Revive my dead china clone with RK3188 (rockchip-rk31sdk)_ Please Help - Android Q&A, Help & Troubleshooting

I'm badly need some expert advise.
.My china clone without name (rockchip-rk31sdk-WAWJMDN1KN).I decide to go ahead and try some custom rom using RKAndroidTool.
I did not realize that by cleaning IDB I will low level format..Before doing that I did save few pictures and run log via "android studio" also I backup whole unit via CWM hoping I will always have access to recovery.Unfortunately that not the case.The good think I still have access to RKAndroidTool( the tool is recognizing my device).There is the link to my CWM backup if may help
https://mega.nz/#!g8YgVKaa!209scxKfT...lRZ454peCCCsgU
https://mega.nz/#!gwRGhC7B!KFvTGpp4x...M2AHOKjT43VPQI
Inside that CWM backup is kernel.bin, system.bin recovery bin all
large sizes files (complete CWM of my last working tablet rk3188). Please ask me for pass to open 2x rar.
Maybe You will be able to advice me how to make proper files to revive my system from that backup I have, or help me some how to get CWM recovery working so I can use my CWM backup or any other way to make this tab back to life again.
Perhaps someone will give me idea to allocate proper parameter for recovery , kernel , boot , etc...
Usual location for tablet RK3188 Cortex A9 Quad core 1.6 ghz Governor interactive, Kernel 3.0.36+ ,Board hardware RK30Board/ 0000, Android 4.2.2 ;eng.root 20130912.185132 sdk 17, Display 1280x800; dpi;160 size 9.4'
GPU:Mali-400MP, RAM: 2048 Flash:32 gb Build in:16gb actual, wifi, usb, Bluetooth gps= all yes, camer 5MP additional 1.9MP.
Many thanks for your kindness and time.
Adam

styropian said:
I'm badly need some expert advise.
.My china clone without name (rockchip-rk31sdk-WAWJMDN1KN).I decide to go ahead and try some custom rom using RKAndroidTool.
I did not realize that by cleaning IDB I will low level format..Before doing that I did save few pictures and run log via "android studio" also I backup whole unit via CWM hoping I will always have access to recovery.Unfortunately that not the case.The good think I still have access to RKAndroidTool( the tool is recognizing my device).There is the link to my CWM backup if may help
https://mega.nz/#!g8YgVKaa!209scxKfT...lRZ454peCCCsgU
https://mega.nz/#!gwRGhC7B!KFvTGpp4x...M2AHOKjT43VPQI
Inside that CWM backup is kernel.bin, system.bin recovery bin all
large sizes files (complete CWM of my last working tablet rk3188). Please ask me for pass to open 2x rar.
Maybe You will be able to advice me how to make proper files to revive my system from that backup I have, or help me some how to get CWM recovery working so I can use my CWM backup or any other way to make this tab back to life again.
Perhaps someone will give me idea to allocate proper parameter for recovery , kernel , boot , etc...
Usual location for tablet RK3188 Cortex A9 Quad core 1.6 ghz Governor interactive, Kernel 3.0.36+ ,Board hardware RK30Board/ 0000, Android 4.2.2 ;eng.root 20130912.185132 sdk 17, Display 1280x800; dpi;160 size 9.4'
GPU:Mali-400MP, RAM: 2048 Flash:32 gb Build in:16gb actual, wifi, usb, Bluetooth gps= all yes, camer 5MP additional 1.9MP.
Many thanks for your kindness and time.
Adam
Click to expand...
Click to collapse
UPDATE____
RK3188 adb is running no screen__help PLEASE
After erasing IDB in my unknown china tablet and loosing my whole system I was able to load different custom firmware from Chuwi v88 + different kernel and my Tab popup in windows showing 2 extra drives F and G.I did open android studio and notice access to adb and all activity in my android.The RKandroidTool also recognizing my tab.
No reaction to power button only automatically connecting to my comp ( black screen on my tab).
I have original CWM backup of my device.
Can someone advise me how to access recovery from this point or find the way to completely start my tablet.Maybe is possible to recover CWM from adb?I will need some help to use a proper commands perhaps in adb.

