Device: LG-D325
I tried rooting, unlocking bootloader, and installing custom rom (this link).
I successfully gained root & unlocked bootloader. Than it all went down.
I flashed recovery and booted into it, using "fastboot boot recovery.img" command.
I flashed cm12.1 and after that I got the "purple screen" error.
When phone is off and I try to normally turn it on:
1st screen:
Code:
Secure booting error!
Cause: boot certification verify
2nd screen:
Code:
DemiGod Crash Handler : DBI Err Fatal!
Board Rev.: 1.0
Ram dump mode.
Option : SD card ram dump mode.
Push below files to sd card before test.
rdcookie.txt, rtcookie.txt
Please do following action.
1) Ram dump Mode. Please connect USB.
2) Get the ram dump image using QPST Configuration.
3) If sdcard ram dump enabled just wait for reboot.
4) Collect ramdump files from your pc or sdcard.
5) Send e-mail to [email protected]
The same happens when I plug in the USB cable when phone shut off.
Also, I cannot enter the fastboot menu (previously I could - before flashing CM12.1 via recovery) using volume UP + power buttons. Therefore, I cannot enter recovery.
Any info on this situation?
You need to short the test point of your phone and force the phone to qhsusb dload mode after that boot repair
it will repair your phone's download mode
And flash the phone
Br
Shahzaib Jahangir
Is there any way to fix this problem bro with out jtak
Thanks.
The test point method is not the JTAG method
razeen said:
Is there any way to fix this problem bro with out jtak
Thanks.
Click to expand...
Click to collapse
Use the test point method. It works very well and it's quite easy. But first I recommend you try "LG Flash Tool 2014" . If that works, no need to open up the phone for test point method. If you are already seeing pink screen demigod error DBI fatal error, no need to go for JTAG I think.
Feel free to ask if you need assistance for testpoint method. I have already published the method for few other people here on XDA. A little search will bring you there
my Lg325 also violet and dump mode cant flash i go to celpon repair but they cant fix my pon pls help me tnx
gilliane.08 said:
my Lg325 also violet and dump mode cant flash i go to celpon repair but they cant fix my pon pls help me tnx
Click to expand...
Click to collapse
May be I can help you. But first you need a PC, a good internet connection and patience.. If you're interested, reply me.. I will guide you how to unbrick or come out from that pink screen/demi-god screen
honeybun.1986 said:
May be I can help you. But first you need a PC, a good internet connection and patience.. If you're interested, reply me.. I will guide you how to unbrick or come out from that pink screen/demi-god screen
Click to expand...
Click to collapse
same problem here
can you help, please?
LG D325f L70
UPDATE
Now i have QDLoader 9008 (i've installed driver manually without signature). I don't know why my computer did not recognise automatically installed drivers
Else i trieb Board diag
I,ve tried QFIL QPST and recieved
/*invalid image type recieved*/
is_ack_succesfull : 1031 SAHARA_NAK_INVALID_IMAGE_TYPE
sahara protocol error
uploading image using sahara protocol failed
Before that
BoardDiag 3.99c I have an error
AP CHECK START
FAILED during loading flash programmer
There were already messages about this trouble,but there are no solution, so i am asking for it.
LGE AndroidNet USB
qhsusb_bulk
Previously i had Pink screen and Lg Pc Suite could recognize my phone
I,ve tried Format to Fat32 my inner phone emmc(i did not insert in my phone microSD card) DiskImageRev2.zip and LoaderD325.img. After format to fat32 it was 4gb.When i,ve installed loader.img it became 64mb with 2 folders in it. Device monitor showed the phone as qhsusb_bulk (i already had istalled Qualcomm drivers) After installation of LGMobileDriver_WHQL_Ver_4.0.4.exe ( 12,39 МБ )
It was recognised as LGE AndroidNet USB. (com port 3) After that i tried LgFlash tool (tot and kdz firmware,it showed error on 50%) 2014 and BoardDiag also showed error .
I can not convert it to Qualcomm HS-USB QDLoader 9008 (I saw many articles where people with qhsusb_bulk converted it to Qualcomm 9006 after installation of qualcomm drivers,but it did not works for me. Please help
Any ideas? I heared about SRK tool 2.1 Does it works for my Lg L70 D325? Or maybe QPST, or ADP
honeybun.1986 said:
May be I can help you. But first you need a PC, a good internet connection and patience.. If you're interested, reply me.. I will guide you how to unbrick or come out from that pink screen/demi-god screen
Click to expand...
Click to collapse
Please help me
My lG D325 cant on recovery and download mode. Fatal error. Who can help me
Gayan360 said:
My lG D325 cant on recovery and download mode. Fatal error. Who can help me
Click to expand...
Click to collapse
I think you are referring to the famous "purple screen" mode. Relax, that is not hard to get pass.
Follow the steps below.
But, be warned, I am not responsible for any damage caused by following these methods.
Your phone's battery has to be charged at least 50%.
You'll need a USB "data" cable.The one came with your phone is the best. Some third party cables have only power lines connected in and they will not work. So, make sure you have the "data" cable.
1. First, we have to install the necessary drivers(I am assuming that you're using a Windows PC) .
Here are the drivers. Download, install and give your PC a restart.
2. Download LG flash tool 2014 from here and extract it to your root directory(For example, drive "C " in your PC )
3. Download the firmware file for your specific phone model. In your case, as you have mentioned, it is LG D325. This is a link to a matching firmware for LG L70 D325. This file is big and its around 920MB. After download, extract the zip file to the folder where you copied the LG Flash tool 2014.
4. I hope the above mentioned steps were followed correctly and you're ready now. Remove your battery, press the power button for 5-10 seconds and then re insert the battery. press the volume up button and plug the USB cable(The other end has to be plugged in first to PC. Refer to this video if you are unclear.
5. Now launch "LG Flash tool 2014.3.exe" (right click on it and select "run as administrator" for best results).
6. Once the program is open, and click on 1 and select your kdz file which you got from the step 3. Then click either "Normal Flash(2)" of "CSE Flash".
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
7. Now another window will appear and click "Start" as in this picture.
wait until the program finishes and once done, you'll get the initial setup screen on your phone with a greeting message.
If you're still unclear, please pass a comment. Happy communicating..
Related
[FIX] Unbrick LG G2 stuck in Qualcomm HS-USB QDLoader 9008 mode
Please ensure you read these instructions a couple of times and ask questions if you have any. I myself paid for some of the tools and got it for the benefit of the community.
