[Kernel]Extreme kernel for canvas HD a116 - Micromax A116

Code:
*** Disclaimer
I/XDA am/is not responsible for any kind of damage to your device,
or in case it explodes, your surroundings.
Please use it at your own risk!
Features :
Based on Phoenix kernel 1.0 by neomanu
Quote:
Thundercharge control 2.1
dram controller overclock by 10 mhz
mediatek wifi power management
Compatible with MTK KitKat ROMs (eg. Discovery ROM(Untested), CM11 NxtGen(Tested), Optimus(Tested)).
Will not work with JB(4.2) ROMs.
-O3, Cortex-A7, NEON, VFPv4 optimizations.
Compiled from arm-linux-androideabi 4.7 Toolchain
Asynchronous Fsync ported from HTC Devices.
Dynamic Fsync v1.5
Added cdrom option to UMS-lun-devices .
PowerSuspend driver support (replaces EarlySuspend)
Android early_suspend/late_resume PM kernel driver framework has been
deprecated by Google. This new powersuspend PM kernel driver is a replacement
for it.
Conserves battery much better.
Sweep2Wake, Sweep2Sleep
DoubleTap2Wake
Intelli_plug driver.
Intelligent hotplug cpu driver with eco mode.
Reduced debugging = More performance.
Patches from NVIDIA to improve power efficiency.
GPU frequency set to 500MHz.
Bugs :
Quote:
1. Camera not working (CM11 NG) (Library patches fix this on A116)
(Working with Optimus on A116)
Please do report any, if found.
Installation :
Make a full/Nandroid backup of your current ROM.
Place the kernel zip in internal/external sdcard and reboot to recovery.
Perform factory reset (format system, cache, data) after backup
Install kernel zip and reboot!
FAQ :
Quote:
Will this work on all MT6589 Phones?
A: No, only A116 and its clones (MyPhone A919i, Wiko Cink 5, Fly IQ451).
Do not try it on another phone, unless you want to brick it.
How to use doubletap2wake and sweep2wake?
A: Refer post #3.
Is this kernel compatible with CM11 NxtGen?
A: Yes. But you have to change the ramdisk.
How do I change the ramdisk?
A: http://forum.xda-developers.com/show...&postcount=525
Why is the kernel size bigger?
A: This is due to the -O3 optimiztion.
It results in faster but slightly bigger code.
Recomended app for kernel control:-
kernel auditor,thunderzap control for mediatek power management tool.
Downloads:-
https://drive.google.com/file/d/0B2g-iK0TdiioTGM5SFlhaXVQZEU/view?usp=sharing
Credits:-
@neomanu for kernel base
@varun.chitre15 for thundercharge control
Source Code: https://github.com/Yrahate7/canvas_hd_extreme

stuck on boot logo
my rom is green marshmallow (4.4.2)
wat now

sandyss18 said:
stuck on boot logo
my rom is green marshmallow (4.4.2)
wat now
Click to expand...
Click to collapse
Re-flash your Rom & change the ramdisk

Ok
---------- Post added at 07:58 AM ---------- Previous post was at 07:57 AM ----------
Jow to change ram disk
Link given is not working

sandyss18 said:
Ok
---------- Post added at 07:58 AM ---------- Previous post was at 07:57 AM ----------
Jow to change ram disk
Link given is not working
Click to expand...
Click to collapse
Give me your boot.img

leo.riv said:
Give me your boot.img
Click to expand...
Click to collapse
Thabjs buddy
Attached boot. Img of my rom

sandyss18 said:
Thabjs buddy
Attached boot. Img of my rom
Click to expand...
Click to collapse
Modified boot.img
View attachment boot.img

leo.riv said:
Modified boot.img
View attachment 3870507
Click to expand...
Click to collapse
man u r really prompt in replying
thanks a lot
i will get back after flashing
jus to make sure, i have to merge this boot.img (new) with ROM n flash n then flash ur kernel.zip

sandyss18 said:
Thabjs buddy
Attached boot. Img of my rom
Click to expand...
Click to collapse
First of all link is not working bro
And that modified boot img is of what phone
Anyways, good job bro

Maxz21 said:
First of all link is not working bro
And that modified boot img is of what phone
Anyways, good job bro
Click to expand...
Click to collapse
Ok its of green marshmallows. Hehehe sorry guys for the stupid question

Friends Port to this kernel for miui 8, in advance thank you very much.

Can I ask? After I flash this Kernel, my boot screen has stop loading. Can you help me? I'm using MIUI 8 6.8.4. Thank you

markfafafaFive said:
Can I ask? After I flash this Kernel, my boot screen has stop loading. Can you help me? I'm using MIUI 8 6.8.4. Thank you
Click to expand...
Click to collapse
Change the ramdisk

Related

[CM11][KERNEL] FirSt [CM11 commits till:15-2-15]

