########################################
DHT Upgrade Advisor is no longer supported
Check DHTPersonalization thread for new versions : (Current Version V0.729)
https://forum.xda-developers.com/showpost.php?p=74721954&postcount=42
########################################
Hey there everyone
Dormant Hackers Team's new app is here to help you upgrade your phone without any problem .
This app will help you to get new Redstone update and maybe later upgrades on your old lumia .
what phones are supported by this tool :
All Nokia Lumia devices and All Microsoft Lumia devices except x50 series .
What is the app features :
-Backup your Phone targeting info
-set your phone as a Microsoft Lumia 950XL for single sim devices and Lumia 950XL Dual Sim for Dual Sim devices .
-Restore your device targeting info again using this this app .
Does backup my phone really make a backup of my information ?
Actually NO . It only backup : HKLM\System\Platform\DeviceTargetingInfo and only the keys this app change them .
How to use :
-make sure you didn't changed your DeviceTargetingInfo keys, after that check the Backup my phone .
-Information of your devices will shown up in application
-Choose you device type (Single Sim or Dual Sim)
-Tap on Allow update (this will set your phone to a 950xl as I said before)
-Now you can use Windows Insider to choose your Insider Ring and upgrade your phone .
-Better to Restore backup of your device after upgrade .
if the above instruction didn't worked
-download and install latest version of interop tools app http://forum.xda-developers.com/win...interop-tools-appx-windows-10-mobile-t3373675
-Go to Interop unlock section and try to Restore NDTKSVC (Attention : Restore NDTKSVC Not that one ends with (x50))
-then reboot your device and try to Interop/cap unlock your device again from Interop Tools app ->Interop Unlock section
if the above instruction didn't worked again FINAL WAR:
Thanks to @Mafworld
for the full instruction below :
1- Make a hard reset.
2- setup your phone after hard reset, avoid WIFI or mobile data access on your phone.
2.1- once your device is done, go to developer options and enable developer mode.
3- download and install DHTUpgrade Advisor + Dependecies via file explorer or sideload via device portal
4- Download and Install Interop Tools 1.7 and open the app and hit on Restore NDTKSvc (This will help you to change the Registry, Some users are facing error trying to hit button "Allow Update" "Allow Update 512MB")
4.1- Open DHTUpgrade Advisor and hit "Allow Update 512MB devices" or "Allow Update"
4.2- in settings> sytem> about. check your device info, in case appears the original targetting info restart your device normally.
5- go to windows store and deactivate "Auto Update Apps", we want to stay away from Extras&Info.
6- Install Upgrade Advisor via Windows Store.
7- Once Installed open Upgrade Advisor and follow the steps, if upgrade advisor say you're up to date or there are no updates! its okay.
8- go to settings> update & security> phone update> check for updates...
-updates available
windows 10 mobile ( 10.0.14393.67)
this update helps your device work even much better.
9-done.
This is a open source project, so feel free to change it by your own .
What this app contains for starter developers ?
This source code is a real simple code to see how SplitView , RelativePanel , VisualStateManager works , but it's really basic and easy to understood .
Test for 512 MB devices :
guys with 512MB of devices test this :
http://forum.xda-developers.com/attachment.php?attachmentid=3844546&d=1471383596
first check Backup , Then Tap on Allow Update(for 512MB Ram)
Thanks all guys who find trick for 512 devices and I will add their names soon in thread .
What are the files uploaded ?
DHTUpgradeAdvisor_1.1.4.0_arm_Debug.rar : it contains the appx file and you must be able to deploy it with Developer Mode enabled via file manager .
Dependencies.zip: this contains ARM dependency packages needed for app . (if you weren't able to deploy this app using file manager use device portal to deploy using appx file and these dependencies .
Source.rar : surely it's the source code of my app .
Technical Information about source :
Visual Studio 2015 Update 3 , Universal Windows SDK 10586 (v1.4)
Credits :
Thanks to @Mafworld
-Thanks to @BlueTR for finding hack to get update on 512MB ram devices
-Thanks DHT Guys : @djamol @vcfan @ngame
-Thanks @raghulive for sharing this hack on this topic : http://forum.xda-developers.com/win...windows-mobile-10-redstone-rs1-build-t3319375
-Thanks to MahGraphic Studios Team and Iranian guys for their supports
Reserved
[Q]Old you mean even with 512mb RAM?
[A]I mean Unsupported Phones .
for now 512MB RAM Phones no but work on 1GB ram devices .
I still don't know why getting builds doesn't work on 512 MB rams , but I'm doing research for it .
Guys with 512MB Ram devices test this :
Test for 512 MB devices :
guys with 512MB of devices test this :
http://forum.xda-developers.com/attachment.php?attachmentid=3844546&d=1471383596
first check Backup , Then Tap on Allow Update(for 512MB Ram)
Thanks all guys who find trick for 512 devices and I will add their names soon in thread .
Old you mean even with 512mb RAM?
djtonka said:
Old you mean even with 512mb RAM?
Click to expand...
Click to collapse
I mean Unsupported Phones .
for now 512MB RAM Phones no but work on 1GB ram devices .
I still don't know why getting builds doesn't work on 512 MB rams , but I'm doing research for it .
I was just curious, Marass will make it, RS ROM for 520 too
djtonka said:
I was just curious, Marass will make it, RS ROM for 520 too
Click to expand...
Click to collapse
Yes , I exactly want RS on 520 only for skype.
Does it work for updating to W10M from WP8.1 too?
mahdi75 said:
Does it work for updating to W10M from WP8.1 too?
Click to expand...
Click to collapse
Nope. I have to poke around for 8.1 users .
Just to be clear, by "redstone" you mean Windows 10 Anniversary Update build 10.0.14393.5 ?
w.bogdan said:
Just to be clear, by "redstone" you mean Windows 10 Anniversary Update build 10.0.14393.5 ?
Click to expand...
Click to collapse
Yup
ngame said:
Yup
Click to expand...
Click to collapse
One more thing, which are the "old Lumias" that benefit from this app? The reason I'm asking is because when this thread Redstonebuild 14267& higher for old lumias was started, Lumia 735 was one of the unsupported phones. Now, I got 10.0.14393.5 with Windows Insider in the Release Preview ring.
w.bogdan said:
One more thing, which are the "old Lumias" that benefit from this app? The reason I'm asking is because when this thread Redstonebuild 14267& higher for old lumias was started, Lumia 735 was one of the unsupported phones. Now, I got 10.0.14393.5 with Windows Insider in the Release Preview ring.
Click to expand...
Click to collapse
As I said this app makes it easier to get updated. You can use registry editors freely to modify keys by your own but in this way you will save your Phone targeting info to restore and change your phone identity easier .
ngame said:
As I said this app makes it easier to get updated. You can use registry editors freely to modify keys by your own but in this way you will save your Phone targeting info to restore and change your phone identity easier .
Click to expand...
Click to collapse
Don't get me wrong, it's a great app and we thank you for it. I just wanted to make things clear. For my phone, Lumia 735, no registry edit was necessary yesterday to get to redstone. However, I'm sure your app will be very helpful in the future for other updates Microsoft might consider my phone is not fit.
w.bogdan said:
Don't get me wrong, it's a great app and we thank you for it. I just wanted to make things clear. For my phone, Lumia 735, no registry edit was necessary yesterday to get to redstone. However, I'm sure your app will be very helpful in the future for other updates Microsoft might consider my phone is not fit.
Click to expand...
Click to collapse
Uhum fortunately Lumia 735 is still getting updates without any problems .
w.bogdan said:
Don't get me wrong, it's a great app and we thank you for it. I just wanted to make things clear. For my phone, Lumia 735, no registry edit was necessary yesterday to get to redstone. However, I'm sure your app will be very helpful in the future for other updates Microsoft might consider my phone is not fit.
Click to expand...
Click to collapse
I think Lumia 735 is a supported phone to get Redstone. That's why no registry editing is necessary to get RS. This app is for those Lumia's (Like Lumia 1020, 920, 925...) which are not supported to for Redstone update officially.