Related

[Q] Can anyone help me root a dapeng a7 mtk6573

I have a Dapeng A7 mtk6573 Android phone I just purchased. It was supposed to come prerooted but for some reason it did not and the ebay seller wont take it back or exchange it with another one that is rooted like the original item description said he would. So Im not sure where to go from here. I tried Superoneclick and didnt get very far with it. I am still new to the whole rooting process but i managed to root and rom my Evo 4g without bricking it multiple times. I can follow any directions given just need some help to be pointed in the right direction on how to get this one rooted. Can anyone help?
hi, sorry fo my english
you must download a russian modded recovery here: ge.tt/5UwovRF/v/02
you must flash it with flash tool,...(see many guide in internet if you no know)
after you must enter in it, you pull power and vol+ together,
and install this file: ge.tt/1ili71F/v/0
after you had disabled verification of signature.
so reboot your phone
Angelo
ps
i.m newbee and no can post link.. added http//
shad0w1369 said:
I have a Dapeng A7 mtk6573 Android phone I just purchased. It was supposed to come prerooted but for some reason it did not and the ebay seller wont take it back or exchange it with another one that is rooted like the original item description said he would. So Im not sure where to go from here. I tried Superoneclick and didnt get very far with it. I am still new to the whole rooting process but i managed to root and rom my Evo 4g without bricking it multiple times. I can follow any directions given just need some help to be pointed in the right direction on how to get this one rooted. Can anyone help?
Click to expand...
Click to collapse
As soon as I have some spare time I'll try to follow this
http://ciphone.fr/blog/blog1.php/rooter-son-gsm-chinois-android
But the SuperOneClick download is detected as virus, so I have downloaded it from xda-developers
Bye
merlot said:
As soon as I have some spare time I'll try to follow this
...
But the SuperOneClick download is detected as virus, so I have downloaded it from xda-developers
Bye
Click to expand...
Click to collapse
SuperOneClick does not work on my Dapeng A7. Instead I use adb remount, then adb push superuser.apk into /system/app. This works.
Please note that adb remount does not always work. I have to try a few times. Most of the time, I got success by turning USB debugging on only after I connected the phone and umount USB drive.
Dapeng A7 1gb rom custom recovery
I have good news for 1gb Dapeng A7device owner (aka e1108_v73_hjy2a7) who wants to root/backup their phone.
I just finished modding a custom recovery based on 512mb recovery by replacing original boot.img with 1gb boot.img and tested to work fine (credit to linerty for the base of 592zn.com recovery image file)
To use this, please make sure you have 1gb rom via engineer mode by typing *#*#3646633#*#* on dialpad and choose Memory > Nand Flash ... if it states
Name : KBY00U00VA_B4, ID: 0xecb3, total size 1024mb
Click to expand...
Click to collapse
then this recovery is for you.
Using 512mb recovery on 1gb device will show below error due to missing partition when boot into recovery:
E:can't mount CACHE:recovery/command
E:can't find MISC:
E:can't mount CACHE:recovery/log
E:can't open CACHE:recovery/log
E:can't find MISC:
Click to expand...
Click to collapse
here is Dapeng A7 1gb custom recovery:
http://www.4shared.com/archive/83g2LqtZ/dapeng_a7_1g_rec.html
Dapeng A7 1gb scatter file: http://www.4shared.com/office/XWtNUNVL/MT6573_Android_scatter_dapeng_.html
make sure you download both files
Use SP flash tool, load the scatter file, make sure you only tick recovery and choose the img file ... remove battery and usb cable, press download on SP flash tool ... insert battery .. then insert usb cable (you have 15 sec to do this) ... once it finish, remove and reinsert battery, hold Vol up + power to boot into recovery
-------- after booting into the custom recovery -----------
Now you can flash the uniroot2.signed.zip to root it (get it here) or make nandroid backup, flash custom zip etc. (to flash custom zip - eg: custom rom, make sure toggle signature verification to disable 1st)
512mb device (e1108_v73_hjy1) please use the custom recovery as stated here.
Note : It is advisable to make a full factory backup using mobileuncle gscript after rooting your device as stated here : http://forum.xda-developers.com/showthread.php?p=27039072
Disclaimer: please understand that I'm just trying to help and do not take any responsibilities if you brick your device. (mt6573 devices won't easily brick if you have your backup or the right factory firmware - simply run SP flash tool and overwrite for factory firmware or use recovery mode to restore backup)