FirSt is my first custom kernel for any device.
I will be adding more features to it in future releases.
Till now it is working great with no issues.
Features:
1. Based on latest CyanogenMod kernel source with new camera libs, charging bug fixed, touchscreen and proximity commits.
2. Intelli_plug 3.9
3. Intelli_thermal 3.0
4. Simple gpu algorithm
5. Power suspend
Instructions:
1. Custom recovery needed.
2. Download FirSt Kernel
3. Reboot to recovery.
4. Choose install from so card and flash the zip.
5. Download faux kernel enhancement app and enable intelli_plug and intelli_thermal.
Credits:
XDA, google, CyanogenMod, faux123, santosh m
Kernel Source:
FirSt Kernel
XDA:DevDB Information
FirSt Kernel, Kernel for the YU Yureka
Contributors
Sudeep Duhoon
Kernel Special Features: Faux intelli_plug, intelli_thermal, simple gpu algorithm, power suspend, latest cm source based
Version Information
Status: Beta
Current Beta Version: 1
Beta Release Date: 2015-02-17
Created 2015-02-16
Last Updated 2015-02-16
Reserved
Which charging bug dude???
Sent From My Yureka
what is the charging time ?>
with xcelerate kernel im getting more than double the charging speed.. and also battery backup..
freakzapster said:
Which charging bug dude???
Sent From My Yureka
Click to expand...
Click to collapse
Battery doesn't reach 100%
Kiran Anto said:
what is the charging time ?>
with xcelerate kernel im getting more than double the charging speed.. and also battery backup..
Click to expand...
Click to collapse
Edit:I confirm that battery charging is same as xcelerate.
does it have any other governors.. other than the stock ones ??
also any new features...
is it able to shut down cores.. when not in use.
in my friends moto g,.. when not in heavy use only one core works.. and others go offline. when viewed in cpuz
but for mine. always all the 8 cores are running that too at above 499 Mhz....
Kiran Anto said:
does it have any other governors.. other than the stock ones ??
also any new features...
is it able to shut down cores.. when not in use.
in my friends moto g,.. when not in heavy use only one core works.. and others go offline. when viewed in cpuz
but for mine. always all the 8 cores are running that too at above 499 Mhz....
Click to expand...
Click to collapse
Features are mentioned in the post.
Yes.
thank you ..
---------- Post added at 08:33 AM ---------- Previous post was at 08:32 AM ----------
can you upload the kernel in xda.. cant download from dev-host..
Good work.....
Nice work
Sudeep Duhoon said:
Features are mentioned in the post.
Yes.
Click to expand...
Click to collapse
bro
could u guide me how to suspend the power of remaining cores when not in use.
TechnoTrons said:
bro
could u guide me how to suspend the power of remaining cores when not in use.
Click to expand...
Click to collapse
Use faux kernel enhancement app.
Go to cpu hotplug
Enable intelli_plug
Set to eco performance.
Sudeep Duhoon said:
Use faux kernel enhancement app.
Go to cpu hotplug
Enable intelli_plug
Set to eco performance.
Click to expand...
Click to collapse
Thanks
Sent from my AO5510 using XDA Free mobile app
i cant download from d-h.st .. please find someother way....
Sudeep Duhoon said:
Battery doesn't reach 100%
Edit:I confirm that battery charging is same as xcelerate.
Click to expand...
Click to collapse
Can I flash this kernel in stock CM11 which was shipped along with Yureka?
---------- Post added at 06:00 PM ---------- Previous post was at 05:56 PM ----------
rag1299 said:
Can I flash this kernel in stock CM11 which was shipped along with Yureka?
Click to expand...
Click to collapse
I didn't install in custom ROM yet.. I'm on stock CM11. Can you guide me how to install this kernel?
rag1299 said:
Can I flash this kernel in stock CM11 which was shipped along with Yureka?
---------- Post added at 06:00 PM ---------- Previous post was at 05:56 PM ----------
I didn't install in custom ROM yet.. I'm on stock CM11. Can you guide me how to install this kernel?
Click to expand...
Click to collapse
Follow the tutorial here to get bootloader unlocked and recovery installed.
Once recovery is got, you could follow the instructions on OP page and install the kernel. From the previous posts, i suppose it works fine on the stock CM11 shipped with device.
Hey bro i wanted to know something in eco performnce mode there is an additional 2 written what that means?? Only 2 cores will work at full load or 2 cores will work in light load.. I m very confused regarding this...
---------- Post added at 02:31 AM ---------- Previous post was at 02:29 AM ----------
Sudeep Duhoon said:
Use faux kernel enhancement app.
Go to cpu hotplug
Enable intelli_plug
Set to eco performance.
Click to expand...
Click to collapse
Brother . what does that 2 means here ..
Bcoz i saw that only2 cores worked after sleecting and other cores were genrally oflline even when i played asphalt or mc5 ..
Thanks ... From where to download faux kernel. Can u pls provide the link?
Sent from my AO5510 using xda premium
prateekkej said:
Hey bro i wanted to know something in eco performnce mode there is an additional 2 written what that means?? Only 2 cores will work at full load or 2 cores will work in light load.. I m very confused regarding this...
---------- Post added at 02:31 AM ---------- Previous post was at 02:29 AM ----------
Brother . what does that 2 means here ..
Bcoz i saw that only2 cores worked after sleecting and other cores were genrally oflline even when i played asphalt or mc5 ..
Click to expand...
Click to collapse
same query for me too bro.
raman_ said:
Thanks ... From where to download faux kernel. Can u pls provide the link?
Sent from my AO5510 using xda premium
Click to expand...
Click to collapse
This kernel has implemented faux kernel features and built with latest commits from our device kernel branch. Download link is in OP.
How to enable intelli plug and from where to download faux kernel enhancement app please give links and help!

