Hi, guys!
I'm trying to save my GT-N8000 for a while and nothing! I have USB Debugging disabled, my Recovery get stuck on TeamWin screen, and I'm able to use Download Mode, but my device is not recognized by ADB neither Fastboot.
I've tried a lot of solution the last months, but nothing worked until now. My last shot was to fill Odin3 3.10 with firmware files for PIT, BL, AP, CP and CSC. It finished the process successfully, but it didn't changed anything at all, my GT-N8000 still stuck on boot and I can't get into Recovery and the device is not recognized by ADB neiter Fastboot.
I have all drivers installed on Windows and it recognize my device each time I connect and shows that all drivers are successfully installed.
Any ideas, guys? I'm really exhausted and frustrated! Thank you all in advance!
GT-N8000 Not started, Not detected by PC... even Battery is removed.
I have a worst problem, it began after i upgraded to kitkat, but works for few months, and USB is not debugging enabled, by mistake...
until i forgets it on the power fro four hours, then i discovered that it is rebooted and rebooted and rebooted and stuck on the samsung icon, i took it for samsung to fix it they told it is motherboard, and has a price more than the device itself, so i took it from them, and tried to start it, it is failed to start after... i removed the cover and removed the battery for a minute, useless, i couldn't turn it again, i did all the things on the internet, useless.
The PC is not detecting the device.
The device is not starting on.
the battery is removed many times, and plugged again.
Even i tried to charge the battery using its poles by a direct charger on it, while it is un-plugged from the motherboard.
The device can't be start or give any power on the screen...
Kindly help... Thanks in advance.
Related
I am trying to relock my phone and install the newest RUU to get the firmware updates and I have hit a wall.
When I plug in my phone everything is peachy when its booted up and running. When I reboot into fastboot and plug in the phone it is not being recognized by my computer. I have made sure that while booted debugging is on, charge only, and everything is just as it was when I rooted(besides a different ROM). The phone isn't showing up anywhere, not in device manager and not in the devices/printers area. It will however still power the phone as it will stay on even if I pull the battery. I am running Windows 7 64. Any help would be greatly appreciated.
Also I have tried uninstalling and installing the phone drivers in device manager and restarting everything over and over, nothing is working.
Frosstyx said:
I am trying to relock my phone and install the newest RUU to get the firmware updates and I have hit a wall.
When I plug in my phone everything is peachy when its booted up and running. When I reboot into fastboot and plug in the phone it is not being recognized by my computer. I have made sure that while booted debugging is on, charge only, and everything is just as it was when I rooted(besides a different ROM). The phone isn't showing up anywhere, not in device manager and not in the devices/printers area. It will however still power the phone as it will stay on even if I pull the battery. I am running Windows 7 64. Any help would be greatly appreciated.
Also I have tried uninstalling and installing the phone drivers in device manager and restarting everything over and over, nothing is working.
Click to expand...
Click to collapse
the problem might be from usb cable.
try another one if you have.
Got it, I believe it was a driver issue, but I went through several things so not sure what finally worked...
I downloaded the samsung drivers correctly because my pc recognizes any other samsung but no matter what I've tried it says usb device not recognized for my galaxy. I'm stuck in a boot loop and the only thing i can access is download mode when i plug it in the computer. I can't access anything with the battery in, it just flashes the galaxy logo over and over. Thank you for you time in advance
Did u by any chance find this phone or have you owned it from day one?
He meant "find" in the double quote
Lol
Hi guys, i realy need your help, my phone is dead.
My I9100 worked fine for two years, I flashed lots of custom firmwares by Odin. Half a moth ago, when I was going to sleep, I plugged in the charger as usually, and noticed, that it started beeping occasionally. On the display it indicated smth like: Charging... than Not Charging... than Charging and so on.
I thought that I plugged the charger incorrectly and replugged it, but it didn't helped. I was very tired and just simply turned the soud off and left the phone charging. In the morning it indicated that it is charging even when the charger was unplugged.
So I've flashed the firmware - no help, than kernel from stock to fillz - no help , than siyah than again to stock - no help. All flashings were maid via CWM. I realized that flashing will not help when I turned off the phone and it was indicating that it is charging.
I decided not to do anythig. Only USB mode didn't worked because when you want to use your phone as USB you should open the apropriate mode on the phone than there will be smth like : plug the USB data cable to enter the USB data transfer mode. I couldn't do this because my phone thought that the cable is already plugged. In forums i've got hints that my micro usb should be cleaned or small board should be replaced. So i decided to clean it. I disassembled the phone and cleaned that board with micro USB. Than turned on the phone, and connected the cable. Phone recognized it and I managed to transfer files from pc to phone. From this point I can say that all terminals on micro USB are ok.
When i unplugged the cable, phone thought that it is plugged((
The most awful part:
I decided to flash it one more time and go to stock via backup made by CWM a year ago.
But during this process the phone made a reboot by itself and after that there was no loading. I can see only name of the device and thats it.
No recovery. Only download mode.
