AVD/HAXM RAM error - Android Q&A, Help & Troubleshooting

When i lauch a AVD in the emulator i get... "the memory needed by this avd exceeds the max specified in your HAXM configuration". When i edit/adjust the ram in the AVD to be eual or less than the HAXM config(dropping it to 768, making them eual) then relaunch the avd, the ram size remains 1024 and the same error messege is given. In haxm set up, my ram range is 512 to 949mb(default 512). I manually set haxm ram size to 768. No matter what value i assign for the AVD ram it stays 1024 when launched. Is there something i am missing as to how to save the AVD ram changes. I hope there is a answwer, I would like to have it running correctly to use with some developement tutorials. Any help would be greatly appreciated.

Related

[Q] Android System Info: Ram Threshold

Hi.
I installed the app "Android System Info".
In memory infos there is an info called "Threshold Ram".
On my tablet it is set to 128 Mb, which is very high I found out with googling.
Can you tell me how to change this value or where I find it with Terminal?
nobody?
nobody?

[Q] How much RAM size is set to be minimum to run Android?

Link: https://source.android.com/compatibility/downloads.html#android-403
According to CDD document, it is stated below
"Device implementations MUST have at least 340MB of memory available to the kernel and userspace. The 340MB MUST be in addition to any memory dedicated to hardware components such as radio, video, and so on that is not under the kernel's control."
MY Understanding is:
340 MB is required for both user and kernel space. 340 MB is for hardware components ,
So, in total minimum 680 MB
NOTE: Please correct me if my understanding is wrong ?
But, if i look at mobiles that are available in the market, they are not compliance with the requirement.
For example:
HTC ONE V , has 512 MB of RAM, but still runs android 4.0.3 , in which the requirement is 680MB.
Considering above, how the OEM vendor passes compatibility test?
keestupillo said:
Link: https://source.android.com/compatibility/downloads.html#android-403
According to CDD document, it is stated below
"Device implementations MUST have at least 340MB of memory available to the kernel and userspace. The 340MB MUST be in addition to any memory dedicated to hardware components such as radio, video, and so on that is not under the kernel's control."
MY Understanding is:
340 MB is required for both user and kernel space. 340 MB is for hardware components ,
So, in total minimum 680 MB
NOTE: Please correct me if my understanding is wrong ?
But, if i look at mobiles that are available in the market, they are not compliance with the requirement.
For example:
HTC ONE V , has 512 MB of RAM, but still runs android 4.0.3 , in which the requirement is 680MB.
Considering above, how the OEM vendor passes compatibility test?
Click to expand...
Click to collapse
i think the requirement should be 380 mb for memory and kernel(its my point of view)

[Q] swap memory created not used by phone

i have accent A400 android phone with 512 ram i have used roehsoft ram expander o create 512 swap ram and it worked and when i lanched a hd game and switched to roehsoft ram expander the swap memry was used after i rebooted my phone and created 715 ram and launched the game it exit and and it only used 1 mb ram of the available swap ram

Increasing dmesg logbuffer size over 4MB

Hello,
Anyone has any idea how to safely increase dmesg buffer size to 32MB on Nexus 9? I use Android 5.0.1.
I set CONFIG_LOG_BUF_SHIFT=22 in flounder_defconfig at compile time in order to increase buffer to 4MB (also edit Kconfig to allow increasing it over 2 MB).
When i set CONFIG_LOG_BUF_SHIFT to 23 (8 MB) and beyond i will get "unhandled level 2 translation fault" exceptions logged into dmesg log or even worse device wont boot.
I assume this exception is because of CMA. It make sens as dmesg buffer memory is aligned to 4bytes so 4MBx4=16 MB. The CMA is set to 16MB increasing it to 32 MB will make device not boot.
Thank you!

Blank screen following initial grub screen

Hi
I have tried usb key, hdd install using both 32 and 64 bit, however after the grub screen my display goes blank. I have waited over 30 mins but it does load and show remix screen. Here is my config. I have this running fine on my old HP pavilion and its great so would love to be able to run it on my large Acer. Any help appreciated
OS Name Microsoft Windows 7 Ultimate N
Version 6.1.7601 Service Pack 1 Build 7601
Other OS Description Not Available
OS Manufacturer Microsoft Corporation
System Name KITCHEN
System Manufacturer Acer
System Model Aspire Z5610
System Type x64-based PC
Processor Intel(R) Core(TM)2 Quad CPU Q8200 @ 2.33GHz, 2327 Mhz, 4 Core(s), 4 Logical Processor(s)
BIOS Version/Date Phoenix P01-B2, 19/01/2010
SMBIOS Version 2.6
Windows Directory C:\Windows
System Directory C:\Windows\system32
Boot Device \Device\HarddiskVolume1
Locale United Kingdom
Hardware Abstraction Layer Version = "6.1.7601.17514"
Time Zone GMT Daylight Time
Installed Physical Memory (RAM) 4.00 GB
Total Physical Memory 3.87 GB
Available Physical Memory 1.63 GB
Total Virtual Memory 7.74 GB
Available Virtual Memory 5.45 GB
Page File Space 3.87 GB
Page File C:\pagefile.sys
Name NVIDIA GeForce G210M
PNP Device ID PCI\VEN_10DE&DEV_0A74&SUBSYS_069110DE&REV_A2\4&357F6195&0&0008
Adapter Type GeForce G210M, NVIDIA compatible
Adapter Description NVIDIA GeForce G210M
Adapter RAM 512.00 MB (536,870,912 bytes)
Installed Drivers nvd3dumx.dll,nvwgf2umx.dll,nvwgf2umx.dll,nvd3dum,nvwgf2um,nvwgf2um
Driver Version 8.17.11.9666
INF File oem5.inf (Section013 section)
Color Planes Not Available
Color Table Entries 4294967296
Resolution 1920 x 1080 x 60 hertz
Bits/Pixel 32
Memory Address 0xFC000000-0xFCFFFFFF
Memory Address 0xE0000000-0xEFFFFFFF
Memory Address 0xDE000000-0xDFFFFFFF
I/O Port 0x00002000-0x0000207F
IRQ Channel IRQ 16
I/O Port 0x000003B0-0x000003BB
I/O Port 0x000003C0-0x000003DF
Memory Address 0xA0000-0xBFFFF
Driver c:\windows\system32\drivers\nvlddmkm.sys (8.17.11.9666, 13.09 MB (13,728,616 bytes), 17/02/2010 06:13)

Categories

Resources