ updater and uncompress it
KDZ_FW_UPD_EN.zip - 4shared.com - online file sharing and storage - download
- Install msxml.msi from the uncompressed directory
3) Remove the battery, put it back and start the phone in emergency mode (actually the only way possible) back+up volume+power
Connect your device and run KDZ_FW_UPD.exe (as administrator). If the phone is not recognized repeat step 3) several times.
Select Type : 3GQCT
Select PhoneMode : DIAG
In KDZ file : Choose the ROM file you downloaded in the step 2)
Press Launch software update and wait (It will be 10 minutes or so).
Wait until it reboots.
After reboot will appear an image as in the following link: http://androidforums.com/getitnowmarketing/330813-all-one-recovery-thread.html
Don't worry. Restart phone again pushing power button (or remove battery, put it back and push power ) and then after few minutes you will have the phone as the begging when you bought it.
Thanks people for helping me. I just put the phone in emergency mode (Volume UP button + Home button), connected to the PC and flashed with KDZ.
After that, the phone works fine.
Thank you again!
bondzi said:
I flashed custom recovery image successfully and after that, when phone has to restart, it just stuck at LG logo.
When I tried to enter in custom recovery menu, but it shows only LG logo.
I tried to connect with PC, but it was unsuccessfully. The PC doesn't recognize the device. (nothing happens).
Can anyone help me?
Click to expand...
Click to collapse
man i am new as this thing
my lg is p925 and i didnot know that after i install root kdz for p920 and when i run rom maneger i did not find my model lg p925 so i tryed the res of the lest in rom maneger
bad move..........one of them is about lisen or somthing like that....but when i restart my phone frezzzz in lg logo ...i went to recovery mode (vol dwn+power)and all list about wiping no install zip in sd so i tryd (vol up+connect to pc) works so i use lg update an it says i have last apdate then i tryd cs>recovery with imei number but it says model not spport s/w....what must i do..dose flash it will hilp me? plzzzzzzzzzzzzz hilppppppppppp
LG P925
Same thing happened to me! I'm desperate... I've done research for hours and tried everything but no success so far... anyone could help us?
88prince said:
man i am new as this thing
my lg is p925 and i didnot know that after i install root kdz for p920 and when i run rom maneger i did not find my model lg p925 so i tryed the res of the lest in rom maneger
bad move..........one of them is about lisen or somthing like that....but when i restart my phone frezzzz in lg logo ...i went to recovery mode (vol dwn+power)and all list about wiping no install zip in sd so i tryd (vol up+connect to pc) works so i use lg update an it says i have last apdate then i tryd cs>recovery with imei number but it says model not spport s/w....what must i do..dose flash it will hilp me? plzzzzzzzzzzzzz hilppppppppppp
Click to expand...
Click to collapse
Hi
I flashed the phone with invalid firmware using SP_Flash_Tool.
Now SP_Flash_Tool and Windows doesn't see the MT65xx Preloader USB device after disconnecting/reconnecting the battery.
The phone doesn't switch on.
Is possible to recover a preloader on MTK6577 (Zopo ZP 900) using the flex cables or other methods?
Thank you
I have same situation. Did you find any solution for this?
Hi all,
I accidentlly wipe preloader on my Lenovo P770 and computer identify it as "alcatel single rndis interface #2". Is there any possibility to restore preloader in my phone or it is comlete brick?
I would be very thankful for any help.
Lenovo P770 preloader wiped
my preloader accidentally wiped by my son, now my prealoder appears as ALCATEL.
I can't turn on my phone. Any ideas what to do?
when i install MTK Preloader / Usb driver, when i put the phone and usb on the computer it will disconnect after a few seconds, and connect and disconnects again.
The problem also appearing when i am flashing the phone with FLASHTOOL. That's why i am not able to flash my phone...
Kindly please help me out...
Any idea to help me regarding this problem would be a great help...
Thanks in advance...
Hi there...I am also facing the same problem in my mtk device...I could flash the stock rom from SP flashtool...but after flashing my phone is in dead state...Any Leads..???
I got to the same problem with my phone. There is no chance to turn it on.
Someone has got a suggestion?
Same problem.
We hope that one hero appears here
i will pay for the solution!
MTK6577 Tablet
Hey guys .. any solution ?
Lenovo A2107A-H, Dual SIM dead after SP-Flash
I stand in a row with you all, I also have killed my tablet with SP-Flash, It appears as Alcatel Single RNDIS Interface in Win7 control panel's network adaptors and in Win8.1 as "unknown device". I already uninstalled the drivers, the Win7 needed to reboot after that, but re-installed the same sh** after reconnecting. I have heard about another tool, not SP-Flash, which shall be able to "find" the tablet on the USB bus, but I don't remember the name.
