I assume my NAND rw is corrupted and would like to confirm that and get recommendations what to flash now.
Here's what happened:
Been running Resurrection Lollipop for a while successfully until Play Services started force closing loads. Upgraded to CM13 hoping it would resolve it, it didn't. Ended up with Cyanogen Recovery that came with CM13, which didn't allow me to flash any other rom ('installation failed'). Tried flashing CWM Touch Recovery 5.8x with Odin, which got stuck at Open NAND, had to close Odin eventually and the phone is now giving the Samsung recovery error (Firmware error encountered...). Kies won't recognize it despite driver reinstall, Kies' recovery function doesn't list it. When trying to flash the CWM Recovery i'm getting a NAND write error. I found an old thread on this issue on GB/ICS, but not sure if their steps apply to LP/MM, let alone which files to use now.
Thank you all in advance for being helpful!
@tiethilo
Flash stock 4.1.2 with Odin. If odin flash will be succesfull , phone should end in Samsung animation bootloop. If it haleens , take out battery , go to recovery , select wipe data/factory reset and viola. Your phone should be working.
Related
Hi Everyone! just a rookie here in need of a bit of advice.
I'm a Galaxy S II I9100 owner and have my phone rooted and all setup with custom roms and been comfortable with flashing for some time now. My ROM of choice recently was Vanilla Rootbox and have to say the ROM has been fantastic with very few bugs to report. Last night i recieved the OTA update via Goo Manager for Vanilla Rootbox 3.4. I downloaded the full update over wifi and flashed with all wipes no worries. Next step was to flash the latest GAPPS and i figured there would be nothing wrong with flashing the GAPPS zip i had on my sd card that i had downloaded the last time i was notified of a GAPPS update via Goo manager as well. After flashing, wiping everything and rebooting again. My phone then booted up to a series of dialog boxes indicating that many google processes had stopped functioning. apps.google.com etc etc. A similar error has been reported in the Vanilla Rootbox thread by another user but i wasnt able to report this bug their either because my post count is too low to post in a development forum. So after seeing this error i rebooted into recovery to flash my last backup but CWM recovery came back with an error messaging stating it couldnt mount either ext or int sdcard. i did a factory reset which made no difference to the problem whatsoever. I then downloaded ODIN and the latest stock ICS Rom and flashed it via ODIN with no reported errors. My phone now boots through the optus boot animation and is stuck at the Galaxy S 2 screen with the flashing red and yellow animation over the S. If i turn off the phone with the power button, the phone turns off and immediately starts again and gets stuck at the flashing s screen. I've taken the battery sim and ext sd card out and put it all back in only for the problem to persist.
If anyone could help me there's a donation and my thanks in it!
Much appreciated
Nick
tried to re flash another stock ROM?
If so, tried factory reset the phone after the flash?
As long as you can get to DL mode, you are good to keep on flashing till you are up & running.
And then you got this
Remember to update your kies and make sure you close it all up before flashing with odin. If you are in 4.0.4 beware of the brick bug.
gastonw said:
tried to re flash another stock ROM?
If so, tried factory reset the phone after the flash?
As long as you can get to DL mode, you are good to keep on flashing till you are up & running.
And then you got this
Remember to update your kies and make sure you close it all up before flashing with odin. If you are in 4.0.4 beware of the brick bug.
Click to expand...
Click to collapse
Kies has never been installed on this computer but i did use the usb drivers mentioned in the soft brick recovery guide you linked. I used some information from the guide to flash this stock rom but i couldnt flash or wipe the partition because im unsure where to get the .PIT file required? i cant get past the boot animation so no factory reset possible and yes i can still get into download mode!
darkstar117 said:
Kies has never been installed on this computer but i did use the usb drivers mentioned in the soft brick recovery guide you linked. I used some information from the guide to flash this stock rom but i couldnt flash or wipe the partition because im unsure where to get the .PIT file required? i cant get past the boot animation so no factory reset possible and yes i can still get into download mode!
Click to expand...
Click to collapse
wow wow, leave pit files alone for now, they are nasty.
What stock ROM did you flash? 4.0.4 or 4.0.3?
You can factory reset via recovery mode.
Try installing kies anyway, it can't never hurt. Just make sure all applications are closed before you re-flash.
here's jb leak, might help:
http://www.sammobile.com/2012/11/15/i9100xxlsj-%E2%80%93-galaxy-s-ii-android-4-1-2-jelly-bean-test-firmware/
Right so i flashed I9100XWLP8 stock rom (4.0.3). Just then i flashed Siyah Kernel and attempted to use the factory reset function in recovery there, i get a message down the bottom mentioning that it can't mount my internal SD.
darkstar117 said:
Right so i flashed I9100XWLP8 stock rom (4.0.3). Just then i flashed Siyah Kernel and attempted to use the factory reset function in recovery there, i get a message down the bottom mentioning that it can't mount my internal SD.