[KERNEL][UBER 6.0][27/12] Custom Kernel v2.5 for Samsung Galaxy J7

This is a custom kernel for Samsung galaxy J7(Exynos variants of J7)
Use Kernel Aduitor app from Play Store to change kernel parameters.
Changelogs
v2.5
Compiled with UBERTC GCC 6.0
Update to Linux 3.10.94
Remove EXYNOS_STAT_LOG ,Wifi debug ,Android logger and PROFILING
Kernel Quick Wakeup feature(for better battery)
Governors(Hyper,preservative,conservativex,alucard,darkness,nightmare,wheatley,smartassV2,Ondemandplus,dancedance,bioshock,lionheart)
Sio I/O Scheduler
Fix installtion of Busybox
Nvidia power efficiency patches
Optimize LowMemoryKiller driver(kernel side)
Use Powersuspend driver for decon
Frandom
Dynamic Sync control(Faux123)
Many other changes(see github repository)
V2.1
Fixed battery drain in V2(hopefully)
Updated UBERTC 5.2.1 toolchain
V2.0
Compiled with UBERTC GCC 5.2
Update to latest Linux 3.10.90 from 3.10.61
FLashable zip(flash with TWRP)
Busybox
Remove Knox notification
Add BFQ and FIOPS I/O Scheduler(Change them with app 'Kernel Aduitor' on Play Store)
Remove some debug
Disable SEC_OOM_KILLER
Optimize SLUB memory allocator
Reduce wifi battery drain
Optimize cpu hotpllugging
Optimize Deadline I/O Scheduler
Some other misc. changes(See on github)
V1.0
SELinux set to Permissive mode
Compiled with UBERTC GCC 4.9.4
cortex-a57.cortex-a53 optimizations
Files attached in post!
Instructions
You must be rooted ! How to Root? See here: http://sharvinzlife.blogspot.in/2015/10/samsung-galaxy-j7-sm-j700f-tips-and.html
Copy custom_kernel_v2.5.zip(Do not download, v1,it is outdated)
Flash with TWRP recovery :good:
Sources
https://github.com/sakindia123/android_kernel_samsung_j700F
Reserved post
Knox crap in kernel
after some research, found something to remove knox crap from kernel (which taps in the usage of device to make security logs)
here's the thread, jus look into it once
http://forum.xda-developers.com/showthread.php?t=2599266
:angel:
I believe i have managed to silence knox,will make the next kernel update TWRP installable .
Kernel Updated to v2.0,Flash with TWRP!
sakindia123 said:
Kernel Updated to v2.0,Flash with TWRP!
Click to expand...
Click to collapse
Thanks i like it.
Sent from my SM-J700F using Tapatalk 2
Kernel works great ! Thanks @sakindia123 you're awesome !
i looked at the code source i can't find OC tables .. my device J700H ..................................can you plz poste antutu score... and plz can you work on cm13...
nanoteam said:
i looked at the code source i can't find OC tables .. my device J700H ..................................can you plz poste antutu score... and plz can you work on cm13...
Click to expand...
Click to collapse
Antutu score is 39000 on my J700F.
I also am not able to overclock the device.Layout is very different from Exynos 7420 and Exynos 5433
sakindia123 said:
Antutu score is 39000 on my J700F.
I also am not able to overclock the device.Layout is very different from Exynos 7420 and Exynos 5433
Click to expand...
Click to collapse
so can you work on cm13... i know will get anroid m in the future but i like more cm roms
---------- Post added at 08:50 PM ---------- Previous post was at 08:49 PM ----------
kernel work stable for now ... i need more tweaking on gpu to get more performance.... thanks man
Hi sir. Kernel v2 is good. But i feel faster battery drain in my j700h. May be in nxt update u try to fix it. But over all its very nice and smooth. Thanks
Serious bug found in the custom kernel v2
Initially on stock kernel, when outdoor mode in notification panel was enabled, brightness was set to max for convenient viewing under direct sunlight.
But after flashing the custom kernel v2, as soon as outdoor more is clicked, device reboots. Not just once or twice but every time its clicked. Please fix the issue in the custom kernel v3.
And somebody please upload the stock kernel for the time being. Moreover can somebody please check & reply whether the same issue is in the custom kernel v1. Apart from this, is there way to remove the kernel modified notification appearing in the upper left corner when device gets booted, though it's not a major problem but a bit annoying & eye catchy.
Last but not the least, is there a way to receive regular updates in this rooted J700F. If not then where to manually download the latest updates & flash it via custom recovery.
Looking forward to a positive reply&thanks in advance.
hi i want to ask the kernel source in title say .is for J700F with qualcom chipset but in arch64 i find just exynos chipset files no qualcom so is this for J700H or the two has exynos
---------- Post added at 07:34 PM ---------- Previous post was at 07:33 PM ----------
darksam96 said:
Serious bug found in the custom kernel v2
Initially on stock kernel, when outdoor mode in notification panel was enabled, brightness was set to max for convenient viewing under direct sunlight.
But after flashing the custom kernel v2, as soon as outdoor more is clicked, device reboots. Not just once or twice but every time its clicked. Please fix the issue in the custom kernel v3.
And somebody please upload the stock kernel for the time being. Moreover can somebody please check & reply whether the same issue is in the custom kernel v1. Apart from this, is there way to remove the kernel modified notification appearing in the upper left corner when device gets booted, though it's not a major problem but a bit annoying & eye catchy.
Last but not the least, is there a way to receive regular updates in this rooted J700F. If not then where to manually download the latest updates & flash it via custom recovery.
Looking forward to a positive reply&thanks in advance.
Click to expand...
Click to collapse
yep me two...
Could this kernel work in J700M? Someone test it in this model?
This kernel works on exynos models of j7 ( this includes j700h/f models)
messi2050 said:
This kernel works on exynos models of j7 ( this includes j700h/f models)
Click to expand...
Click to collapse
Ok but excuse me for my noob question sir. Samsung J700M do not have exynos Microprocessor? And which Microprocessor use? Thanks in advance
cachok9999 said:
Ok but excuse me for my noob question sir. Samsung J700M do not have exynos Microprocessor? And which Microprocessor use? Thanks in advance
Click to expand...
Click to collapse
It will not work on J700M!Dont try
sakindia123 said:
It will not work on J700M!Dont try
Click to expand...
Click to collapse
Thanks you @sakindia123 for your useful information
Hi guys I check my information again and I have noticed that my Chipset is Samsung Exynos 7 Octa 7580
So, could I use this kernel? Thanks.
cachok9999 said:
Hi guys I check my information again and I have noticed that my Chipset is Samsung Exynos 7 Octa 7580
So, could I use this kernel? Thanks.
Click to expand...
Click to collapse
yes

