Problem with battery indicator. - Xiaomi Mi Pad Questions & Answers

Hi,
I tried to root my Mipad 2 and after reboot there was a bootloop. So I reinstalled rom and tablet is working now but battery indicator shows 42% only. In TWRP I see real value. I tried to install other roms, the same. Now I use AOSP, the same problem. What else can I do to fix it ? System is rooted now but I don't know what tools can help. If you have any suggestion, please, let me know.

Same here
Its the kernel problem

Related

Phone is Crashing

Hello.
I have a problem with my S II... Out of nowhere it started crashing. It boots normally, but once it loaded, it crashes immediately. The crash is actually a system freeze, then it shuts down. The battery is fully charged, but the phone was burning while it was charging, not the battery though. So basically I start the phone, it freezes, then it shuts down.
Don't know if it's the battery or the firmware... I have stock firmware.
Thank you in advance.
UPDATE:
The phone is still burning, at the back top, camera area. The battery discharges very quickly now I see.
I remember using the flash before it happened. I used it to a point where it started buzzing and discharged the battery to 5%. I put it immediately to charge, but, now it's like in a vegetable state...
Still don't know if it's the firmware's fault or the battery. I don't want to rewrite the firmware, the battery I could change... But I'm thinking the camera or it's flash is broken, freezing the phone and draining it's power... Is that even possible? What to do?
Thank you.
UPDATE 2:
Ok, I found the problem, the mainboard was faulty and I had to replace it.
But now even though it seems to work even better, it has something else......... The USB port isn't working. The circuit board with the microphone, usb, etc. is the one I had before, didn't change that. So it should work perfectly, but it's not. When I plug the charger, it takes a few good seconds to see the status "charging", and when removed it's the same. When I connect the phone to the PC's USB port, it doesn't recognize the phone. What the hell? I enabled the USB Debugging on the phone and still nothing... The battery is charging though, but very slow. Damn, this phone is torturing me!!
Please someone help me with this other issue... ((
Thank you!
UPDATE 3:
I managed to fix my phone. Changed the mainboard, changed the USB board, installed firmware and it worked.
Thank you all for all your help!
Check the voltage during charging via Battery Doctor. It is due to your battery. Try changing battery
syedbilal093 said:
Check the voltage during charging via Battery Doctor. It is due to your battery. Try changing battery
Click to expand...
Click to collapse
How do I do that? The phone freezes the moment it loads the system. I wrote an update in the original post. Thanks for trying to help.
So, anyone has any idea?
First replace your battery. Try to replace charger. It is your main board maybe thats why your S2 restarts itself. It is critical. If it does not solve your issue ... it is your kernel. Lots of peoples are complaining about kernel bad behaviour ... they are also not rooted. So try to root it if the battery doesnt solve your issue. Also try to have a hardware checkup by a technician ...! Hope it helps
syedbilal093 said:
First replace your battery. Try to replace charger. It is your main board maybe thats why your S2 restarts itself. It is critical. If it does not solve your issue ... it is your kernel. Lots of peoples are complaining about kernel bad behaviour ... they are also not rooted. So try to root it if the battery doesnt solve your issue. Also try to have a hardware checkup by a technician ...! Hope it helps
Click to expand...
Click to collapse
So I consulted a technician and the problem was the mainboard. I had to replace it... Now it works like a charm, or so it seemed at first. Now something else is ****ed up.
I wrote another update in the original post, please read it...
Thank you for all your help.
@lucian there are charging pins and computer connecting pics on the main board which lets your smartphone to communicate with pcand charge. These pins have some prints for reading. So these prints are damaged according to my info.!. Repair those prints and let us know.!
@Lucian Andries I have the same problem of heating at the part of camera .. Dont worry i dont think its because the problem of flash or your camera .. Only because your battery gets heated up and leads to heating up your device . So i had to change my modem to control the heating im using KH3 now which doesnt heat up very often .. but i do have some heating when its over charged !!
@GreenArrow_I9100: What is KH3?
@syedbilal093: Ok, I tried that to, I changed the USB/Microphone board too. That didn't work either. The problem this time was still the mainboard, it had a faulty stock Firmware installed on it. I installed CyanogenMod 11 SNAPSHOT 12, and the problem was solved.
Thanks guys for trying to help.
Lucian Andries said:
@GreenArrow_I9100: What is KH3?
@syedbilal093: Ok, I tried that to, I changed the USB/Microphone board too. That didn't work either. The problem this time was still the mainboard, it had a faulty stock Firmware installed on it. I installed CyanogenMod 11 SNAPSHOT 12, and the problem was solved.
Thanks guys for trying to help.
Click to expand...
Click to collapse
KH3 is the modem type ..
You can download it from here http://forum.xda-developers.com/attachment.php?attachmentid=1066735&d=1337266991
And then flash it from odin but upload file in PHONE/MODEM instead of PDA in odin It did help me with heating problem !!!