If all goes well and I have helped you Donate to me!
The below system is recommend : Please do not try with Windows 8.1 64 Bit or any 64 Bit OS as there may be a lot of issues we cannot clearly fix. However if you get it to work well in 64 bit windows , please write up steps , so other can benefit
PC environment
- Microsoft Windows XP (Service pack 3) 32 BIT
- Microsoft Visual C++ 2010 Redistributable Package (x86) :
Currently its looking like the LG G2 is really Unbrickable . We have had different types of failures and each failure comes with its own symptoms.
If you are stuck in the Super Brick mode of Qualcomm HS-USB QDLoader 9008 mode , this tutorial is for you.
Also if you want to force the phone into QDLoader 9008 mode , check the second post for more info.
Please NOTE. DO NOT TRY this unlesss you are 100% sure you are in Qualcomm HS-USB QDLoader 9008 mode ,
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
this is different from the qhsusb_bulk mode 9025 where you see different partitions, if you are stuck in this mode please refer to this topic to unbrick .
Download the LGG2_9008_FIX.zip View attachment LGG2_9008_FIX.zip
Updated version available : View attachment BoardDiag3.99c.zip , you could try either one of these!
Extract LGG2_9008_FIX.zip , please ensure your antivirus is off during this duration, some antivirus will detect b2b.exe as a virus.
Steps 1 : (Must be done even if you have previously extracted TOT files. This will extract the files with an mbn extension as well as, more importantly it will create a partition.txt which is crucial for this fix to work)
1. Open b2b.exe
2. At the bottom of the application "Image Extraction" Select the path to the TOT file for your Phone model.
3. Select the Dir to any Dir where you would like to extract the files to. (DIR : Selects a folder to save the images extracted from the Tot file.)
4. Click on Extract and wait, this Starts extraction.
5. On completion, “Complete” pop-up appears.
Extracted files :
Step 2: Get ready to flash.
1. On The Top of the tool , select chipset as G2 (MSM8974)
2. Select port and set it to the com port where your phone shows up as QDLoader 9008 mode in Device manager, in my case com 10.
3. Set Target Dir to the same path where you just extracted the TOT files from STEP 1 part 3 above.
Step 3: Test AP & EMMC
1. On the Top left of the Tool , select the AP check box and the EMMC check box.
2. Click on Start. This will test your AP and EMMC to ensure your phone can be fixed and there are no other HW issues.
3. Once done it should say pass under test results for AP and EMMC , circled in blue refer below.
Step 4: Test AP , EMMC & SDRAM
1. On the Top left of the Tool , select the AP check box , EMMC check box & SDRAM TEST
2. Click on Start. This will test your AP, EMMC & SDRAM to ensure your phone can be fixed and there are no other HW issues.
3. Once done it should say pass under test results for AP,EMMC & SDRAM circled in blue refer below.
Thats it , if all went well and I have helped you Donate to me! :good:
Force Phone into QDLOader 9008 mode (Only if needed)
YOU DO NOT NEED THESE STEPS IF YOUR PHONE IS ALREADY IN QDLoader 9008 mode.
If you have to force your phone into QDLoader 9008 mode please follow below, thanks to @mss1988
mss1988 said:
First of all I want to thank @george7565 for such wonderful discovery. I'm sure that many people who bricked their phone with this guide: [FIX] NO Recovery mode, No download mode, after OTA on rooted LG G2 will fix their phones just like I did.
I found short circuiting a little bit tricky, but in the end I found the way to make it.
To short circuit the capacitors I used small piece of cooper wire cut from Ethernet UTP cable.
It's important that when short circuiting is that wire ends should touch opposite sides of the capacitors.
Also the short circuited capacitors must be next to each other horizontally. See the picture below:
As you can see, depending on what is short circuited you get QDLOADER 9008 or QHSUSB mode.
So now LG G2 is INDEED UNBRICKABLE. For those who got QDLOADER 9008 mode, see the picture, fix your phones, don't waste the money on board replacements.
After I got QHSUSB mode I had further problems. Lubuntu didn't recognized my phone's mass memory partitions, it recognized it as some 2.1TB Qualcomm disk. I found the workaround, I backedup the entire nand of my working LG G2 using this method: [GUIDE] How to make a nandroid backup directly to your computer without using sdcard, then using Computer managment -> Storage in Windows 8, I deleted all phones partitions and flashed the the backup image using Win32 Disk Imager. It's important for this one that both phones are same variant and memory capacity. After that, I restored IMEI using this tool: [TOOL] Updated! 26/06/14 - EFS Professional v2.1.73 - Also for NON-Samsung devices! Also I have a problems with GPS fix, perhaps back cover position needs some tuning, I hope this guide can help, I didn't try:
Réparer en 5 minutes le GPS LG g2
Cheers
Click to expand...
Click to collapse
Here is some extra Information I got while digging around.
This app operates only in Qdload mode. Upon initial USB cable connection, do the following to send it to Qdload mode if no port or USB serial port is held.
Upon initial USB cable connection, don’t do the following if it’s already in Qdload mode.
Use either way below(#1 recommended) to connect the USB cable while the pin is grounded.
Check out the Device Manager for ports(COM or LPT). If Qualcomm HS-USB Qdloader 9008 port is activated, Qdload mode is successfully
ready to work!!
As for the USB cable, the SW download cable v2.1 (910K) for service is recommended!!
1. How to ground Boot Config switch
It may depend on models. Basically, the pin of the switch connected to Boot_config_0 or Boot_config_6 is grounded.
The circuit diagram above shows Q6000 switch’s #3 pin need be grounded.
2. How to ground EMMC SDC1_CLK resistance
It may depend on models. Basically, eMMC’s SDC1_CLK resistance is grounded.
The circuit diagram above shows R24010 need be grounded.
Hmm,my phone is shown in the device manager as LGE Android Phone,CDC Serial and CDC ECM
what should i do?
More Info on the B2BSupport LG Tool
More Info on the B2BSupport LG Tool. For anyone who wants to know more about this tool and would like to explore. It's not necessary to know the below if your only goal is to fix the phone then only the first topic of this post is needed.
Click below for more info.