[KERNEL][CM11][STOCK][4.4.4][4.1.2]kernel-3.5.7-UNOFFICIAL-delos3geur

Links:
DOWNLOAD​
CM11 :-
new
over clocked :=
kernel-20161001-3.5.7-UNOFFICIAL-delos3geur​
non over clocked =
kernel-20161001-3.5.7-UNOFFICIAL-delos3geur-non_oc​
old
new
over clocked :=
kernel-20160930-3.5.7-UNOFFICIAL-delos3geur-oc​
non over clocked =
kernel-20160930-3.5.7-UNOFFICIAL-delos3geur-non_oc​
---------------------------------------------------------------------------------------------------------------------------------------------------------------
kernel-20160927-3.5.7-UNOFFICIAL-delos3geur​
kernel-20160925-3.5.7-UNOFFICIAL-delos3geur​
kernel-20160922-3.5.7-UNOFFICIAL-delos3geur​
kernel-20160920-3.5.7-UNOFFICIAL-delos3geur​
kernel-20160917-3.4.112-UNOFFICIAL-delos3geur​
kernel-20160916-3.4.82-UNOFFICIAL-delos3geur​
kernel-20160915-3.4.0-UNOFFICIAL-delos3geur​
kernel-20160914-3.4.0-UNOFFICIAL-delos3geur​
​
​
STOCK : -
new
kernel-20160923-3.5.7-STOCK-UNOFFICIAL-delos3geur​
old
kernel-20160717-3.4.0-UNOFFICIAL-delos3geur​​
​
Installation Method:
1. Copy downloaded zip file into sdcard
2. Reboot into twrp recovery
3. Install zip file (and wipe data if you are in cm11 and flashed first time)
4. Reboot and done
Features for cm11:
Over Clock GPU to 800 MHZ
added 17 Governors
enabled selinux
removed fmem
updated audio drivers
upgraded version to 3.5.7
added support for 4.9 Gcc
compiled with 5.2 linero gcc
fix some perfomance issue
Added fast charge you need to enable it using perfomance control app
There are lots of changes i can't write all of them you can check commits on github
Fixed some issues while changing governor
Features for stock:
Over Clock GPU to 800 MHZ
added more Governors
Thanks to :=
@weritos
@mahir kukreja
XDA:DevDB Information
[KERNEL][CM11][STOCK][4.4.4][4.1.2]kernel-3.4.0-UNOFFICIAL-delos3geur, Kernel for the Samsung Galaxy Grand Quattro
Source Code: https://github.com/I8552-cm11/android_kernel_arubaslim/tree/delos
Kernel Special Features:
Version Information
Status: Stable
Current Stable Version: 16
Stable Release Date: 2016-07-17
Created 2016-07-17
Last Updated 2016-09-14
this kernel is very good. no bugs are found. thank you android lover
very happy now
flash this kernel on cosmic rom version 1 .It worked perfectly
supports fast charge I think u should put it on feature list (it shows fast charge on performance control app) n thanx for very nice and stable kernal wid such oc thumsup
Great work bro
kernal work like charm
hi I just found one bug when charging my mobile it restarts(randomely 1 tym ) and is gaining morethan 50% charge its been some tym now im using stock de odexed wid xposed , xblast tools and im not using fast charge .dont know how to make a logcat so if some one else is experiencing the same problem pls comment
it is sloved thnx
can i install it with cwm ?
nqhoai said:
can i install it with cwm ?
Click to expand...
Click to collapse
bro use twrp recovery by android lover .it is also very good .
to flash twrp recovery over cwm use this method:
http://forum.xda-developers.com/gra...talling-twrp-3-0-2-androidlover-odin-t3420406
hit thanks if it helped you
qualcomm chipset nice
Good one bro
Help needed
givig me error on when i install on cosmic rom as the basis problem is cosmic rom is ported so in setting it displays the model no. of galaxy core so when i flash the kernel error comes that unable to flash coz of different model but with gluon kernel i dont get error in flash so how to flash this kernel on cosmic rom ?
hi
tejus said:
givig me error on when i install on cosmic rom as the basis problem is cosmic rom is ported so in setting it displays the model no. of galaxy core so when i flash the kernel error comes that unable to flash coz of different model but with gluon kernel i dont get error in flash so how to flash this kernel on cosmic rom ?
Click to expand...
Click to collapse
hello tejus
flash the kernel over cosmic rom version 1
no problem will arise at all:good:
it works perfectly
even i am using the same cosmic version 1 and this kernel
hit thanks if it was helpfull
arjuntsgowda said:
hello tejus
flash the kernel over cosmic rom version 1
no problem will arise at all:good:
it works perfectly
even i am using the same cosmic version 1 and this kernel
hit thanks if it was helpfull
Click to expand...
Click to collapse
okay i ll try
well done thank!
Is it a swap-compatible kernel?
Couple of days back, I tried to expand RAM with ROEHSOFT RAM Expander. But got this message "this device has not swap compatible kernel"
Not supported
zooperaj said:
Is it a swap-compatible kernel?
Couple of days back, I tried to expand RAM with ROEHSOFT RAM Expander. But got this message "this device has not swap compatible kernel"
Click to expand...
Click to collapse
If u need swap enabled kerenl to use ROEHSOFT Ram expander use this http://forum.xda-developers.com/gra.../kernel-swap-enabled-kernel-gt-i8552-t2936912
and basically the kernel in this thread is for performance so i prefer u to use this kernel coz this kernel is better that swap enabled kernel :laugh::good:
Hi Tejus,
I tried the kernel referred by you. According to what I understand from its installation instructions, I flashed both the zips (swap file zip and restore file zip). But my phone's wi-fi was disabled. So, I had to restore my mobile to its previous state through CWM. Please guide.
---------- Post added at 04:15 PM ---------- Previous post was at 04:14 PM ----------
tejus said:
If u need swap enabled kerenl to use ROEHSOFT Ram expander use this http://forum.xda-developers.com/gra.../kernel-swap-enabled-kernel-gt-i8552-t2936912
