Related
Hi,
I do not have enough posts to post in the cyanogenmod nightlies thread to get a definitive answer, hence why this subforum. I guess my question may be rom independent anyway.
I 'upgraded' from an M release of cyanogenmod to a nightly and buggered my phone. I was forced to flash the stock firmware and then reflash the nightly to fix everything. Except my camera shows a black screen (behind the onscreen focus and options) and force closes nearly all the time. I thought it was just the nightly, but 2 months and 20+ new nightlies later, I still have the issue. In the nightles dev thread, people say the camera is fine. I know the hardware is fine, because 1 in 40 tries the camera randomly works.
I tried a factory wipe, which I now know just wipes user data. So In CWM, under 'mounts and storage' I formatted everything I could and did another factory reset, cache etc. No fix.
I guess this issue is with the rom itself, if the camera is force closing? So I'll have to use Odin or such to flash a stock rom again and flash another cyanogenmod version? But I want to check this is correct before continuing, and how I can completely wipe any trace of the current rom before flashing the stock and another nightly - so I don't get this issue again.
Thanks
So I finally found the issue, after battling with heimdall on ubuntu 14.04 for hours. Its a hardware problem.
I'm just going to leave my experience here in case someone else has the same issue, since anything to do with all the issue I am about to describe don't seem to be documented anywhere on the web clearly.
Firstly, I battled with heimdall 1.3.2 to recognise my phone on ubuntu. I kept getting;
Code:
ERROR: Failed to receive response!
After a number of threads talking about installing usblibx drivers I found one about which libs to install from terminal;
Code:
sudo apt-get install libXXXX
Code:
libusb-ocaml
libdevice-usb-perl
libhpmud0 (not sure if it's essential)
libusb-0.1-4
libusb-1.0-0
libusb-1.0-0-dev
libusb-dev
libusbprog-dev
libusb++-0.1-4c2
libusb++-dev
libusbtc08-1
libusbmuxd-dev
libusbprog0
libusbmuxd1
I installed all but couldn't find libusbmuxd1, restarted anyway, to the same error. I purged heimdall 1.3.2 and instead installed it from the Ubuntu software centre, which using
Code:
sudo apt-cache policy heimdall
showed that I had version 1.4 installed. Then I managed to find
Code:
libusbx-1.0.14_1.0.14-1_amd64.deb
floating somewhere on the internet, which finally installed the proper libusb stuff and allowed heimdall to continue without the error message.
I made a .pit file from my phone. I recommend this first. After hours searching for a stock rom (samsung has removed most of its firmware downloads? and asked links to be removed on other sites!?) came across this site
(I can't post links as a new user) - google [TUTORIAL] Flashing i9000, i9100 or i9300 with Heimdall
Which explains how to flash using heimdall. After a successful flash, my phone didn't get farther than the boot animation. I booted into stock recovery with vol up-home-power to factory reset, but noticed a dead droid and red writting. Rather than continue, I wanted to fix this, so I followed the tutorial again, but this time checked repartition under the pit path, and hoped for the best. The phone stalled at the boot anim again, but this time in recovery, all was good.
I did a data wipe / factory reset, cache wipe etc, but nothing. So I stuck the stock rom zip onto the micro sd and installed it from recovery, factory reset, and rebooted. (which is odd, having to install the rom from recovery - because doesn't that kinda defeat the point of using the same image on heimdall in the first place?!?)
The phone booted! So after all that, (Having data/factory reset, wiped the cache, (wiped the dalvik cache when i had CWM before and formatted all I could in mounts and storage) flashed the stock ROM AND repartitioned the phone) i thought that would eliminate any software issues. I thought the camera would work.
Nope.
As usual, the front camera worked, but the back, now, after a pause would give the samsung error:
Code:
unknown error by errorcallback
Now, after googling this (Cyanogenmod gave a different error with no related answers on google) and being annoyed at my time lost, I took the tongue and cheek advice from some random forum commenter, to tap the camera hard.
It worked.
Apparently, the entire time the camera was suffering from a hardware issue. Something about a 'sticky shutter'. Anyways, i'm going to leave the stock ROM and take it into a shop to get it fixed. Just leaving this trail of breadcrumbs in the hope it helps someone else.
Perhaps this could be marked as 'solved'.
Same problem
FINALLY; first time I see the problem I have (I'm not feeling good about you having the problem, btw). I've had this problem for a lot of time and I haven't had found it elsewhere.