Seriously, if you don't know how the 512MB block works, don't even bother. I took a quick look at the source and it's clear that you've just built a tool which automates some registry editing without having any knowledge of how the actual update gets picked up or how updating a phone even works. There is a lot of redundant code in there.
Do I need to interop unlock my phone or anything similar for this to work ? Because I just followed the steps in OP and no updates come up.
plantroon said:
Do I need to interop unlock my phone or anything similar for this to work ? Because I just followed the steps in OP and no updates come up.
Click to expand...
Click to collapse
Thanks to the authors not knowing how the NDTK RPC works and what sort of permission set it needs, you do need interop.
plantroon said:
Do I need to interop unlock my phone or anything similar for this to work ? Because I just followed the steps in OP and no updates come up.
Click to expand...
Click to collapse
No you have to only enable Developer Mode on your phone . I test this on a non-Interop unlocked phone 640XL LTE Dual sim and it works .
ngame said:
I mean Unsupported Phones .
for now 512MB RAM Phones no but work on 1GB ram devices .
I still don't know why getting builds doesn't work on 512 MB rams , but I'm doing research for it .
Click to expand...
Click to collapse
Yeah... I really want it too on 520... Hopefully, I can receive your good news soon
Related
As many S/W co. required to license it's product to their user, many required you to have the Device ID to install. I know one of them is Mapping / GPS S/W; Destinator.
Other devices, this no. is included / reported under Device Information (Start > System > Device Information), but unique to this mdl. it is not listed (other HTC made products have it), so the Question is how do you find it?
I called the HTC Support (outsourced to India / Pakistan I think, all of my 3 calls answered by their accented tech supports), low level tech know nothing, even they don't know if such exist. After this call, I kept searching and accidentally stumble to Windows Update Icon in Settings and attempted to do the update. Unexpectedly, the update was completed w/o any, my system is up-to-date, I supposed, and in the log report through this process, there it is ... the Device ID no. is revealed.
I called HTC support again, and discuss this particular subject, as I expected, this 2nd low level tech support do not know anything too, just as the first. So, I asked to be connected to the supervisory tech support and was promised that he would call me back.
The supervisor tech support called approx. 45 min. later. Yes, as I expected, he insisted that no such thing in this device known as the Device ID, though I mentioned to every one (all 3 of them), that, such, existed in my other 10+ previous devices I owned and majority of them are made by HTC.
And, obviously we debated and they feel strongly that they know better ... hallooo ... they may do on other subject, but on this particular one ... ??? ??? ???
My point is: I sincerely hope that their (HTC team that developed the x7501) to include this information in their future update (either through ROM or Device Info) so we can use S/W that requires it.
Hallooo ... ooo ... HTC ... ... ...
So, for you that need this info, here is how:
Start > Settings > System > Windows Update ... and view / read the log after finish, in it you will find your unique Device ID and IMEI no. as well (the IMEI no. is also available through Device Information)
Device ID on Advantage x7501 / Athena
Forgot to mention:
You need to be connected to the Internet to get the update and produce the log!
Sorry guys n gals ...
Thanks, I haven't needed that info yet, but nice to know where I can get it.
Device ID
hi everybody,
i just want 2 know how can i find my ( Device ID ) for my Htc Hero.
thnx alot.
joker5089 said:
hi everybody,
i just want 2 know how can i find my ( Device ID ) for my Htc Hero.
thnx alot.
Click to expand...
Click to collapse
searching for your answer here would be agood start
http://forum.xda-developers.com/forumdisplay.php?f=511
Devise id
Thanks for the info
But i have a htc touch 2
And it does not have an windows update in the settings, so any help for my problem?
As im trying to install tom-tom and activate maps and download maps and it is asking for my devise id
and it gives me an example : A1B2.....
hkusuma said:
So, for you that need this info, here is how:
Start > Settings > System > Windows Update ... and view / read the log after finish, in it you will find your unique Device ID and IMEI no. as well (the IMEI no. is also available through Device Information)
Click to expand...
Click to collapse
And if you do not have Windows Update on your device like on mine, using the Athena_SPL1.2_WM6.1_B20931_WWE_R6.1-MiChY
Hi,
I first tried the method below:
Is someone trying to develop a Custom ROM for the Huawei Ascend G600 (U8950D)?
http://forum.xda-developers.com/showthread.php?t=1943003
But the phones are not just different band versions, as mentioned in post 58 of the thread above. The T8950 is not kernal compatible with the U8950D:
http://www.jetdroid.org/forum/viewtopic.php?f=106&t=8383
Indeed, the T8950 is equipped with MTK6517 dual-core processor, the MT6517 and MT6577 are the same, A9 architecture 40nm processor, clock ed speed is 1.0Ghz.
http://defendgun.com/2013/01/22/mobile-customized-huawei-glory-t8950-listed-price-at-261/
I don't pretend to have any knowledge about rooting phones, I just was able to find the correct information on the web. I spend two weeks figuring this out. So I hope I can save somebody else his time with this information.
this is how I did it.
UNLOCKING THE BOOTLOADER
--------------------------------------------------
the bootloader of the T8950 is not locked, so it does not need to be unlocked. Allight, step one done!
INSTALLING THE CMW CUSTOM RECOVERY TOOL
------------------------------------------------------------------------------
The T8950 does indeed not have a fastboot mode. the CWM custom recovery can be installed by flashing the ROM using the Flash tool of Mediatek
tutorial: http://bm-smartphone-reviews.blogspot.com/2012/05/mt6575-flashing-tutorial.htmlthe correct files to use in the tutorial can be found here:
- SP_Flash_Tool_exe_v3.1224.01 --> http://www.mediafire.com/?c8lr368ceaqk7tv
- MediaTek DA USB VCOM drivers --> http://www.mediafire.com/?h0ytkyagj0kf89u
if all went well, you should have a different recovery screen now.
ROOTING
-----------
Tutorial: http://bm-smartphone-reviews.blogspot.com/2012/02/complete-guide-to-clockworkmod-recovery.html
The fileto be used is:
- RootT8950.zip --> http://www.mediafire.com/?je47wz2ozjr7oth
After the update is finished, reboot . Now, you should see Superuser in your Huawei T8950 app list. You can double check if you have root, using the "got root?" app.-->https://play.google.com/store/apps/details?id=com.island51.gotroot
INSTALLING THE GOOGLE SERVICES
----------------------------------------------------------
Since the the CWM custom recovery tool is installed now and the phone is rooted, it's very simple to add the google services to the phone. I used the GAPPS of Cyanogen. You can find them on many places, e.g.
http://www.needrom.com/mobile/gapps-cyanogen/
choose the right version, most likely your T8950 will have android ICS 4.0.4
istallation is the same as installing the rooting ROM
REFERENCES
----------------------
http://bm-smartphone-reviews.blogspot.com/2012/05/mt6575-flashing-tutorial.html
http://bm-smartphone-reviews.blogspot.com/2012/02/complete-guide-to-clockworkmod-recovery.html
http://www.aiothudanu.com/2013/01/huawei-t8950-install-cwm-recovery-and.html
http://forum.xda-developers.com/showthread.php?t=1911475
http://www.needrom.com/mobile/gapps-cyanogen/
Regards,
TeTTiweTTi
Hey TeTTiweTTi!
I can not say how glad I am that you wrote this tutorial. It seems that this is actually the only tutorial on how to truly unlock the T8950 (at least for non russian-speakers )
Still, I'd have some questions:
How do you install the VCOM driver? I downloaded it, but I can only find .inf files.. How do you install them?
Did you flash the whole ROM or just a part of it, as shown in the tutorial? And what exactly happens when you flash the ROM? Are you able to boot afterwards? It seems to just install CWM - right?
How do you apply the update RootT8950.zip?
Help would be appreciated a lot, since you seem to be the only one who knows how to properly do it
Oh and btw: did everything work for you after flashing the ROM? Or did you encounter any errors?
