Hello,
I have probably bricked my Huawei Vision by rewriting boot image.
However, I can connect* it to PC and it sees my phone as "Huawei Handset" (same with Windows and Linux). But Windows misses its drivers (non-bricked phone worked); Linux seems to work. No OS can connect to it using default (downloaded) ADB, nor Fastboot, nor SoftwareUpdateTool.
Its PCI ID is 12d1:c002.
How could I reflash it? I would prefer the ways without disassembling the phone.
Thanks
----How to boot the phone, so you can connect it to PC:
1. turn off my phone completely (vol up + power for 10 seconds - release power for a seconds and repeat it once again)
2. prepare USB cable, so you can connect it in few seconds
3. hold vol down + power and after ~1s, connect USB cable (still hold vol down)
4. when Huawei logo appears, release both buttons - your phone is connected now
petoxxx said:
Hello,
I have probably bricked my Huawei Vision by rewriting boot image.
However, I can connect* it to PC and it sees my phone as "Huawei Handset" (same with Windows and Linux). But Windows misses its drivers (non-bricked phone worked); Linux seems to work. No OS can connect to it using default (downloaded) ADB, nor Fastboot, nor SoftwareUpdateTool.
Its PCI ID is 12d1:c002.
How could I reflash it? I would prefer the ways without disassembling the phone.
Thanks
----How to boot the phone, so you can connect it to PC:
1. turn off my phone completely (vol up + power for 10 seconds - release power for a seconds and repeat it once again)
2. prepare USB cable, so you can connect it in few seconds
3. hold vol down + power and after ~1s, connect USB cable (still hold vol down)
4. when Huawei logo appears, release both buttons - your phone is connected now
Click to expand...
Click to collapse
mine is not working i think mine is bricked completly
bricked my mobile...Help!!!!
I had installed the latest rooted russian firmware and unknowingly installed the ICS..Now my device stuck at boot and while connecting with sutlr error(cannot identify device) occurs..What to do:crying:???
sivakarthick said:
I had installed the latest rooted russian firmware and unknowingly installed the ICS..Now my device stuck at boot and while connecting with sutlr error(cannot identify device) occurs..What to do:crying:???
Click to expand...
Click to collapse
The thread called 'Problem with huawei vision' still seems to be active. You may want to try asking your question over there.
Huawei (u8850) unbricked
I just wanted to relate my experiences in de-bricking this U8850 phone.
I installed 'Apps_2.6.35.7-perf+root+CWM_recovery 5.0.2.8' (firmware.nb0) using SUT to get CWM, and then installed Danile's 4.1.2
Good as far as it goes, but i could not for the life of me reproduce his kernel (my kernels are always unreliable), so after many days of playing, i decided to take the phone back to stock to see if i could reproduce the huawei stock kernel as a base to work on.
The problem was, how do you revert to stock; the phone was no longer recognised by SUT?
So I took a stock .nbo file and extracted the content (some java extractor found with google) in the hope that I could create a CWM flashable zip of the stock firmware.. a bit of research later, and i thought i had got the gist, put boot.img and system.img into a zip with a modified script file, and voila... a bricked phone.
At this point, i had CWM, but if the phone booted, it showed a flash of blue screen (I didn't know these ran windows ), and back to huawei logo. Also I think i had to dismantle to disconnect battery to run CWM, as it's not available just on the volume-up-power restart.
So then I did more research, and came across QPST, Qualcom's tools. It seemed this should know something about the files i had extracted. I could not correlate everything in the extracted fileset with what QPST seemed to expect, but the first challenge was to get QPST and the phone talking. using various drivers, QPST would sometimes see it, sometimes not, but nothing good seemed to be coming from it. I returned to trying to get SUT to work on my brick; again, with some drivers it would connect, but a flash always resulted in Error 4000 - DEVICE_NOT_CONFIGURED.
Then I read somewhere that someone had found a driver change made SUT work, so i investigated drivers more.
What I found was that if i ran up CWM, I got two Huawei devices in XP for which I could not find drivers.
The devices showed up as VID_12D1&PID_1022&MI_00 and VID_12D1&PID_1022&MI_01.
I took the Huawei USB drivers folder, and copied the qcser.inf then changed entries under [QcomSerialPort] to match my VID/PID values.
(the two that had matching MI_ values).
On driver update, I had a serial port, plus something I'd not seen before - a USB storage device which contained the phone's partitions!!!