I have the same issue, but without the error that says "unknown error by errorcallback". Mine just says "Unfortunately, Camera has stopped working". I didn't really understand if it had appeared to you after you did all that, or if it was from the beginning... anyways, just "tapping hard" the camera will make it work? And, did it fix it permanently?
Sorry for any typo.
Edit: I've "tapped" the camera really hard, and no signs of anything. Any advice? (I've done practically everything you have done but flashing the stock rom)
JCNouel said:
FINALLY; first time I see the problem I have (I'm not feeling good about you having the problem, btw). I've had this problem for a lot of time and I haven't had found it elsewhere.
I have the same issue, but without the error that says "unknown error by errorcallback". Mine just says "Unfortunately, Camera has stopped working". I didn't really understand if it had appeared to you after you did all that, or if it was from the beginning... anyways, just "tapping hard" the camera will make it work? And, did it fix it permanently?
Sorry for any typo.
Edit: I've "tapped" the camera really hard, and no signs of anything. Any advice? (I've done practically everything you have done but flashing the stock rom)
Click to expand...
Click to collapse
Try flashing stock rom and see if this fixes your problem.
gsstudios said:
Try flashing stock rom and see if this fixes your problem.
Click to expand...
Click to collapse
It fixed it, but then I flashed back the AICP ROM, which is KK, and it malfunctioned again. I'm going to try with a JB Custom ROM.
Update: I flashed a JB Custom Rom (Fusion Rom) and it's working good so far.
After flashing the latest version( pa_i9300-5.1-20150528.zip) in recovery, 'Reboot System' reboots to recovery itself. Weird! So I flashed the earlier version(pa_i9300-5.1-20150520.zip) and it rebooted to system and it works. Now I get the OTA update in 'Paranoid OTA' app for the latest version that gave me problems. If I install,
1. Will there be any issues with reboot or any other related issues?
2. Should I reinstall installed apps after update?
Thanks
Not sure if related but I installed pa_i9300-5.1-20150520.zip some time ago on my i9300, everything has been working nicely. Then came the 28th update and another one earlier this month... but installing those updates just resulted in a crash after installing (as in the boot screen looping). Now my system just popped up with an 20150619 update so I thought to try again, but again it download and installs just to loop the boot screen. This time thought I afterwards decided to re-install superSU and my boeffla kernel, that seemingly did something as the phone booted and update. Now maybe this is something one have to do for each update for it to work? I'd love to know for the future as I'm no expert on this, though if you have something similar maybe that's what is required.
Organizer21 said:
Not sure if related but I installed pa_i9300-5.1-20150520.zip some time ago on my i9300, everything has been working nicely. Then came the 28th update and another one earlier this month... but installing those updates just resulted in a crash after installing (as in the boot screen looping). Now my system just popped up with an 20150619 update so I thought to try again, but again it download and installs just to loop the boot screen. This time thought I afterwards decided to re-install superSU and my boeffla kernel, that seemingly did something as the phone booted and update. Now maybe this is something one have to do for each update for it to work? I'd love to know for the future as I'm no expert on this, though if you have something similar maybe that's what is required.
Click to expand...
Click to collapse
I think flashing the Kernel as you did after the dirty flash will help. But the there is no stable Kernel available for CM12.1, even the Boeffla you are using is in the alpha stage, no support yet! So how is the battery life and stability with Boeffla Kernel?
Here's a Stockish ROM for your N915P. This ROM has Knox, Sprint ItsOn, and secure storage removed. Nothing else was done to this ROM. I'm new to the Note Edge so I may upload patches to remove any other traces of Knox or ItsOn or optimizations I happen to find while making my own ROM.
Prereq: OG1 Baseband. Download it below.
Modified stock kernel (BeastMode Stock): Kernel modified to allow root by disabling "Root Restriction in defconfig"
Download
MD5: 75bd507e3b4296a128f1c0c48fd2359c
Version 1.1: Enabled many TCP Congestion options via defconfig. Added init.d ability via ramdisk.
Odex:
Download
MD5: 59d544ef6a4bc12d969f4efd9577d36d
DeOdex DEBLOATED:
Download
MD5: 00b5246b9c2074e7ff04f6af2bad1ec2
OG1 Baseband:
Download
MD5: 3bc88209d60117fb573e0f5a2e50f4e9
Patches and fixes:
None yet.
[size=+3]DeOdex note:[/size]
The first boot time for this DeOdex ROM is very long. Approximately 5-8 minutes. Your phone will get hot as the splash screen remains on the yellow Sprint boot animation. I recommend keeping your phone in a cool environment while this is happening. The heat, if not properly checked, can make boot times even longer as the system throttles speed in order to deal with the heat. This doesn't happen on the Odex version.
