Related
Hi, is there any chance to get Topaz disassembly guide?
THX
Edit: Dont need it anymore, I have done it, not difficult at all (similar to Nokia phones). HTC made Topaz very easy to disassembly.
I was cleaning part between digitizer and LCD from dust with antistaic brush and compressed air.
There are just 3 connectors to disconnect mainboard (digitizer, phone receiver and LCD), to get to the LCD. No coaxial cables to connect GPS and bluetooth antenna (all just by touch connectors to the black plastic top back part), Chipset is covered by metal plate, cant see it.
LCD: S/N: 1EJV093Q000069
P/N: 60H00209-00M S508
Can I request you get some high res photos of the PCB/LCD and/or record the ic part numbers while you've got it apart? It would be really useful to know for Linux/Android development.
Can you post what kind of gps chipset is buildin ?
Thanks in advance
Daniel
Thanks for the photos! Would you be able to post a higher res version of the 3rd one or simply scribe what is written on the back of the LCD. I'm hoping the serial number might give an indication of the chipset used in the LCD.
cheers!tsy
So you can sure tell us if the front frame is really metal or plastic ?
Its metal body iside of plastic housing.
Great job !
Thanx
some instructions or tips of how you disassembled it would be nice
i unscrewed my diamond2, and i cannot find a way to disassemble it..
help!
Hi
Nice work and photos.
One problem that has been reported, and I assume it was something you suffered from, is dust entering through the volume rocker and finding it's way onto the LCD display.
This seems rather an oversight by HTC as usually the LCD panel would have some form of seal or bezel (sticky or foam) to stop dust. Does the LCD panel have anything like this at all?
Regards
Phil
i found a htc service manual for diamond 2 that was leaked
not sure if i can post it here..
it explains how to disassemble the device
EDIT: I am so sorry, the leaked document is the user manual, it is incorrectly posted as the service manual in many sites. sorry
post it! what's the worst they can do... tell you to remove it?
PhilipL said:
Hi
Nice work and photos.
One problem that has been reported, and I assume it was something you suffered from, is dust entering through the volume rocker and finding it's way onto the LCD display.
This seems rather an oversight by HTC as usually the LCD panel would have some form of seal or bezel (sticky or foam) to stop dust. Does the LCD panel have anything like this at all?
Regards
Phil
Click to expand...
Click to collapse
Look here:
http://forum.xda-developers.com/showthread.php?t=520795&highlight=solution%21%21%21
Sticky? New Thread? & Help
I think we either need to sticky this, or make a new thread that encompasses all disassembly / dust leak information about the topaz.
I still cannot disassemble my device, i wish someone could help :/
Disassembling the Diamond 2 is really simple.
Remove the 4 T5 screws at the four corner
Remove the small plastic cover below the battery (might be optional)
Pop the main plastic body off the face piece (I use a really small flat screw driver) Starting from the top of the device
Remove the 3 connection then pop the main board
Remove the 4 hardware buttons then remove the LCD screen
I'll try to take some pictures when the new LCD screen arrives...
Guinea.Pig said:
Disassembling the Diamond 2 is really simple.
Remove the 4 T5 screws at the four corner
Remove the small plastic cover below the battery (might be optional)
Pop the main plastic body off the face piece (I use a really small flat screw driver) Starting from the top of the device
Remove the 3 connection then pop the main board
Remove the 4 hardware buttons then remove the LCD screen
I'll try to take some pictures when the new LCD screen arrives...
Click to expand...
Click to collapse
Thanks for the steps. I just yesterday disassembled my TD2, but didn't dare remove the connections on the mainboard. The one on top left (see your pic mainboard.jpg) is no issue, but the other ones are tricky...or at least I thought they are. I couldn't figure out how to exactly remove those connectors. Could you maybe give some steps or info on how to remove those connectors? Thanks again for your help.
disassembly
thanks for the update . ill try and post pictures up when possible.