For now even im running cm11 m12 snapshot over dorimanx and encountered no problems so far . I get a battery life for around 4-5 hours on screen wifi on .. And no heating problems !
GreenArrow_I9100 said:
KH3 is the modem type ..
You can download it from here http://forum.xda-developers.com/attachment.php?attachmentid=1066735&d=1337266991
And then flash it from odin but upload file in PHONE/MODEM instead of PDA in odin It did help me with heating problem !!!
For now even im running cm11 m12 snapshot over dorimanx and encountered no problems so far . I get a battery life for around 4-5 hours on screen wifi on .. And no heating problems !
Click to expand...
Click to collapse
I installed that modem too. Didn't check the modem I had before. Hope will help.
On my cm11 m12 I have some problems. Applications just "stop working" out of the sudden. As there is no thread for SNAPSHOT versions, I'm asking you if you have this issue. Is this due to kernel? Should I change the kernel? I have the cm11 kernel...
Thanks!
Lucian Andries said:
I installed that modem too. Didn't check the modem I had before. Hope will help.
On my cm11 m12 I have some problems. Applications just "stop working" out of the sudden. As there is no thread for SNAPSHOT versions, I'm asking you if you have this issue. Is this due to kernel? Should I change the kernel? I have the cm11 kernel...
Thanks!
Click to expand...
Click to collapse
Generally applications stop working if you alter the procedure of flashing the kernel while you flash the rom
I prefer this order
1. Install dorimanx kernel
2. check for kitkat compatible recovery
3. Full wipe data factory reset, cache partition, dalvik cache, Mounts and storage --> Format/system
4. Install Rom cm11 snapshot
5. Install Gapps(Used PA gapps)
6. Reboot !!
Anyway many say that kernel can be flashed between rom and gapps.
But so far i never had any problem of application stopped working !! So try this out !! Hope this solves your problem
Great to hear that @lucian
GreenArrow_I9100 said:
Generally applications stop working if you alter the procedure of flashing the kernel while you flash the rom
I prefer this order
1. Install dorimanx kernel
2. Install kitkat compatible recovery
3. Full wipe data factory reset, cache partition, dalvik cache, Mounts and storage --> Format/system
4. Install Rom cm11 snapshot
5. Install Gapps(Used PA gapps)
6. Reboot !!
Anyway many say that kernel can be flashed between rom and gapps.
But so far i never had any problem of application stopped working !! So try this out !! Hope this solves your problem
Click to expand...
Click to collapse
But is the Dorimanx kernel better than CyanogenMod's kernel?
@Lucian Andries Doesnt really matter the kernel here if you follow the correct order of flashing them .. I hv tested rom over both kernels and it was smooth with no problems So what you choose is upto you but i personally like Dorimanx
Both kernels are good though
GreenArrow_I9100 said:
@Lucian Andries Doesnt really matter the kernel here if you follow the correct order of flashing them .. I hv tested rom over both kernels and it was smooth with no problems So what you choose is upto you but i personally like Dorimanx
Both kernels are good though
Click to expand...
Click to collapse
I don't know. CyanogenMod may be smooth and all, but the GPS isn't working even with KH3 modem, unless set it to network/wi-fi/gps. And the camera also doesn't perform right. The colours are desaturated and it doesn't focus right. I think I'll roll back to official stock 4.1.2 for this device...
Could you tell me which is the best stock 4.1.2? I'm from Romania, and here we have this version "I9100XWLSS_I9100OXFLS3_COA_4.1.2". But they didn't put any effort into it...
Thank you.
Lucian Andries said:
I don't know. CyanogenMod may be smooth and all, but the GPS isn't working even with KH3 modem, unless set it to network/wi-fi/gps. And the camera also doesn't perform right. The colours are desaturated and it doesn't focus right. I think I'll roll back to official stock 4.1.2 for this device...
Could you tell me which is the best stock 4.1.2? I'm from Romania, and here we have this version "I9100XWLSS_I9100OXFLS3_COA_4.1.2". But they didn't put any effort into it...
Thank you.
Click to expand...
Click to collapse
All stocks are the same only difference is the location and language as far as i know get your required zip from samfirmware.com as per your location and flash it through odin. It should work !!
But gps is working fine in cm11 for me .. Dont know why its not working in your device mate !!
GreenArrow_I9100 said:
All stocks are the same only difference is the location and language as far as i know get your required zip from samfirmware.com as per your location and flash it through odin. It should work !!
But gps is working fine in cm11 for me .. Dont know why its not working in your device mate !!
Click to expand...
Click to collapse
I don't know about that. I don't think it's just the location and language. For the language, all the location firmwares have all the languages included. But, not all the location firmwares are the same. I'm sure some of them have more work put into them than others. That's why some of them are buggy, having boot loops, very high battery consumption and slow response in apps and menus. Get my point? That's why I asked which country has the best official rom.
@Lucianandries, i came here after a long time. Some issues. Exams preparation, you know . I want to ask if your other problems are solved or not.? As for "application stopped" error. It is usually normal in Cyanogenmod. I also sometimes face this and that's why i don't use CM. Try to use "Official" builds. They are good.!

