Hi xda Community,
i got a big problem on my s6 edge. Thought, i was able to flash my phone from stock 6.01 to http://forum.xda-developers.com/galaxy-s6-edge/development/rom-carhdrom-1-t3111519.....it still works, but after a few days, my phone gets more lags and i was more disappointed ´bout that than the bloatware battery drain from stock rom. So...that´s the point. Tried to flash to stock 6.01, but it fails...... from now on, the only 2things i can do are to boot in download mode and twrp 3.02.....think, i don´t have any partitions installed .....
Tried a stock rom with dbt(without brabding) - vd2(vodafone) - dtm(t-mobile) nothing works.....
flash with odin says:
<ID:0/006> Added!!
<ID:0/006> Odin engine v(ID:3.1101)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> SingleDownload.
<ID:0/006> boot.img
<ID:0/006> NAND Write Start!!
<ID:0/006> cache.img
<ID:0/006> cm.bin
<ID:0/006> FAIL!
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/006> Removed!!
or....with other branded stock rom
NAND Write Start failed
My phone shows up the following words on the left of the screen( in download mode)
Odin Mode
Product Name: SM-G925F
Current Binary: Custom
System Status: Custom
Reactivation Lock: OFF
Secure Download: Enabled
Knoq Warrantay VOID: 1 (0x0500) (Ja, Garantie ist futsch)
RP SWREV: B:4 K:2 S:2
after the failed flash, i got this message an my phone´s screen
[CM] SW REV. CHECK FAIL. Device: 4, Binary 3
After that, my twrp mode is not working then, phone can´t shutdown and shows allways the message:
An error has occured while updating the device software.
Use the Emergency recovery function in the Smart Switch PC software.
I don´t know what to do....can i repair my phone by myself? or is it bricked for all time? :crying: :crying:
Please gimme a big help to get me through these hard days......
Use Smart Switch. It has firmware recovery function. Just fill in phone model and SN.
Sent from my SM-G925F
AlvarinGT3 said:
Hi xda Community,
i got a big problem on my s6 edge. Thought, i was able to flash my phone from stock 6.01 to http://forum.xda-developers.com/galaxy-s6-edge/development/rom-carhdrom-1-t3111519.....it still works, but after a few days, my phone gets more lags and i was more disappointed ´bout that than the bloatware battery drain from stock rom. So...that´s the point. Tried to flash to stock 6.01, but it fails...... from now on, the only 2things i can do are to boot in download mode and twrp 3.02.....think, i don´t have any partitions installed .....
Tried a stock rom with dbt(without brabding) - vd2(vodafone) - dtm(t-mobile) nothing works.....
flash with odin says:
<ID:0/006> Added!!
<ID:0/006> Odin engine v(ID:3.1101)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> SingleDownload.
<ID:0/006> boot.img
<ID:0/006> NAND Write Start!!
<ID:0/006> cache.img
<ID:0/006> cm.bin
<ID:0/006> FAIL!
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/006> Removed!!
or....with other branded stock rom
NAND Write Start failed
My phone shows up the following words on the left of the screen( in download mode)
Odin Mode
Product Name: SM-G925F
Current Binary: Custom
System Status: Custom
Reactivation Lock: OFF
Secure Download: Enabled
Knoq Warrantay VOID: 1 (0x0500) (Ja, Garantie ist futsch)
RP SWREV: B:4 K:2 S:2
after the failed flash, i got this message an my phone´s screen
[CM] SW REV. CHECK FAIL. Device: 4, Binary 3
After that, my twrp mode is not working then, phone can´t shutdown and shows allways the message:
An error has occured while updating the device software.
Use the Emergency recovery function in the Smart Switch PC software.
I don´t know what to do....can i repair my phone by myself? or is it bricked for all time? :crying: :crying:
Please gimme a big help to get me through these hard days......
Click to expand...
Click to collapse
Flashing stock firmware should resolve this. First thing if you can boot into twrp clear cache partition, wipe data/ factory reset. Then try flashing stock firmware.
As for the sw rev check fail. It because the device is rooted. Carhd rom is pre rooted that's why you get that message.
Try again flashing stock firmware after the above steps. Let me know of any errors
Ok....SmartSwitch didn't work,so tryin' to Download another Stock Rom with samfirm, vd2.... Hidden.img Fail, but cleared.......everythings fine now.....so, thx for your help......
Related
A few months ago, I got a (Verizon) Samsung Galaxy S4 (it was "free" with contract). I successfully rooted it not long after.
Just a couple weeks ago, an update was released through the verizon network, so blindly I decided to use the update, only to find out afterwards that it removed my root. I tried the same method I used before to root it, only to find people saying that the newest OTA (Over The Air) update made rooting impossible.
After a fair amount of searching, I found a method which supposedly would work (http://forum.xda-developers.com/show....php?t=2487142). I used the method, however it did not work, and my phone was stuck in download mode.
After previous reading, I learned that the only way to manually exit download mode was to take out the battery. Though the root attempt had failed, it was obvious that something had occurred, so I was hesitant to use the brute force method of exiting download mode. However, without knowing an alternative, I removed the battery.