I am interested in this too, I have dropped mine a couple of times and am looking to replace the housing (although I have already been ripped off once by buying a repaired one on ebay).
So any idea where I can get a legitimate full housing and a guide to moving the guts from one to another?
Cheers,
Found this:
http://www.pdacenter.ru/razborka/htc-touch-diamond2/
Now I just need to find a genuine and complete housing.
Awesome
stormyuk said:
Found this:
http://www.pdacenter.ru/razborka/htc-touch-diamond2/
Now I just need to find a genuine and complete housing.
Click to expand...
Click to collapse
Thanks for your contribution stormyuk !
You can find housings on ebay, though most don't come with the buttons.
I bought one and its practically impossible to distinguish any differences,
Buy from kr-net on ebay its the seller that sold me my housing
Before we were so rudely interrupted in the original thread, we were discussing the G1 hardware keyboard replacements. Please folks, if you must flame each other do it via PMs to avoid locking legitimate threads.
I've been able to find some inexpensive after market replacements on eBay, but still am not sure how difficult it is to actually do that. All the sites I've been able to find on the subject only provide time-lapse dis-assembly instructions of the entire phone. If anyone has done the replacement themselves, I'd greatly appreciate pointers on how to keep my phone operational after I put it back together.
I replaced the white keyboard in my Dream with a black one. It was a scary operation as it takes a bit of force to dismantle. I accidently pulled my antenna off and disconnected a flylead. ment my phone had no signal at all. later when i got home (did it in work ) i took it apart again and fixed it.
Take your time and have patience, alot of it is plastic and clipped together so requires a bit of force.
May I ask what is wrong with the keys on the bronze one? I did a quick skim of the old post and gather that you can't see the keys in daylight but I don't get why?
I'm just genuinely interested, I have a black G1 so never had such a problem.
brummiesteven said:
May I ask what is wrong with the keys on the bronze one? I did a quick skim of the old post and gather that you can't see the keys in daylight but I don't get why?
I'm just genuinely interested, I have a black G1 so never had such a problem.
Click to expand...
Click to collapse
It's the combination of silver keys with light-silver backlight that make the lettering almost impossible to see in day light conditions. I'd take a picture if I had a camera with me today. Whoever came up with that color combination should be fired. Or at least made to stare at it every day for the next year. I have to tilt the keyboard at a weird angle just to distinguish the letters. From what I understand the white G1s suffer from the same problem.
The "Backlight Off" app definitely helps as it lets you toggle the backlight with a keyboard shortcut. I'm looking for a more hardware solution though.
I've been thinking about changing keyboards and housings too. But from what ppl are saying it seems to be pretty exhaustive. Do any of you guys have the service manual? I DL'ed it from somewhere and it goes through each step of disassembly and also shows assembly. I'm sure it would help out to give an idea of what you need. But like I said, even having read the service manual, it's still quite scary.
A full housing from my understanding is a bitc(....doing the KB I can see why. The LCD portions look ridiculously complex in comparison to other phones.
That said if you have the proper tools , good organization or memory , steady hands and patience really shouldnt be "that" tough to do the keyboard.
Heres the thing. Its really not that hard to unscrew things etc...but the piece you need to move in order to get proper access to the KB has 2 ribbons that are a PAIN IN THE ASS to take off and put back properly. Theres so little room for error.If youve never worked with ribbons before BE CAREFUL.
I will say G1 is pretty unique in how its put together , I swear they were determined to make it as complicated as possible
The really pain in the ass part is that the online manual/guide will merely tell you something like "remove part A" but no explanation how. Theres also 2 screws I swear it glossed over leading to frustration when I did the trackball/front keys.
Torx 5 and really good mini screw driver are mandatory.
Nice lil workstation is really helpful..(masking tape ,towel , table lamp or LED headlamp , vitamin/pill cases etc)
Im no mechanical engineer but Ive opened up damn near everything Ive ever owned at some point. Took me a solid 3 hours from start to finish. With major time spent on organizing the screws pieces and those damn ribbons.