Battery shows negative value

Hello guys,
I've recently bought a Redmi Note 3 Pro (3GB RAM) and the first time I booted it up it showed that it has -2% battery life. Since this seemed strange I tried to charge for several hours, but no change was noticed. I then tried with a battery calibration app, tried factory reset and restarting the phone, but nothing helped. I am also not able to go in recovery mode for hard reset as it states that there is no charge ...
The strange thing is that the phone is working for now and I am using for a second day with still the same bug. This leads me to believe that the problem is most likely caused by incorrect battery stats saved on the phone, but I am not sure. I am also not willing to root it or flash it since it is brand new and I might lost the warranty.
Can you guys suggested me a solution for this or the problem is not easily recoverable?
Thank you for the time and answers!
I have the exact same problem, tried resetting everything, I suspect it is a hardware problem.
awedxz said:
Hello guys,
I've recently bought a Redmi Note 3 Pro (3GB RAM) and the first time I booted it up it showed that it has -2% battery life. Since this seemed strange I tried to charge for several hours, but no change was noticed. I then tried with a battery calibration app, tried factory reset and restarting the phone, but nothing helped. I am also not able to go in recovery mode for hard reset as it states that there is no charge ...
The strange thing is that the phone is working for now and I am using for a second day with still the same bug. This leads me to believe that the problem is most likely caused by incorrect battery stats saved on the phone, but I am not sure. I am also not willing to root it or flash it since it is brand new and I might lost the warranty.
Can you guys suggested me a solution for this or the problem is not easily recoverable?
Thank you for the time and answers!
Click to expand...
Click to collapse
Try updating, I had this issue with custom ROM's something certain boot images have this bug.
I flashed a new boot image and bug was gone but had no wifi reverted back to latest global stock via MiFlash.
If you have TWRP try the ROM here https://xiaomi.eu/community/threads/6-7-7-11.32639/ it seems ok.
Did anyone find a fix for this issue. I have the same problem. Battery percentage shows negative 2% and I can't get into recovery because of that. When I press Power and Volume + It shows the battery icon in red and won't let me into recovery. I have the Redmi Note 3 Pro Snapdragon version.
I tried flashing a couple of ROMs via MiFlash with no positive results.
Maybe a bit late, but the "camera fix" in this Thread fixed my "-2%"-Battery
http://forum.xda-developers.com/red...cyanogenmod-13-0-xiaomi-redmi-note-3-t3350656
Just flash with TWRP.
5t4m said:
Maybe a bit late, but the "camera fix" in this Thread fixed my "-2%"-Battery
http://forum.xda-developers.com/red...cyanogenmod-13-0-xiaomi-redmi-note-3-t3350656
Just flash with TWRP.
Click to expand...
Click to collapse
What rom are you using?
EkiFox said:
The camera fix works only with Santosh's CM13, not with other CM/AOSP roms
the new kernel Radon V1.8 by Umang96 does not fix the battery problem
Click to expand...
Click to collapse
The Radon V1.8 Kernel actually causes this bug on MIUI based roms, so don't flash the kernel.
Radon Version 1.9 will resolve the battery bug on MIUI and other roms.
Talking about cm/aosp I tried almost all combination kernel/rom.
No success except for this particular cm with camera patch.
Same problem with battery, showing -2% but phone is working... Plz provide solution asap
If u run MIUI, just download FASTBOOT ROM, restart phone to FASTBOOT MODE and flash ROM using this tool. But if u run custom ROM just flash custom kernel (like RADON).
5t4m said:
Maybe a bit late, but the "camera fix" in this Thread fixed my "-2%"-Battery
http://forum.xda-developers.com/red...cyanogenmod-13-0-xiaomi-redmi-note-3-t3350656
Just flash with TWRP.
Click to expand...
Click to collapse
Fixed the -2% Bug on latest CM13-Snapshot for me!
You Sir are awesome
flashed the latest global firmwareware(not developer one) solved my issue, also now my phone updates OTA.
Use only the official rom. custom that sellers flash usually is a junk just with additional options for menu's language!
Same problem with battery, showing -2% but phone is working... Plz provide solution asap what to do. .. mobile automatically switch off too
Geeta_ghai said:
Same problem with battery, showing -2% but phone is working... Plz provide solution asap what to do. .. mobile automatically switch off too
Click to expand...
Click to collapse
Flash the latest miui ROM in edl mode using miflash. That is the answer.
No
No that is not the answer it's a hardware issue short circuit in motherboard
induna said:
Flash the latest miui ROM in edl mode using miflash. That is the answer.
Click to expand...
Click to collapse
androidnandroid said:
No that is not the answer it's a hardware issue short circuit in motherboard
Click to expand...
Click to collapse
Hmm, well flashing an official ROM in edl mode has fixed this problem for many people, including myself. So it would seem that in most cases at least it IS a software issue that can be fixed by flashing.
My phone came from Banggood and a vendor ROM that wouldn't even support my FP reader, Goodix, and which booted up with the -2% battery bug out of the box. Flashing the official global stable ROM, 8.0.2.0 at that time, fixed all of the issues.
Hmmm may be sir but that doesn't seem to fix mine although mine is from xiaomi only and the problem came after using 6 month suddenly without any reason one morning
Ok guys there are 2 solutions to this problem one is drain your battery and don't charge it for 2 3 days drain it like he'll coz after switch off still some juice is left you have to drain completely and other rapid method is open your redmi note 3 and disconnect battery cable and reconnect it... The problem is not software its hardware where battery reading stuck at minimal which is - 2 ... Thinking minus two hours coz at zero still some battery left for edl and fastboot mode time and alarm... Fixed my redmi note 3 hope it will help you.. Coz tried all method format... 10 times flash all roms through fastboot mode Coz updater mode won't work coz of low battery reading... Enjoy guys
I am having a same issue with redmi note 3 SD version. Tried everything Global BETA ROM, STABLE ROMs but didnt solved my issue. Showing -2% bettery in every ROM which i have flashed.
I am facing a similar problem where my phone showed -2 as battery level but my phone is not booting at all without any charger attached. and even when the chargr is connected it boots upt the Mi Logo and then displays an empty battery which wont charge even when tried for hours. Please help
razy111 said:
I am facing a similar problem where my phone showed -2 as battery level but my phone is not booting at all without any charger attached. and even when the chargr is connected it boots upt the Mi Logo and then displays an empty battery which wont charge even when tried for hours. Please help
Click to expand...
Click to collapse
I had the exact same problem like this one on xiaomi redmi note 3 pro sd. I tried flashing fastboot miui 10 official but the problem still there. I also tried changing the usb charging port but still the same. I tried plug in the charger and hold power and + volume and it stuck at mi logo.
I want to know if anyone fix this?? Please help.