This certainly seemed promising... so into SUT again, same error 4000...
So the I tried QPST; and yes, it could see the phone. Scared to do anything to brick it further, I thought, ok, try some memory diagnostics.
On running the 'Memory Debug' tool, as soon as I tried to get a list, QPST said 'this phones in diagnostic mode, it must be in download mode to do memory diagnostics', but even better 'Do you want to set it into download mode now?'!!!!!
Yeah! click the button, and I see a screen I've only seen once before (and i don't know why last time), black, with a line added every few seconds... which from all my reading I know is a good sign.
OK, then I closed all QPST apps, and ran SUT.
This time, the firmware flashed no problem. Was a bit worried as boot time is long (but it was effectively 'first ever' boot for the phone).
I hope this helps someone else with this or another Qualcom based phone.
Basic lesson is:
If you see Error 4000, it may be that the phone is in diagnostic mode rather than download mode.
If you don't have drivers, or don't have the right drivers, check you VID and PID, and try putting them into the .inf file
QPST may have a simple use after all... to force a phone into download mode when SUT fails.
how to turn off huawei u8850 completely
hey,could you please help me.i am stuck on huawei logo.how can i turn off the phone completely.i cant remove the battery obviously.the above trick isnot working.plz.help me
bikeshrt said:
hey,could you please help me.i am stuck on huawei logo.how can i turn off the phone completely.i cant remove the battery obviously.the above trick isnot working.plz.help me
Click to expand...
Click to collapse
it's actually not difficult to remove the battery...
but i read somewhere the 'volume-up + power for five seconds' will hard restart, but re-press power immediately will then turn it off (not tested myself; the back of mine is already off at the moment.)
Anyone here interested in developing a 3.x kernel? seems other phones with msm8255 have successfully got one...
u8850 power off
btsimonh said:
but i read somewhere the 'volume-up + power for five seconds' will hard restart, but re-press power immediately will then turn it off (not tested myself; the back of mine is already off at the moment.)
Click to expand...
Click to collapse
now i have tried it, and no success.
However, what i have found to work - if your non-boot is actually booting the kernel, but failing to initialise the phone, then you can still use adb with it... I ran adb shell, and then used 'poweroff' to power off my phone, which then meant i could boot into CWM recovery....
i HAVE THE SAME PROBLEME? PLEASE CAN U HELP ME TO SOLVE IT BY GIVING ME DETAILS.
it is working, thank you bro
btsimonh said:
I just wanted to relate my experiences in de-bricking this U8850 phone.
I installed 'Apps_2.6.35.7-perf+root+CWM_recovery 5.0.2.8' (firmware.nb0) using SUT to get CWM, and then installed Danile's 4.1.2
Good as far as it goes, but i could not for the life of me reproduce his kernel (my kernels are always unreliable), so after many days of playing, i decided to take the phone back to stock to see if i could reproduce the huawei stock kernel as a base to work on.
The problem was, how do you revert to stock; the phone was no longer recognised by SUT?
So I took a stock .nbo file and extracted the content (some java extractor found with google) in the hope that I could create a CWM flashable zip of the stock firmware.. a bit of research later, and i thought i had got the gist, put boot.img and system.img into a zip with a modified script file, and voila... a bricked phone.
At this point, i had CWM, but if the phone booted, it showed a flash of blue screen (I didn't know these ran windows ), and back to huawei logo. Also I think i had to dismantle to disconnect battery to run CWM, as it's not available just on the volume-up-power restart.
So then I did more research, and came across QPST, Qualcom's tools. It seemed this should know something about the files i had extracted. I could not correlate everything in the extracted fileset with what QPST seemed to expect, but the first challenge was to get QPST and the phone talking. using various drivers, QPST would sometimes see it, sometimes not, but nothing good seemed to be coming from it. I returned to trying to get SUT to work on my brick; again, with some drivers it would connect, but a flash always resulted in Error 4000 - DEVICE_NOT_CONFIGURED.
Then I read somewhere that someone had found a driver change made SUT work, so i investigated drivers more.
What I found was that if i ran up CWM, I got two Huawei devices in XP for which I could not find drivers.
The devices showed up as VID_12D1&PID_1022&MI_00 and VID_12D1&PID_1022&MI_01.
I took the Huawei USB drivers folder, and copied the qcser.inf then changed entries under [QcomSerialPort] to match my VID/PID values.