Cheers,
amannn
Hi, it was indeed not so easy to collect these bits and pieces together
here an answer to your questions
1.
The .inf files are the drivers. There are two ways to install the drivers. One way is to right click on the .inf file and choose "Install". The other way is to start the process with SP Flash Tool and as soon as you plug in the phone a new device will be detected and you have the choice to install the drivers.
Also, it is very important to make sure that you click "Download" first before you connect the device. Actually there is a trick, below the sp flash tool, you will see something that says "USB". Click "Download" and wait for the "USB" to become "Searching". Once it is "searching" then connect the USB. SP-Flashtool should be able to capture it before it disconnects itself again.
2.
yes, you only flash a part of the ROM, so you don't need to have all the files in the SP Flash Tool. Only the ones mentioned in the tutorial. Your phone will boot normal, nothing will be changed yet. But now you will have the CWM custom recovery when you start up in recovery mode.
3.
the linked tutorial is quite clear. Let me know if you cannot reach the page or you encounter a problem.
Regards,
TeTTiweTTi
Sent from my ASUS Transformer Pad TF700T using xda app-developers app
Hey TeTTiweTTi!
Thank you very much again for your detailed explanation!
So i think I've installed CWM recovery successful. Therefore, I'm now working on the rooting part.
The RootT8950.zip file needs to be applied, using the "choose zip from sdcard" option from CWM recovery right? When I choose that option, I encounter the error "E:Can't mount /sdcard/". Also when I'm trying to create a backup, it says "Can't mount backup path.". So it seems that there is a problem with accessing the sdcard. I then tried the "mount /sdcard" option, but it also says "Error mounting /sdcard".
Did you have any problem like that? When my phone is booted up, there is no problem with accessing the sd card... Or is there a option how I can check if the sd card is inserted correctly? I guess it's internal and therefore impossible to even remove it..
Your help would be highly appreciated!
Many thanks in advance and best wishes,
amannn
EDIT: I was now able to upload the update with an external micro sd. Therefore everything works so far - thanks again
Similar phone mtk6517 svp s580
Hi
I have this. svp. Phone with ARMV7 ( see cpuz snapshot
)
It says mkt6517 with A5 cortex
I tried jnstalling all drivers linked here for ADB
but windows xp disqualified em as valid drivers for this hardware
Finally I got android device driver to install on
All 3 devices ( see pic- there are 3 devices
That show up )
I don't think this generic driver is the right one
So rooting this is still not done .does anyone hace luck with this device
Any idea ......? With getting the right driver and root
Procedure
I tried eroot too amongst other rooting s/w's
CPU screenshot
CPU screenshot
sieger007 said:
Finally I got android device driver to install on
All 3 devices ( see pic- there are 3 devices
That show up )
I don't think this generic driver is the right one
So rooting this is still not done .does anyone hace luck with this device
Any idea ......? With getting the right driver and root
Procedure
I tried eroot too amongst other rooting s/w's
Click to expand...
Click to collapse
Hi sieger007,
It can be a little bit tricky to install the drivers, since it are .inf files only. But these are the driver files
http://bm-smartphone-reviews.blogspot.be/2012/05/mt6575-flashing-tutorial.html said:
There are two ways to install the drivers. One way is to right click on the .inf file and choose "Install". The other way is to start the process with SP Flash Tool and as soon as you plug in the phone a new device will be detected and you have the choice to install the drivers.
It is very important to make sure that you click "Download" first before you connect the device. Actually there is a trick, below the sp flash tool, you will see something that says "USB". Click "Download" and wait for the "USB" to become "Searching". Once it is "searching" then connect the USB. SP-Flashtool should be able to capture it before it disconnects itself again.
Click to expand...
Click to collapse
This second way worked just fine for me.
You can find the drivers and tools also here
http://mt65xx-tools.4shared.com/
he password to login is bm-smartphone-reviews.blogspot.com.
But always make sure that you trust the sources of the ROM you download and know that it is meant for your phone. After flashing a wrong preloader, your phone will be completely dead (can't be powered on, it will not charge and won't be detected anymore by the computer) and there is no way to recover it.
In order to root you first need to install a custom recovery. In this case it is CWM.
hope this helps
still stuck in driver hell
thanks for your help . I had a previous Chinese MTK (MT6575 ARM A9 cortex ) phone , whose ADB drivers successfully installed when I installed the SDK .
Now this one is MTK6517 ARM A5 Cortex. and none of the methods ( #1 or #2 ) help, in those drivers being recognized.
By method #1 : Right click install - It maybe just copying the driver file to system folder and then on windows would auto detect it when the device is inserted -assuming there is a match .
Method # 2 : Uses the new h/w found dialogue . Not sure if invoking sp_tool is related anyways in invoking that dialogue . It shows up anyways - soon as you plug in the phone .
I could not get the driver files in with the blogspot password to be recognized . Kept giving me "specified location. does not contain info about your h/w msg"
I have the EXACT same problem with ALL drivers hunted on the net , that say MTK driver. Some files say MTK65xx some say MTK_USB_Driver etc.
the h/w ID's and instance IDs associated with the devices are attached .
USB\VID_1782&Pid_5d04&Rev_0229&MI_01
Now the driver.inf file did have one ray of hope with this mention ..wonder if that'd make it compatible with a modified inf file.
But I am lost about HOW to add the h/w ID info ( format and what specific data to add ) to the inf file -most data is of the form VID_eXXX something in that file ( see below quote )
MT6516 USB VCOM drivers\readme.txt
Code:
3. Customers can customize usb2ser_XXX.inf file.
There is a string in the file:
MTK6218 = "USB Modem Driver"
You can modify it for your product name, for example:
MTK6218 = "MY_PRODUCT Modem Driver"
The other perplexing thing is that there are 3 Devices that show up under XP device manager. I managed to get one of em installed as device "android phone" with driver "android ADB interface" from Google and can possibly manage to get ALL of em installed the same way since those device ID's are close ( the last '1' becomes 2 and 3 respectively ) in this
Code:
USB\VID_1782&Pid_5d04&Rev_0229&MI_01
After pushing all these device ID's as "android ADB interface" - and attempting to root- the android rooting s/w's will NOT work at the identification step , erring out with "ADP device not found "- conclusively indicating that those drivers probably did not work well and I ought to look around for better ones - something I am trying to address by this thread.
Lastly - sp_tool when you start it - it will ask for scatter file. The scatter file out there is for MTK6577 (vs my model 6517 ) . If I choose that file - it gives me a warning - yes it out - and click download - it will then just freeze doing nothing
after some more G-mining ( Google) - i found out that I have to stick my VID in that hardware ID's and create an adb_usb.ini file to get the device recognized. Will update on happened next
sieger007 said:
after some more G-mining ( Google) - i found out that I have to stick my VID in that hardware ID's and create an adb_usb.ini file to get the device recognized. Will update on happened next
Click to expand...
Click to collapse
good luck!
That's why I stay away from these little brands. It's very difficult to find good information for it.
found something !!! I hope this is perm and not "leased"
TeTTiweTTi said:
good luck!
That's why I stay away from these little brands. It's very difficult to find good information for it.
Click to expand...
Click to collapse
TeTTiweTTi said:
good luck!
That's why I stay away from these little brands. It's very difficult to find good information for it.
Click to expand...