I will say the black KB makes a HUGE difference. Black key on the front arent necessary but do look better and add much needed contrast.
KOF33 said:
I will say the black KB makes a HUGE difference. Black key on the front arent necessary but do look better and add much needed contrast.
Click to expand...
Click to collapse
Pics, or it didn't happen
Thanks for the tips!
Chahk said:
Pics, or it didn't happen
Thanks for the tips!
Click to expand...
Click to collapse
As you can see I also replaced the trackball with a glowing white one.
lol at the trackball
doing a case swap is only bad the first time LMAO. I learned a lot, like for example the brass inserts that the screws go into...are not pre-installed. You must CUT Them out of the old housing and HAMMER them into the new oneBut in the end, it turned out very nice.
As far as just replacing the keyboard, it isnt too bad actually once you know what screws hold what down!
-Remove the 6 torx screws for the back housing
-GENTLY pry open the TOP of the casing with a plastic case tool, work your way down to the bottom of the housing. The bottom is a PITA to remove. I usually get it by rocking it gently back and forth
-remove the long and short coax leads from the motherboard side. swing them out of the way
-peel back the tape and GENTLY pull the bottom connector (mouthpiece module) from the motherboard.
-peel back more tape and lift the latch for the keyboard connector (the one on the side)
-Peel the camera module up SLOWLY (it is double side taped down) as well as the imei card. The cam cable is routed under it, lift it all as a unit. When you get to the motherboard, STOP
-Now, gently twist the whole camera and motherboard unit as a whole until it is free of the latch on the side. Gently lift the camera end exposing the 2 small ribbon connectors on the bottom.
-Peel back the tape and GENTLY lift the ribbon connectors out of the board. Place the motherboard/camera unit to the side for now.
-Remove all the black and silver screws for the metal piece. The lcd should stay in place as the mouthpiece plastics kinda hold it for you, but you should still support it to keep from hurting the connections.
-Viola, keyboard access. Remember when you put it back together be sure to re-tape all the connections, else when you drop your phone one of them may pop loose.
Keeping the motherboard and camera/imea plate all as one module saves you from a very difficult connection and will help you keep everything aligned when reassembling it.
I guess the spacebar has 2 functioning buttons, (left and right) ... well my right side just konked on me, and i was wondering if a replacement keyboard off ebay will fix this, or are they just the button "covers"?
the "buttons" are just plastic nubs that make contact on a board behind it. That board would be what you need. I dont know if there are any on eBay, but I have a spare one if you want to PM me for details.
I dropped my G1 about 6 months ago and was devastated. After entirely too much research I finally got the guts to purchase a replacement digitizer and managed to install it successfully. However, in the process I managed to rip the LCD ribbon cable. I then had to order a replacement LCD screen. I've also damaged one of the black ribbon cables pretty severely causing the touchscreen to become unresponsive sporadically. I've just placed an order for one of those ribbon cables and will hopefully have that up and running soon. I've also purchased an entire new housing unit to rebuild the phone to make it look as new.
Now when I first took this thing apart I was by NO MEANS an expert or have ever done something like this before. I'm just an avid enthusiast who wanted to save a little money, feel a sense of accomplishment and to learn a few things along the way. I technically paid nearly the same amount of money it would have cost me to send the unit to HTC for repair, however i've learned everything there is to know about my phone's hardware. I know which board does what and are extremely confident about fixing ANY hardware problem in the future.
If you have the time, patience, and truly want to become confident about the workings of your phone, then I highly recommend fixing it yourself. I've bought my parts for VERY cheap off of reputable ebay buyers. You can find EVERY single piece for your phone on Ebay. My LCD has 1 dead pixel, but I guess that's the risk you take when you buy really cheap parts.