[size=+3]Install instructions:[/size]
-Are you currently on the OC8 bootloader and would like to stay on it?
--Simply flash the baseband with Odin, and the ROM.
-Are you on the update from OTA or flashed the OG1 TAR?
--Flash kernel only.
-Are you one of the unlucky ones to take the OTA and hose your system trying to root and are now on another ROM?
--Flash ROM only.
-Are you on any build after OC8 but not the current OG1?
--Flash the baseband and ROM. Bootloader is optional and not available in this thread as of yet.
Wiping is only necessary if you are coming from a different base, such as AOSP/CM. If you are coming from a touchwiz ROM, wiping isn't needed, but won't hurt.
Changelog:
9/5/15: Initial Release.
Kernel source code: Download
Thanks, will flash tomorrow.
Thank you so much freeza!! Patiently waiting for the deodexed version and for the baseband.
Added modified stock kernel v1.1 and baseband.
Freeza if I'm on 5.0.1 still just flashing the baseband may give me better service ? Technically...
Downloading now still waiting on the deodex will play with the stock to see how it is thanks
Ok, flashed rom, kernel, and modem. Took a while to boot but all is running well at the moment. Thanks for supporting our device!!
DeOdex uploading....
What What!!! By far the best developer on a Samsung!! Thank you so much for your hard work brother!! Real Talk, i still have your rom on my Note 3! It runs flawlessly!! XD
Get your DeOdex on, guys! ;D
Thanks so much for this!!! I love the separate edge screen and have no reason to "upgrade" to the Note 5
Thank you freeza NICE WORK WITH THE KERNEL
When I saw you had been requested to come help this phone achieve root I knew great things were going to come to those who waited. I've had other devices where you were there to help gain root and again you came through. I purposely didn't take the OG1 update because I knew in time this device wasn't going to be ignored. IMO it is the best NOTE device out there and it will be mine until they make a NOTE EDGE 2 (With SD card and removable battery). Thank you for the quick response and the hard work you do to make this happen.
Cant get either one of them to boot. Both the odex and the deodex wont boot, they both flash fine and then after the phone reboots it stays on the yellow sprint screen Maybe for up to a minute then reboots and it cycles that way. Never boots. I've tried not wiping/Factory restarting as well as wiping/Factory resetting. Have also tried formatting through TWRP to no avail. Have also tried flashing the kernel and wiping caches after flashing but Nothing is working. Have also flashed the baseband.
Im currently on OF6 if that should matter.
Edit: md5 Sums have also match up. Have downloaded both from my phone and a pc to no avail.
Edit 2: tried both TWRP 2.8.6.0 and 2.8.7.0. Also tried clockworkmod recovery and that didn't work either.
I had success but it took some time. I downloaded the deodexed debloated rom, the kernel, and the baseband. I had a method to how I wanted to do this and here is how i got there.
I was running OC8 rom rooted.
1. I odened the baseband tar file and rebooted. But unfortunately it bootlooped on the initial splash screen (note edge) so
2. I ran TWRP recovery and installed the kernel file. Rebooted phone and it ran fine. I looked at the settings about phone and saw that the baseband and the rom all said OG1 but i had not installed the rom yet. So i figure it was a trick to get the baseband to install. So
3. I went back into recovery. Wiped dalvik cache and regular cache and installed the new rom. It installed fine and i waited the length of time for the initial boot up. But this time as it was "Android is starting" it rebooted and got stuck on the sprint splash screen and kept randomally vibrating. Having the ability to remove the battery
4. Rebooted back into recovery, wiped everything including internal storage, and reinstalled the deodexed rom. It installed fine and went to the initial startup screen where it tries to initialize and it rebooted one time, back to the initialize screen but continued without a hitch.
I currently am running OG1 5.1.1. With root.
At times during setting up the phone it would randomally vibrate for no reason...short bursts...but it hasn't yet again rebooted, restarted, or crashed. It is faster from what i see. Probably because there are almost no google apps installed. I've had to install chrome, youtube, and maps. But all seems fine. My signal and speeds are the same so the baseband didn't do much to change that. But so far so good.
---------- Post added at 11:30 AM ---------- Previous post was at 11:27 AM ----------
I did try to install over my odexed OC8 with this new rom but because there is so much different about the files that are installed IMO formatting the phone was the only way to get this to work.