Booting Problem Test
1. Select AP chipset
2. Select Com Port
3. Select Tartget Dir
4. Choose AP check
5. Choose EMMC TEST
Option Read/Write
Dump X (Dont select)
Partition X (Dont Select)
6. Choose SDRAM TEST
7. START
PMIC Test
1. Select AP chipset
2. Select Com Port
3. Select Tartget Dir
4. Choose AP check
5. Choose PMIC ON
6. START
Restore Device
1. Select AP chipset
2. Select Com Port
3. Select Tartget Dir
4. Choose AP check
5. Choose RESTORE BOOT IMAGE
- Option X (None selected)
6. START
1. AP check
- Checks out whether Qualcomm chipsets are good to see if booting works well. It’s impossible to check out
the whole functioning.
2. EMMC test
- Partition : No need to select anything. Select it to check out a certain partition.
- Option : Read Only / Read & Write (Recommended) / Erase / It can be selected while Write Only is running.
3. SDRAM test
- Checks out whether POP DDR memory is good.
4. EMMC dump
- Tick it, and selected or whole partition’s dump file is automatically created in the dump folder.
- Caution : The whole partition takes much time (24+ hours).
5. PMIC on
- Grant power to every PMIC power core rail. Tick PMIC on, and measure PMIC current to see if it’s good or not.
- Only APQ8064 is supported but not applicable to all power rails. This will be upgraded in future versions
6. Restore Boot Image
- Erases the existing terminal’s boot area and downloads a new Boot Image.
- The new Boot Image is extracted from the tot file for each model.
- Select a certain partition, and only the selected partition is downloaded. In this case, a particular image is downloadable
not just in the Boot area but also in the entire area.
- Select nothing, which is recommended as default.
7. Usage of “misc” option
- Restore device with “misc” option if LG Flash Tool fails to download displaying PID/IMEI errors.
- PID/IMEI errors during download of LG Flash Tool could happen upon using empty or erased EMMC by BoardDiag.
- <Usage>
1) make test device Qdload mode -> Run BoardDiag -> Select AP Chipset, Com Port and Target Dir
2) Select RESTORE BOOT IMAGE
3) Select “misc” like the picture
4) Click START
5) Misc image downloading takes 2~5 minutes
6) LG Flash Tool SW download again
Use2 said:
Hmm,my phone is shown in the device manager as LGE Android Phone,CDC Serial and CDC ECM
what should i do?
Click to expand...
Click to collapse
Is it Stuck at LG logo Screen ? Which Model ?
Very Well explained tutorial. :good:
G2 is completely unbricable now!! :angel:
Dammit. If this works, I will give you $20 as promised on my bounty thread.
Do you have links for the TOT files for ls980?
briankariu said:
Dammit. If this works, I will give you $20 as promised on my bounty thread.
Do you have links for the TOT files for ls980?
Click to expand...
Click to collapse
Maybe you can try this. Do confirm with the OP before flashing.
Good luck
http://storagecow.eu/index.php?dir=Xda%2FLG+G2%2FStock%2FSprint%2F
briankariu said:
Dammit. If this works, I will give you $20 as promised on my bounty thread.
Do you have links for the TOT files for ls980?
Click to expand...
Click to collapse
ZVE TOT file here: LS980ZVE_03.zip, thanks to @autoprime for the ZVE firmware share ! This is the latest greatest firmware out from Sprint for the LS980
Found a ZV7 tot file. I plan to use it on GSM and the ZVE seems to be a headache to use. downloading.....2GB...Time remaining 2hrs
---------- Post added at 01:06 PM ---------- Previous post was at 01:02 PM ----------
Will it work with the ZV7 TOT file?
It should work with ZV7.you can later update if you want
b2b sees my phone as not in dload mode. Windows 8.1 64bit
---------- Post added at 02:44 PM ---------- Previous post was at 02:43 PM ----------
Screenshot: http://i.imgur.com/ID8AHRe.png?1
briankariu said:
b2b sees my phone as not in dload mode. Windows 8.1 64bit
---------- Post added at 02:44 PM ---------- Previous post was at 02:43 PM ----------
Can you now with b2b still opened , disconnect the phone and make sure its fully off and reconnect the phone and try (Make sure the b2b app is on all the time ).
If it still says the same then you follow the below.
1. Ensure the phone is disconnected from the PC.
2. Press and hold the power button on the phone for 15 seconds (to 100% ensure the phone is powered off).
3. Start the b2b app on the PC as administrator mode
4. Now connect the phone to PC via USB cable.
Even after that if it doesn't work, you need to try with Battery connector Disconnected.
1. Ensure the phone is disconnected from the PC.
2. Open Back cover of the phone and UNPLUG the battery connecter only
3. Start the b2b app on the PC as administrator mode
4. Now connect the phone to PC via USB cable.
Click to expand...
Click to collapse
I think this is much better way to recover the phone then using QHSUSB mode.
Thanks
is this work for VS980 ?
tungkick said:
i sell 100usd tool
Click to expand...
Click to collapse
http://forum.xda-developers.com/showpost.php?p=56616839&postcount=11
11. Don’t post with the intention of selling something.
Don’t use XDA to advertise your product or service. Proprietors of for-pay products or services, may use XDA to get feedback, provide beta access, or a free version of their product for XDA users and to offer support, but not to post with the intention of selling. This includes promoting sites similar / substantially similar to XDA-Developers.com.
Hello, what about lg g2 mini? Same process?
KR
littmanr said:
Hello, what about lg g2 mini? Same process?
KR
Click to expand...
Click to collapse
That may not be supported, but try experimenting and see if one of the other options work. The G2 mini used Qualcomm MSM8226 Snapdragon 400, you could try choosing W7 G2MDS (MSM8226) . Again I don't know if this works. You could try and let us know if it did.
kryptonite said:
Can you now with b2b still opened , disconnect the phone and make sure its fully off and reconnect the phone and try (Make sure the b2b app is on all the time ).
If it still says the same then you follow the below.
1. Ensure the phone is disconnected from the PC.
2. Press and hold the power button on the phone for 15 seconds (to 100% ensure the phone is powered off).
3. Start the b2b app on the PC as administrator mode
4. Now connect the phone to PC via USB cable.
Even after that if it doesn't work, you need to try with Battery connector Disconnected.
1. Ensure the phone is disconnected from the PC.
2. Open Back cover of the phone and UNPLUG the battery connecter only
3. Start the b2b app on the PC as administrator mode
4. Now connect the phone to PC via USB cable.
Click to expand...
Click to collapse
I tried this but it don't work on L01F, can you help me? My team view information: ID: 884 430 367 Pass: 6373. Thank a lot!
buon84 said:
I tried this but it don't work on L01F, can you help me? My team view information: ID: 884 430 367 Pass: 6373. Thank a lot!
Click to expand...
Click to collapse
Dude dont post this on public, use pm instead.