How to un-brick Lenovo P770!
lystor said:
Hi
I flashed the phone with invalid firmware using SP_Flash_Tool.
Now SP_Flash_Tool and Windows doesn't see the MT65xx Preloader USB device after disconnecting/reconnecting the battery.
The phone doesn't switch on.
Is possible to recover a preloader on MTK6577 (Zopo ZP 900) using the flex cables or other methods?
Thank you
Click to expand...
Click to collapse
I un-bricked my Lenovo P770 yesterday!
How to do this:
1) Download and install "MT6577 USB VCOM drivers" -drivers for your phone
2) Open Device manager in your computer. Then "View" and "Show hidden devices" (do not close Device manager)
3) connect your phone to PC by USB cable (without battery, some phone with battery)
4) In device manager, in Network adapter (in my situation, after few second) shows "Alcatel single rndis interface #. . ." - it can appears and disappears!
5) When "Alcatel single rndis interface #. . ." appears click on this device Update drivers->Browse my computer...->Let me pick.. and here you should see "Mt65xx Preloader" if not you should find your driver.
6) When you update this driver you could use Flashtool v3->loading scatter file (you can find your android on needrom website. for example: P770_ROW_S110_130204_707WOW) -> check only PRELOADER and click Download
then connect your phone again to USB (without or with battery) and wait some seconds.
GoodLuck!!!
You can control on needrom website
I have the same issue. mediatek S8 - mt6577 7inch tab
Hello
Last week I became my Star x26i. Its quite a very good phone, but because of WiFi and Battery issues i tried to update it to a newer version, like in this tutorial :
http://forum.xda-developers.com/showthread.php?t=1680338
So I used a program, calles SPmultiPortFlashDownloadProject
Everything went fine, but after the program erased the emmc Windows tried to install a new driver and failed. The program stopped and now the phone cant boot anymore (understandable with an formatted eemc...) The Pc detects the phone anyway, first as an unknown device and after installing a new chipset driver as "MediaTek DA USB VCOM Port (COM6)" If I try to reflash with the same program it gives me following issue like on this picture: http://imageshack.us/f/856/erroroly.png/ (Error: No Bootrom USB Port was found! COM6 is not a Bootrom (preloader) USB Port. Auto polling Number0.
Are there any Chances to rescue this device or is it totally bricked? Thanks in advance...
Hey,
I have been years just reading these forums but never made any posts, so thats why I cannot post to development section anyways. I happened to totally brick my phone by flashing wrong preloader into it. However this morning i succesfully reflashed it and now I have somehow working phone (just need to find new rom now) but anyways. This thread is to help other people who has semi bricked their phones as well.
Current situation.
-Phone doesn't charge,
-Phone doesn't turn on (nothing happens)
-Computer sees phone for few secs, so you have "META mode" access. If your computer doesn't see your phone at all make modified USB connect the 4pin to ground. This is what I did actually. If that doesn't work you can google for test points.
My device:
MTK6575 (Fake mt6589)
512MT RAM (fake 2GB)
800x460 resolution (fake 1920x1080)
4GB internal memory (fake 8gb)
5" screen
2200mah battery (fake 3000mah)
OK this is the prodecure that got my phone back to live!
Install windows XP (Yes, windows 8 didn't work for me. most likely drivers are not ready for it. I will not write steps how to install windows xp)
Install USB deview
-Google it, download it, extract package and run it
-Remove all drivers related to Mediatek, android, usb vcom etc.
Download and install VCOM USB Drivers
-Download these drivers http://www.mediafire.com/download/31nddwqdot5ajp2/MT6575+USB+VCOM+drivers.zip
-Put your phone battery in (50% charge) required. wait 10s. Take battery off and connect your phone to PC as meta mode ( modified USB cable, VOL+/- while connecting, you can read more about this from here: http://forum.xda-developers.com/showthread.php?t=1943442
-When your phone is connected it will disconnect after ~3-5seconds. Now you have to wait in device manager connect the phone right click the device when it shows up. Install driver from the location where you unpacked your VCOM USB drivers/2K_XP_COM/ dont automaticly install them but manually. After windows have found drivers UNTICK show compatible devices. And MANUALLY select preloader driver. Now it will install it the next time the device connects. OK now we have Preloader driver in place. Notice that we will install one more driver later needed in flashing procedure. Disconnect phone.