Hope this helps.
today my at&t tilt2 accidently fell from my hands and got heavily scratched on the chrome shell (bezel) the bezel even got few small dents & & the chrome colour came out
so i wanted to ask how can i remove this bezel,as i thought to remove it sand it & then paint it chrome again
& also suggest me is my idea good or not
no rplys? atleast tell me hw can i remove those scratches & dents
i wanna know this too since i just dropped mine today and its a fairly small chip but i still get a little crazy over it
please help us out
Sorry for bad news but to remove the bezel you'll need to fully dissassemble your TP2. You'll have to dismantle the main housing to unscrew hinges. Once you separate the upper part with LCD you'll be able to open it, and then separate the bezel from LCD and digitizer. I've done it myself couple of times but be aware that is not a 5 minute job (especially if you're new to this). You'll need tools - small philips screwdriver, small star screwdriver an special plastic prying tool (couple of them, they get broken easily, you don't have to use them but you'll most likely scratch the phone). You can get tool sets on ebay. Word of advice - if only possible try not to separate LCD and digitizer. Once you get dust and/or fingerprints between them it's a HELL of a job to get rid of them.
Check out mike channon's site for dissassembly guide.
Good luck guys!
EDIT: Personally, I would rather try to do some touch-up repairs without opening the phone if possible.
touch up repairs like what? suggest me something specific
I want to replace my screen and bezel but don't mind stripping the whole phone down if thats what is needed.
Try this link http://translate.google.co.uk/translate?u=http%3A%2F%2Fwww.pdacenter.ru%2Frazborka%2Fhtc_touch_pro2%2F&sl=ru&tl=en&hl=en&ie=UTF-8
As mentioned by pjm77 this does not look easy, and chances are if your not very careful you could mess up your phone.
By touch up I mean trying to paint the damage to make it less visible. Can't really say if that's possible in your case - judge for yourself. Dissassembling the whole phone is by all means possible, I was able to do it several times and I'm just an enthusiast. Just bear in mind that unless you're really skillfull and experienced you end up with a little damage here and there (clips broken, scratches etc.), it's time consuming and there is a risk of serious damage. In the end you may just put a lot of effort into it and be a little disappointed with the final result. But maybe not, it's up to you. Whatever your decision is - good luck!
EDIT: To be more specific I'll give you the real life example of touch-up. I had an awful, long and deep scratch on the back of my LCD (you can see that black, metal part when you slide out the keyboard). I took the masking tape and precisely shaped it in a way that only the scratch was visible (I'd say less than 0,5 of mm wide). Then I took a black paint (originally for my mother's renault) and painted the scratch. Aftrer half an hour I removed the masking tape. The repair is not perfect in any way, the scratch is still there if you know where to look. But I just never noticed it again and simply forgot about it until today.
I used a touch up pen from Staples that has metallic ink. It was a Silver Pilot Pen with Fine Point tip. Like pjm said, touch up paint isn't going to make it look perfect, but the scuffs on the chrome bezel are less noticeable. The ink is a little lighter than the chrome but makes the black cuffs disappear and is nice because you can get small marks with the fine point. I think it was $2.99.
Hi all,
Ok, so i've had a small disaster. As you probably guessed already i've dropped my phone. I thought the story was quite amusing (or just plain unfortunate!) so i'll you tell that before I ask for some advice!!
I got myself a white Galaxy S2 on upgrade through Vodafone. Gorgeous piece of kit so I ordered myself a nice case and screen protector to keep it nice and tidy.
Unfortunately the case got 'lost in the post' and as such the phone was unprotected. So, with some foresight I ordered a plain white cheap one off eBay (£2 inc. postage) just to see me through the 3-5 days I needed before the case I wanted was resent.
However what was sent what not white at all - it was the most hideous case with a rather disgusting floral effect all over it. I was going out for a night in town and had no choice, I had to take it with me.
Unfortunately later that eve I was stood at the bar, and my phone went off. So to save any embarrassment I slid the phone out of it's hideous case, and proceeded to read the message. Then it happened. The slippery son of a ***** jumped out of my hand, bounced off my foot and hit the deck.