If you connect your phone to the pc and see something like this
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
This guide is for you
What you will need:
1. USB cable is of decent quality (not the one on which the connection is lost at the slightest movement)
2. Windows
3. The device defined somehow Device Manager
4. The latest version of MiFlash
5. MIUI firmware developer for fastboot here
6. Adb and fastboot installer here
Theory:
If the primary boot loader (placed directly on the SoC - unkilled) can't pass control to the secondary and applied loader, the interface starts to restoration device: 9006 or 9008 mode. They differ in that the 9006 mode if the device gets lost only access to the application Loader (what we call the fastboot). It all sections of the devices are mounted in the OS and we can edit files on them or record RAW data.
In 9008 mode, you can get into if partition and entire chain bootloader (secondary and applied loader) is dead. From it anything useful we can not do: just go back to the 9006 mode (in fact in this case, have access to a low-level operations, but to describe them does not make sense). For this purpose, the device is sent to the programmer (MPRG8974.mbn) flash secondary loader (8974_msimage.mbn), after which the smartphone reboot in 9006 mode.
Restore stock partion
Add a flash-all.bat line
Code:
fastboot% * flash partition% ~ dp0images \ gpt_both0.bin
just before
Code:
fastboot% * flash tz% ~ dp0images \ tz.mbn
and flash device via fastboot.
Then u can flash again but w/o fastboot% * flash partition% ~ dp0images \ gpt_both0.bin
If device hangs on Mi logo and cant flash via fastboot / problems after re-partition / defined as QHSUSB_BULK
If you touched anything from the name of the spoiler and the previous instruction does not help, then our task will be to move into 9006 mode (if your smartphone is already defined as QHSUSB_BULK, you can go directly to the firmware).
On a device located in fastboot write in the console:
Code:
fastboot erase aboot
fastboot reboot
View attachment 3590163
Phone will remain a black screen in the Device Manager, the new device will be Qualcomm HS-USB Diagnostics 9006/9008, and Windows about 7 new flash devices. Simply close all offers their formatting. Reboot the PC (required on Windows 10, or sections will not be able to unmount when flash).
MiFlash Run as Administrator, click the button "Refresh", this will be a new device like this
View attachment 3590164
Choose the folder with the firmware, click the button "Flash". After ~ 160 seconds, the firmware is completed, to restart, hold the power button.
View attachment 3590165
If in MiFlash nothing appeared
1. Make sure that the device appears in the Device Manager, if not:
1) Connect the USB cable to the motherboard (ie "behind")
2) Put the device on charge for at least two hours and try again
Device in 9008 mode
Here things can be a little tricky, but it depends only on your particular case.
It may be necessary short-circuit test points
Possible errors in MiFlash
EE: Access is denied. (0x80070005: Dismount volume ...)
AA: Restart your laptop, connect the device to a different usb port
EE: Reached the end of the file. (0x80070026: Receiving hello packet)
AA: Need a short-circuit of the test-points, change the cable, use a different computer
Contributor
nikitaklsnkv2000
Original source
4pda
Thanks for the tip ramm...
Dr. Ramm said:
If you connect your phone to the pc and see something like this
View attachment 3590142View attachment 3590143
This guide is for you
What you will need:
1. USB cable is of decent quality (not the one on which the connection is lost at the slightest movement)
2. Windows
3. The device defined somehow Device Manager
4. The latest version of MiFlash
5. MIUI firmware developer for fastboot here
6. Adb and fastboot installer here
Theory:
If the primary boot loader (placed directly on the SoC - unkilled) can't pass control to the secondary and applied loader, the interface starts to restoration device: 9006 or 9008 mode. They differ in that the 9006 mode if the device gets lost only access to the application Loader (what we call the fastboot). It all sections of the devices are mounted in the OS and we can edit files on them or record RAW data.
In 9008 mode, you can get into if partition and entire chain bootloader (secondary and applied loader) is dead. From it anything useful we can not do: just go back to the 9006 mode (in fact in this case, have access to a low-level operations, but to describe them does not make sense). For this purpose, the device is sent to the programmer (MPRG8974.mbn) flash secondary loader (8974_msimage.mbn), after which the smartphone reboot in 9006 mode.
Restore stock partion
Add a flash-all.bat line
Code:
fastboot% * flash partition% ~ dp0images \ gpt_both0.bin
just before
Code:
fastboot% * flash tz% ~ dp0images \ tz.mbn
View attachment 3590159
and flash device via fastboot.
Then u can flash again but w/o fastboot% * flash partition% ~ dp0images \ gpt_both0.bin
If device hangs on Mi logo and cant flash via fastboot / problems after re-partition / defined as QHSUSB_BULK
If you touched anything from the name of the spoiler and the previous instruction does not help, then our task will be to move into 9006 mode (if your smartphone is already defined as QHSUSB_BULK, you can go directly to the firmware).
On a device located in fastboot write in the console:
Code:
fastboot erase aboot
fastboot reboot
View attachment 3590163
Phone will remain a black screen in the Device Manager, the new device will be Qualcomm HS-USB Diagnostics 9006/9008, and Windows about 7 new flash devices. Simply close all offers their formatting. Reboot the PC (required on Windows 10, or sections will not be able to unmount when flash).
MiFlash Run as Administrator, click the button "Refresh", this will be a new device like this
View attachment 3590164
Choose the folder with the firmware, click the button "Flash". After ~ 160 seconds, the firmware is completed, to restart, hold the power button.
View attachment 3590165
If in MiFlash nothing appeared
1. Make sure that the device appears in the Device Manager, if not:
1) Connect the USB cable to the motherboard (ie "behind")
2) Put the device on charge for at least two hours and try again
Device in 9008 mode
Here things can be a little tricky, but it depends only on your particular case.
It may be necessary short-circuit test points
Possible errors in MiFlash
EE: Access is denied. (0x80070005: Dismount volume ...)
AA: Restart your laptop, connect the device to a different usb port
EE: Reached the end of the file. (0x80070026: Receiving hello packet)
AA: Need a short-circuit of the test-points, change the cable, use a different computer
Contributor
nikitaklsnkv2000
Original source
4pda
Click to expand...
Click to collapse
Thanks man u are truly
Savior of mine MI4
Thanks a lot
Tell me how to flash fastboot rom on extended partition... My device got bricked when I tried to flash miui7 mm on extended using twrp....plz help
Nice share bro. Thanks
mad-extrem said:
Tell me how to flash fastboot rom on extended partition... My device got bricked when I tried to flash miui7 mm on extended using twrp....plz help
Click to expand...