Deep Sleep Issues, event wakelocks 0-8

Hey everyone. redoing my thread now that we have tried alot of solutions, hopefully someone has a vague idea of what we can do to my phone lol.
So then, my phone (redmi note 3 snapdragon) refuses to go into deep sleep no matter what combination I've tried.
Tried Combos
1. RR+ radon and agni
2. Miui 8 stable and dev preview (7.1.5 and 8.1.1.0)+ stock, radon, and neon kernel (flashing using miflash with unlocked bootloader official)
3. Cm13 latest nightly+ radon, stock, and agni
4. Nitrogen os+ nagato kernel (current rom)
All combinations we're tried with clean installs (factory data, system,cache and internal storage)
Hardware methods tried
1. Physically disconnecting fingerprint sensor (goodix)
now then, with wakelock detector, we can see im troubled with a 99% awake time, along with 100,00's of event wakelocks over 6hours, now event wakelocks deal with the actual hardware of the phone from what i've seen, which makes little sense to me because the screenshot i am attaching was just over an entire night of not touching the phone. so why it has any activity is bizarre to me. so heres what we have tried so far on my previous thread.
Tried methods of fixing event wakelocks
1. Greenify, force doze, wakelock blocker and blocking everything in frustration. deep sleep battery saver.
2. physically deleting events one by one (going into dev/input/eventx (x being wakelocks 1-10) after deleting some my display eventually stopped working, most likely because i just deleted the event that controls the lcd i assume. rebooting fixed the problem and remade the events in their directory so no harm done.
3. removing zram usage figuring it was a thrashing problem (saw a thread in the hd desire of the same issue. didnt help sadly.
4. flashing modem in radon thread, ended up making my phones earpiece not work for calls and still had the wakelocks.
5. disabling gps, along with auto brightness and auto rotate
so then if anyone needs any other information just let me know, currently using an iPhone for the time being so im desperate lol. but still id rather fix and find the problem then go for returning the phone. better to solve a problem for future people in my shoes then just thrust it away is how i see it. also someone bug the strix and darkstrix about this maybe they know the solution. anyway thanks for reading and i hope we can fix my phone soon
^Update^ now using epic rom 7.1.12 from the xda thread, still got wakelocks on stock without any other apps.
I have same problem in all versions of stock MIUI Rom. I too tried all sorts of combination but the problem remains. Finally I'm using RR Rom 5.7.4 (20161113 build) + radon Kernel. My deep sleep problem have been solved (though not 100%). Now my phone looses very little battery in standby time like 1-2% over a night. Before RR Rom I tried many custom Rom but had same problem. If you have not tried the ROM (RR Remix 20161113) I've mentioned above give it a try. Best Of Luck.
Thanks rj I'll install and post logs after work. Fingers crossed that it fixes my problem.
use the rom android 6.0.1 with module powernap , u can fix it !!
http://repo.xposed.info/module/net.jzhang.powernap
Small update: testing stamina mod currently with xposed. ressurection remix will be next only because xposed seemed a bit easier lol
Well damn :/ tried RR rom and still nothing sadly, also powernap with RR didn't do anything as well. both were tried with radon and agni kernels
Then once try nexus rom i am getting good battery life in this rom too.
rjrulz007 said:
Then once try nexus rom i am getting good battery life in this rom too.
Click to expand...
Click to collapse
surer rj which one?
Having same problem.. Battery is draining very fast in idle mode.. Deep sleep is not working in any rom.. Something is keeping cpu awake.... If u find any solution then plz let me know bro.. Thanks