Click to collapse
ADB driver issue
> adb_usb.ini needed oXXXX as device ID . Where XXXX is the ID that shows up on Device manager. This is detailed here
http://blog.fh-kaernten.at/wehr/?p=1182
after that there will be 2 yellow marks for the rest of the unknowns in device manager. for this you have to modify the .inf file to include the entire h/w ID strings. I guess that makes just about any driver get along with anyone unknown - so here I am not sure if showing them as the such h/w by changing the driver files - gives them the actual intended functionality or all it does it just makes the device manager look clean without yellow marks. Maybe someone could help expand the talk here
[
Code:
android_winusb.inf
%SingleAdbInterface% = USB_Install, USB\VID_0BB4&PID_0C01
%CompositeAdbInterface% = USB_Install, USB\VID_1782&PID_5D04&MI_01
/*ADDED*/
%CompositeAdbInterface% = USB_Install, USB\VID_1782&PID_5D04&MI_02
%CompositeAdbInterface% = USB_Install, USB\VID_1782&PID_5D04&MI_03
So with that - I get 1 ADB interface and 3 devices show up under "com and LPT" - alright that completes the drivers
ROOTING
I found this Chinese rooting program Vroot . I still have'nt figured out what exactly it means but it looks like it DID root that sucker after all. I tested with one app - root checker - got an dialogue in Chinese , asking me whether to give or not and I think I said Y but that app still does not say I have root. Its probably the apps thats at fault because I can get Linked2SD do ALL the stuff it would be doing running as root - .e.g force move programs to SD to free up space etc.
If someone out there can make English out of that and tell me if its mine to keep or leased out ( trial ) - that'd be damn nice !!!
ROMS
- WIP- when I get some more time
the chinese rooting program - now hiring English interpreters
the chinese rooting program - now hiring English interpreters
sieger007 said:
ADB driver issue
> adb_usb.ini needed oXXXX as device ID . Where XXXX is the ID that shows up on Device manager. This is detailed here
http://blog.fh-kaernten.at/wehr/?p=1182
after that there will be 2 yellow marks for the rest of the unknowns in device manager. for this you have to modify the .inf file to include the entire h/w ID strings. I guess that makes just about any driver get along with anyone unknown - so here I am not sure if showing them as the such h/w by changing the driver files - gives them the actual intended functionality or all it does it just makes the device manager look clean without yellow marks. Maybe someone could help expand the talk here
[
Code:
android_winusb.inf
%SingleAdbInterface% = USB_Install, USB\VID_0BB4&PID_0C01
%CompositeAdbInterface% = USB_Install, USB\VID_1782&PID_5D04&MI_01
/*ADDED*/
%CompositeAdbInterface% = USB_Install, USB\VID_1782&PID_5D04&MI_02
%CompositeAdbInterface% = USB_Install, USB\VID_1782&PID_5D04&MI_03
So with that - I get 1 ADB interface and 3 devices show up under "com and LPT" - alright that completes the drivers
ROOTING
I found this Chinese rooting program Vroot . I still have'nt figured out what exactly it means but it looks like it DID root that sucker after all. I tested with one app - root checker - got an dialogue in Chinese , asking me whether to give or not and I think I said Y but that app still does not say I have root. Its probably the apps thats at fault because I can get Linked2SD do ALL the stuff it would be doing running as root - .e.g force move programs to SD to free up space etc.
If someone out there can make English out of that and tell me if its mine to keep or leased out ( trial ) - that'd be damn nice !!!
ROMS
- WIP- when I get some more time
Click to expand...
Click to collapse
sieger007 said:
the chinese rooting program - now hiring English interpreters
Click to expand...
Click to collapse
Post some screenshots of the text you want translated and I will ask the help of one of my Chinese colleagues.
Sent from my ASUS Transformer Pad TF700T using xda app-developers app
some screenshots of the text you want translated
here goes ..thank you . Combined several screens together in '4 lets '
TeTTiweTTi said:
Post some screenshots of the text you want translated and I will ask the help of one of my Chinese colleagues.
Sent from my ASUS Transformer Pad TF700T using xda app-developers app
Click to expand...
Click to collapse
sieger007 said:
here goes ..thank you . Combined several screens together in '4 lets '
Click to expand...
Click to collapse
ROM Basic Information Huawei T8950 Emotion UI 1.6 official pure version of the card brush pack
Author: Hay.
Size: 398MB
Android Version: 4.1.2
UI type: official factory style
Suitable models: Huawei T8950
Release date: 2013-07-31
MD5 code: F7A21630317EE4239DC145E75FF8A276
ROM presentation
1, based on the official code base package and Qualcomm made to upgrade to 4.1.2
2, emui upgrade to 1.6
3, repair legendary SMS unlit issue
4, full root privileges
5, caused during an upgrade wifi loss problem to fix
6, clean up some pit length useless underlying file
7, adjust the signal and the network connection speed
8 streamlining TTS voice database file
9, usb debugging is enabled by default
10 to adjust the overall Desktop Note: Upgrading from 4.0 to 4.1 need to upgrade Bottom bag bottom package
download address: http://pan.baidu.com/share/link?shareid=805743044&uk=137718883
recover before upgrade to upgrade the official recovery Brush back REC official and third-party tools
brush download address: HTTP :/ / pan.baidu.com / share / link? shareid = 807162397 & uk = 137718883
1.6 EMUI ROM Download: http://t.cn/zQWgp1r
3G not accessible
Hi again,
so I've been struggling with another issue.
Somehow my T8950 isn't capable of connecting to the 3G network of my carrier. When I search for networks, only the 2G networks are being found.
Does anybody have a clue why that is and how to solve that problem? My carrier is from Austria and is called "tele.ring" which is operated by T-Mobile.
I'd really appreciate your help, since 2G is reaaally slow for data connections
EDIT: I just tried allowing my phone only to connect to 3G networks by using the Network app from Philipp Mangelow (which shows the same menu as if you dial *#*#4636#*#* as i just found out). This results into no 3G networks being found at all.. I thought maybe the problem occurs because I'm always connected in roaming mode. As I bought the phone in China, it seems to believe that i need to be in roaming mode to connect to my local carrier. However, I have a local SIM-card, so this is somewhat weird..
EDIT 2: So after some googling I've found out that China has the TD-SCDMA radio interface for 3G (at least China Mobile, and that's from where I've bought the phone), but in europe it's W-CDMA.. Remains the question how to change that (if possible at all)..
EDIT 3: So I've wrote an email to Huawei about the issue, and that's the reply:
Sorry that T8950 doesn’t support the W-CDMA mode.
Below please kindly check the frequence band of T8950 for your reference.
• GSM/EDGE：900/1800/1900MHz
• TD-SCDMA：A frequency（2010-2025MHz）/F frequency（1880-1920MHz)
So that means that there is nothing i can do about it?
Thanks and all the best,
amannn
amannn said:
Hi again,
so I've been struggling with another issue.
Somehow my T8950 isn't capable of connecting to the 3G network of my carrier. When I search for networks, only the 2G networks are being found.
Does anybody have a clue why that is and how to solve that problem? My carrier is from Austria and is called "tele.ring" which is operated by T-Mobile.
I'd really appreciate your help, since 2G is reaaally slow for data connections
EDIT: I just tried allowing my phone only to connect to 3G networks by using the Network app from Philipp Mangelow (which shows the same menu as if you dial *#*#4636#*#* as i just found out). This results into no 3G networks being found at all.. I thought maybe the problem occurs because I'm always connected in roaming mode. As I bought the phone in China, it seems to believe that i need to be in roaming mode to connect to my local carrier. However, I have a local SIM-card, so this is somewhat weird..
EDIT 2: So after some googling I've found out that China has the TD-SCDMA radio interface for 3G (at least China Mobile, and that's from where I've bought the phone), but in europe it's W-CDMA.. Remains the question how to change that (if possible at all)..
EDIT 3: So I've wrote an email to Huawei about the issue, and that's the reply:
Sorry that T8950 doesn’t support the W-CDMA mode.
Below please kindly check the frequence band of T8950 for your reference.
• GSM/EDGE：900/1800/1900MHz
• TD-SCDMA：A frequency（2010-2025MHz）/F frequency（1880-1920MHz)
So that means that there is nothing i can do about it?
Thanks and all the best,
amannn
Click to expand...
Click to collapse
No, unfortunatly not. this is not a software setting, but a different hardware chip. my t8950 also does not support 3G in Belgium
TeTTiweTTi said:
No, unfortunatly not. this is not a software setting, but a different hardware chip. my t8950 also does not support 3G in Belgium
Click to expand...