Click to collapse
There is no difference between stock or extended partition, in flashing fastboot rom using MiFlash! It will recreate whole partition table!
Just follow steps in OP
Inviato dal mio D6633 utilizzando Tapatalk
mad-extrem said:
Tell me how to flash fastboot rom on extended partition.
Click to expand...
Click to collapse
U mean MM merged partition? IDK, which error show MiFlash?
If error: 0x80004005: FAILED (remote partition table doesn't exist).
then use this tutorial
Bricked my Mi3 and seeing lots of drive when connected to PC. trying to follow this guide.But link to download "MiFlash" not working. any Mirrors ?
EDIT : Solved it using this Guide.. Thanx a lot !!!!
It worked, thanks allot
Sir, I have bricked my mi3. I am not actually understanding how to follow this tutorial..Please give me some help...
vaski123 said:
Sir, I have bricked my mi3. I am not actually understanding how to follow this tutorial..Please give me some help...
Click to expand...
Click to collapse
What do you not understand?
You have to flash a fastboot rom, with MiFlash, that will re-build partition table
Inviato dal mio D6633 utilizzando Tapatalk
That will erase internal stoarge (sd card too). I lost everything on stored on it.. ?
i have my mi4 stuck on fastboot mode, and every time i try to flash a rom with miflash it shows the message "remote partition table doesn´t exist" y have tryed your method but it didnt fix the problem. Do you know why?
marlo125 said:
i have my mi4 stuck on fastboot mode, and every time i try to flash a rom with miflash it shows the message "remote partition table doesn´t exist" y have tryed your method but it didnt fix the problem. Do you know why?
Click to expand...
Click to collapse
Check post #7, if you read all (just less than 2 pages) you could find the solution by yourself.
Inviato dal mio D6633 utilizzando Tapatalk
Thank you for you sharing your knowledge I am very grateful I ran into this post and was able to repair my mi3. :good:
thanks sir, you saved ma life,thanks once again
You are my saviour
thanks for tutorial
a.broken.star said:
Bricked my Mi3 and seeing lots of drive when connected to PC. trying to follow this guide.But link to download "MiFlash" not working. any Mirrors ?
EDIT : Solved it using this Guide.. Thanx a lot !!!!
Click to expand...
Click to collapse
hey could you or anyone else help me with this...i bricked my phone and not able to boot into recovery and fastboot mode..its just completly dead...i am downloading miflash and fastboot room for my device[mi3]...plz help
Sir I Have followed your instructions because my problem is having having a Partition does not exist error in mi flash. i was already in the MiFlash step when suddenly the there was an error Access Denied and i keep receiving an error saying USB not recognized. Please help me any workaround Sir my mi3 no longer turns on and it no longer detected to a computer
For a week now,i have been trying to troubleshoot these issues and they ended up in vain.
The problem occurred,when i first tried to flash CM recovery ,i Typed in "FASTBOOT oem unclock",then everything went into this havoc.
The the phone ,boots into Fastboot mode Only when i press the (Vol Urip+power).
No recovery is Present ,when i try the (Vol Down + Pwer) I get the One plus symbol ,nothing else.
No Rom is present ,so i cant just load into a Rom ,to try something via that way
The images show a few ways that i have tried to solve this.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Since i am NOT able to go into recovery ,i am stuck.
Please try helping me solve this ,Thanks !
[The methods that i have previously tried before asking this is ,
Tried to use the WinDroid Toolkit ,almost a couple other threads regarding bootloop(since i am unable to get the Recovery screen itself) all that didn't help]
Edit: If above links of image don't load
http://postimg.org/image/awmyeceiz/
http://postimg.org/image/iulytqh6z/
arundp95 said:
For a week now,i have been trying to troubleshoot these issues and they ended up in vain.
The problem occurred,when i first tried to flash CM recovery ,i Typed in "FASTBOOT oem unclock",then everything went into this havoc.
Click to expand...
Click to collapse
Ok, try this
still stuck.
Thanks for the tip.
I tried that method and this is wher i am stuck at.
When i connect the phone instead of getting Qualcomxxxxx i get RELINK HS-USB QDLOADER 9008(com3)
and because of this the msm downloader,doesnt detect the phone and its stuck there.
Please help.
Thank You
arun
[Solved]
It finally got detected then stated up .
[if anyone gets stuck with this problem,i am more than willing to help you solve it .Ping me ]
Thank you
arun
arundp95 said:
It finally got detected then stated up .
[if anyone gets stuck with this problem,i am more than willing to help you solve it .Ping me ]
Thank you
arun
Click to expand...
Click to collapse
Do mention here. It will be helpful for everyone.
[Solved] OnePlus X Brick
saurabh40629 said:
Do mention here. It will be helpful for everyone.
Click to expand...
Click to collapse
Sure.
As the Post above mentioned (in the first comment) ,thats the way to go to fix a Hard bricked / bootloop stuck / no Display.
But if you encounter any problems or issues like i did (the QualCom 9008 ...).I did these
Note : all downloads for this adventure are already present in that guide ,Give it a thumbs up after you fix it as it just recovered a potato , link
HTML:
http://forum.xda-developers.com/oneplus-x/general/guide-mega-unbrick-guide-hard-bricked-t3272108
Step 1: Requirements
Download the qualcom drivers,fastboot-adb all of that,even though i had them installed,i did a clean installation.
Download the Huge 800MB file (the Recovery tool).
Unzip them to the Desktop, 2 folders (1 for the Qualcomm driver,another for the msm).
Step 2: Set-up
Follow the turning off drive signature process from the post above ,Its fairly simple(press shift restart,advanced,f7 restart).
Install adb-drivers.
Switch off phone (press Power Button for 12 sec or so )till it vibrates and display is blank.
Press the Power Up button and plug in the Phone to your comp
If your Internet connection is turned on,mostly windows will itself download and install the driver(qualcom-xxx) for this device.
Step 3:
Now Unplug the phone.Switch it off(your display will be blank ,to begin with but remove phone press power button 12 sec (wait for vibrate )
Press power button up and plug it back in the comp.When you do this navigate to the Device manager tab ,A new entry in that table will be present Ports & Coms or so. If you dont have this ,no worries (go back to the First step and try to get your drivers re-Installed) .
Now that you have located your com port, RELINK HS-USB QDLOADER 9008(com3) in my case( you might have anything else ,but getting this is crucial).