When i connect it to PC in download mode, there is a sound that USB is connected but the device is Unknown. There is no any information about this device in dev manager on PC. I tried two USB cables, all usb ports, two laptops, all versions of USB drivers for my phone.
Earlier, drivers worked well, but now i can't understand where is the problem: Is the problem still connected with my micro usb port or i just erased boot sector and it is already brick.
I gave my phone to service center, they told that they can't help me with this. They say that usb is ok, we don't know why it is not detecting by pc.
Can the board replacement help in this issue or maybe i can do smth. in linux with my device ??? I'll appreciate any suggestions.
Yesterday I talked to representatives of service center and they told me that the problem is that internal memory is damaged and they cant flash the phone.
I took the phone and tried to flash it via Heimdall with brick fix pit.
After using this pit file, the phone was flashed normally and even turned on normally.
But in the phone info menu I saw no any data about internal memory. (It was damaged and required format). I tried format through phone menu and it did nothing.
I decided to flash the phone via Odin with normal 16 GB pit file and had a bad luck. I experienced freez during repartition. After this, phone is a complete brick.
When I connect it to PC without battery pressing vol down and rower buttons it connects as unknown device but there is nothing on the phone display. No recavery no download mode. Nothing - just reflection of my frustrated face).
Currently i'm tring to make a Jtag, maybe it'll put it in the download mode, but hope is dying....
I've herad somewhere that it is possible to put it in the download mode in linux. If somone did this, could you please give me the contact of this person?
Hi, first post here.. so Hi
I have an issue with my S3, i can't get my pc to detect it in download mode at all, no reaction from windows.. if didnt plug it in to the pc at all, it worked once, and it took me reinstalling drivers for hours to get it working, this is when i first rooted the phone using the cf-root method..
When i wanted to install a custom rom a few months ago i discovered it went back to not getting detected and has stayed that way
it's as if i've not connected it to the pc at all, i'm using a rear usb port, with the original cable, below is a short list of what i've tried
Tried 3 different cables
Used a brand new install of windows 7 with SP1
tried various Samsung ADB Drivers
Tried every single USB port, front and back on my pc
Used as many different USB Debugging options as possible
I noticed that when i turn on USB debugging after enabling developer mode, nothing changes on the pc, if i remember rightly my S2 made windows install the adb driver when i turned USB debugging on..
Any help is appreciated with this, never had any of this happen with my S2 lol :/ i've been messing around on and off the last few months with it, thankfully there's Mobile Odin and also Nandroid backups for me to fall back on
Pulling the battery with the cable plugged in while my S3 was in download mode is what fixed this for me...
With the usb cable plugged into the PC but NOT the phone, go into download mode.
Connect cable to the phone, then pull the battery out.
Once windows detects the phone and installs drivers it's safe to put the battery back in.
Phone will be detected by Odin/ CyanogenMod installer and so on.
Why in hell having the battery in stops windows detecting the phone in download mode is beyond me.. unless samsung did it on purpose? lol..
Installed CM 11 using the above method and it went perfectly, but i do have to use the above method whenever i want to flash something using my pc, so it's more of a work around than a fix..
Fix was found on YouTube of all places! hope this helps anyone else
I tried flashing CWM recovery onto my AT&T Galaxy S4 and because my phone does not connect to my computer via USB for some reason (the phone charges and my computer recognizes that there's a device in, but I cannot actually do anything with it) I flashed it with Flashify. I rebooted into recovery mode, and I got slapped with the "Unauthorized software has been detected on your phone!" message. So I tried rebooting, and I got stuck in a recovery mode bootloop with the same message. Eventually, I realized if I just go into download mode and reboot by pressing the volume down key, it doesn't try to go into recovery mode. I have already endlessly researched my USB problem, and yes, I DO have USB debugging on. ODIN recognizes that I have an external device in as well, but I haven't tried flashing anything onto my phone with it because I don't want to brick my phone because the connection to my PC is faulty. I'm using the charger that came with the device as my USB drive, so that's not faulty either. I know rooting my phone did this, and I'm pretty sure it's because I missed a step. I used this tutorial to root my phone:
[droid views dot com] /root-att-galaxy-s4-sgh-i337-android-4-4-4-kitkat-firmware-i337ucufnj4/ (I'm not allowed to post links yet, so fix the URL if you're gonna have a look)
When I flashed the I337_NC1_Stock_Kernel, my phone refused to go into download mode and I couldn't flash the I337_NJ4_Stock_Kernel as a result. I'm pretty sure that's what caused it, but I have no idea how to fix it. I'm not an expert with my phone and, despite almost soft-bricking my phone via a corrupt CWM .zip, I'm not a newbie at this either. If I could figure out how to fix this problem, I wouldn't have to worry about throwing myself into a bootloop because I can just use ODIN. I was a sitting duck before download mode rescued me, so I'd like some help as to how I can accomplish this. Any and all help is appreciated. I am 100% certain my device is the right version for that tutorial, I wouldn't try to root my phone without checking all of the simple things first.