Click to collapse
Mmmmh, ok – that's what i thought too.
Thank you very much anyway for your response TeTTiweTTi!
**Update 02/11/2015**
Google made some changes on the back end, so the url I was using "http://m.youtube.com/watch?ajax=1&tsp=1&v={0}&dummy={1}"; now returns a "redirect" message instead of the expected data. I can get it to work, but it will be ugly as I need to now manually parse the info out of the mobile html page.
I am leaving this up as it appears to be still working in other countries.
********
All,
Here is the official patched Youtube app! Hopefully this will tide everyone over until Google and Microsoft stop fighting!
Special thanks to @AlvinPhilemon for providing the unencrypted xap!
Special thanks to @Topogigi for spurring me on this afternoon.
I am uploading two versions:
1. Youtube_Interop.xap for interop-unlocked devices that can use ID_CAP_MEDIALIB_PHOTO_FULL
2. Youtube_NoInterop.xap for developer unlocked devices.
If you are having trouble using the "Application Deployment" tool located in the Windows Phone 8 SDK(keep getting an error that says "Error - Deployment optimization failed due to an invalid assembly. Rebuild your source projects and try again."), use the deployment tool that comes with WP8 PowerTools. http://wptools.codeplex.com/
Enjoy and post your results!
Don't forget to say "Thanks!"
**EDIT**
I have updated the versions in this post to include a properly compiled version of "YouTube.TaskAgent.dll" This should take care of any AV warnings with the original version.
This dll controls the live tiles! let me know if they still work.
**EDIT 2* I accidentally uploaded the wrong version of the Youtube_Interop_P2.xap earlier. It has the wrong "YouTube.ViewModel.dll" in it.
***P3 UPDATE***
All, I give you the P3 Update! It includes the following Fixes & Enhancements:
1. Vevo/Encrypted videos should be working for now. (Hopefully Youtube won't update their API for a while lol)
2. I removed that pesky "the content owner did not make this available for mobile" message. (It looked implemented wrong anyways)
3. This version comes with 100% less ads (Felt like "sticking it to the man" lol)
4. COMMENTS now work 100%
***P3.1 UPDATE***
1. "High Quality" mode working again! Fixed all videos default to pulling from m.youtube.com regardless of encryption status.
***P3.2 UPDATE***
1. "High Quality" mode working for ALL VIDEOS INCLUDING ENCRYPTED!!!
Things that still need work:
1. Video Upload is broken still. I will take a look at it as I have time...I am guessing it is a parsing issue. The Interop-Unlocked version may "just work" on an ATIV S for uploads. I need someone to test.
2. I would like to update the signature decryption methods to make it ia bit more "future-proof". IF anyone knows a good way to parse the html5 player, I may give that a shot.
As always, Enjoy and thanks for all the feedback and support!
compu829 said:
Enjoy and post your results!
Don't forget to say "Thanks!"
Click to expand...
Click to collapse
Awesome! However, when I try to deploy to my Dev Unlocked Lumia 1020, I get the following:
Error - Deployment optimization failed due to an invalid assembly. Rebuild your source projects and try again.
Click to expand...
Click to collapse
Great!
Interop unlock version working a charme here on an Ativ S. It's a pleasure to see the official youtube working again. Grab it while it lasts!
P.S. No need to thank me, BTW: It's only the way this board is intended to work.
do you have any idea why Avast! thinks its a virus?
"Infection Blocked
URL:
http://dl.xda-developers.com/attachdl/ce281cae8898e2...
Infection:
Win32:Evo-gen [Susp]"
Many thanks for this, mate :good:
Shahar28 said:
do you have any idea why Avast! thinks its a virus?
"Infection Blocked
URL:
http://dl.xda-developers.com/attachdl/ce281cae8898e2...
Infection:
Win32:Evo-gen [Susp]"
Click to expand...
Click to collapse
for me too this xap is notified as a malware
compu829 said:
All,
Here is the official patched Youtube app! Hopefully this will tide everyone over until Google and Microsoft stop fighting!
Special thanks to @AlvinPhilemon for providing the unencrypted xap!
Special thanks to @Topogigi for spurring me on this afternoon.
I am uploading two versions:
1. Youtube_Interop.xap for interop-unlocked devices that can use ID_CAP_MEDIALIB_PHOTO_FULL
2. Youtube_NoInterop.xap for developer unlocked devices.
Enjoy and post your results!
Don't forget to say "Thanks!"
Click to expand...
Click to collapse
you can do it for windows phone 7.8?
@Shahar28 @znial It is being flagged as "malware" because I hex-edited a new developer key into the "YouTube.TaskAgent.dll" file. If you want to unzip it, and make your AV check all the files individually, that is the one it will complain about. This was more efficient instead of de-compiling and re-compiling because only one thing needed to be changed. As a byproduct of this, none of the checksums built into the dll match anymore.
@onlinespending what tool are you using to deploy this? I used the built-in "Application Deployment" tool built into the WP8 SDK. I am guessing it is complaining due to what I said above.
@josaya Windows Phone 8 only. Plus you lucky WP7.8 users have plenty of nice youtube clients written by OEMs and other developers, like HTC
compu829 said:
@Shahar28 @znial It is being flagged as "malware" because I hex-edited a new developer key into the "YouTube.TaskAgent.dll" file. If you want to unzip it, and make your AV check all the files individually, that is the one it will complain about. This was more efficient instead of de-compiling and re-compiling because only one thing needed to be changed. As a byproduct of this, none of the checksums built into the dll match anymore.
@onlinespending what tool are you using to deploy this? I used the built-in "Application Deployment" tool built into the WP8 SDK. I am guessing it is complaining due to what I said above.
@josaya Windows Phone 8 only. Plus you lucky WP7.8 users have plenty of nice youtube clients written by OEMs and other developers, like HTC
Click to expand...
Click to collapse
Gli utenti di Windows phone 7 sono i figli di nessuno!
compu829 said:
@onlinespending what tool are you using to deploy this? I used the built-in "Application Deployment" tool built into the WP8 SDK. I am guessing it is complaining due to what I said above.
Click to expand...
Click to collapse
Yeah, I'm using the built in Application Deployment as part of the WP8 SDK. I was able to sideload a decrypted swapchat.xap I found, so I can certainly side load other xaps. Is there anyway to decompile and recompile the DLL as you suggested? Would love to get this working.
---------- Post added at 03:59 PM ---------- Previous post was at 03:55 PM ----------
djadry said:
Many thanks for this, mate :good:
Click to expand...
Click to collapse
Did you try this on your Lumia which isn't interop unlocked. So far I've only seen people claim success that have used it on the interop unlocked ATIV S.
onlinespending said:
Did you try this on your Lumia which isn't interop unlocked. So far I've only seen people claim success that have used it on the interop unlocked ATIV S.
Click to expand...
Click to collapse
I've tried the Interop version on the Ativ and the NoInterop on the 820. They both work. :good:
onlinespending said:
Yeah, I'm using the built in Application Deployment as part of the WP8 SDK. I was able to sideload a decrypted swapchat.xap I found, so I can certainly side load other xaps. Is there anyway to decompile and recompile the DLL as you suggested? Would love to get this working.
Click to expand...
Click to collapse
I just uploaded a new version with the dll properly compiled, instead of hex-edited. Make sure you are installing the "NoInterop" version. Let me know if it works!
@Shahar28 @znial You guys might want to check out this new version and see if the AV warnings go away.
compu829 said:
I just uploaded a new version with the dll properly compiled, instead of hex-edited. Make sure you are installing the "NoInterop" version. Let me know if it works!
Click to expand...
Click to collapse
Does not work for me. Went back to the first one w/o problems, though. Tested only the InteropUnlocked.
@compu829 - the avast still gives out the virus warning.
Topogigi said:
Does not work for me. Went back to the first one w/o problems, though. Tested only the InteropUnlocked.