ps : recovery mode is good until you mistakenly flash preloader/dsp_bl/uboot img file .. other than these 3 files, the phone should be up and working after restore.
Problems with our two DAPENG A7 and mobiles-phones.cn
Problems with our two DAPENG A7
Hello,
(sorry for my english, it's not my first language)
We bought two Dapeng A7 from mobiles-phones.cn last month. both of them failed within a month !! The first one had video bugs and could not take phtos and videos anymore (cost 26€ to return it back)
The second one has no more microphone and needs an earphone to work !!
A friend of mine just received the DAPENG A75 last week and has a flash LED problem.
So, take care with these Dapeng products wich are not reliable (we had a chinese H7300 wich was very good) at all. Don't hesitate talking about chinese phones troubles on this forum, it could be good for someone hesitating to order over there.
Bye
DAPENG A7 = MT6573
DAPENG A75 = MT6575
Please do not mix between the models. Btw, have you tried restore to factory/factory reset? maybe it's only a software bug.
Dapeng A7 1gb firmware backup
Hi all,
After going through much trouble .. I finally managed to extract Dapeng A7 1gb rom (e1108_v73_hjy2a7) in the form of img files so that others can try revive their bricked Dapeng A7 1gb phone via spflashtool.
Take note that this is only for Dapeng A7 1gb nand/rom ONLY. Please check via dialpad *#*#3646633#*#* and choose Memory > Nand Flash.
http://www.4shared.com/archive/n3y60_1L/backup_dapengA7_e1108_v73_hjy2.html
This is unrooted, untouched firmware. So if you want root, refer to my previous post on how to root using custom recovery and uniroot2signed.zip
Now I don't have the phone anymore. So I wish all the best to those who wants to revive their phone due to wrong flashing/etc.
A7 MTK6573 uboot.img
aze2learn said:
DAPENG A7 = MT6573
DAPENG A75 = MT6575
Please do not mix between the models. Btw, have you tried restore to factory/factory reset? maybe it's only a software bug.
Click to expand...
Click to collapse
I have a A7 MTK6573 Dapeng Android phone I just purchased. The smart phone Adopts A7 Android 2.3 OS and 5.0 inch capacitive multi-touch screen to make the operation smoother and more convenient. It supports WCDMA 3G and GSM network, and supports dual SIM card. Besides, it supports wireless internet, GPS navigation and can be used to watch TV and taking pictures. With complete functions and unique design, it is a good choice for 3G smart phone.
- Operating System: Android 2.3.
- Product Category: 3G smart phone.
-CPU: MTK6573 670Ghz
- RAM: 443.3MB
- ROM: 164.1MB
Network
- Frequency Band: WCDMA / GSM850 / 900/1800 / 1900MHz.
- Network Connection: GPRS, WiFi, WAP.
Display
- Screen Size: 5 inch.
- Screen Resolution: QVGA (480 × 800pixels).
- Touch Screen: Yes, capacitive touch screen.
Storage
- Built-in Memory: 164MB.
- External Memory: MicroSD / TF card up to 32GB.
Camera
- Rear Camera: Yes.
- Pixel: 8 million pixels.
- Flashlight: Yes.
- Front Camera: Yes.
Data Transfer
- GPS Navigation: Yes.
- Wi-Fi: Yes, IEEE802.11b/g/n.
- Bluetooth: Yes.
Amusement Functions
- E-book: Yes, TXT format support.
- FM: Yes.
- Built-in Game: Yes.
- Audio Format: MP3 / M4A / MID / AMR / WAV.
- Video Format: 3GP / MP4 / AVI / MPG / RMVB / WMV.
- Image Format: JPEG / BMP / GIF / PNG.
- SNS Service: Facebook, YouTube, Twitter.
- Chord Ringtone: Polyphonic / MP3 / M4A / MID / AMR / WAV.
Other Functions - Talk Time: Up to 4 hours.
- Standby Time: Up to 200 hours.
- Earphones: Yes, a wired stereo earphones with built-in MIC and clip.
- USB cable: Yes.
- Support Languages: German, Inglés, Spanish, French, Portuguese,-Package Including:
1 * Android smart phone
1 * Wired Stereo Earphones
2 * Rechargeable Li-ion Battery
1 * USB Cable
1 * Power Adapter
1 * User Manual
1 * 8GB micro sd card good phone but try root and the screen image is not stable, it seems that is not the correct uboot.img and now the screen is distorted. if someone could help would greatly appreciate it. Please upload the file uboot.img of this phone ... Thank you.
stovals said:
- Built-in Memory: 164MB.
Click to expand...
Click to collapse
Your device seems to be a 512mb device. Please use the uboot from dump here : http://ge.tt/1qRbflF/v/0?c
angelobiz said:
hi, sorry fo my english
you must download a russian modded recovery here: ge.tt/5UwovRF/v/02
you must flash it with flash tool,...(see many guide in internet if you no know)
after you must enter in it, you pull power and vol+ together,
and install this file: ge.tt/1ili71F/v/0
after you had disabled verification of signature.
so reboot your phone
Angelo
ps
i.m newbee and no can post link.. added http//
Click to expand...
Click to collapse
I confirm this works perfect on my A7 512mb :good:, I did a factory reset before flashing the ROM partially.