and basically the kernel in this thread is for performance so i prefer u to use this kernel coz this kernel is better that swap enabled kernel :laugh::good:
Click to expand...
Click to collapse
Hi Tejus,
I tried the kernel referred by you. According to what I understand from its installation instructions, I flashed both the zips (swap file zip and restore file zip). But my phone's wi-fi was disabled. So, I had to restore my mobile to its previous state through CWM. Please guide.
---------- Post added at 04:22 PM ---------- Previous post was at 04:15 PM ----------
zooperaj said:
Hi Tejus,
I tried the kernel referred by you. According to what I understand from its installation instructions, I flashed both the zips (swap file zip and restore file zip). But my phone's wi-fi was disabled. So, I had to restore my mobile to its previous state through CWM. Please guide.
---------- Post added at 04:15 PM ---------- Previous post was at 04:14 PM ----------
Hi Tejus,
I tried the kernel referred by you. According to what I understand from its installation instructions, I flashed both the zips (swap file zip and restore file zip). But my phone's wi-fi was disabled. So, I had to restore my mobile to its previous state through CWM. Please guide.
Click to expand...
Click to collapse
Hi Tejus again,
What will kernel in this thread exactly do? Please guide. Please excuse me if I am bothering you a lot. Last week, I rooted my phone and since then have been looking for some tweaks, ROMs etc. But due to limitations put by original kernel (please correct me if I am wrong) it seems nothing satisfactory is happening. So, it is making me nervous Also, I am not able to move apps to external sd card. It is so disappointing.
u only need to flash one zip
zooperaj said:
Hi Tejus,
I tried the kernel referred by you. According to what I understand from its installation instructions, I flashed both the zips (swap file zip and restore file zip). But my phone's wi-fi was disabled. So, I had to restore my mobile to its previous state through CWM. Please guide.
---------- Post added at 04:15 PM ---------- Previous post was at 04:14 PM ----------
Hi Tejus,
I tried the kernel referred by you. According to what I understand from its installation instructions, I flashed both the zips (swap file zip and restore file zip). But my phone's wi-fi was disabled. So, I had to restore my mobile to its previous state through CWM. Please guide.
---------- Post added at 04:22 PM ---------- Previous post was at 04:15 PM ----------
Hi Tejus again,
What will kernel in this thread exactly do? Please guide. Please excuse me if I am bothering you a lot. Last week, I rooted my phone and since then have been looking for some tweaks, ROMs etc. But due to limitations put by original kernel (please correct me if I am wrong) it seems nothing satisfactory is happening. So, it is making me nervous Also, I am not able to move apps to external sd card. It is so disappointing.
Click to expand...
Click to collapse
just download swap v3 kernel and flash dont need to flash the 'restore module file'
androidlover5842 said:
Links:
DOWNLOAD​
CM11 :- kernel-20160914-3.4.0-UNOFFICIAL-delos3geur​
STOCK : - kernel-20160717-3.4.0-UNOFFICIAL-delos3geur​
Installation Method:
1. Copy downloaded zip file into sdcard
2. Reboot into twrp recovery
3. Install zip file
4. Reboot and done
Features for cm11:
Over Clock GPU to 800 MHZ
added 16 Governors
enabled selinux
Fixed some issues while changing governor
Features for stock:
Over Clock GPU to 800 MHZ
added more Governors
Thanks to :=
@weritos
@mahir kukreja
XDA:DevDB Information
[KERNEL][CM11][STOCK][4.1.2]kernel-3.4.0-UNOFFICIAL-delos3geur, Kernel for the Samsung Galaxy Grand Quattro
Source Code: https://github.com/I8552-cm11/android_kernel_arubaslim/tree/delos
Kernel Special Features:
Version Information
Status: Stable
Current Stable Version: 2
Stable Release Date: 2016-07-17
Created 2016-07-17
Last Updated 2016-09-14
Click to expand...
Click to collapse
Planning to add SWAP?I really want swap with ur GPU overclock
---------- Post added at 07:35 AM ---------- Previous post was at 07:26 AM ----------
BTW I wanna install this but I pressed YEs when i'm in cwm askinhlg ROM may install stock recovery
I'm using Gluon Kernel preinstalled by Metemod ROM v1 (cm11-themed)
---------- Post added at 07:36 AM ---------- Previous post was at 07:35 AM ----------
Is it still possible to install this rom
?
Once again awesome work bro @androidlover5842
Gonna flash CM11 kernel and give feedback soon ?
androidlover5842 said:
Links:
DOWNLOAD​
CM11 :- kernel-20160914-3.4.0-UNOFFICIAL-delos3geur​
STOCK : - kernel-20160717-3.4.0-UNOFFICIAL-delos3geur​
Installation Method:
1. Copy downloaded zip file into sdcard
2. Reboot into twrp recovery
3. Install zip file
4. Reboot and done
Features for cm11:
Over Clock GPU to 800 MHZ
added 16 Governors
enabled selinux
Fixed some issues while changing governor
Features for stock:
Over Clock GPU to 800 MHZ
added more Governors
Thanks to :=
@weritos
@mahir kukreja
XDA:DevDB Information
[KERNEL][CM11][STOCK][4.4.4][4.1.2]kernel-3.4.0-UNOFFICIAL-delos3geur, Kernel for the Samsung Galaxy Grand Quattro
Source Code: https://github.com/I8552-cm11/android_kernel_arubaslim/tree/delos
Kernel Special Features:
Version Information
Status: Stable
Current Stable Version: 2
Stable Release Date: 2016-07-17
Created 2016-07-17
Last Updated 2016-09-14
Click to expand...
Click to collapse
You are the best , I hope that this kernel will further improve the performance of cm11:good:

[KERNEL][MM][DRM FIX] EliteKernel v3.4.33 [UB]

Elite Kernel
Unleash the beast
for Xperia Z3/Z3 Dual (need test)
First of all, I have spent a lot of hours on this project, trying to obtain the true power of this great device.
This Kernel is designed for optimize battery life and give more performance than stock kernel.
Features
Based on lastest sources, 23.5.A.1.291
DRM injection inside the Zip, you don't need flash DRM Fix, just kernel
OC up to 2,7Ghz
UC for better battery life
Optimized voltage tables and voltage control
Thunderplug v5.4, a load based hotplug and optimized for multi-core devices and it is very battery friendly with a great performance
IntelliThermal v2, a custom thermal control better than stock one
GPU overclock up to 657Mhz
Kcal control
More I/O schedulers like FIOPS, Zen, VR, BFQ...
init.d support
Power suspend driver v1.5
Build with UBERTC 4.9 and some optimizations
More stuff that I don't remember
ToDo
Add more governors
Share interactive governor tuned settings for battery and performance
More GPU optimizations
F2FS support
More battery life optimizations
Maybe Quick Chargue 2.0 support.
Maybe sound optimizations
Installation
Install my lastest TWRP (go here)
Make a backup of the partition System (MUST DO, because the kernel change some modules on system)
Select a version according to your needs. (See below)
If you have a TA partition backup:
Download EliteKernelZ3-(current version).zip and extract the boot.img on your pc.
Use the ta_poc tool by munjeni with your TA partition backup.
Rename the new_boot.img to boot.img and replace it on the EliteKernelZ3-(current version).zip
Boot on FOTAKernel recovery, with the phone power off, press at the same time power key and vol- until the phone vibrates.
Flash your EliteKernelZ3-(current version).zip with the boot.img patched.
Enjoy!
Click to expand...
Click to collapse
If you don't have a TA partition backup (so you need DRM FIX):
Boot on FOTAKernel recovery, with the phone power off, press at the same time power key and vol- until the phone vibrates.
Flash EliteKernelZ3_D-(current version).zip
Enjoy!
Click to expand...
Click to collapse
Usage with eXistenZ 5.6.5 (or similar Stock based ROMs) and Magisk
eXistenZ 5.6.5 includes a TWRP recovery inside the rom, and we don't need it since we have some options for recovery here, so for remove it download this file and flash it on recovery.
eXistenZ 5.6.5 also includes SuperSU on the rom and for correclty install magisk we need to remove it, so first of all update the SuperSU app on the Play Store, after go to the app and on settings there is an option for uninstall SuperSU and unroot the System, so tap it (Sometimes if it takes more of 3 mins, close the app and do it again), after that reboot the phone and done, SuperSU uninstalled.
Now the installation/upgrade of magisk using my kernel.
Download the lastest magisk zip and magisk uninstaller zip here, put they on SD card.
Reboot on recovery, uninstall magisk with the uninstaller zip if you have it, flash the kernel zip, flash magisk and reboot to system, and done, enjoy magisk.
Download
Z3
Z3ds
Credits
@AndroPlus
@Myself5
@DooMLoRD
@pec0ra
@dorimanx
@faux123
@Doom Slayer a lot of thanks to this great dev
@dontbelive great dev and my Z3 tester
@BlackSoulxxx
@savoca
Source
https://github.com/ShadowElite117/Xperia-Z2-Z3
Changelog
v1
First release
Click to expand...
Click to collapse
v2
Based on new 23.5.A.1.291 sources
Click to expand...
Click to collapse
v3
Added missing conservative GPU Governor
Added Simple GPU algorithm
Added Adreno idler for battery saving
Added Fauxsound v3.6
More optimizations
Click to expand...
Click to collapse
v3.4.13
Kernel made from scratch, so no special features for now (Sorry guys I do this for a better kernel).