Click to expand...
Click to collapse
Tell me your:
Model
Firmware
Country
Carrier
Always mention this
try flashing jb leak (ROM, modem & kernel package).
While I did find a similar posts, they were for different devices. I also tryed to search o different sites for similar problems to no avial.
What Happened: After backing up system data and app data then removing Foxhound ROM with factory reset, and installing UltimaROM i came to find that the modem did not install correctly result in no connection to my cell network. I booted into TWRP recovery to try and do a re-install of the ROM only to find that TWRP was restarting itself every 3 seconds or so. I attempted to restart the device which i found to result in a TWRP bootloop that i cannot get out of, it constantly is booting into recovery mode and i cannot get it restart the OS.
What I've tried: Since i can get into download mode i decided to attempt to re-install TWRP using Samsung Galaxy S3 Toolkit but since i do not have USB debugging on i cannot do that. I'm mainly looking for a fix before i go and claim it on the warranty saying update went bad or something. If people need more information I will try to provide it as best i can.
Summery if i confused people is that TWRP is in a bootloop, i am unable to get to the OS, but i still have download mode available.
I fixed it but not how I would have liked to. I ended up losing all data due to flashing stock ROM using ODIN. I would still much appreciate a alternative method that does not involve loss of data though just for future reference, that is if anyone knows a alternative method.
Sent from my GT-I9300 using xda app-developers app
could've tried reflashing TWRP or any other recovery through odin
I have an LG Optimus Q (LGL55c) with twrp loop. I was trying to go back to stock rom, instead I deleted all the system files in twrp when it was working...Then I rebooted back into recovery and get the loop. Does this mean I completely bricked my phone? I tried using adb, adb shell doesn't work. It does find the device. Even tried the LG update with no sucess Any ideas or suggestions?
I just read the forum title, I thought this was for the Optimus Q not the Samsung S3. Sorry mods
Temasek unofficial cm12 5.02
I was running this rom when my power button shorted and I got it replaced but then I tried to do a complete wipe and clean flash but since then it has been twrp bootlooping, tried to flash the latest recovery through Odin but still doesn't work also tried stock firmware flash but says binary not available.
This is my secondary device and I've not been in touch with Odin for a while. Any help will be appreciated.
Thanks
Download latest firnware from sammobile.com and flash it with Odin, as described on sammobile: does Odin finish with '1 succeeded'?
I'm in a very similar situation, but with my Samsung Galaxy Note 2 (N7105). It's rooted, and I am, or was using TWRP 2.7.0.2. ROM is CyanogenMod 12, 5.0.2 Lollipop.
I did a factory reset from INSIDE Android, and chose to wipe internal memory. Phone did the reset and wipe, rebooted into TWRP instead of Android, and now I have TWRP boot loop.
I posted more about it here: http://forum.xda-developers.com/showpost.php?p=60247503&postcount=3671
I have the Problem toooo!
What must i do Now!
with my S3 is the same!!!
For posterity:
With an old (2014?) version of TWRP and a custom ROM, I tried reverting to factory settings. That caused the phone to reboot TWRP, and the screen would flash every couple of seconds. I flashed a stock recovery image I found on Google, and when it restarted again, the wipe was completed successfully. My intention was to wipe all user data anyways so I can't say if this method might save it.
Hello.
I have a GT-i9305 andI tried the rooting by following the instructions at http://galaxys3root.com/ on my Ubuntu laptop with heimdall.
I managed to install the recovery and also flash the cwm zip. I saw som problems related to /cache/ so I wiped cache and after that I have not been able to get past boot logo. I hav ealso tried flashing a custom rom and doing a factory reset and wipe dalvik cache bu
t it did not help. I have tried Odin and flashing from a .tar.md5 file but it results in FAIL.
I can reach both download mode and recovery but that is all.
Please help, I need my phone.
did you use a i9300 method on your i9305? you've probably killed the phone.
flash a stock ROM via Odin (i9305 one) and factory reset from recovery. if that doesn't help - send it to Samsung.
And this is the i9300 section, you're in the wrong place
Thanks.
I got back to stock. I will try to use the i9305 method.
Mount /sdcard not possible
Wel, I have the same problem.
Samsung SIII International version. After installing a new rom (believe it was "jellybam-v6.1.0_i9300-STABLE.zip") but I am not sure, the phone boots only to the original logo and then the screen goes black. Nothing more.
I can get into recovery mode and download mode so I tried several recovery versions (CWM, TEAMWIN, latest ClockworModRecovery v 6.0.2.8.) and several ROM.