[Q] Help with ROM dump on Chinese tablet GT90H Allview A23

Hi all,
I need your help with the following tablet 9" GT90H with Allview A23 CPU/ chipset and android 4.2. I want to backup the ROM, to perform few modifications and to upload the modified image to the tablet, but I am stuck on the first phase (cannot dump the rom).
I tried several ways to do it (actually that I found) to dump/ backup the stock ROM but I was stuck on all of them. First I tried using the clockwork way, but unfortunately my tablet is not supported (and I could not find supported MOD). Then I tried with romdump, but unfortunately I was stuck because the tablet does not have /proc/mnt file. Finally I found a way using the rkdump method but I had non recognize image error (although I am not sure if I found the correct partition to back up - /dev/block/by-name/recovery ). I have doubts if this is the correct partition, because I did a binary copy using dd to a file, which ended up with size around 32 MB (which I found too small for a recovery image).
So that is why I decided to seek help from more advance users (this is my first tablet, and first android experience) and I believe this forum is the right place for that.
My first request is could someone guide how to make a proper ROM backup, that I would be able to restore later?
In addition I want to ask is it possible, once I backed up the ROM, to modify for example the home page (because on the current ROM the home page for all browsers that I install is http://www.baidu.com)?
Moreover I would like to to install the ROM on external memory card and to run the tablet from there (because the internal memory of this table is too low - 8GB but for the system partition I have only 500 mb, which are all occupied with pre installed software). Is this something that I can achieve (android as far as I know is *unix system, and in theory this should be possible)?
Thank you in advance.
For increase space you can use Terminal Emulator for market and must have root on tablet.
Open terminal , and run the commands :
pm get-install-location (this will show you where apps are installing in this moment)
Auto device install is 0 (the tablet chose auto where to install apps,usuale is chosing to internal memory,your 500mb )
internal memory is 1 (Tablet memory - your 500mb )
External memory is 2 this is where you want to instal apps - (your 8GB )
After run the comand and see the sistem is set to AUTO (0) you will run this :
pm set-install-location 2 - This will force apps to instal in your 8gb
to check if is ok , run again : pm-get-install-location
exit terminal emulator
Good luck ! Hope it help you
Problem with my GT90H
Hey Guys,
I have a Problem with my GT90H. It stops to boot at the screen: Tablet PC - Keep Moving Forward.
If i go in the recovery mode. I can reboot the system, but it stops at the same screen like I explained in my first sentence.
The Factory Reset doesn't work. So I read in some communitys that Tablets can be flashed with a new ROM (Android System) over the USB Port from the Computer.
So can anybody send me the Android 4.2.2 Image for my GT90H ?
It's very important. So thanks.
Thanks for your help.
Greetings from
TheGuardianTX
Hi,
so now I have an Firmware as an Image-File at my computer, but I don't know how I can flash my tablet via ADB.
So can someone help me ?
Thanks a lot.
Greetings
TheGuardianTX

