Related
So here's a peculiar incident:
I have a CDMA TP with a stock ROM and a few basic apps I gathered from these forums and others. I've had it for less than a week.
Tonite, I went to check my text messages. Suddenly, the screen went black and the phone stopped responding. After pressing the power button and fiddling with the keys, I pulled out the stylus and did a soft reset. No response. Confused by this, I tried again, but still nothing. I removed the battery, and turned the phone back on. It froze at the "Touch Pro" screen with the rom/radio/etc info at the bottom. After repeating this a few times I decided to do a hard reset. So, I turn the device on and perform the hard reset. By this point the TP is only turning on SOME TIMES, and I have to take the battery out and put it back in often just to get it to start successfully. So, I finally get the device to boot up and it starts to configure WinMo. Suddenly, while configuring, it freezes. Now I try to turn it back on, and nothing happens.
Basically the device is stuck like this, shifting between not turning on at all and turning on but freezing at the "Touch Pro" screen.
So, my question is, what the heck is going on here? Has anyone else had this problem, or does this sound familiar to anyone? Any help would be greatly, greatly appreciated.
p.s. Yes, the battery is fully charged.
kameisama said:
So here's a peculiar incident:
I have a CDMA TP with a stock ROM and a few basic apps I gathered from these forums and others. I've had it for less than a week.
Tonite, I went to check my text messages. Suddenly, the screen went black and the phone stopped responding. After pressing the power button and fiddling with the keys, I pulled out the stylus and did a soft reset. No response. Confused by this, I tried again, but still nothing. I removed the battery, and turned the phone back on. It froze at the "Touch Pro" screen with the rom/radio/etc info at the bottom. After repeating this a few times I decided to do a hard reset. So, I turn the device on and perform the hard reset. By this point the TP is only turning on SOME TIMES, and I have to take the battery out and put it back in often just to get it to start successfully. So, I finally get the device to boot up and it starts to configure WinMo. Suddenly, while configuring, it freezes. Now I try to turn it back on, and nothing happens.
Basically the device is stuck like this, shifting between not turning on at all and turning on but freezing at the "Touch Pro" screen.
So, my question is, what the heck is going on here? Has anyone else had this problem, or does this sound familiar to anyone? Any help would be greatly, greatly appreciated.
p.s. Yes, the battery is fully charged.
Click to expand...
Click to collapse
Time to take it in and get a new one.....
Same problem here phone started b not coming out of lock mode. Backlight is on but no display on screen (if i tilt the screen left and right i can see light coming from behind) did about 6 hard resets and still same problem. also power button works whenever it wants to. this phone sucks @ss, i want my mogul back. on a second note my replacement will be here on wednesday.
Touch Pro stock rom purchased back in nov when it came out
yeah, i've had the same problem, i found if i hit my phone on the back or side and then batter pull and hit the soft reset while off, not the power button to turn it back on, it comes back on with color on the screen not just blank black screen with backlight, this works mostly every time, but when it doesn't, i just hold the power button down and do battery pull and hit the power button and it works, its like its got a combo of things you have to do before it works.. weird
Boot Up
I have also had similar problems. I for some reason sometimes have to remove my SD card and boot up without it for some reason. Not all the time, but every once in a blue moon. Not too sure how that affects anything, but you may try that too.
well i started a thread here ***help*** because i kinda have the same problem.
i downloaded some cabs, nothing fancy but i had some problems with a theme i downloaded. when i went to deleted i couldnt..... to make a story short, i took it to the sprint store where they tried to do a master reset/ hard reset and it wont take it. it wont do a thing... they say some important files are missing...
the phone works but not the way it should... the time on the home screen wont show up. and some other small things...
dont know how this happened but i would like to know... im worried about new programs to the phone now. ( getting a new one)
still want to see if i can fix this one.
Mayonesa said:
well i started a thread here ***help*** because i kinda have the same problem.
i downloaded some cabs, nothing fancy but i had some problems with a theme i downloaded. when i went to deleted i couldnt..... to make a story short, i took it to the sprint store where they tried to do a master reset/ hard reset and it wont take it. it wont do a thing... they say some important files are missing...
the phone works but not the way it should... the time on the home screen wont show up. and some other small things...
dont know how this happened but i would like to know... im worried about new programs to the phone now. ( getting a new one)
still want to see if i can fix this one.