It only has a couple of dings in the chrome bezel (the chrome effect rubbed off in two places to reveal black (the plating is obviously really thin)) - everything else was ok. Phew. But i'm still gutted and annoyed with myself
So, lesson learnt. I should have left the disgusting garish floral case on and it would have saved my phone. It was only 'de-sheathed' for a second and I managed to drop it, classic.
As a temporary solution, I coloured in the affected areas of the bezel with a silver permanent marker, and used some clear nail varnish over the top to stop the pen coming off. It seems to work well actually, and it looks much better than the black marks.
So, to my question - how do I change the chrome bezel for a new one?
I have read many threads, and watched many videos, and it looks to me like a nightmare job (eg as well as taking off the back and all components, you have to prise off the screen which is glued on, disconnect digitiser, etc). Can anyone confirm this, or has anyone tried it?
I can't find any videos of changing the bezel - they all seem to only go as far as taking off the back.
I've found a couple of sellers which sell the housing in white for only £20-30, so if it's an easy-ish job i'd have a stab at it. However i'm thinking I might as well just forget it ever happened and not be so precious about keeping the phone in A1 condition - it's a phone after all and it's going to encounter some scrapes now and then, even with a case on. And I plan on keeping it for 18 months anyway.
Opinions, anyone?
Cheers!
Movisman said:
Hi all,
Ok, so i've had a small disaster. As you probably guessed already i've dropped my phone. I thought the story was quite amusing (or just plain unfortunate!) so i'll you tell that before I ask for some advice!!
I got myself a white Galaxy S2 on upgrade through Vodafone. Gorgeous piece of kit so I ordered myself a nice case and screen protector to keep it nice and tidy.
Unfortunately the case got 'lost in the post' and as such the phone was unprotected. So, with some foresight I ordered a plain white cheap one off eBay (£2 inc. postage) just to see me through the 3-5 days I needed before the case I wanted was resent.
However what was sent what not white at all - it was the most hideous case with a rather disgusting floral effect all over it. I was going out for a night in town and had no choice, I had to take it with me.
Unfortunately later that eve I was stood at the bar, and my phone went off. So to save any embarrassment I slid the phone out of it's hideous case, and proceeded to read the message. Then it happened. The slippery son of a ***** jumped out of my hand, bounced off my foot and hit the deck.
It only has a couple of dings in the chrome bezel (the chrome effect rubbed off in two places to reveal black (the plating is obviously really thin)) - everything else was ok. Phew. But i'm still gutted and annoyed with myself
So, lesson learnt. I should have left the disgusting garish floral case on and it would have saved my phone. It was only 'de-sheathed' for a second and I managed to drop it, classic.
As a temporary solution, I coloured in the affected areas of the bezel with a silver permanent marker, and used some clear nail varnish over the top to stop the pen coming off. It seems to work well actually, and it looks much better than the black marks.
So, to my question - how do I change the chrome bezel for a new one?
I have read many threads, and watched many videos, and it looks to me like a nightmare job (eg as well as taking off the back and all components, you have to prise off the screen which is glued on, disconnect digitiser, etc). Can anyone confirm this, or has anyone tried it?
I can't find any videos of changing the bezel - they all seem to only go as far as taking off the back.
I've found a couple of sellers which sell the housing in white for only £20-30, so if it's an easy-ish job i'd have a stab at it. However i'm thinking I might as well just forget it ever happened and not be so precious about keeping the phone in A1 condition - it's a phone after all and it's going to encounter some scrapes now and then, even with a case on. And I plan on keeping it for 18 months anyway.
Opinions, anyone?
Cheers!
Click to expand...
Click to collapse
Sorry to hear...similar happened to my HTC Desire...however this should help...if you buy the kit off Ebay...
http://forum.xda-developers.com/showthread.php?t=1253969
0semaj0 said:
Sorry to hear...similar happened to my HTC Desire...however this should help...if you buy the kit off Ebay...
http://forum.xda-developers.com/showthread.php?t=1253969
Click to expand...