Need some help with C12R1

Please need some help with C12R1. I have this:Telechips TCC8803, 2Din Car Media Center Running Android 4.0.4 ICS
2 Din Car DVD Stereo GPS+ CD Player +MP3 +Bluetooth +Ipod +WiFi+ 3G+7 inch Android 4.0 Tablet Car PC Media
Android: ICS 4.0.4 rooted
Hardware Pad
CPU:Telechips TCC8803,1.0GHz; Cortex-A8 Kernel, 45nm processing.
RAM: DDR III 512M
ROM FLASH:4GB
Power IC:TDA 7388/LA47002/TA2929/TA2939
Extended memory card:Up to 32GB SD/TF card
WiFi:Bulit-in High performance, low power consumption, Atheros 6302 WiFi802.11b/g/n.
3G:3G Universal Drive ---Support extral USB Dongle:WCDMA,EVDO,TD-SCDMA GPS,JRC G591Receiving Module
G-SENSOR:3 axis acceleration sensor and 3D IC hardware acceleration,could realize dynamic 3D game and 3D interface.
CAMERA: support 0.3-2 Megapixels rear camera
Speaker:built-in speaker,1pc 1W,8Ohm
Micphone:built-in, high sensitivity input, right&left channel
Indicator light:built-in red charging indicator light,built-in vibration motor
Hardware CarAudio System
Operation System DVD platform
CPU:Toshiba TMP86FS49UG
Display:Supplier:Innolux
LCD:7 inch 800*480 HD, TFT digital screen, Resistive touch screen.
MODEL Nr: C12R1 (crane)
Baseband version: 1.4rc2
Kernel version: 3.0.8 [email protected] - 102 # 447
Build number: crane_C12R1-eng4.0.4 IMM76D 20131114 test-keys
took it from this thread: http://forum.xda-developers.com/showthread.php?t=2572265
My problem is I've accidentialy deleted my /system/app/* and /data/app* files trying to free some space / I wanted to copy it on extsd card with X-plore app but it didn't work out for me I've copied the files above the number of the sdcard and they're gone / don't do this it's dangerous, and I've lost all of them. And my tablet started with the errors and stuff and I wanted to throw it off the window, than I settled down for a bit.And before a week or so I've started looking for 4.0.4 roms compatitable system apps for my rom, I've tried maybe 40 roms by now /I download the rom / extract the /system/app, and /data/app folder and try to run the tablet, but it didn't work out. I managed to run it with modacocustomrom reading one of xda threads but it started throwing exceptions. Then I've started deleting one by one system apps and I've come to the conclusion that the system could run only with 3 apk's - launcher, settings and settings storage. It started but it is not the same and I've lost all my preffs and stuff.
Please if someone have C12R1 send me /system/app/ and /data/app files. for 4.0.4 android
Appreciate it. Thanks in advance.
And could you tell me how to unpack this rom (WooComet-MiOptimusOne.com -ICS_4.0.4- F1中性-20120920.1.0.3-A721_V4.2.img) from this thread - http://forum.xda-developers.com/showthread.php?t=1925577 without the device connected to pc and this program: LiveSuit.exe. I've tryed with dd in linux on flash and with mounting img in linux but it coudn't work out why?
I've tried to unpack the img with ext4 unpacker and ext2 explorer too but it couldn't work out.
please help!
Ok guys I managed to do this, I've made the last step /flashing the rom (I wanted just to copy the system files in internal memory in /system/app and /data/app but couldn't find it anywhere), I did'nt wanted to do it this way but I've done it cause it wasn't anything else left to try after long sleepless nights
I've installed a new stock rom sun4i_crane_t02a.img and android launched but now I have another significant problem - I dont have a proper driver and my touch screen does not work.
And my android's usb debugging is not with turned on and I cant use adb or so....
Any ideas?
Please if someone have this touch screen drivers or stock or other rom that works on this device please send it to me!
This is the exact device:
http://www.aliexpress.com/item/2-Di...92768377.html&cv=11032041&af=cj_6149808&vd=30
but I cant find roms anywhere for it
Hi Razer69
I see you still have problems with your device.
Well before i wend on a Rom hunt i have managed to install CWM recovery on mine and make a backup of the stock rom, in order to test various roms, and if they do not work i restore the stock.
If you want i can create a link for you so you can download it and install it. Bare in mind though i have made some mods prior to the stock rom so it worked a bit better that when it arrived.
Did also find a link for your issue with the touch screen ----> http://www.pandawillforum.com/archive/index.php?t-12129.html
Cheers
G
Could you share how did you managed to install custom rom - clockworks - CWM because that is my problem now.
I can't install the rom because I've flashed my device - all partitions - kernel, recovery, rom - with LiveSuite and .img file but eventually
I found out this rom is not for my device - the rom I've installed is C12 not C12r1, and I'm still looking for C12r1.
Thank you for your answer
I've come to the conclusion I'ts wrong rom that's why the touch screen is not working.
This guys are writing the same here:
http://www.pandawillforum.com/archive/index.php?t-12129.html
"sun4i_crane_t02a.img is not work with FT5306DE4 Chipset,is wrong point of touch screen"
Today I'll try their methods
thanks