Now download compatible rom. for me My backup was not working, but this rom worked out perfectly:
http://search.4shared.com/postDownload/wILsUT7J/MTK6575_S4_FLASH_TOOLS_YEDEK.html
Download SP Flash Tool v3.1222.00, extract it.
Ok lets recap what we have now:
-preloader drivers
-phone disconnected
-SP Flash Tool v3.1222.00
-back up we can use to flash
Open flash tool, enter scatter file and go to Format
-Select Format whole flash except bootloader and nvram bin region. -> connect phone -> succeed
-Select Format NVRAM bin region ONLY -> connect phone -> succeed
-Select Format whole flash -> connect phone -> succeed
Ok. Next we need to flash compatible rom this part is tricky. Read before doing anything.
-Disconnect your phone, enter battery (50% charge required)
-wait atlaest 15seconds, and remove battery
-(I dont know why those steps were required, but didn't work without it)
-Open SP Flash tool select scatter file and select all checkboxes
-press download
-connect your phone in META mode with Preloader drivers we installed before.
-Now red prograss bar will start going and phone will disconnect After it reconnect We want ANOTHER drivers are located in the same place but now we need to select Mediatek DA Vcom USB drivers. If everything went fine you get yellow progress bar and it will reflash your phone! :victory:
In the last part if you got Error 5054, This is good. It means your phone is still alive! but your current preloader does not match the data you are going to flash. So you need to go back to google and download other rom try flashing everything (thats what I did, before hitting jack pot, eventually you will find compatible rom)
If you got ERROR 3002 switch back to SP Flash Tool v3.1222.00 newer one doesn't work!
I got some other errors as well when flashing and I solved them but didn't write down the errors so I cant remember them sorry
Remember before connect phone as META mode. Plug in battery with atlaest 50% power wait 15s. remove it. and connect the phone to PC. This was the mysterious step I was missing when struggling with this 5 days!
By the time of writing this article I got my phone working rom, everything works.
GOOD LUCK
ps. Sorry for typos.
:angel: kthxbai
thanks!
AND THANKS FOR yuweng and rui1 who made this all possible!
anyway now I'm back to porting CM to our device. hopefully this helped somebody (and yes, I will be more careful this time)
Hi, it worked for me and i could unbrick my mtk6575
Hi, there
rom given in post worked for me
and i could finally unbrick my phone, but now it asks for the password to decrypt storage after boot. I don't know what to do.
please provide password or any solution to it.
my device is stuck on boot?
Havunen said:
Hey,
I have been years just reading these forums but never made any posts, so thats why I cannot post to development section anyways. I happened to totally brick my phone by flashing wrong preloader into it. However this morning i succesfully reflashed it and now I have somehow working phone (just need to find new rom now) but anyways. This thread is to help other people who has semi bricked their phones as well.
Current situation.
-Phone doesn't charge,
-Phone doesn't turn on (nothing happens)
-Computer sees phone for few secs, so you have "META mode" access. If your computer doesn't see your phone at all make modified USB connect the 4pin to ground. This is what I did actually. If that doesn't work you can google for test points.
My device:
MTK6575 (Fake mt6589)
512MT RAM (fake 2GB)
800x460 resolution (fake 1920x1080)
4GB internal memory (fake 8gb)
5" screen
2200mah battery (fake 3000mah)
OK this is the prodecure that got my phone back to live!
Install windows XP (Yes, windows 8 didn't work for me. most likely drivers are not ready for it. I will not write steps how to install windows xp)
Install USB deview
-Google it, download it, extract package and run it
-Remove all drivers related to Mediatek, android, usb vcom etc.
Download and install VCOM USB Drivers
-Download these drivers http://www.mediafire.com/download/31nddwqdot5ajp2/MT6575+USB+VCOM+drivers.zip
-Put your phone battery in (50% charge) required. wait 10s. Take battery off and connect your phone to PC as meta mode ( modified USB cable, VOL+/- while connecting, you can read more about this from here: http://forum.xda-developers.com/showthread.php?t=1943442
-When your phone is connected it will disconnect after ~3-5seconds. Now you have to wait in device manager connect the phone right click the device when it shows up. Install driver from the location where you unpacked your VCOM USB drivers/2K_XP_COM/ dont automaticly install them but manually. After windows have found drivers UNTICK show compatible devices. And MANUALLY select preloader driver. Now it will install it the next time the device connects. OK now we have Preloader driver in place. Notice that we will install one more driver later needed in flashing procedure. Disconnect phone.
Now download compatible rom. for me My backup was not working, but this rom worked out perfectly:
http://search.4shared.com/postDownload/wILsUT7J/MTK6575_S4_FLASH_TOOLS_YEDEK.html
Download SP Flash Tool v3.1222.00, extract it.