---------- Post added at 12:16 PM ---------- Previous post was at 11:30 AM ----------
One final thing just in case it isn't known: when you wipe everything in TWRP, excluding external storage, you have to restart the recovery before trying to install a rom. It will say you have no OS installed, but you are restarting the recovery not booting a rom, so that's fine, but you do lose root status when wiping. So the next screen gives you the ability to gain root again, but you have to restart TWRP to do that. In the past i tried to figure out why installing after wiping didn't work, and 99% of the time it was because of that. I also don't like installing new roms over older roms (even if they are the same base (touchwiz to touchwiz)) because i feel I would spend more time troubleshooting why something isn't working instead of just starting over. I find less hassle doing it this way.
I odin baseband .tar file, than reboot it to recovery, and flash kernal and odex room at the same time, saw some red messages when kernel was flashing, than odex rom was next but it was successful when it was done. (I did not know if kernel falsh ok so i reflash kernel again) reboot to system and after the android system updated all its ok. No problems so far.
Oh and i inclided the supersu at the same time i flash kernel, odex rom and supersu.
1. Odin baseband tar file.
2. Flash kernel, odex rom and supersu.
3. Re-flash kernel.
4. Reboot to system and profit.
(Maybe i did un necessary steps, but its working. )
Was running great but have been experiencing Google account and store issues. Tried odex and deodex versions with similar results. Anyone else having issues?
Johnny Halo III said:
Was running great but have been experiencing Google account and store issues. Tried odex and deodex versions with similar results. Anyone else having issues?
Click to expand...
Click to collapse
Just starting to have random freezing. And not able to select my apps froms the edge screen, i can only scroll through it. Will remove all the app shorcuts and re-add tham again.
**update 1.
I removed all shorcuts from the edge screen and added them back, all work but some i have to select them a few times before they open.
Maybe i have to reflash, reset, clean and wipe.
**update 2.
Clean install of odex rom, and kernal 1.1.
No more lagg but the edge screen does not work properly. Not able to select and open some of the favorite app shorcuts.
**update 3.
Factory reset, cleaned and wype, odin sprint lollipop update (uf something), downloaded OG1 update. Installed all apps from scratch. And the edge screen does not work. I can scroll, side to side, up and down, but when i select an app it does not open it.
** update (last one)
Foud the code to test the phone hardware.
*#0*# on dial screen. Tested all and it came out good. But i notice that some how the edge screen its not as whide as it used to be ( like its more to the right of the phone) so where i use to touch to select an app its now more to the right emd of the edge, thats why i was able to scroll but not select the app.
Its all good now. Now second round of flashing.
Will give it another try at the room.
Thanks Freeza and sorry about the problems i had and hopefully did not cause anyone from not trying this great work pr yours.
I left all the problems i had so tje next person trying this room does not get discureged from trying. But allways fallow direction.
:thumbup:
** last update
After setting and resetting, flashing and un-flashing, rooting and un-rooting. I can finally wrote that all is good. Running latest lollipop 5.1.1 and freeza's new 1.1 kernel, I can reprt that all is smooth as butter.
Thanks for the hard work.
Thank you so much for your hard work Freeza! So glad I'm finally running 5.1.1 on this beast :]
The ROM is working pretty well, but I have noticed that every now and then, the phone will be rather laggy. Turning the screen off and on again seems to fix the issue, making me think that the processor is being throttled while the screen is off (good) but isn't being sped back up when the screen is turned on..sometimes.
It's not a huge deal, but I was wondering if anyone was experiencing the same thing.
No issues here.
Starting on OG1 had to flash bootloader, kernel, deodex rom and supersu to make it stick. Two days now and battery, signal and speed seem improved.
Thanks freeza!
Hi,
I am running RR 5.8.3, v. from 23-04-17.
I was forced to set fluencetype for the past few flashes to null or something, because otherwise I did not have sound during calls.
Right now the call quality is unbearably bad. It was not THAT bad on older ROMs, before I had to disable this fluence-thingie.
I want to upgrade the ROM, but what else am I supposed to improve the voice quality? I could not find a decent source.
Factory reset -> VoLTE patch -> RR ROM -> GAPPS?
Anything else? Some people wrote "updade your firmware" - how am I supposed to interpret it? Install MIUI Rom? So, like flash it from TWRP and replace it with RR 2 minutes later? I am alergic to MIUI.
This topic kind of explains it, but links are down and content might be outdated:
https://forum.xda-developers.com/redmi-note-3/how-to/android-n-permanent-volte-fix-10000-t3541922
Up
Up.