That happens to me when background data enabled . when i disable backround data through data usage settings , the battery backup gets better, but sure my social apps wont sync.
It seems the wakelock come from android system itself , go check logcat and you will get messages like "ANDR_PERF_RESOURCES FAILED TO APPLY PERFORMANCE" , the likes of "decided to move IRQ from cpu0 to cpu1" , and the likes of "FPC listener : waiting..." , thats all that i notice and thats happening every single milisecond on every MM roms i have tried so far....
Well when i used miui 7 LL global didnt get that much messages on logcat , but its LL ...
I guess the problem is related to source code , i dont know .
Did you try to disable fingerprint also? In many previous ROM this solved the issue.
D4xel said:
Did you try to disable fingerprint also? In many previous ROM this solved the issue.
Click to expand...
Click to collapse
yes sir still nothing
rohit4kk said:
Having same problem.. Battery is draining very fast in idle mode.. Deep sleep is not working in any rom.. Something is keeping cpu awake.... If u find any solution then plz let me know bro.. Thanks
Click to expand...
Click to collapse
hey dont worry man you'll be the first when we find an answer lol
Zaccary said:
Well damn :/ tried RR rom and still nothing sadly, also powernap with RR didn't do anything as well. both were tried with radon and agni kernels
Click to expand...
Click to collapse
Poor network signal also can cause this issue. My old carrier had crappy signal, once I switched, it increased my phone's battery since the new network has much better signal.
deltatux said:
Poor network signal also can cause this issue. My old carrier had crappy signal, once I switched, it increased my phone's battery since the new network has much better signal.
Click to expand...
Click to collapse
thanks for the tip but we are running on airplane mode only at this point just to make sure we don't have more things to worry about battery drain. i appreciate the information though ^_^
Mine kenzo, tried all miui version, always the same.
sbor-si said:
Mine kenzo, tried all miui version, always the same.
Click to expand...
Click to collapse
I'm not alone!!!
Hey hopefully we find an answer buddy
Yesterday I want to flash 7.3.2.0 xiaomi.eu version (clean install via twrp), but get bootloop. Than I flashed official global developer version (7.1.19) (fastboot via miflash, flash all), nothing better, except android system used 6%, android 39% and dex2oat 20%.
Can somebody try 7.3.2.0 version, from earlier posts is visible, that this version rocks, all later versions have issues.
sbor-si said:
Yesterday I want to flash 7.3.2.0 xiaomi.eu version (clean install via twrp), but get bootloop. Than I flashed official global developer version (7.1.19) (fastboot via miflash, flash all), nothing better, except android system used 6%, android 39% and dex2oat 20%.
Can somebody try 7.3.2.0 version, from earlier posts is visible, that this version rocks, all later versions have issues.
Click to expand...
Click to collapse
i believe last time i tried 7.3.2.0 it gave me constant reboots and lagged quite a bit. but i also heard it was the best for battery so i can try flashing through miflash again after work. im also going to be trying this rom here https://forum.xda-developers.com/re...nzo-lldlm18-1-3m866beta-real-factory-t3375250. since it uses edl mode instead of fastboot so hey maybe that will knock something lose?
Well, right now I'm trying to get it working - without luck. I can flash 7.3.2. with miflash via edl without troubles, phone started normaly, all seems good, until "No service" for gsm signal. Bad luck. I think that modem version from that old flash is not compatible with hardware.
But it looks so good - Android takes 20% and Android system 6%...