Click to expand...
Click to collapse
Have you tried re flashing the ROM?
it wasnt HTC's fault for your phone's not booting...thats what happens when u try to mess with the hardware too much and you dont know what your doing
Would you want to sell???
Reboot Brick HTC process
****DOn't take battery out after hard boot***
1.just watch videohttp://www.youtube.com/watch?v=sk56olMkCtU and do what they do but dont take battery out. LEAVE phone STUCK on BOOT screen. Nothign else will move or work but you want phone just like that.
2. connect usb cable to active sync. (this may not link up but leave usb connected anyhow) Do not delete phone profile.
3.use rom like Download MightyROM6_Herman.exe avail at: http://www.lilrico.com/Mighty/mightyromblog/?p=454
4 although active sync is still attatched but may not be connecting. It will connect thru usb anyway when you run the rom software. http://www.youtube.com/watch?v=fV2I2WAFkg4&NR=1
This worked and kept phone from cutting on and off. and restored ROM. don't know about original htc boot. but your phone will work under this rom for now and you can go from there.
hey thanks plain ole dumb, it works now.
man I thought it was over.
thanks again
Sunday, I started having a problem where my phone (AT&T Galaxy Note 2) would bring itself out of the lock screen without me touching anything. The screen will stay on for 10-15 seconds and then shut off again. It will then stay off anywhere from a few seconds to a few minutes.
Very odd, right? I figured I downloaded a bad app that was causing the issue. I removed practically every app I could (I wasn't going to go through all of them to see which had permissions to bring the phone out of standby). It still kept doing the same thing.
So I did a hard reset on the phone. That should clear everything, right? The problem still kept happening.
I start thinking maybe it's a hardware issue... EXCEPT for it doesn't happen when the phone is in Airplane Mode! Which brings me back around to thinking it's some rogue app, but it still happens even when there's nothing but the default software installed from after a hard reset. It can't be the power button or a bad proximity sensor if it doesn't happen in Airplane Mode, right?
So I took it to the AT&T store and I didn't expect much. The one guy tried to play with my settings and didn't find anything wrong. He took it to the manager in the back room and the manager said I should do a hard reset (ignoring the fact that I told his employee I already had done so twice).
I've looked for answers online. The ones I've found I've tried. I've removed all applications. I've changed the screen time outs. I've even downloaded a Lock Screen replacement program. I've tried using anti-virus to scan for problems. It starts to happen again immediately after I perform the hard reset. I've moved the brightness settings. I've removed the S-Pen thinking it might be causing issues. I've turned on and off motion options. I've turned on and off wi-fi, GPS, screen rotation, multi-window, etc. Power Saving mode doesn't help. Blocking Mode doesn't help. The only thing that works is Airplane Mode.
I have NOT tried rooting my phone. I'm scared to do so, even though I'm a UNIX admin and a techie and shouldn't be scared of something like this.
Has anyone ever experienced this? I'm running whatever the normal, latest AT&T android version (4.1.2) for the Note 2. This is killing my battery and reducing screen life (is that a big deal though? I don't know).
This seems an overly obvious question. Does the watch have vibrate? I just got it two days ago, but no setting of vibrate anywhere seems to make it shake. I would think I'd have run across someone else saying something if it lacked the ability...
So, kinda wondering if mine is broken or if I totally missed that it isn't there.
Thanks
jd
jdommer said:
This seems an overly obvious question. Does the watch have vibrate? I just got it two days ago, but no setting of vibrate anywhere seems to make it shake. I would think I'd have run across someone else saying something if it lacked the ability...
So, kinda wondering if mine is broken or if I totally missed that it isn't there.
Thanks
jd
Click to expand...