Right now I am stuck on a bootloop with rom's logo. I can access TWRP and flash stuff just fine, but I cannot load the system. Restoring from backup has failed.
I have installed 7.7.7 firmware - https://www.androidfilehost.com/?fid=673368273298969813
and booted to the system. It did not recognize my PIN and locked my card. Unlocked it with PUK on another device, but still the same.
Flashed newest RR with GAPPS and reflashed the firmware. Bootlooping begun.
Tried different ROMs, tried a different firmware - https://www.androidfilehost.com/?fid=673368273298969055
What should be the "next step"?
I was able to fix it, but man this was my last flash of this device. My next step was to brick the device, had to start from stratch after that. Never had so many different issues... I will rot on current ROM till Pixel 2 arrives.
As tittle says, I have been in XDA for a while, never created an account cause I have always encountered responses to all my problems there. But not this time. I have created an account just to ask you people if someone knows (or had) this problem.
I have been getting touchscreen problems since a while (I dont know if it was caused by a custom kernel I changed months ago, or by touchscreen needing a replacement). Then the problem with WebView happend, but after trying to fix it by OTA, reinstalling WebView, clearing cache of google apps and few other things, apps kept closing randomly, and with the touchscreen failing, it was a real pain, so I downloaded a few roms and saved all my data, then went to TWRP. I updated it to 3.5.2_10-0-beryllium before anything, and flashed vendor, firmware and ROM GLOBAL_V12.0.3.0.QEJMIXM_cf3fccffce_10.0. Here begins the brick. I cannot pass the first boot, in any of the roms I tried. In MIUI, the logo of starting stay indefinitly (not the poco one, the MIUI one). I tried pa-quartz-5-beryllium-20200924, also stays infinitly in the green ball logo moving. After that, I tried lineage-18.1-20210410-nightly-beryllium-signed, with the same result, Infinite starting moving blue logo (more than 8h and still didnt boot). I tried clean installs and dirty installs. The worst part is that my PC only recognizes my F1 on recovery, Fastboot don't seems to be working (I was going to try flashing via fastboot). And here I am, after 6h of trying different installs, flashing the Disable Force Encryptation, flashing stock firmware and stock rom, stock firmware and custom roms, flashing vendor, not flashing vendor, etc... Im sick.
Thanks in advance to anyone who try to help me.
EDIT: I missed that i was having random reboots too, not only touchscreen fails.
iJaviXR said:
As tittle says, I have been in XDA for a while, never created an account cause I have always encountered responses to all my problems there. But not this time. I have created an account just to ask you people if someone knows (or had) this problem.
I have been getting touchscreen problems since a while (I dont know if it was caused by a custom kernel I changed months ago, or by touchscreen needing a replacement). Then the problem with WebView happend, but after trying to fix it by OTA, reinstalling WebView, clearing cache of google apps and few other things, apps kept closing randomly, and with the touchscreen failing, it was a real pain, so I downloaded a few roms and saved all my data, then went to TWRP. I updated it to 3.5.2_10-0-beryllium before anything, and flashed vendor, firmware and ROM GLOBAL_V12.0.3.0.QEJMIXM_cf3fccffce_10.0. Here begins the brick. I cannot pass the first boot, in any of the roms I tried. In MIUI, the logo of starting stay indefinitly (not the poco one, the MIUI one). I tried pa-quartz-5-beryllium-20200924, also stays infinitly in the green ball logo moving. After that, I tried lineage-18.1-20210410-nightly-beryllium-signed, with the same result, Infinite starting moving blue logo (more than 8h and still didnt boot). I tried clean installs and dirty installs. The worst part is that my PC only recognizes my F1 on recovery, Fastboot don't seems to be working (I was going to try flashing via fastboot). And here I am, after 6h of trying different installs, flashing the Disable Force Encryptation, flashing stock firmware and stock rom, stock firmware and custom roms, flashing vendor, not flashing vendor, etc... Im sick.
Thanks in advance to anyone who try to help me.
EDIT: I missed that i was having random reboots too, not only touchscreen fails.
Click to expand...
Click to collapse
Check my POCO F1 Ultimate Collection & Guides. Try to Clean Install Pixel Experience for example, according my guide (u need to format data also). Let me know how it goes.
Tried Android 10 and 11 Pixel Experience, tried with stock and NG Kernels. Still stays forever in the first load of the SO.
Just got the properties file from XiaomiADBFastbootTools. Maybe someone can see something wrong on it.