MT6577 camera won't work after flashing stock ROM

Hi all,
I'm quite new with android and this explains why I'm here asking for help and direction to solve a problem. I've a chinese phone based on MT6577 hw; it's branded ORDRO P550 4.1.1. Well, months ago I was able to root it but after some months it started to be unresponsive and very slow. Perhaps because I moved some software from ROM to SD in order to get more free memory. In fact, MT65xx comes out with only 512 MB of ROM/RAM. So, I found and application named MT65xx_repartition and I decided to check if it did what it promised. Basically, it claims to be able to repartition the internal memory, using phone's internal memory to increase phone's RAM.
I made a backup of what I needed and I was able to find a stock ROM of the same model from a web site.
After running the repartition program my poor phone did not start up again; it only showed the small robot wit a big exclamation mark. OK, I thiught, I've the original ROM.....let's re-flash and learn something new. After several attempts to install USB drivers on my virtual Win7/64 box I was able to re-flash the ROM again. Et voila'....it was reborn but, alas, a little bit handicapped.
First of all the IMEI was wrong or not existent so I got no carrier and secondly, the camera didn't work at all.
For the IMEI issue I was able to fix it thanks to Mobileuncle Tools (fortunately I made a backup of IMEI before proceed) but I could not find a solution for the camera.
I checked and googled everywhere and I think that it could be a driver issue...something related with libcam*.so files but I have absolutely no idea how to fix them; do I need to recompile the drivers? I checked init.rc file but I found no evidence of libcam*.so modules nor any insmod instruction to load them. I'm not really familiar with linux; I'm moving my first steps with it and the only complicate thing I did was to recompile wifi drivers for my Debian Virtual box.
Here a partial list of phone's details collected by Mobileuncle Tools:
CPU
CPU ARMv7 rev 0 (v7l)
Hardware MT6577
Kernel
Linux Version 3.4.0
OS
OS brand ORDRO
Model P550T
Bootloader unknown
Prouct e1901_v77_gq2002
Display e1901_v77_gq2002_2013.03.25
Release 4.1.1
fingerprint alps/e1901_v77_gq2002
MTK Build
.platform = MT6577
.chip_ver = S01
.wlan.chip = MT6628
The main difference between this ROM and the previous one (for completeness I forgot to download) is the ROM size; now is 878MB (?) instead of the previous one that was 493 MB.
Thanks a lot for any support or direction you can give me; I'm looking for a set of instruction to solve this problem and learn something new.
PK