Click to collapse
Mine vibrated yesterday and now it wont vibrate. If you scroll down from the top on your home screen, click the icon in the top right corner, that should bring up your wifi, airplane mode, gps, battery, etc icons. If you scroll down to audio profiles, there is one called meeting that has a picture of a phone vibrating. That should make calls and messages vibrate your phone. You can also manually turn them on because if you go to settings/device/audio profile/settings for general where you can select vibrate plus ring, and if you scroll down there is an option for vibrate on touch. Even though I have both these settings checked, and they used to work, they are no longer working. I tried a factory reset, and that didn't fix it. Now, when I power on my watch, I get a message that says headphones disconnected. It seemed to stop working after I started getting this message, not sure if that is normal or if it has anything to do with it. I will let you know if I figure out a way to get mine vibrating again, but for now it looks like mine could be broken. Can anyone else chime in on this if this has happened to you?
flimmyflam said:
Mine vibrated yesterday and now it wont vibrate. If you scroll down from the top on your home screen, click the icon in the top right corner, that should bring up your wifi, airplane mode, gps, battery, etc icons. If you scroll down to audio profiles, there is one called meeting that has a picture of a phone vibrating. That should make calls and messages vibrate your phone. You can also manually turn them on because if you go to settings/device/audio profile/settings for general where you can select vibrate plus ring, and if you scroll down there is an option for vibrate on touch. Even though I have both these settings checked, and they used to work, they are no longer working. I tried a factory reset, and that didn't fix it. Now, when I power on my watch, I get a message that says headphones disconnected. It seemed to stop working after I started getting this message, not sure if that is normal or if it has anything to do with it. I will let you know if I figure out a way to get mine vibrating again, but for now it looks like mine could be broken. Can anyone else chime in on this if this has happened to you?
Click to expand...
Click to collapse
I cannot get my vibrate to work again, if anyone has experienced this, please reply and let me know how to fix it, for now, i am giving up, and extremely disappointed
jdommer said:
This seems an overly obvious question. Does the watch have vibrate? I just got it two days ago, but no setting of vibrate anywhere seems to make it shake. I would think I'd have run across someone else saying something if it lacked the ability...
So, kinda wondering if mine is broken or if I totally missed that it isn't there.
Thanks
jd
Click to expand...
Click to collapse
It does vibrate. But very few things use that function it seems. I was thinking about setting up a tasker script to vibrate on any notification.
mortis2600 said:
It does vibrate. But very few things use that function it seems. I was thinking about setting up a tasker script to vibrate on any notification.
Click to expand...
Click to collapse
Anyone have any ideas on how to get mine vibrating again? I've done the backup and restore option, is that how you do a proper factory reset, or is there another way I can try to get this thing to start working again?
update: Just flashed 1900_20140120 firmware using the excellent guide on here, and still no vibrate
flimmyflam said:
Anyone have any ideas on how to get mine vibrating again? I've done the backup and restore option, is that how you do a proper factory reset, or is there another way I can try to get this thing to start working again?
update: Just flashed 1900_20140120 firmware using the excellent guide on here, and still no vibrate
Click to expand...
Click to collapse
Mine started working. Not sure why; I tried to reset to factory and despite following the directions and watching Loki's video, i managed to lock the watch up. Popped the battery, put it back together, wiped the device. Now it vibrates and that is good. Just wish i knew what I had did that fixed it.
Thanks all!
Jd
Mine does not vibrate either, never did.
I tried with the stock firmware, Loki's firmware, stock with enhanced security... no luck...
Thoughts?
jdommer said:
Mine started working. Not sure why; I tried to reset to factory and despite following the directions and watching Loki's video, i managed to lock the watch up. Popped the battery, put it back together, wiped the device. Now it vibrates and that is good. Just wish i knew what I had did that fixed it.
Thanks all!
Jd
Click to expand...
Click to collapse
stanelie said:
Mine does not vibrate either, never did.
I tried with the stock firmware, Loki's firmware, stock with enhanced security... no luck...
Thoughts?
Click to expand...
Click to collapse
Mine started vibrating again. I went to take the battery out, but couldn't get the screws off, so I gave up, when I rebooted, all the sudden vibrate worked again. Not sure if it was powering it on and off a few times, or shaking it around, try taking the battery out and putting it back in if you can, if not, just try turning it off and then on and maybe lightly shaking it around
Well,
It looks like a bad electrical contact, I've downloaded an app called "vibrater" that does just what it says, and it won't start the vibrator until I lightly tap the watch on it's side while the app is turning the vibrator on.
But it does not stick. I guess I will have to return the watch to have it fixed...
Until tonight, I thought the TrueSmart just didn't have a vibrator...
