Hi
i have formatted a Huawei Y511 using SP Flash Tool (Format Whole Flash) and and it's completely dead. Now my PC doesn't recognize my phone at all.It just add a "USB Device" into device manager when I connect it, so I'm not able to flash it using SP Flash Tool .
What do you suggest guys?
Thanks
Related
Hi guys,
I was recently trying to recover my IMEIs, I have formatted my device using SP Flash tool and when I tried to flash stock ROM after format, my PC is unable to recognize my device, I went to device manager and when I disconnected and reconnected my device to PC it is not showing any Preloader MT65xx, some "Alcatel .................." hardware is showing.
Please guide me how can make my Preloader visible in device manager. Please do not direct me to a tutorial of Installing VCOM driver, I know how to install VCOM driver, here I am unable to see my Preloader in the device manager.
dead_calm said:
Hi guys,
I was recently trying to recover my IMEIs, I have formatted my device using SP Flash tool and when I tried to flash stock ROM after format, my PC is unable to recognize my device, I went to device manager and when I disconnected and reconnected my device to PC it is not showing any Preloader MT65xx, some "Alcatel .................." hardware is showing.
Please guide me how can make my Preloader visible in device manager. Please do not direct me to a tutorial of Installing VCOM driver, I know how to install VCOM driver, here I am unable to see my Preloader in the device manager.
Click to expand...
Click to collapse
GUIDE TO RE FLASH/RECOVER/FIX IMEI (TESTED ON MICROMAX CANVAS HD A116)
If your problem is still not solved, the follow these steps:
1. Download SP flash tools, USB driver for your device, stock rom for your device.
2. Install usb drivers (no need to istall preloader etc.)
3. Run sp flash tools.
4. In scatter file, give path from stock rom (downladed as said above).
5. Remove battery, sim, and memory card all from your device.
6. On sp tools, click format and select whole flash.
7. Now keeping power button and volume buttons pressed, connect your device to pc/laptop. HOLD THE PHONE AS IS TILL SP TOOLS SAYS OK WITH GREEN CIRCLE.
8. Disconect your device after green signal on sp tool.
9. Click download on sp tools, and then follow step 7 as is. DO NOT RELEASE BUTTONS OR DISCONNECT PHONE TILL GREEN SUGNAL COMES.
10. Now install battery, sim n all. and reboot phone. Now if it stuck in boot loop. then install custom rom via recovery.
After rebooting your phone, got to engg mode and type your IMEI number and reboot andENJOY
HELP FROM WAVE RIDER
Hi All
I installed a custom ROM but it was getting stuck in boot screen ,so i did a auto format flash which deleted all the data in the phone flash including bootloader using SP flash tool v3.1312.0.139 .
As I disconnected the phone from PC it got hard-bricked. Even if i connect to PC, SP flash tool is not able to recognize the gionee p2 so I cant do any thing .
can't switch on the phone and not getting recognized in PC
Is there a way to fix it or to send the rom data to the phone flash ?
type[http]://i61.tinypic.com/jr40uh.jpg
type[http]://i58.tinypic.com/2ahedsm.jpg
Note: Before the format, the phone was working fine and was detected in PC after the flash format nothing works not even
getting detected in PC.
Regards
Arhdna
arhdna said:
Hi All
I installed a custom ROM but it was getting stuck in boot screen ,so i did a auto format flash which deleted all the data in the phone flash including bootloader using SP flash tool v3.1312.0.139 .
As I disconnected the phone from PC it got hard-bricked. Even if i connect to PC, SP flash tool is not able to recognize the gionee p2 so I cant do any thing .
can't switch on the phone and not getting recognized in PC
Is there a way to fix it or to send the rom data to the phone flash ?
type[http]://i61.tinypic.com/jr40uh.jpg
type[http]://i58.tinypic.com/2ahedsm.jpg
Note: Before the format, the phone was working fine and was detected in PC after the flash format nothing works not even
getting detected in PC.
Regards
Arhdna
Click to expand...
Click to collapse
of course it'll go dead. you just removed the OS without replacing with anything. you'll either need to get the stock backup or backup a working phone using MTK droid tools then re-flash the stock backup
My phone was bricked.When I tried to install 4.1.2 version.It didn't load to me.Then I disconnected it from my Computer and it stuck on screen that show 'you need to connect your phone to computer' how to fix this?Please help me GT-i5500.
Fix your Bricked phone
first of all download your stock rom and sp flash tool. unzip your stock rom.
then open sp flash tool and load "scatter loader for mt65xx.txt".
Then connect your phone with usb cable without battery and click on "Download" in the sp flash tool.
that's it. wait a while it will show u a green ring when it is done.
FLASHED 2.DUMP_ROM [SPFT][ROOTED] FROM All About CherryMobile Flare 4 AFTER IT SAYS FLASHING IS DONE 100% WITH CHECK MARK THEN MY PHONE DIDNT RESTART I WAITED FOR ABOUT 15 MINUTES TO SEE IF THERE'S SOMETHING MIGHT HAPPEN BUT NOTHING ONLY BLACK..
SO I PULLED THE USB CONNECTOR, THEN PLUG IT BACK. THE ONLY THING THAT I SAW IS UNRECOGNIZED USB. NO CHARGING LOGO OR ANDROID OR ANYTHING EVEN THE LED INDICATION OF CHARGING IS NOT BLINKING.
I HOPE SOMEONE CAN HELP ME :crying::crying::crying::crying::crying::crying::crying:
UP
I also had the same problem and I also cried. Your phone have MediaTek MT6753 Chipset. I have MT6582. You flashed ROM via recovery and looks like ROM have conflict with bootloader.
SP Flash Tool can flash shutdown MTK devices via USB. Your computer show "UNRECOGNIZED USB". SP Flash Tool need special ROM and driver to find your phone. Not sure, that SP Flash Tool can help you, but it helped me.
How I decided problem:
I waited some time (I went sleep, it was night)
Found stock ROM for Flashtool. This ROM contain all data for device and have more size.
Install driver for my phone.
Pulled out battery.
Connect with computer via USB.
Put in battery and computer detected phone as "MediatekDevice". SP Flash tool also detected phone
Started flashing.
Good luck!
AlexanderBabansky said:
I also had the same problem and I also cried. Your phone have MediaTek MT6753 Chipset. I have MT6582. You flashed ROM via recovery and looks like ROM have conflict with bootloader.
SP Flash Tool can flash shutdown MTK devices via USB. Your computer show "UNRECOGNIZED USB". SP Flash Tool need special ROM and driver to find your phone. Not sure, that SP Flash Tool can help you, but it helped me.
How I decided problem:
I waited some time (I went sleep, it was night)
Found stock ROM for Flashtool. This ROM contain all data for device and have more size.
Install driver for my phone.
Pulled out battery.
Connect with computer via USB.
Put in battery and computer detected phone as "MediatekDevice". SP Flash tool also detected phone
Started flashing.
Good luck!
Click to expand...
Click to collapse
thanks bro.
now it show dram fail (4032)
Plz help me....i tried to flash a ubislate 7c+x with sp tool and drivers were successfully intsalled first i used download only then it showed( pmt change) then i formated it from sp tool format option..then my tab doesn't turn on and then it shows enable dram..so i downloaded another firmware then again i flashed with sp tool this time it successfully flashed but my tab doesnt power on..i tried to flash without battery also but it doesn't worked..then i take a memory test it showed nand not detected.. and its doesnt power on....help me