Now, whenever I try to turn on my phone, I merely get the message "Firmware update has encountered an issue. Please select recovery mode in Kies and try again."
If it helps, the text displayed in the upper corner with this message is:
ODIN MODE
PRODUCT NAME: SCH-I545
CURRENT BINARY: SAMSUNG OFFICIAL
SYSTEM STATUS: CUSTOM
KNOX KERNEL LOCK: 0x0
KNOX WARRANTY VOID: 0x0
CSB-CONFIG-LSB: 0x30
WRITE PROTECTION: Enabled
eMMC BURST MODE enabled
I have tried firmware upgrade and initialization in Kies3, but an error message is shown saying "SCH-I545 does not support initialization", When I tried Kies2, it just told me that the device was not responding.
I am still able to enter download mode.
When I try to flash an os using odin, I get these results:
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sbl1.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl2.mbn
<ID:0/003> sbl3.mbn
<ID:0/003> rpm.mbn
<ID:0/003> aboot.mbn
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
And in the corner of my phone screen, a red message appears which says:
START [224,1440]
SW REV. CHECK FAIL : fused : 6 , Binary : 5
If there is any more information you would need, please let me know.
Oddity3 said:
A few months ago, I got a (Verizon) Samsung Galaxy S4 (it was "free" with contract). I successfully rooted it not long after.
Just a couple weeks ago, an update was released through the verizon network, so blindly I decided to use the update, only to find out afterwards that it removed my root. I tried the same method I used before to root it, only to find people saying that the newest OTA (Over The Air) update made rooting impossible.
After a fair amount of searching, I found a method which supposedly would work (http://forum.xda-developers.com/show....php?t=2487142). I used the method, however it did not work, and my phone was stuck in download mode.
After previous reading, I learned that the only way to manually exit download mode was to take out the battery. Though the root attempt had failed, it was obvious that something had occurred, so I was hesitant to use the brute force method of exiting download mode. However, without knowing an alternative, I removed the battery.
Now, whenever I try to turn on my phone, I merely get the message "Firmware update has encountered an issue. Please select recovery mode in Kies and try again."
If it helps, the text displayed in the upper corner with this message is:
ODIN MODE
PRODUCT NAME: SCH-I545
CURRENT BINARY: SAMSUNG OFFICIAL
SYSTEM STATUS: CUSTOM
KNOX KERNEL LOCK: 0x0
KNOX WARRANTY VOID: 0x0
CSB-CONFIG-LSB: 0x30
WRITE PROTECTION: Enabled
eMMC BURST MODE enabled
I have tried firmware upgrade and initialization in Kies3, but an error message is shown saying "SCH-I545 does not support initialization", When I tried Kies2, it just told me that the device was not responding.
I am still able to enter download mode.
When I try to flash an os using odin, I get these results:
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sbl1.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl2.mbn
<ID:0/003> sbl3.mbn
<ID:0/003> rpm.mbn
<ID:0/003> aboot.mbn
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
And in the corner of my phone screen, a red message appears which says:
START [224,1440]
SW REV. CHECK FAIL : fused : 6 , Binary : 5
If there is any more information you would need, please let me know.
Click to expand...
Click to collapse
Try to flash the NC5 odin.
joshuabg said:
Try to flash the NC5 odin.
Click to expand...
Click to collapse
I can enter download mode, but am unable to enter recovery mode. I just gives me the "Firmware upgrade encountered an issue" message again.
Nevermind
Oddity3 said:
I can enter download mode, but am unable to enter recovery mode. I just gives me the "Firmware upgrade encountered an issue" message again.
Click to expand...
Click to collapse
Some people have reported getting past that screen with volume up/volume down. Worth a try.
Basically, you have NC5 system and NC5 bootloader. You tried to flash a factory stock MK2 from the looks of it and failed. What you need to do is to go to Surge1223's thread with info on flashing back to MK2 here and try to re-flash using his process.
Today I got verizon samsung s4 (new, from Woot). It came with Lollipop, but Kies suggested an update, so I tried it. The update failed and now I'm stuck on "Software Update Failed"
I couldn't find the "Verizon Software Repair Assistant" download.
I cant get it to boot to recovery. It just goes to "Software Update Failed" or ODIN
So I started trying to flash it with ODIN. Read a lot of threads (enough to realize that this is a deep mess and get quite confused) and tried half a dozen of ROMS, and a PIT, but all fail with these message in the phone:
"SW REV. CHECK FAIL : fused 8, Binary :6"
(of course, the Binary change with the firmware)
Does it means that I need a newer firmware? What else can I do?
Thanks,
Jorge
I don't have much info about what was on the phone before. The problem got me unprepared, since I expected the Kies update to be trivial.
But this is what I get on the "Software Update Failed" screen:
ODIN MODE
PRODUCT NAME: SCH-I545
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Official
REACTIVATION LOCK: Off
CSB-CONFIG-USB: 0x30
SECURE DOWNLOAD: ENABLE
WRITE PROTECTION: Enable
eMMC BURST MODE: Enable
Please, help me fix my phone.