Click to expand...
Click to collapse
any specific errors?
Tested on virustotal.com no virus found
https://www.virustotal.com/fr/file/...2a49af6e36ae2e1fdbcac9a1/analysis/1384456590/
tried installing both versions on my interop unlocked ativ s. received the following error:
Error - Deployment optimization failed due to an invalid assembly. Rebuild your source projects and try again.
Shahar28 said:
tried installing both versions on my interop unlocked ativ s. received the following error:
Error - Deployment optimization failed due to an invalid assembly. Rebuild your source projects and try again.
Click to expand...
Click to collapse
What OS are you on? is it Windows 8.1? I am running windows 7 and deployed it with no problems. maybe it is a VisualStudio update to the deployment tool that is borking things. See if you can deploy it via the Windows Phone Power Tools http://wptools.codeplex.com/
The 2nd version doesn't work on my Ativ: it gives the same error given when G. blocked it.
I re-deployed the 1st. :good:
Edit: the NoInterop_P2 runs properly.
@Topogigi @djadry When I packaged P2 of the InteropUnlock version, I accidentally used the wrong "Youtube.ViewModel.dll". I just updated the OP with the correct version. You should be good to go now
Hey there guys Hope to have a great day .
I made my first Custom ROM for Nokia Lumia 920 (RM-821) . this ROM contains the latest 10586 build I couldn't remember the minor OS version !
This ROM as I said the first custom ROM that I made and maybe it has some problems that I maybe don't know so please send me feedbacks here to work on it.
What is new in this ROM :
-The latest build of W10M
-Pre-Installed of the apps you need (Word, Excel, and etc.)
-The Microsoft Lumia 950XL Ringtones
How to install :
OK, first of all download ROM Parts and extract it somewhere .
better to flash your phone or do a hard reset before flashing this ROM.
download WPInternals and unlock your phone's BootLoader and Enable the Mass Storage Mode.
in WPInternals go to the -> Platform -> Flash -> Flash Separate partition and select the MainOS partition witch is extracted from the rar file .
and then simply flash it
After flash It's recommended to do a hard reset and then setup your phone first login to your ROM and enjoy it.
If you had any problems with the steps take a look at this post :
http://forum.xda-developers.com/showpost.php?p=68440016&postcount=54
Thanks @minimog34
I am working to do some registry changes like Pre-Interop unlock and etcetera in next versions of this ROM but guys please let me know what you want
Important : It is my first ROM and it should be risky .
ROM Download Link : https://www.mediafire.com/folder/nd6yd9pzbld7v/DHT_L920 (3 Parts)
NGame
Dormant Hackers Team
Reserved
Thanks! With redstone coming these custom ROMs will be more and more useful for x20 users Perhaps it's a good idea to make a guide on how to make custom ROMs? I'd definitely be interested in that, I still have a 920 here for testing things out on
RedStoneFun said:
Thanks! With redstone coming these custom ROMs will be more and more useful for x20 users Perhaps it's a good idea to make a guide on how to make custom ROMs? I'd definitely be interested in that, I still have a 920 here for testing things out on
Click to expand...
Click to collapse
You need to know what changes you are free to do and witch files are editable.
you can't edit and modify whatever you want .
creating custom ROM is really easy but if you what are you doing.
You have to backup your MainOS Partition and then mount the bin file using OSFMount. then you can see conteent and you can edit it.
Hi! Please help me. I can't press button "Flash partions", nothing happens. i took unlock boot. In Flash mode wrote file is very big. I don't know what to do.
thanks for your work.
any chance of having a lumia 925 windows 10 rom? i'm on windows phone 8.1 and can't update anymore.
hamza87 said:
thanks for your work.
any chance of having a lumia 925 windows 10 rom? i'm on windows phone 8.1 and can't update anymore.
Click to expand...
Click to collapse
Did you install Windows 10 ROM? Can you help me?
Radik1 said:
Did you install Windows 10 ROM? Can you help me?
Click to expand...
Click to collapse
No I didn't. I'm stuck on 8.1 for the moment. I have a lumia 925.
If you have a lumia 920, you could install the rom provided in this thread using wpinternals.
http://www.wpinternals.net/
some videos to help:
https://www.youtube.com/watch?v=1dGDinlXMTo
https://www.youtube.com/watch?v=F9ZImDdpX9s
hamza87 said:
thanks for your work.
any chance of having a lumia 925 windows 10 rom? i'm on windows phone 8.1 and can't update anymore.
Click to expand...
Click to collapse
Yeah sure you can unlock your boot loader and enable mass storage mode and then use regedit to change Phone Manufacturer .
Also you can help me to create your phones ROM
Radik1 said:
Hi! Please help me. I can't press button "Flash partions", nothing happens. i took unlock boot. In Flash mode wrote file is very big. I don't know what to do.
Click to expand...
Click to collapse
Really sorry for my late. you can see that WPInternals show you why your flash separate partition won't be activated, so let me know what's your error
hamza87 said:
thanks for your work.
any chance of having a lumia 925 windows 10 rom? i'm on windows phone 8.1 and can't update anymore.
Click to expand...
Click to collapse
ngame said:
Really sorry for my late. you can see that WPInternals show you why your flash separate partition won't be activated, so let me know what's your error
Click to expand...
Click to collapse
No problem. So, what I did? After Successful Unlock bootloader I switch to Mass Storage. Then My laptop find new disk with Main OS. I think it's good. Then I choose your Main OS, and tap "Flash partitions". (as picture). Many clicks don't help. Nothing... Install Windows 10 it's important for me.
Radik1 said:
No problem. So, what I did? After Successful Unlock bootloader I switch to Mass Storage. Then My laptop find new disk with Main OS. I think it's good. Then I choose your Main OS, and tap "Flash partitions". (as picture). Many clicks don't help. Nothing... Install Windows 10 it's important for me.
Click to expand...
Click to collapse
same issue here,
pressing flash does nothing in mass storage mode,
Radik1 said:
No problem. So, what I did? After Successful Unlock bootloader I switch to Mass Storage. Then My laptop find new disk with Main OS. I think it's good. Then I choose your Main OS, and tap "Flash partitions". (as picture). Many clicks don't help. Nothing... Install Windows 10 it's important for me.
Click to expand...
Click to collapse
mmmalas said:
same issue here,
pressing flash does nothing in mass storage mode,
Click to expand...
Click to collapse
hm, Why you guys switch to mass storage mode ?
boot phone in Normal or Flashing mode and after that your phone should be detected .
ngame said:
hm, Why you guys switch to mass storage mode ?
boot phone in Normal or Flashing mode and after that your phone should be detected .
Click to expand...
Click to collapse
when switching to flashing mode, it says that the size of the parition is too big for 'main OS'
I am coming from windows 8.1 image
mmmalas said:
when switching to flashing mode, it says that the size of the parition is too big for 'main OS'
I am coming from windows 8.1 image
Click to expand...
Click to collapse
I see this problem too. The size of the parition is too big for 'main OS'
Flash Partitions nothing happens with only Main OS selected
hi,
I have downloaded all three parts of Main OS and extracted to a separate folder.
Lumia 920 with 8.1 at present
have unlocked the boot loader via wpinternals
Now as per your instructions, I have connected the mobile and changed mode to Flash mode and in Platform -> Flash -> Flash separate partitions, selected only the main OS and guided it to the select the extracted (downloaded) file of yours. If only this file is selected and clicked Flash Partition button, nothing happens
If I choose the EFIESP file and Data file which I have taken backup from my phone and then select "Flash Partition" it says
Flash Failed!
Size of partitions 'MainOS' and 'Data' together are too big.
Hence can you extract the Data file of your mobile and share it, so that we can try to flash with both the files together. Even Wpinternal also describe that "Remember that the MainOS partition and Data partition are tied together, so you need to flash both partitions together".
ngame said:
Yeah sure you can unlock your boot loader and enable mass storage mode and then use regedit to change Phone Manufacturer .