Click to collapse
Hi,
Thanks for the information - I had a look at this tutorial yesterday, and although it's very good, it looks like this person has replaced the entire led panel/digitiser/housing in one go, rather than just the housing?
My screen is just fine, so I only need to replace the housing part.
The hardest bit looks like separating the screen from the housing from what i've read, and this is what I can't find a tutorial for, only some images on youtube suggesting to use a hairdryer to help with the proceedings!!
Thanks
Movisman said:
Hi,
Thanks for the information - I had a look at this tutorial yesterday, and although it's very good, it looks like this person has replaced the entire led panel/digitiser/housing in one go, rather than just the housing?
My screen is just fine, so I only need to replace the housing part.
The hardest bit looks like separating the screen from the housing from what i've read, and this is what I can't find a tutorial for, only some images on youtube suggesting to use a hairdryer to help with the proceedings!!
Thanks
Click to expand...
Click to collapse
Yea, the link is for the whole unit, but would give you some pointers. I am not as familar with the Samsung build, but with the HTC I know that between the LCD housing and the LCD/digitiser itself is applied through adhesive (most phones are) that is put into a temperature oven for 10 minutes to soften the adhesive. This is based on the HTC Official Service videos. I am not sure if the same will apply to Samsung phones.
But then again, as it is an expensive phone, it may be ideal for you to also get a quote from your local SSC or mobile phone repair agent to consider.
0semaj0 said:
Yea, the link is for the whole unit, but would give you some pointers. I am not as familar with the Samsung build, but with the HTC I know that between the LCD housing and the LCD/digitiser itself is applied through adhesive (most phones are) that is put into a temperature oven for 10 minutes to soften the adhesive. This is based on the HTC Official Service videos. I am not sure if the same will apply to Samsung phones.
But then again, as it is an expensive phone, it may be ideal for you to also get a quote from your local SSC or mobile phone repair agent to consider.
Click to expand...
Click to collapse
Yep, good point. I'd be interested to hear actually what the cost would be to replace the front bezel only. It's only £30 on eBay for the front and rear housing, but i'd be willing to pay more on top for an authorised repairer to carry out the job.
That tutorial is definitely one of the more detailed ones I have seen so far though. Doesn't look like many people have tackled changing the bezel only...
Thanks
Movisman said:
Yep, good point. I'd be interested to hear actually what the cost would be to replace the front bezel only. It's only £30 on eBay for the front and rear housing, but i'd be willing to pay more on top for an authorised repairer to carry out the job.
That tutorial is definitely one of the more detailed ones I have seen so far though. Doesn't look like many people have tackled changing the bezel only...
Thanks
Click to expand...
Click to collapse
Hey Movis,
What did you end up doing for your dropped phone?
I too have dropped my phone on its corner and the chrome along with the plastic is now dented.
Another one with the same problem here. I managed to create a bump on the chrome bezel.
Can I bump this post as I've also just noticed a ding in the corner of the chrome bezel was wondering if anyone had found a solution to this yet.? short of replacing the LCD/digitiser which like OPs phone are working fine. It's just cosmetic damage.
I once was in a bad mood and snapped a screen and backing/housing in half.I can't remember exactly,but I'm thinking the chrome bit may be part of the thin metal casing/housing that is glue taped onto the screen.
You separate the screen from the housing by using a hot air gun sparingly.
If you look back at a motherboard thread I was involved in,a person on here called Roger put up a great video tutorial link that may answer all your questions...
Sent from my GT-I9100
Ah cheers for the reply. Had a look at the mobo post you were involved in followed it to the link and coincidentally that's the exact video I watched last night. Very good video good detail and instructions. But its the black one he is stripping down so he makes no reference to the bezel which afaik is only used on the white ones.
Sent from my GT-I9100 using xda premium
I've not seen the chrome bit listed separately,so I guess its part of the metal top housing that the LCD is glued to.I've got a white one and its got a ding on it too.
You could email Samsung to see if you can get the part,but I think its not worth risking cracking the screen and you probably couldn't resuse / would get that stupid gluey tape stuff.