No mater what I install, I get the same results. Boot phone and it hangs after the standard Samsung logo.
I was able to find out "/sdcard" could not be mounted. All the recovery programs I used with the option "mount unmount" reporting the same "/sdcard could not be mount" error.
Formatting /sdcard all so won't work.
I am thinking installing a new kernel but I have some difficulties in finding witch one will work with my phone?
Any suggestions or help is really appreciated b/c I have no idea what to do next.
Samsung I9300
Win 7
Latest USB drivers from Samsung installed
No Kies installed.
Odin3_v3.07 installed.
Using Odin I flashed:
CF-Root-SGS3-v6.4.tar
recovery-cwmtouch-6.0.2.8-GTI9300.tar
recovery-stock-dlj4-GTI9300.tar
recovery-stock-blg9-GTI9300.tar
And a few more.
Due to being unable to acces the phone installing a zip file is not possible. Using "installing a rom from zip, or sdcard" from recovery is not possible.
I tried installing a file using sideload but was not succesfull. I can get the phone in receiving a file from sideload but was unable to send a file from the PC.
Thanx in advance
you have to do a factory reset after flashing a new rom
Did wipe/clear/factory set etc every time just to find the phone goes black after the Samsung logo.
One particular thing: I can see the /sdcard in some recovery programs but can't modify it.
How can I transfer a zip file using Sideload?
I can get into "download a file using Sideload" on my phone but what should I do to get a zip file transferred. Maybe then I can use "install from zip" from a recovery.
Update Problem solved (for me) http://forum.xda-developers.com/showthread.php?t=2162908
I flashed the 9305 firmware from here http://www.samfirmware.com/ in Odin then I was back to stock.
Then I rooted the phone by this instruction.
http://www.ibtimes.co.uk/articles/4...-lte-android411-android412-jellybean-root.htm
I have not tried a custom rom but I think it should work.
Hi folks, mid last week I woke up to a non responsive Galaxy S2. It's been happily running stock Vodafone ICS for over a year, and somehow spontaneously went soft brick on me. Gets stuck at logo screen or goes into boot loop.
Download mode is accessible. I can flash through Odin (1.85 and 3.09) and it reports success. I have successfully put CWM (various versions) on it can can boot into them fine.
Recovery mode is also accessible and appears to be working fine. I can access external SD card no problem.
Attempting to flash through zip from external SD aborts with Mode 7, reporting bad zip or unable to read source file. I have tried removing asserts from install script (educated myself to the risks and made sure the ROM was correct!!) and multiple versions of CM (10.1.3 stable, 10.2 nightly) and multiple versions of CWM recovery (6.0.2.9 is what I've been using mostly, as recommended by CM guide)
Tried running GS2ROMNukeV2.12.zip which reported successful wipe, then attempted zip install from SD with same result (aborted mode 7). Repeated wipe and attempted stock (I9100TDVLSK_I9100THUTLSD_I9100TDVLS3_HOME.tar) from flash through Odin. Reported success, phone booted into recover and applied KOR CSC successfully, then reboot and still stuck at logo screen/boot loop.
I have attempted the fix in http://forum.xda-developers.com/showthread.php?t=1449771 as best I could wish the resources I could find, but it's hard to follow to the letter with the links broken!!!
I have not tried repartition with PIT as I'm not sure where to get an appropriate PIT file. Advice on this appreciated!
I want to make this clear because people seem to not want to believe it: I did not soft brick my phone flashing it. My best theory at this point is some kind of memory corruption or hardware failure that's causing a boot loop. Any help or suggestions would be appreciated. This week I will probably take it in to a repair shop and hope for the best, but tomorrow is a public holiday and I've got nothing to lose by trying any more suggestions.
Kaine said:
Mode 7
Click to expand...
Click to collapse
If memory serves me right this is due to an old version of Recovery, i had the same thing, updated recovery and it flashed zip fine. just as you know. :fingers-crossed:
Hey guys! I had recently installed an Android 4.5 rom on my Samsung Galaxy S i9000, but I didn't really like it, so I went back to clockwork mode and restored the backup (which I am pretty sure I had saved prior to installing the rom). What happened then was that I couldn't power on my device. It literally gets stuck on the Samsung Galaxy I9000 startup screen. I can however access download mode and I can access clockword mode recovery. BUT, when I try to install another update with clockword mode recovery or trying anything on cwmr for that matter (factory reset, cache reset, anything...), I get the error message: Unknown path to /sdcard and I am stuck at this. Can anyone tell me how to fix this issue? Please, I need help quickly!
I would just restore with official firmware via Odin and restart the process. This will set everything back right so you can have a fresh start. http://forum.xda-developers.com/showthread.php?t=1102881