Have you tried flashing the firmware which corresponds to Fuse: 8? (Lollipop OC1 or OF1)
Tried with OC1 and got "Fused : 8 binary : 7"
I'm downloading OF1 from here: http://forum.xda-developers.com/galaxy-s4-verizon/general/of1-stock-tar-t3216417
(taking forever)
While downloading the previously mentioned OF1 (20 min left now...),
I tried with the I545_Downgrade_tC1.tar mentioned here:
http://forum.xda-developers.com/gal...-to-update-to-i545of1-5-0-1-keeproot-t3182544
I got a good start flashing, but then I got:
<ID:0/003> Odin engine v(ID:3.1100)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> boot.img
<ID:0/003> NAND Write Start!!
<ID:0/003> recovery.img
<ID:0/003> NON-HLOS.bin
<ID:0/003> modem.bin
<ID:0/003> system.img.ext4
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
and on the phone:
SYS. REV. CHECK FAIL: Refer 2 > Binary 1
SOLVED!
I had some problems flashing OF1, but then I used my notebook instead my PC, and worked!
For the record, I used the OF1 from here:
http://forum.xda-developers.com/galaxy-s4-verizon/general/of1-stock-tar-t3216417
Thanks!!
Jorge
So long story short I wanted to recover deleted photos, found a program that required my phone to be rooted, rooted my phone, couldn't find the photos, tried to "unroot" my phone and now I believe my phone is bricked.
I have searched far and wide for a good 5 hours on here, and google.
When I try to flash anything with odin, I get this:
<ID:0/004> Odin engine v(ID:3.1005)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> recovery.img
<ID:0/004> NAND Write Start!!
<ID:0/004> FAIL!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
My phone is stuck on the samsung logo screen with "this is not a seandroid enforcing" and "frp lock on". I've tried to flash recovery, I get "Custom binary(recovery) blocked by frp lock", same goes with trying to flash firmware. Kies and smart switch do not detect my phone, i've tried several usb ports, blah blah, I'm pretty sure it's not working due to the frp lock.
I can only access the download page and the other recovery page with the 6 or so options, I've factory reset my phone, and wiped the cache. Trying to apply an update from ADB says it's disabled, along with external storage and update from cache.
The info on the top of my download page:
ODIN MODE
PRODUCT NAME: SM-G925P
CURRENT BINARY: CUSTOM
SYSTEM STATUS: CUSTOM
FRP LOCK: ON
SECURE DOWNLOAD: ENABLED
KNOX WARRANTY VOID: 1
RP SWREV: B:3 K:2 S:2
I am stumped, hopefully all is not lost.
If no one knows, is there any possible way I can turn FRP lock off? I cannot access my phone to do so, so hopefully there is a way to turn it off
No one can help? I've been stuck without a phone for 2 days, please help
Hello there,
I have an old Samsung Galaxy Note 10.1 (GT-N8010 Wifi only), which I've rooted successfully, only to find it stuck in a bootloop after some time. Whole thing happened a while ago and after many hours spent trying to fix this thing, I've surrendered and haven't touched the device since. It's been a year and now I decided to give it a shot once again, but there is no way I could remember what I've already done to it. Its current state is as follows:
1. boots only into download mode, which says:
ODIN MODE
PRODUCT NAME: GT-N8010
CURRENT BINARY: CUSTOM
SYSTEM STATUS: CUSTOM
RP SWREV: A2
2. after trying to flash it with stock ROM (found here: don't know how to post link because of new account restriction, maybe via pm) Odin fails with this message:
<ID:0/004> Odin engine v(ID:3.1203)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> sboot.bin
<ID:0/004> FAIL!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
This tablet is close to worthless to me, hence I'm willing to try everything you guys suggest (except taking it to service point).
Thank you all for help
Hi there,
The Samsung S7 Edge of a friend got stuck @boot. I have tried to reset and wipe. But that does not solve the problem.
So now i am trying to put on the latest official firmware from Samfw, Smammobile and/or Frija but Odin 3.14 fails.
I think the phone got stuck in an OTA update.
Please help
Here are more details.
S7 Edge SM-G935FD in the Netherlands (PHN), the G935F version should be working as well, its an exynos chipset with dual sim.
In download mode it says on top left:
Product Name: SM-G935F
Current Binary: Samsung Official
System Status: Official
FRP Lock is ON (i cannot go to devevlopper mode to change that)
Secure Donwload: Enabled
Warranty Void: 0
AP: SWREV: B:8 K:6 S:7
I followed all kind of guides on XDA
Get the right Odin 3.14
Get the right Firmware. Samfw.com_SM-G935F_PHN_G935FXXU8ETI2
Using Default Odin Settings
I have a connection to the phone.
This is the ODIN log:
<ID:0/004> Added!!
<ID:0/004> Odin engine v(ID:3.1401)..
<ID:0/004> File analysis..
<ID:0/004> Total Binary size: 4045 M
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> NAND Write Start!!
<ID:0/004> SingleDownload.
<ID:0/004> sboot.bin
<ID:0/004> param.bin
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
What am i missing?
Is the device locked somehow? Or is it a hw failure?
Dekay99