Implemented last_kmsg for a correct bug report.
Updated linux kernel version from 3.4.0 to 3.4.13 (Correclty done and free of strange bugs).
QC 2.0 enabled (don't expect miracles, it is limited on Z3 so it works with some QC 2.0 chargers)
Full compatibility with Magisk, eXistenZ and ta_poc tool.
Click to expand...
Click to collapse
v3.4.33
Updated linux kernel version from 3.4.13 to 3.4.33.
Enabled a kernel flag for try to enable Assertive Display on Z2 (It just give me logs that help me to know what is happening).
Dropped TWRP inside the kernel, since I have build newest TWRP for leo, for FOTAKernel partition. It has more features and it is more bug free than recovery inside the kernel.
Click to expand...
Click to collapse
FAQs
Q. How I can report a bug?
A. Give me a last_kmsg, tell me your ROM, if you have Magisk, Xposed Framework or similar things and describe me the problem.
Q. How I can contact you?
A. Please don't spam me with PMs, you can contact me on Telegram: ShadowElite117
Thanks!! @ShadowElite I'm happy to see another custom kernel with some special features like AndroPlus ones for the MM version!
BTW can you make for 23.5.A.1.203 or other version(with stamina)?
Because i don't know whether this .575 kernel compatible with Stamina mode...
Glad to see another custom kernel for our Z3. It would also be amazing if you could update to. 238
Thanks!
Be patient guys, sony will release the sources of 238 soon
Looks promising, and thank you for thinking about dual sim users !
I'm eagerly waiting for d6633/83 version. Is there a way to choose GPU overclock/underclock ?
tiliarou said:
Looks promising, and thank you for thinking about dual sim users !
I'm eagerly waiting for d6633/83 version. Is there a way to choose GPU overclock/underclock ?
Click to expand...
Click to collapse
Z3 Dual version is build but I uploaded the wrong file so later I'm going to upload it and yes GPU has OC/UC and you can modify it with a kernel app like kernel adiutor or ex kernel
whoa... custom kernel for Z3 at last! great news
I'd like to test it, but I'll have to wait for .238 support
Finally!!! Custom kernel with Undervolting this is what I'm seeks ????
oh my god this is a miracle is real kernel more control over what can not believe thanks thank you very much for your contribution
I`m so happy about z3 mm custom kernel!
thx to make this kernel!
this needs unlocked bootloader ?
Wooooop finally a kernel for MM, thank you p.s thanks so much for f2fs aswell
Sent from my D6603 using XDA-Developers mobile app
lorvix said:
this needs unlocked bootloader ?
Click to expand...
Click to collapse
Of course it does. It's a custom kernel.
@ShadowElite Do i have to be on 575 base to use your kernel? And good timing i just bought my Z3 and was dissappointent that there were no custom kernels,thanks. Also can we ask for changes or features on your kernel?
Does this kernel have kexec hardboot, or is there plans for implementing it?
zhjackss said:
@ShadowElite Do i have to be on 575 base to use your kernel? And good timing i just bought my Z3 and was dissappointent that there were no custom kernels,thanks. Also can we ask for changes or features on your kernel?
Click to expand...
Click to collapse
You can have 570 575 203 238 firmware and this kernel will work, when Sony release the source of 238 I update it. Also you can see the most important features on first post and you can ask for features
Discordian_Nerd said:
Does this kernel have kexec hardboot, or is there plans for implementing it?
Click to expand...
Click to collapse
Yeah I have planned add support, I forget it on ToDo list
it is necessary to do a clean installation or can I keep my app?
There will be for Xperia Z3 compact?