Also you can help me to create your phones ROM
Click to expand...
Click to collapse
Quote:
Originally Posted by hamza87
thanks for your work.
any chance of having a lumia 925 windows 10 rom? i'm on windows phone 8.1 and can't update anymore.
Yeah sure you can unlock your boot loader and enable mass storage mode and then use regedit to change Phone Manufacturer .
Also you can help me to create your phones ROM
Yes I want do it cause the insider are no longer working for us and we have to take control about our own devices.
I have one L925 too and need help, and waiting for updates in this room like you sayd.
I want to try install it but I need your help give instructions about how to do !
You can give me the edits to change on regedit ?
suhail_ssr said:
hi,
I have downloaded all three parts of Main OS and extracted to a separate folder.
Lumia 920 with 8.1 at present
have unlocked the boot loader via wpinternals
Now as per your instructions, I have connected the mobile and changed mode to Flash mode and in Platform -> Flash -> Flash separate partitions, selected only the main OS and guided it to the select the extracted (downloaded) file of yours. If only this file is selected and clicked Flash Partition button, nothing happens
If I choose the EFIESP file and Data file which I have taken backup from my phone and then select "Flash Partition" it says
Flash Failed!
Size of partitions 'MainOS' and 'Data' together are too big.
Hence can you extract the Data file of your mobile and share it, so that we can try to flash with both the files together. Even Wpinternal also describe that "Remember that the MainOS partition and Data partition are tied together, so you need to flash both partitions together".
Click to expand...
Click to collapse
Thanks bro I will share EFIESP partition in a little while
Guys EFIESP is now available on mediafire take a look if it solve your problems
really sorry about late in answering you guys, my laptop HDD ran into a bad sector and it made my laptop useless but now it's fine again
ngame said:
Hey there guys Hope to have a great day .
I made my first Custom ROM for Nokia Lumia 920 (RM-821) . this ROM contains the latest 10586 build I couldn't remember the minor OS version !
This ROM as I said the first custom ROM that I made and maybe it has some problems that I maybe don't know so please send me feedbacks here to work on it.
What is new in this ROM :
-The latest build of W10M
-Pre-Installed of the apps you need (Word, Excel, and etc.)
-The Microsoft Lumia 950XL Ringtones
How to install :
OK, first of all download ROM Parts and extract it somewhere .
better to flash your phone or do a hard reset before flashing this ROM.
download WPInternals and unlock your phone's BootLoader and Enable the Mass Storage Mode.
in WPInternals go to the -> Platform -> Flash -> Flash Separate partition and select the MainOS partition witch is extracted from the rar file .
and then simply flash it
After flash It's recommended to do a hard reset and then setup your phone first login to your ROM and enjoy it.
I am working to do some registry changes like Pre-Interop unlock and etcetera in next versions of this ROM but guys please let me know what you want
Important : It is my first ROM and it should be risky .
ROM Download Link : https://www.mediafire.com/folder/nd6yd9pzbld7v/DHT_L920 (3 Parts)
NGame
Dormant Hackers Team
Click to expand...
Click to collapse
Hi Ali tell me how or what to do on mass storage of my Lumia 925 to upgrade to windows 10 mobile.
r_x4 said:
Hi Ali tell me how or what to do on mass storage of my Lumia 925 to upgrade to windows 10 mobile.
Click to expand...
Click to collapse
Connect your phone into the Mass Storage Mode to your PC.
open Regedit.exe on your pc and click on HKEY_LOCAL_MACHINE
from File Menu click on Load Hive and then path this file on your phone:
Windows\System32\Config\System
then it asks you for a name, name for example 123 or blabla
after that you have 123 or blabla sub key in HKLM navigate to that and Platform-->DeviceTargetingInfo
to see what you have to change here see this : http://forum.xda-developers.com/win...windows-mobile-10-redstone-rs1-build-t3319375
after changing values again mark 123 sub key and from file menu click on unload hive .
after unloading reboot phone and get insider builds .(This hack could be apply on any Windows Phone with 1 GB of RAM)
vcREG is a registry editor for lumia windows phones that has SYSTEM level access to the registry. the tool also has the ability to unlock all app capabilities for third party apps(interop unlock), and give SYSTEM level access to most of the filesystem through MTP.
new in version 1.7: thanks to @gus33000 for pointing out some registry values set for the interop unlock that may cause versions of rs1+ to break compatibility with WP8 apps. this has been fixed. For interop unlock, i suggest you use @gus33000 Interop Tools as his tool is more likely to have better support for changes in the future, as i am too bogged down with other projects.
thanks to @Wack0Distractor for sharing the idea and the acer service that makes this unlock for the X50 series phones possible. also thanks to @ngame for providing the test devices and the many hours of debugging, and @djamol for the main reason any of these unlocks are possible.
Instructions for X50 series phones like the 550,950/XL
ndtk_acer_services.zip uploaded below contains acer.service.acersystemservice.spkg, NdtkSvc.dll, and newndtksvc.dll.
1.Go to settings and turn on developer mode.
2a. For APPX version, download vcregUWP_1.7+dependencies.zip,unzip, install dependencies, then install the vcreg appx
2b. For XAP version, Sideload vcREG_1_7.xap using
WP8 xap deployer
C:\Program Files (x86)\Microsoft SDKs\Windows Phone\v8.0\Tools\XAP Deployment\Xapdeploy.exe
or
WP Power Tools
https://wptools.codeplex.com/
3.Go to the app bar, then choose x50 series unlock. You will receive an error about the acer service not running. That's ok for now. Click step 1 and it will tell you to install the acer system service and copy some files. To install the acer system service, use iutool [rs and newer builds,this version is essential,old versions will probably not work] (can be found here. thanks @Wack0Distractor ).
run this command as administrator
iutool -v -p "path to the file acer.service.acersystemservice.spkg"
if you receive error 0x80070490, disconnect your phone from usb, go to control panel on your pc, devices and printers, find your windows phone and remove device. reconnect the usb to your phone,and after it reinstalls the drivers automatically, run iutool command above again.
if you receive error 0x8024a110, your phone should reboot to the gears UI in a minute. if not, run the command again. if it still doesnt auto reboot, manually reboot your phone. It should reboot into the gears UI, then back into the OS. if it still fails and doest show gears, give you phone a rest for 5-10 minutes and retry(usually needed after a new rom flash).
4.When you're back in the phone OS, copy newndtksvc.dll and ndtksvc.dll to your documents folder on your phone through USB
5.Go to the app bar, then choose x50 series unlock. You should no longer receive the error about the acer service. Now click step 2 and follow the rest of the instructions from the app.
6.If you've taken the silent extras/advanced+info update, or updated that app manually, be sure to choose the option "Restore NDTK 950/XL" in the "x50 series unlock" page and reboot to regain access to the elevated features. It basically means if it suddenly stops working, apply this setting.
Instructions for older devices
1.Go to settings and turn on developer mode.
2a. For APPX version, download vcregUWP_1.7+dependencies.zip,unzip, install dependencies, then install the vcreg appx
2b. For XAP version, Sideload vcREG_1_7.xap using
WP8 xap deployer
C:\Program Files (x86)\Microsoft SDKs\Windows Phone\v8.0\Tools\XAP Deployment\Xapdeploy.exe
or
WP Power Tools
https://wptools.codeplex.com/
3.Go to the app bar, then choose classic unlock
3.If you've taken the silent extras+info update, or updated that app manually, be sure to choose the option "Restore NDTK" in the "classic unlock" page and reboot to regain access to the elevated features. It basically means if it suddenly stops working, apply this setting.
@vcfan thanks for mention
Not bad to add this that Our New hack for X50 series tested on both RS1 and TH2 (10586.107 to 14393.67) and these OS Versions are tested and supported Thanks for you and @djamol's hard work and other guys who helped in this hack .