Ok lets recap what we have now:
-preloader drivers
-phone disconnected
-SP Flash Tool v3.1222.00
-back up we can use to flash
Open flash tool, enter scatter file and go to Format
-Select Format whole flash except bootloader and nvram bin region. -> connect phone -> succeed
-Select Format NVRAM bin region ONLY -> connect phone -> succeed
-Select Format whole flash -> connect phone -> succeed
Ok. Next we need to flash compatible rom this part is tricky. Read before doing anything.
-Disconnect your phone, enter battery (50% charge required)
-wait atlaest 15seconds, and remove battery
-(I dont know why those steps were required, but didn't work without it)
-Open SP Flash tool select scatter file and select all checkboxes
-press download
-connect your phone in META mode with Preloader drivers we installed before.
-Now red prograss bar will start going and phone will disconnect After it reconnect We want ANOTHER drivers are located in the same place but now we need to select Mediatek DA Vcom USB drivers. If everything went fine you get yellow progress bar and it will reflash your phone! :victory:
In the last part if you got Error 5054, This is good. It means your phone is still alive! but your current preloader does not match the data you are going to flash. So you need to go back to google and download other rom try flashing everything (thats what I did, before hitting jack pot, eventually you will find compatible rom)
If you got ERROR 3002 switch back to SP Flash Tool v3.1222.00 newer one doesn't work!
I got some other errors as well when flashing and I solved them but didn't write down the errors so I cant remember them sorry
Remember before connect phone as META mode. Plug in battery with atlaest 50% power wait 15s. remove it. and connect the phone to PC. This was the mysterious step I was missing when struggling with this 5 days!
By the time of writing this article I got my phone working rom, everything works.
GOOD LUCK
ps. Sorry for typos.
:angel: kthxbai
Click to expand...
Click to collapse
my rooted mt6575(spice mi-315) device stuck on boot logo. i also tried clar cache and wipe all data bt still same boot logo appear . i am going to ur theard when i format whole flash except bootloader and navram. and connect my device to pc and error occured.....
does some know where to find a latest rom for my mtk 6575(samsung glx,y grand duo hard copy) plz i really need 1
google play service was not working so i uninstalled it to intall a proper vrsion but when i try install it from google play store it says imcompatible with same shared id what can i do plz hlp me coz some of my apps and game r not working...
gapps and cwm problems
soulindub said:
google play service was not working so i uninstalled it to intall a proper vrsion but when i try install it from google play store it says imcompatible with same shared id what can i do plz hlp me coz some of my apps and game r not working...
Click to expand...
Click to collapse
Quote:
Originally Posted by Snekhers
I need this informations roms!
Screen : 540x960
BB Chip : MT6577
Ms Board : Glaxy S3
IMEI1 : XXXXXX
IMEI2: XXXXXX
Modem Ver. : MAUI.11AMD.W11.50.SP.V12. 2012/09/20 18:56
Bar code : 030801050804260123456788.81_20390210
Build Time : 2012 10 17 15:02:47 CST
UBoot Ver. : 2010.06
Kernel Ver. : 4.1.1
SW Ver. : ALPS.ICS.MP.V2.6
Custom Build Verno. : 005121017
hi, a have same phone and is it possible update new rom? Why? Because thşs rom very stable but one except, google contacts cant sync.
And i m trying cwm install with MTKdroid tools its runing but ONLY ONE TAKE. After the reboot in CWM menu coming orginal factory recovery(yellow simple screen and only have test etc. menus) why? ((
Hey.
This is my first post.
I question whether anyone would be able to help me with my phone lg d390n ? Since yesterday evening ive loaded incorrectly TWRP application for android and unfortunately since then I can not turn on your phone. Phone after you try to still vibrates and the screen is black c . Flashtool and LGMobile Support tool and KDZ and also the LG PC Suite as well as the ADB does not detect the phone even though the computer detects a device connected but you can not get to the file download mode mod I have this message :
-----------------------------
DBI Apps Watchdog Reset!
-----------------------------
DemiGod Crash Handler : DBI Apps Watchdog Reset !
Temperature Sensor was triggerd!!
CPU HOT or CPU COLD
CPU HOT or CPU COLD
CPU HOT or CPU COLD
Please do fallowing action.
1)Dload Mode. Please connect USB
2)Get the ram dump image using QPST Configuration.
--------------------------------------------------------
Board Info
rev. : 1.1, serial : 0144721a01a180d4
secure boot : disabled
------------------------------------------------
------------------------------------------------
Jump to Dload Mode.
Many thanks and repay you for any help ! ; )