Vibration doesnt work
Hey, just received my Omate Trusmart! (Kickstarter edition)
Overall I am extremely happy with the watch, but there are a couple of major problems:
1. The vibration doesn't work, I have tried rebooting, factory restore etc but nothing seems to work. Does anyone know a fix to this or is it a hardware problem?
2. My screen has very faint dark spots in the center. Looks like a manufacturing defect.
Is it possible to return the watch to get a replacement? I havent opened the back cover yet.
Thanks.
after exchanging my phone due to the reboot problem, im encountering a new problem
my screen sometimes turns on by itself, and if i try to operate it at that point, the screen will turn black and nothing is functional except for the soft buttons and the pull down menu, only restart will solve this
sometimes it will also just crash to black even without the screen turning on by itself scenario
does anyone have the same issue? i suspect this is a software problem
I just got the z5 last night, and experienced the same problem this morning. Turns out that if you give the power button a 'double click', the screen comes back on. So this solves the problem reported above.
HOWEVER, there must be a setting (I hope) which we can change, I find it very irritating that as soon as I make a call, the screen goes blank, and you have to double-click the power button to see what is happening. If anyone knows about such a setting, please let us know!
My screen went black about an hour ago.
After Hotspotting for 40ish minutes so I could use my iPhone on the way to work on the train, I tried to check this forum with my Z5C, the back of it was really hot & after a few minutes, the screen went black & the phone was unresponsive for around 20 seconds & then basically unusable once it came back on, for another 20ish seconds, due to lag.
meganeet said:
after exchanging my phone due to the reboot problem, im encountering a new problem
my screen sometimes turns on by itself, and if i try to operate it at that point, the screen will turn black and nothing is functional except for the soft buttons and the pull down menu, only restart will solve this
sometimes it will also just crash to black even without the screen turning on by itself scenario
does anyone have the same issue? i suspect this is a software problem
Click to expand...
Click to collapse
Did you ever find a resolution for this? it is driving me crazy, I've tried factory resets, software repairs via the Sony Companion and this still occurs, sometimes it won't happen for a week then sometimes it happens multiple times in a row even straight after a reboot. The fix that RohitMayor describes does not work on my device. This phone is really terrible compared to the Z3 Compact
I have the same issue. This pb occurs since i have update my phone to 6.0.1...
Any solution ?
I've noticed over the past 2 weeks or so that all of a sudden the phone sometimes doesn't bother with the lock screen. I'll double tap to wake and it'll go right to the home screen (or to whatever app I was in last). This happens with or without notifications. I thought it was something caused by Evolve because it seemed to stop once I cleared data/froze it with Titanium but it's started back up again.
Running Android M, rooted, with Xposed. However, I have not installed any new modules or done any system updates during this time. All of the phone settings look correct, and are unchanged, and there isn't a setting for 'skip the lockscreen like 30% of the time' anyway.
Anyone have any ideas? Could it be an app causing this? I believe those are the only things that have been updated.
Something like Greenify?
Any ideas on where to start troubleshooting would help. Thanks.
Still fighting with this. Anyone else? Removed everything I could find that wasn't being used. Wiped data for lockscreen settings. Wiped cache/dalvik. At a loss here. It's really annoying!
Only thing I can think of is that Power Key Instantly Locks is turned off.
jbimmer said:
Only thing I can think of is that Power Key Instantly Locks is turned off.
Click to expand...
Click to collapse
it's on, and lock timer is set to immediately.
doesn't seem to have any relation to time. sometimes I'll pick the phone up after an hour and it'll go right in without the lock screen.
negativedrew said:
it's on, and lock timer is set to immediately.
doesn't seem to have any relation to time. sometimes I'll pick the phone up after an hour and it'll go right in without the lock screen.
Click to expand...
Click to collapse
Sorry, I don't have any other ideas. Maybe someone else can be better help.
Still driving me nuts. I thought I had solved it by turning off 'battery optimizations' for anything always-on/lock screen related but that wasn't the answer. Reflashed the rom, still having the issue. Might need to reflash with a full wipe I guess.
I'd rather just move to Nougat but I can't get xposed to work properly. Life is hard haha.
in case anyone finds this thread when dealing with the same issue: Android Wear was the culprit. wakelock detector pointed me in that direction and once i uninstalled it, the problem stopped immediately and has not returned.