Also here is a video that show you I added work with gloves on my 950XL to my phone and it work and etc.
http://www.aparat.com/v/HoCbk
Sorry for my bad English
Guys Do not TRY Full FILESYSTEM ACCESS ON X50 Series .
If you want to Change your X50/XL device font please try this app :
http://forum.xda-developers.com/showpost.php?p=68465197&postcount=46
Universal Interop Unlock is Coming :
http://forum.xda-developers.com/showpost.php?p=68467581&postcount=56
Wow, wow, wow! Great news! Thank you guys, @vcfan and @djamol, and @ngame and all guys who worked on this hack! xda rulez!
Awesome job! Any chance we can get some documentation on the methods?
G.moe said:
Awesome job! Any chance we can get some documentation on the methods?
Click to expand...
Click to collapse
@G.moe, what kind of documentation are you looking for? Have you tried to press large gray buttons saying "CLICK TO SHOW CONTENT" at @vcfan post? :laugh:
Or you are looking for the source code and hack method concept? Use reflector or any other .net disasms to get the app's sources
Thanks works fine.
I have trying MTP and now 950 XL charging only on PC.
Someone have original values in registry?
titi66200 said:
Thanks works fine.
I have trying MTP and now 950 XL charging only on PC.
Someone have original values in registry?
Click to expand...
Click to collapse
Guys in the video I recorded I tell do not try mtp hack it won't work also sftp doesn't work at least for me. If we can handle it at last we let you know.
Only concentrate on Interop and capability unlock and public registry hacks.
Also you can add work with gloves and double tap to your devices .
We are still working on many things to handle
i still try to get "gears" :crying:
tried few times...
dxdy said:
i still try to get "gears" :crying:
tried few times...
Click to expand...
Click to collapse
After Hard reset, Same for me
titi66200 said:
After Hard reset, Same for me
Click to expand...
Click to collapse
my 950XL have 14393.67 and also make HR two weeks ago...
SUPER GREAT !!!! WORKS LIKE A CHARM !!!
Many many many thanks..
works on Microsoft Lumia 950XL - RM-1085 -059X4X5
only MTP / full filesystem does not work but as i understand they are busy with it
vcfan said:
vcREG is a registry editor for lumia windows phones that has SYSTEM level access to the registry. the tool also has the ability to unlock all app capabilities for third party apps(interop unlock), and give SYSTEM level access to most of the filesystem through MTP.
thanks to @Wack0Distractor for sharing the idea and the acer service that makes this unlock for the X50 series phones possible. also thanks to @ngame for providing the test devices and the many hours of debugging, and @djamol for the main reason any of these unlocks are possible.
Instructions for X50 series phones like the 550,950/XL
1.Go to settings and turn on developer mode.
2.Sideload vcREG_1_6_W10.xap using
WP8 xap deployer
C:\Program Files (x86)\Microsoft SDKs\Windows Phone\v8.0\Tools\XAP Deployment\Xapdeploy.exe
or
WP Power Tools
https://wptools.codeplex.com/
3.Go to the app bar, then choose x50 series unlock. You will receive an error about the acer service not running. That's ok for now. Click step 1 and it will tell you to install the acer system service and copy some files. To install the acer system service, use iutool (can be found here. thanks @souma_rox).
run this command as administrator
iutool -v -p "path to the file acer.service.acersystemservice.spkg"
if you receive error 0x80070490, disconnect your phone from usb, go to control panel on your pc, devices and printers, find your windows phone and remove device. reconnect the usb to your phone,and after it reinstalls the drivers automatically, run iutool command above again.
if you receive error 0x8024a110, thats ok. your phone should reboot to the gears UI in a minute. if not, run the command again. if it still doesnt auto reboot, manually reboot your phone. It should reboot into the gears UI, then back into the OS. if it still fails, give you phone a rest for 5-10 minutes and retry(usually needed after a new rom flash).
4.When you're back in the phone OS, copy newndtksvc.dll and ndtksvc.dll to your documents folder on your phone through USB
5.Go to the app bar, then choose x50 series unlock. You should no longer receive the error about the acer service. Now click step 2 and follow the rest of the instructions from the app.
6.If you've taken the silent extras/advanced+info update, or updated that app manually, be sure to choose the option "Restore NDTK 950/XL" in the "x50 series unlock" page and reboot to regain access to the elevated features. It basically means if it suddenly stops working, apply this setting.
Instructions for older devices
1.Go to settings and turn on developer mode.
2.Sideload vcREG_1_6_W10.xap using
WP8 xap deployer
C:\Program Files (x86)\Microsoft SDKs\Windows Phone\v8.0\Tools\XAP Deployment\Xapdeploy.exe
or
WP Power Tools
https://wptools.codeplex.com/
3.Go to the app bar, then choose classic unlock
3.If you've taken the silent extras+info update, or updated that app manually, be sure to choose the option "Restore NDTK" in the "classic unlock" page and reboot to regain access to the elevated features. It basically means if it suddenly stops working, apply this setting.
Click to expand...
Click to collapse
dxdy said:
i still try to get "gears" :crying:
tried few times...
Click to expand...
Click to collapse
Double check this registry value using CustomPFD
HKLM\System\Platform\DeviceTargetingInfo
PhoneManufacturer
It must be in type (String) and it's value should be ACERINC to be able to deploy acer spkg.
If it's not you didn't do Step1 of VCreg correctly .
OK.
If you get 0x8024a110, you're probably on 14393 / anniversary update / Redstone1/whatever.
If so, you NEED to use iutool from the 14393 WDK. No ifs, no buts. Use that or you WILL get that error.
Here's a download of just the WP-tools (iutool, getdulogs, ffu creation etc etc) direct from MS: https://download.microsoft.com/down...5524A95/wdk/Installers/WP_CPTT_NT-x86-fre.msi
Mirrored it here just in case.
Works again for me.
I am stupid because "acer.service.acersystemservice.spkg" still installed after H.R.
titi66200 said:
Works again for me.
I am stupid because "acer.service.acersystemservice.spkg" still installed after H.R.
Click to expand...
Click to collapse
OH Yes guys . Good to say
After Hard reset you do not need to do many reboots because our ndtksvc is place in system32 (it didn't gone)
So you only need to go to x50 series page and check Live interop/cap unlock and apply it . that's it .
ngame said:
Double check this registry value using CustomPFD
HKLM\System\Platform\DeviceTargetingInfo
PhoneManufacturer
It must be in type (String) and it's value should be ACERINC to be able to deploy acer spkg.
If it's not you didn't do Step1 of VCreg correctly .
Click to expand...
Click to collapse
yes, ACERINC is there but still no luck...
---------- Post added at 02:11 PM ---------- Previous post was at 02:03 PM ----------
Wack0Distractor said:
OK.
If you get 0x8024a110, you're probably on 14393 / anniversary update / Redstone1/whatever.
If so, you NEED to use iutool from the 14393 WDK. No ifs, no buts. Use that or you WILL get that error.
Here's a download of just the WP-tools (iutool, getdulogs, ffu creation etc etc) direct from MS: https://download.microsoft.com/down...5524A95/wdk/Installers/WP_CPTT_NT-x86-fre.msi
Mirrored it here just in case.
Click to expand...
Click to collapse
installed and run iutool and now get gears!!!! thanks!!!
p.s.
interop is applied but.. still no use of AppDataManageTool or Adblock tool???
Great work!
Random question, probably a dumb one, but does this work on the M8FW? Or is it dependent on a x50 device exploit? Cause maybe I'm reading this wrong but it seems kinda universal
Thanks A lot!!!!
@dxdy
"Adblock tool" use "Nokia.SilentInstaller.Runtime" who seems not working on x50.
AlvinPhilemon said:
Great work!
Random question, probably a dumb one, but does this work on the M8FW? Or is it dependent on a x50 device exploit? Cause maybe I'm reading this wrong but it seems kinda universal
Click to expand...
Click to collapse
It's not intended for non-Microsoft/Nokia devices. NdtkSvc.dll is Nokia/Microsoft specific.....