Can I make flashable img file for (android tool) from cwm Backup

Hi,
I'm having big problem by low level format of my tablet RK3188(chip) have no idea of model is 10' one.
I'm looking to make a flashable img files from my backup CWM recovery to use with Android tool since my tablet is unknown
china with RK3188 chip.
Perhaps someone will give me idea to allocate proper parameter for recovery , kernel , boot , etc...
Usual location for tablet RK3188 Cortex A9 Quad core 1.6 ghz Governor interactive, Kernel 3.0.36+ ,Board hardware RK30Board/ 0000, Android 4.2.2 ;eng.root 20130912.185132 sdk 17, Display 1280x800; dpi;160 size 9.4'
GPU:Mali-400MP, RAM: 2048 Flash:32 gb Build in:16gb actual, wifi, usb, Bluetooth gps= all yes, camer 5MP additional 1.9MP
Recovery, system, boot, kernel are large files in cwm I need to make them smaller (proper size) to use with Android tool. Please correct me if I'm wrong and tell me if its possible or any other way to get to my CWM .I just need to get to recovery. Please help.
Many thanks for your time.
styropian said:
Hi,
I'm having big problem by low level format of my tablet RK3188(chip) have no idea of model is 10' one.
I'm looking to make a flashable img files from my backup CWM recovery to use with Android tool since my tablet is unknown
china with RK3188 chip.
Perhaps someone will give me idea to allocate proper parameter for recovery , kernel , boot , etc...
Usual location for tablet RK3188 Cortex A9 Quad core 1.6 ghz Governor interactive, Kernel 3.0.36+ ,Board hardware RK30Board/ 0000, Android 4.2.2 ;eng.root 20130912.185132 sdk 17, Display 1280x800; dpi;160 size 9.4'
GPU:Mali-400MP, RAM: 2048 Flash:32 gb Build in:16gb actual, wifi, usb, Bluetooth gps= all yes, camer 5MP additional 1.9MP
Recovery, system, boot, kernel are large files in cwm I need to make them smaller (proper size) to use with Android tool. Please correct me if I'm wrong and tell me if its possible or any other way to get to my CWM .I just need to get to recovery. Please help.
Many thanks for your time.
Click to expand...
Click to collapse
Update __
RK3188 adb is running no screen__help PLEASE
After erasing IDB in my unknown china tablet and loosing my whole system I was able to load different custom firmware from Chuwi v88 + different kernel and my Tab popup in windows showing 2 extra drives F and G.I did open android studio and notice access to adb and all activity in my android.The RKandroidTool also recognizing my tab.
No reaction to power button only automatically connecting to my comp ( black screen on my tab).
I have original CWM backup of my device.
Can someone advise me how to access recovery from this point or find the way to completely start my tablet.Maybe is possible to recover CWM from adb?I will need some help to use a proper commands perhaps in adb.

Categories

Resources