Galaxy S7 G930F mmc0_detect and bbd_wake_lock wakelocks - enormous battery drain

40$ Paypal for the person who finally helps me to solve my problem!
I have a very serious battery problem with my Galaxy S7 G930F.
Even at night when I do not use it and I turn on flight mode and energy saving mode it drains up to 10% battery per hour. When I go to bed with 60% sometimes the battery is completely discharged when I wake up in the morning.
I have had that issue for a long time now an I have already tried a lot to investigate what is causing the problem.
The first thing I tried was to completely wipe everything and reflash the official Nougat ROM. It did not help at all (I did not configure anything or install any apps! so the problem can not be caused by some app).
Then I tried both the SuperStock ROM and the Superman ROM for G930F - but the problem persistet. (I fully wiped everything in TWRP before flashing the new ROMS)
Using the App Wakelock Detector I found out that my phone is unable to go to deep sleep at all - and I also found out that the Kernel Waklocks mmc0_detect and bbd_wake_lock are causing this problem.
I have found out so far that the mmc0_detect problem can be caused by a faulty SD-Card - but I have not SD-Card installed!
The bbd_wake_lock comes from the broadcom sensorhub driver.
I have no idea what to do now, because I don't have better knwoledge to resolve the root cause of the problem.
Could it be a hardware probleme since the problem persists even with a clean install of a new ROM? I did not install any apps and the problem is already there.
Thanks for your help.
i.imgur.com/FfGOKMo.png
i.imgur.com/SEhPDeY.png
(sorry I can't post images yet)
I'm having the same problem too... I've also done the same steps that you did (factory reset, clean install superman rom, removed SD card, formatted SD card on the phone etc etc)... i'm starting to think that it's hardware problem....
the only difference I have with you is that my phone's a G930FD
Hi there....I'm running into the exact same issue. This is 100% Wifi related. If I turn off Wifi both these wake locks go away. I used better battery stats to track it.
I'm not sure what can be done to prevent it (other than turning off Wifi). Any ideas??
Thanks.

Mi pad wont charge red light.

Hi guys,
I was using Miui in mi pad 1 but it was really laggy IN VIDEOS and many apps including netflix wont even load in 4.4.4.
I moved to lineage 14.1 shield and apart from camera all were good.
i thought of upgrading to oreo and in middle i broke the device.
I went back to stock rom but i choose latest Chinese build 9.2.4.0 and use mi flash tool to boot it up. I was able to boot fine.
Again i went to custom rom dotos 2.5 and could see on locksreen showing phone charging slowly.
I kept for 3 hours and still same. I thought issue with the rom. WIPE EVERYTHING and again install lineage 15.1. It was able to boot fine but still no charging.
I kept my pad for hours to charge but still red light blinking, not booting up.
I removed the backpanel to remove battery (connector) and insert it again but still same.
I am not sure what to do now. If it will boot up i can go back to stock but it is not even booting to fastboot.
PLEASE HELP.
THANKS
Mont1jack said:
I removed the backpanel to remove battery (connector) and insert it again but still same.
Click to expand...
Click to collapse
Hello Is your problem fixed as I'm also experiencing the same
This also happened to me too in the past, my MiPad 2 is just in storage, still don't know how to fix it. Anyone here fixed this problem?

Categories

Resources