On that Entry right click and go to Properties.In properties > Driver Tab > Update Driver
Once you click Update, Click on Browse my comp for driver
Then Click on LET ME PICK FROM A LIST
UNCHECK the SHOW COMPATIBLE HARDWARE // Have to do this !
Under Manufacturer,FIND Qualcomm Incorporated
Under MODEL,Select QUALCOMM HS- USB MSM DIAGNOSTICS xxxx (i chose the first entry,BUT MSM is integral).
Install that .RESTART COMP,IT'll PROMPT.
UNPLUG PHONE ,SWITCH OFF ,Press POWER UP+ for 12sec
Reconnect to the comp ,now your DEVICE MANAGER will show your port ENTRY as QUALCOMM HS-USB MSM DIAGNOSTICS
Click on that entry and Click on Properties > Driver >Update >Browse my comp >
Now select the folder in which you have downloaded the Qualcomm drivers x64 or x86 (from the post above ,you should have downloaded them in the beginning).
Now install that , If it asks for an Restart COMP ,RESTART comp( i restarted,just to be safe).
Step 4 : Completion
Connect the phone in fastboot mode(Just the power up+ & connect )
msm.exe > open in admin mode.
Open up the MSM.exe in the folder (the big file that you downloaded earlier the 800MB one )
It will recognize your device,If it doesn't.
Unplug Phone.
Power Off
Power Up+ ,wait 10sec ,and Plug in ,(hold the power up)
MSM.exe will recognise your device, Try to click start on that and see if it triggers it ,else just close and reopen msm.exe
Your device will be recognised Press Start, it'll do the rest.
After all this,a recovery mode will show up,click yes/ no and Continue.
That's all.OnePlus X good as new
arun.
arundp95 said:
Sure.
That's all.OnePlus X good as new
arun.
Click to expand...
Click to collapse
Let's hope someone finds this useful in future. Thanks for the detailed steps to recover the phone.
arundp95 said:
Sure.
As the Post above mentioned (in the first comment) ,thats the way to go to fix a Hard bricked / bootloop stuck / no Display.
But if you encounter any problems or issues like i did (the QualCom 9008 ...).I did these
Note : all downloads for this adventure are already present in that guide ,Give it a thumbs up after you fix it as it just recovered a potato , link
HTML:
http://forum.xda-developers.com/oneplus-x/general/guide-mega-unbrick-guide-hard-bricked-t3272108
Step 1: Requirements
Download the qualcom drivers,fastboot-adb all of that,even though i had them installed,i did a clean installation.
Download the Huge 800MB file (the Recovery tool).
Unzip them to the Desktop, 2 folders (1 for the Qualcomm driver,another for the msm).
Step 2: Set-up
Follow the turning off drive signature process from the post above ,Its fairly simple(press shift restart,advanced,f7 restart).
Install adb-drivers.
Switch off phone (press Power Button for 12 sec or so )till it vibrates and display is blank.
Press the Power Up button and plug in the Phone to your comp
If your Internet connection is turned on,mostly windows will itself download and install the driver(qualcom-xxx) for this device.
Step 3:
Now Unplug the phone.Switch it off(your display will be blank ,to begin with but remove phone press power button 12 sec (wait for vibrate )
Press power button up and plug it back in the comp.When you do this navigate to the Device manager tab ,A new entry in that table will be present Ports & Coms or so. If you dont have this ,no worries (go back to the First step and try to get your drivers re-Installed) .
Now that you have located your com port, RELINK HS-USB QDLOADER 9008(com3) in my case( you might have anything else ,but getting this is crucial).
On that Entry right click and go to Properties.In properties > Driver Tab > Update Driver
Once you click Update, Click on Browse my comp for driver
Then Click on LET ME PICK FROM A LIST
UNCHECK the SHOW COMPATIBLE HARDWARE // Have to do this !
Under Manufacturer,FIND Qualcomm Incorporated
Under MODEL,Select QUALCOMM HS- USB MSM DIAGNOSTICS xxxx (i chose the first entry,BUT MSM is integral).
Install that .RESTART COMP,IT'll PROMPT.
UNPLUG PHONE ,SWITCH OFF ,Press POWER UP+ for 12sec
Reconnect to the comp ,now your DEVICE MANAGER will show your port ENTRY as QUALCOMM HS-USB MSM DIAGNOSTICS
Click on that entry and Click on Properties > Driver >Update >Browse my comp >
Now select the folder in which you have downloaded the Qualcomm drivers x64 or x86 (from the post above ,you should have downloaded them in the beginning).
Now install that , If it asks for an Restart COMP ,RESTART comp( i restarted,just to be safe).
Step 4 : Completion
Connect the phone in fastboot mode(Just the power up+ & connect )
msm.exe > open in admin mode.
Open up the MSM.exe in the folder (the big file that you downloaded earlier the 800MB one )
It will recognize your device,If it doesn't.
Unplug Phone.
Power Off
Power Up+ ,wait 10sec ,and Plug in ,(hold the power up)
MSM.exe will recognise your device, Try to click start on that and see if it triggers it ,else just close and reopen msm.exe
Your device will be recognised Press Start, it'll do the rest.
After all this,a recovery mode will show up,click yes/ no and Continue.
That's all.OnePlus X good as new
arun.
Click to expand...
Click to collapse
Hi Saurabh40629/ arundp95
that 800mb link may be expired. unable to download the file.could you please share the new link. it'll be really helpful for me.
I am trying to resolve this from last week unable to get that file.
Please Help!!!!!!!
Hi vinesh ,
Did you got the 800mb recovery tool link
A couple days back I bricked my G3 so I tried many things but nothing seemed to work, then I found R-T-B’s guide, and it worked, it can unbrick any G3 Vs985.
I highly suggest you to read the complete guide before proceeding and you must ignore the instructions.txt file included in the Unbrick Kit folder.
I am just writing this, the tools are from @R-T-B
Say thanks to that guy and if you like please donate.
Disclaimer: I’m not responsible for anything, use it on your responsibility
What is Hard Brick?
When your has no power, no sign of life, no indication whether plugged or not, sometimes vibrates when plugged in usually stays at black screen aka dead, LED changes color.
To Put Your Phone in Qualcomm USB mode:
If connected to PC Device Manager recognizes as LGE Android Mobile Usb which isn’t a good sign means you going to have to Short Pin via test point.
Open your phone and take out the battery. Remove the top half of the phone housing. You do not need to remove the bottom half by the usb. Also you don't need to remove the screw next to the camera. If you do remember that it is a different size so keep it separate.