Sent from my GT-I9100
Appreciate it's been a while, but this seems to be the only post that matches what happened to me, so figured I'd update with my experience.
As above, dropped and dented the bezel, screen was perfectly intact, but the dent was so severe, it actually lifted a corner of my screen up. I have intentions to sell on so I wanted to fix this and pass on.
I followed this disassembly , apart from the bit about not worrying about damaging the screen as you prise it away. The housing I ordered off ebay came with a little kit, so I warmed the screen with hairdryer for a couple of minutes, then slowly prised it away, from top to bottom, inserting the tool right down the middle as the video mentions there is a large adhesive right down the middle.
Following the vid all the way to the removal of all components, this is where I ditched my current bezel/housing and reassembled into the newly ordered one. Judging by the assembly, there is no way that a bezel could be replaced without replacing the housing, it's one whole unit, and I very much doubt the build would be that drastically different for the white SGS2.
Some things to note:
Be very careful removing the vibrate motor, the connector and natural pivot point is the weakest part (new module ordered from ebay
If you are transplanting the screen like me, have some adhesive pads in your kit as most tutorials are for new screens, and as can be seen on the vid, these come with pads intact, ready to apply
Try do it in daylight
Hope that helps anyone in a similar situation.
vyks10 said:
Appreciate it's been a while, but this seems to be the only post that matches what happened to me, so figured I'd update with my experience.
As above, dropped and dented the bezel, screen was perfectly intact, but the dent was so severe, it actually lifted a corner of my screen up. I have intentions to sell on so I wanted to fix this and pass on.
I followed this disassembly , apart from the bit about not worrying about damaging the screen as you prise it away. The housing I ordered off ebay came with a little kit, so I warmed the screen with hairdryer for a couple of minutes, then slowly prised it away, from top to bottom, inserting the tool right down the middle as the video mentions there is a large adhesive right down the middle.
Following the vid all the way to the removal of all components, this is where I ditched my current bezel/housing and reassembled into the newly ordered one. Judging by the assembly, there is no way that a bezel could be replaced without replacing the housing, it's one whole unit, and I very much doubt the build would be that drastically different for the white SGS2.
Some things to note:
Be very careful removing the vibrate motor, the connector and natural pivot point is the weakest part (new module ordered from ebay
If you are transplanting the screen like me, have some adhesive pads in your kit as most tutorials are for new screens, and as can be seen on the vid, these come with pads intact, ready to apply
Try do it in daylight
Hope that helps anyone in a similar situation.
Click to expand...
Click to collapse
Hi, will the heat actually damage the screen? I saw some posts mentioning about putting it into the oven and such. It sounded very intense but if it works without damaging the screen, i might give it a try. Facing the same situation as yours. Scratches and dents all over my front chrome bezel.
Hi there,
for Years i'm reading here silently and i never register myself.
I'm German and i hope that my english is well enough that you can understand my Questions.
I have a Question, not about Software for Samsung S8, so that's the Point for me to register here.
Hope that is the right Place in this Forum for my Question.
In the Future i plan to buy a S8 second hand. My Money is small so the most second hand S8 are in need of repair (Frontglas & Backcovers). Nothing what a Human with skills can handle. But i want to mod the S8 on the Side of Hardware.
Here is my Question:
Is it possible to make a Backcover from Aluminium and to use it instead of Glascover?
My thinking is to get a Originalcover and then to rebuild one from Aluminium (Thin it must be). CNC, or Lasercut for the precision.
I've googled many hours in the Hope to find something like this, but nothing.
So i want to ask you.
I think a Backcover from Alu ist not so breakable as Glas, more stable, but is it to realize without elektrical Danger to Part of the Phone.
I don't like the Cases & Bumpers & so on. I want to make my Phone more personal.
Are my thoughts crazy, or not? What do you think?
Hope my thread here is ok and do not conflict with the Forumrules. Sorry if that happens, but otherwise i will be thankfull for an answer or discussion about this Topic.