[KERNEL]|TW][MM][LINARO]Khaon's kernel for the A3(2016) 22/12

disclaimer said:
I am not responsible for any damage to your phone.
Read before downloading or posting in the thread:
Proceed with caution if you have no experience.
Click to expand...
Click to collapse
FOR TOUCHWIZZ USERS ONLY​
INTRODUCTION
Hello, I like doing not too heavy custom kernel, that's why I am sharing with you the kernel, hopefully at least someone like it! I have two version of this one. But some instabilities seems to be related with the hundred of patches I added from the stable linux kernel patches project and from the common Google android kernel repo.
This is an open devDB xda project. Feel free to fill in bugs reports, feature(s) requests and reviews.
My kernel is not intended to come along with tons of patches like many kernel you can see around..
However, I think it has some nice extras features I'ill try to increase in the coming weeks.​Kernel's features :​
Latest Samsung's sources for MM
Compiled with GCC linaro64 6.2
Compilation options: O3 and architecture options enabled(A53 code generation optimized)
Double tap to wake: Removed for now because of non responsive screen.
cpufreq:touchboost duration and touchboost freq tweakables(only for interactive gov)
Second CPU clusters enabled: you will get 8 cores.
Overclocked max frequency for the first CPU clusters to 1.6Ghz ( 1.5 ghz remains the default)
Underclocked the second CPU cluster to 1.4 GHz not to have overheat problems
Voltage control for the first CPU
Tweaked cfq i/o scheduler to be more logical as we use NAND and not an HDD
​installation instructions :​
You need TWRP recovery to start with: @ashyx custom recovery does every well ! I recommend this one
Once you get TWRP installed:
If your are scared to flashing something that will ruin your boot image; you can backup your current boot image from the BACKUP menu
copy to your phone the boot.img I provided.
Press INSTALL then press the right bottom button 'install Image' to switch to theflash image feature, then navigate to the path your copied the boot.img.
Select it and just flash !
Now you can reboot .
What does work !
You can not set a max_freq for the second cluster: this is due because each time it goes on and let you the hability to change it, it will go offline and everything is to start again(if you dont crash until then). I think there is some easy for fix but I need to look over it.
What I would like to implement:
CPU voltage control
GPU governor down and threshold for each frequency step
GPU touch boost
DOWNLOADS LINK​
XDA:DevDB Information
Khaon personal kernel for the A3 (2016) 13/10, Kernel for the Samsung Galaxy A Series
Contributors
Khaon, alexax66
Source Code: https://github.com/Khaon/android_kernel_samsung_a3xelte
Kernel Special Features: COmpiled by linaro 6.1, dt2w, blx, internal kernel space touchboost, SoC second cluster enabled(4 extra cores)
Version Information
Status: Stable
Stable Release Date: 2016-10-13
Created 2016-09-11
Last Updated 2016-12-31
Sorry, only ServiceLogin.htm is able to download. Please correct link
---------- Post added at 01:51 PM ---------- Previous post was at 12:57 PM ----------
Download now works, thanks. Kernel works fantastic. Thanks
if allowed, let me link a flashable odin file
Can You compile one for A510F?
IvoDi said:
Can You compile one for A510F?
Click to expand...
Click to collapse
I am afraid I won't do this, as I don't own the device to test.
Jerome-X said:
if allowed, let me link a flashable odin file
Click to expand...
Click to collapse
I think flashing with ODIN is a waste of time against the solution I provide.
Furthermore I am on linux. So no Odin.
Khaon said:
double tap to wake...
Click to expand...
Click to collapse
Can you tell us, how to do this?
Tapped by SM-A310F
Some Geekbench scores here? I got Single: 626 and Multi: 2631
Ok thank you, i want to try your kernel. But if i want to restore the original? How can i do?
I suppose that if i make a backup of the boot.img, then in future i can restore this one. Is ok?
Thank you
---------- Post added at 02:23 PM ---------- Previous post was at 02:07 PM ----------
MarcoFal said:
Ok thank you, i want to try your kernel. But if i want to restore the original? How can i do?
I suppose that if i make a backup of the boot.img, then in future i can restore this one. Is ok?
Thank you
Click to expand...
Click to collapse
OK ... i've done the backup, installed the img of your boot and then ... the phone don't boot ...
I't show online the Samsung Galaxy Logo at the start, in the upper part of the monitor the red write abouth the kernel and then black ....
What can i do now?
... i'm not able to enter in TWRP ... i try all the button combo, what is the correct button combination?
Thank you ...
---------- Post added at 02:59 PM ---------- Previous post was at 02:23 PM ----------
I've found how to enter in recovery and restore boot image ... the phone now works ... Well
What was my error in flashing your boot image?
I've got an A310F, build version A310FXXU2APDC, Android 5.1.1.
I'had upload you image with TWRP 3.0.2, after have choosen to install an image, not a zip.
The procedure tell me that everything was ok ...
Thanks
Does the CPU really has originally 8 cores? Is there any plausible reason why Samsung kept only 4 of them working by default?
thx :good:
Hey there,
Can i use this kernel if i use the Nova Launcher instead of touchwiz?
I ask because in the First Post the Dev said "for touchwiz User only".
Thanks.
JebusHerrl said:
Hey there,
Can i use this kernel if i use the Nova Launcher instead of touchwiz?
I ask because in the First Post the Dev said "for touchwiz User only".
Thanks.
Click to expand...
Click to collapse
yes
Someone was able to install this kernel and to use it?
I 've tried to install but the phone don't boot ... Any help?
MarcoFal said:
Someone was able to install this kernel and to use it?
I 've tried to install but the phone don't boot ... Any help?
Click to expand...
Click to collapse
yes its working fine till now
mr.b4rt said:
yes its working fine till now
Click to expand...
Click to collapse
What was my error in flashing the boot image?
I've got an A310F, build version A310FXXU2APDC, Android 5.1.1.
I'had upload the image file with TWRP 3.0.2, after have choosen to install an image, not a zip.
The log tell me that everything was ok ... but when i reboot the phone tell me that 'the kernel is not seanfored' and then doesn't boot and stay black.
I can only restore my backup boot image ...
Is there something that i have to check or do?
Inviato dal mio SM-A310F utilizzando Tapatalk
MarcoFal said:
What was my error in flashing the boot image?
I've got an A310F, build version A310FXXU2APDC, Android 5.1.1.
I'had upload the image file with TWRP 3.0.2, after have choosen to install an image, not a zip.
The log tell me that everything was ok ... but when i reboot the phone tell me that 'the kernel is not seanfored' and then doesn't boot and stay black.
I can only restore my backup boot image ...
Is there something that i have to check or do?
Inviato dal mio SM-A310F utilizzando Tapatalk
Click to expand...
Click to collapse
kernel is for mm not lp
I have A510F MM and i install this kernel my device is bootloop. I bring back twrp recovery my files. But i need custom kernel for my devices. Anyone create kernel for A510F?
installed and booted successfully .dt2w does not works properly and phone hangs when i change frequency and got 3-4 restart in half an hour..but it looks promising keep up the good work..
8core rocks with MM
Yeah!

Categories

Resources