2. You will see a big metal shield. You need to remove it. It is pretty easy just pry it off and it pops back into place when you are done.
3. Next you need to short the pins as shown in the following picture with a small thin, stiff metal wire. While continuing to short the pins plug in your usb cable. You should hear windows detect the phone almost instantly. Keep shorting the pins for the count to 5 and then you can release the wire. See image below, ignore the ethernet connector.
Shorting means just attaching those two points with a small thin, stiff metal wire for 5secs or so.
4. Now open device manager in windows and it should show your phone under com ports as Qualcomm 9008 (COM #). If it doesn't try the process over again. When it does work remember this number. It is going to be used later.
5. When your phone has detected as Qualcomm usb then release the shorting points.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Now you’re ready for resurrection of your beloved LG G3
Pre-requisites:
All you need is in this Unbrick Kit, it’s a pretty big file, download, be patient.
Download it here:
md5:
c2a9cff174ed0d4a1c218023087d10cc
Qualcomm QDLoader_HS-USB_Driver 32 and 64bit
LG_Verizon_Drivers
LGUnitedMobileDriver
Note: Only install 32bit or 64bit drivers of Qualcomm, don’t install both
Procedure:
Make sure your phone is in Qualcomm 9008 mode note the com port # in Device Manager
If you are on a 64 bit system you will need to disable driver signing. Here is how:
Step 1. Open the Windows command prompt as “Run as Administrator”.
Step 2. Run
Code:
bcdedit -set loadoptions DISABLE_INTEGRITY_CHECKS
Step 3. To finalize the process run
Code:
bcdedit -set TESTSIGNING ON
Or you can simply disable driver signing by pressing F8 before Windows logo appear when it’s booting.
Step 4. Reboot and you’re done.
Connect your phone w/o battery and run BoardDiag from folder “v2.99” inc. in Unbrick kit
And be sure the AP check and EMMC are checked, select AP chipset as B2 (MSM8974AC), check Qualcomm’s port # from Device Manager and put it in BoardDiag’s ComPort box, see image below:
Now click start and wait for test to complete, if that does not work, try unchecking the EMMC test. If that still does not work, use the BoardDiag in v3.99c folder and also try it without EMMC test.
If it throws an error about not being in dload mode you need to restart the shorting process. Hold the short for a bit longer this time.
Now check RESTORE BOOT IMG and choose “aboot” from drop down menu and again click start
Do the same for following partitions FOLLOW THE ORDER!!
BackupGPT
boot
dbi
laf
PrimaryGPT
recovery
rpm
tz
Now flash “sbl1”. Always flash “sbl1” at the end to prevent super brick.
Phone should now get disconnected.
Remember your phone is connected w/o battery till this point.
Now disconnect from PC and put in the battery
Hold Volume Up button and connect to PC while holding Volume Up button, Congrats you’re in download mode. Now use LG Flash Tool 2014 included in Unbrick Kit.
Run it As Administrator, see image below.
You’ll see this window after clicking CSE Flash, hit enter.
Now it will Stop Responding at 99 percent, happened to me, so I assume it’s just a bug in the program. Don’t worry it’s still going to install the software in your LG G3
Do not remove usb/unplug phone till your phone restarts.
NOTES: If you get an error about a dll missing you need to download and install the following: Download
Now your running 47A Android MM
Hope that this helps, also if you find any problems or need help please post so I can update this post.
Feel free to comment and help me to improve this guide.
The guide is attached as 7z for convenience ...
Thanks..
I seem to have bricked my wife's vs985 trying to flash jasmine ROM. Can get it to qualcomm mode but it keeps failing the eemc test at sbl1. I'll run through the guide a few more times tomorrow but its really being a pain. First the WiFi disappeared and it started acting crazy. Could be its time to go even with the new battery I purchased.
Update:
I managed to flash every file that was mention with the exception of System and User Data. Tried to power on and nothing.
I did that for some odd reason jumping the pins isn't necessary and the device populates automatically when connected to USB. I tried running KDZ but nothing. I can try and run the TOT but, I'm a bit skeptical. As of this moment I have successfully erased the eMMC but when testing it always finds some reason to fail the test.
I'm able to write with APC and Restore Boot IMG selected and as of this moment managed to get the system image re-flashed. I'm in the process of loading the User data which is about 11Gb so it'll take awhile. I still have sbl1 at the end to flash. I will note that when I did jump the pin to ground it would always fail sbl1 or load a partition.txt doesn't exist error. I extracted the TOT as directed but it just kept throwing the same error.
I did also notice when the battery is in and the usb connected it is not recognized by my PC.
very good tutorial
"partition.txt doesn't exist"
Is nowhere to be found. What can I do?
Thanks Almighty God and you alich3451, so much for this guide. My VS985 was bricks. No download, no recovery mode, black screen and the led blinks red and blue continuously when plunged. I toiled for for many researches and guides but all never worked, except this one.
Yes, I really followed the steps critically got the phone back from dead to life.
Through my experience i want to recommend the battery in before the flashing of the TOT file begins . Secondly, do not check the devices manager for the port number but ratter check and watch closely the right conner of the taskbar for the pop up messages with the port number written at the end of the message during the installing of your driver by your windows 7 PC when you plug in the phone with the battery inside. That is the port number you have to take note and use it in Com Port area of BoardDiag v2.99a during the flash of the TOT partitions.
With this added to the main guide above you should get everything working normal.
Thanks alich3451 !!
Do I need to short the pins & stuff if I get into Download Mode already? My Phone is getting shown as LGE AndroidNet USB Serial Port (COM4) is that alright?
Need help please!!!
while i managed to reach up flash tool step where it stack so i had to start all over again but this time i cant even pass the first step.
I successfully sort the pins every time and after i do a successful test with BoardDiag (without emmc) and i get pass message after a few seconds its disconnects and i cant move to the rest steps.
what iam doing wrong ?
Lg Mobile Flash tool
Hello,
after I hit start on the flash tool, it opens up another lg tool that tries to download stuff from the internet. Then my stuff fails
I have G3 D858HK, when i use my current .tot file. It won't boot into download mode. When i use your model file, it successfully boot :3
Is my file corrupt?
there are too many people have bricked their device. so here is the guide on how to debrick your device.
1. download the factory firmware ,uncompresss to your local disk. links : http://pan.baidu.com/s/1bC1tJw ; direct link from my server: https://tenfar.com/usr/uploads/nexus6p_fix_bricked.zip .use baidu disk .if you can. bandwidth limited.