Greets to all outhere...
Interesting idea! Personally I would go with a skin like dbrand or slikwrap even if the glass is broken. Personal look and you don't lose any wireless functionality
Make sure that you remove the wireless charging coil before this!
Aluminium Backcover-Possible or not
Hi there,
i'm living in a relativ small Town in Northern Germany, but i hope i can find some
Manufacturers that can realize my idea. Maybe i must give an Order to some Firma over Google, or so.
To j91hernandez:
Can you give me eventually some links to the products. In Germany there are unknown, i think. I want to take a look on it.
I ask myself: is a Alu-BC thick enough to protect the Phone like the Glas-BC?
Or must can i use a Metall-BC instead Alu? I don't know.
The other thing is: you must remove the Original-BC to apply the, maybe stronger, Mod-BC. But if the S8 has no Guarantee you can make it like you wish.
Glas-Cover looks great, but i've seen so much broken S8s to buy in Ebay-Second Hand Shop, so i wondering, why nobody change the BC of the Phone to avoid the use of Cases, etc.
With a well designed Metall / Alu-BC it must be better, i think. Maybe you can make it less slippery for your Hands, too.
But: is there Dangers for electrical Parts of the Phone, i mean short circuit between Parts? In wich Way it affects the NFC Functions, etc.?
Maybe try & error! I'm willing to do so if i have the Money to buy a S8. So i try to get any Infos about that Projectidea.
zoroarctic said:
Make sure that you remove the wireless charging coil before this!
Click to expand...
Click to collapse
That's a Point! The Function of the Phone shall be at 100%, so i think i must look and read about Phones with Metall-BC AND Wireless Charging how they doing it.
There would be a chance the metal backing by witch one would have to possibly custom make curves and all. But may dampen WiFi bluetooth and wireless signals. Anything other than plastic glass or aluminum I would imagine would interfere with wireless charging as well. Absorbing or warping the magnetic field
But I would say if a man could bend the edges properly a hand held rotary tool would more than likely suffice to do all edging and cutouts for various sensors. I have had to make due with home made metal object before but precision be on this is a must. As water resistance is more than like gone with the wind on this mod.....
Which I support fully
HoosierDaddy said:
There would be a chance the metal backing by witch one would have to possibly custom make curves and all. But may dampen WiFi bluetooth and wireless signals. Anything other than plastic glass or aluminum I would imagine would interfere with wireless charging as well. Absorbing or warping the magnetic field
Click to expand...
Click to collapse
I agree with this
A plastic back would make much more sense as it would bend easier than metal for the corners while allowing for wireless charging and not causing any kind of electrical shorting issues.
zoroarctic said:
I agree with this
A plastic back would make much more sense as it would bend easier than metal for the corners while allowing for wireless charging and not causing any kind of electrical shorting issues.
Click to expand...
Click to collapse
Hi there,
ok, Plastic-Cover is another idea to think about.
But it looks not so good as Alu, or Metall. Hm, maybe th use of a Skin can make the Optic cooler than. Another Sideeffekt is that the Plastik is covered then against big sctratches. No Danger for short circuits then and hopefully no problems with wireless charging and so on.
To Build such an BC is easier, right. Bending and cut out the Holes, that's all what we can make ourselves (if you are not Double-Lefthanded).
Thanks for the Input. Will think about that and trying it if i have my S8 in the Future.
A Fullbody-Cover protects the Phone completly (Front+Back), but on the other Side it is more thicker, unhandy. Often the Buttons are not good to press, and such things.
if you insist on aluminium/metal, then you are going to have to give up some functionalities. otherwise, plastics would be your only option. wood might be a viable option too, however durability would be an issue with the material.
imho though, you mentioned that you have limited money and if you're going to get an aluminium/metal/wood back cover machined by someone, it's going to cost more than you would think. replacement glass are way cheaper and as the other user suggested, you have vinyl wraps to get the look that you want