2. download the EDL mode drivers ,and install to your pc. links: https://pan.baidu.com/s/1bpHPXE3
3. download miflash http://api.bbs.miui.com/url/MiFlash and install in your pc
4. run the miflash program and select the firmware ,plug in your phone to usb cable. in pc's device manager it will show the 9008 com port.
5.in miflash will show the com port,click flash,wait for it to finished
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Edited:
How to enter EDL mode:
1 your device is bricked ,stuck in edl mode.try reset your device before flashing with miflash
2 flash a customize boot from cyanogemod or lineage.
Code:
adb reboot edl
3 unlocked phone with fastboot commands ,try this https://forum.xda-developers.com/ne...l-bootloader-extra-commands-nexus-6p-t3564086
4 unlocked phone using fastboot commands to erase sbl1
Code:
fastboot erase sbl1
not recommended
5 erase your sbl1 with dd commoand not recommended
Code:
dd if=/dev/zero of=/dev/block/platform/soc.0/f9824900.sdhci/by-name/sbl1 bs=16384
can you upload to androidfilehost links, not able to download from there.
also is that a normal firmware or special one?
Same here, first link is not working. Is it the standarg Google Factory Image or is it something different?
The Bootloader must be unloked?
I see the following under Device Manager when I connect my Nexus 6P to a Windows 10 Desktop via USB C:
Qualcomm HS-USB QDLoader 9008 (COM3)
I have installed the Mi Flash Tool as above along with USB drivers and Qualcomm drivers. I am not able to flash any factory firmware, however. I receive an error stating that the "hello packet" could not be received followed my an object reference error. I have tried many versions of the Mi Flash Tool to no avail.
Any other suggestions are much appreciated.
Thanks.
catalase said:
I see the following under Device Manager when I connect my Nexus 6P to a Windows 10 Desktop via USB C:
Qualcomm HS-USB QDLoader 9008 (COM3)
I have installed the Mi Flash Tool as above along with USB drivers and Qualcomm drivers. I am not able to flash any factory firmware, however. I receive an error stating that the "hello packet" could not be received followed my an object reference error. I have tried many versions of the Mi Flash Tool to no avail.
Any other suggestions are much appreciated.
Thanks.
Click to expand...
Click to collapse
power off your device with pressed the power key for 30 seconds. if the EDL mode is not in the right state .it will said send hello packet errors.
this firmware is flashed with qcom's firehose protocol. it needs the device in the right firehose state.
@tenfar Can u update to the another host so we can easily download? That's will be great.
@tjchuot287 you can download "nexus6p_fix_bricked" firmware using "Advanced Download Manager" ADM on PlayStore using its built-in browser with "desktop mode" enabled...
Worked for me...
Hope that helps...
@5.1 I mean that i cannot download "USBdriver_8916.zip", but i think i will find it on google and download it instead. Hope it works.
@tjchuot287
I used advanced download manager and both downloaded fine... Since then far already shared the firmware from his server, It's likely he'll provide an alternative link for the driver as well... :good:
@5.1 does it unbricked your phone? Im kind of desperate
Well, I didn't use it... Since my phone is working. :angel:
I guess tenfar wouldn't have posted it if it didn't work. :good:
anyway, how to enter to EDL mode?
tenfar said:
power off your device with pressed the power key for 30 seconds. if the EDL mode is not in the right state .it will said send hello packet errors.
this firmware is flashed with qcom's firehose protocol. it needs the device in the right firehose state.
Click to expand...
Click to collapse
I press the power key for 30 seconds with the USB C cable attached to the computer and the computer does emit a tone as if the phone has been disconnected and the device manager continues to show the Qualcomm HS-USB QDLoader 9008 (COM3). However, I still receive read packet error.
Do you have any other suggestions on how to get it into the correct EDL mode or the correct firehose state?
UPDATE:
[0.00 COM3]:[COM3]:start flash.
[0.00 COM3]:received hello packet
[0.00 COM3]:can not found programmer file.
Hello packet is recevied. However "can not found programmer file" is returned. Programmer file prog_emmc_firehose.mbn is in the extracted contents nexus6p_fix_bricked.zip, however the Mi Flash Tool does not recognize.
tjchuot287 said:
anyway, how to enter to EDL mode?
Click to expand...
Click to collapse
A few posts above yours...:
tenfar said:
power off your device with pressed the power key for 30 seconds. if the EDL mode is not in the right state .it will said send hello packet errors.
this firmware is flashed with qcom's firehose protocol. it needs the device in the right firehose state.
Click to expand...
Click to collapse
@5.1 thank you, I really appreciate your helps, but i think my phone is dead now. I didnt unlock bootloader before so now i cant do anything. Poor me
I'm having the same "cannot receive hello packet" error. I tried to old down the power until the device is re detected in device manager, but it still does the same.
catalase said:
I press the power key for 30 seconds with the USB C cable attached to the computer and the computer does emit a tone as if the phone has been disconnected and the device manager continues to show the Qualcomm HS-USB QDLoader 9008 (COM3). However, I still receive read packet error.
Do you have any other suggestions on how to get it into the correct EDL mode or the correct firehose state?
UPDATE:
[0.00 COM3]:[COM3]:start flash.
[0.00 COM3]:received hello packet
[0.00 COM3]:can not found programmer file.
Hello packet is recevied. However "can not found programmer file" is returned. Programmer file prog_emmc_firehose.mbn is in the extracted contents nexus6p_fix_bricked.zip, however the Mi Flash Tool does not recognize.
Click to expand...
Click to collapse
select the file in advance settings in miflash
从我的 iPhone 发送，使用 Tapatalk
tjchuot287 said:
@5.1 thank you, I really appreciate your helps, but i think my phone is dead now. I didnt unlock bootloader before so now i cant do anything. Poor me
Click to expand...
Click to collapse
I'm not sure this procedure require an unlocked bootloader. However @tenfar may certainly shed some light on this matter...
Hoping you get it sorted though...
Still getting "cannot receive hello packet" error. @tenfar a couple of questions:
- If the phone is detected in Device Manager as "Qualcomm HS-USB QDLoader 9008 (COMx)" do I still need to install the drivers from step 2?
- Do I need a particular combination of power, vol +/- in order to put the phone in the right EDL mode?
When I hold the power button for few seconds, the PC it is connected to makes the standard tone when a USB device is plugged/unplugged, but device manager still show the same device and Miflash still gives me the error when I flash.
Thanks for all the help BTW