(the two that had matching MI_ values).
On driver update, I had a serial port, plus something I'd not seen before - a USB storage device which contained the phone's partitions!!!
This certainly seemed promising... so into SUT again, same error 4000...
So the I tried QPST; and yes, it could see the phone. Scared to do anything to brick it further, I thought, ok, try some memory diagnostics.
On running the 'Memory Debug' tool, as soon as I tried to get a list, QPST said 'this phones in diagnostic mode, it must be in download mode to do memory diagnostics', but even better 'Do you want to set it into download mode now?'!!!!!
Yeah! click the button, and I see a screen I've only seen once before (and i don't know why last time), black, with a line added every few seconds... which from all my reading I know is a good sign.
OK, then I closed all QPST apps, and ran SUT.
This time, the firmware flashed no problem. Was a bit worried as boot time is long (but it was effectively 'first ever' boot for the phone).
I hope this helps someone else with this or another Qualcom based phone.
Basic lesson is:
If you see Error 4000, it may be that the phone is in diagnostic mode rather than download mode.
If you don't have drivers, or don't have the right drivers, check you VID and PID, and try putting them into the .inf file
QPST may have a simple use after all... to force a phone into download mode when SUT fails.
Click to expand...
Click to collapse
it is working thanks bro
Stock rom download plz.
btsimonh said:
I just wanted to relate my experiences in de-bricking this U8850 phone.
I installed 'Apps_2.6.35.7-perf+root+CWM_recovery 5.0.2.8' (firmware.nb0) using SUT to get CWM, and then installed Danile's 4.1.2
Good as far as it goes, but i could not for the life of me reproduce his kernel (my kernels are always unreliable), so after many days of playing, i decided to take the phone back to stock to see if i could reproduce the huawei stock kernel as a base to work on.
The problem was, how do you revert to stock; the phone was no longer recognised by SUT?
So I took a stock .nbo file and extracted the content (some java extractor found with google) in the hope that I could create a CWM flashable zip of the stock firmware.. a bit of research later, and i thought i had got the gist, put boot.img and system.img into a zip with a modified script file, and voila... a bricked phone.
At this point, i had CWM, but if the phone booted, it showed a flash of blue screen (I didn't know these ran windows ), and back to huawei logo. Also I think i had to dismantle to disconnect battery to run CWM, as it's not available just on the volume-up-power restart.
So then I did more research, and came across QPST, Qualcom's tools. It seemed this should know something about the files i had extracted. I could not correlate everything in the extracted fileset with what QPST seemed to expect, but the first challenge was to get QPST and the phone talking. using various drivers, QPST would sometimes see it, sometimes not, but nothing good seemed to be coming from it. I returned to trying to get SUT to work on my brick; again, with some drivers it would connect, but a flash always resulted in Error 4000 - DEVICE_NOT_CONFIGURED.
Then I read somewhere that someone had found a driver change made SUT work, so i investigated drivers more.
What I found was that if i ran up CWM, I got two Huawei devices in XP for which I could not find drivers.
The devices showed up as VID_12D1&PID_1022&MI_00 and VID_12D1&PID_1022&MI_01.
I took the Huawei USB drivers folder, and copied the qcser.inf then changed entries under [QcomSerialPort] to match my VID/PID values.
(the two that had matching MI_ values).
On driver update, I had a serial port, plus something I'd not seen before - a USB storage device which contained the phone's partitions!!!
This certainly seemed promising... so into SUT again, same error 4000...
So the I tried QPST; and yes, it could see the phone. Scared to do anything to brick it further, I thought, ok, try some memory diagnostics.
On running the 'Memory Debug' tool, as soon as I tried to get a list, QPST said 'this phones in diagnostic mode, it must be in download mode to do memory diagnostics', but even better 'Do you want to set it into download mode now?'!!!!!
Yeah! click the button, and I see a screen I've only seen once before (and i don't know why last time), black, with a line added every few seconds... which from all my reading I know is a good sign.
OK, then I closed all QPST apps, and ran SUT.
This time, the firmware flashed no problem. Was a bit worried as boot time is long (but it was effectively 'first ever' boot for the phone).
I hope this helps someone else with this or another Qualcom based phone.
Basic lesson is:
If you see Error 4000, it may be that the phone is in diagnostic mode rather than download mode.
If you don't have drivers, or don't have the right drivers, check you VID and PID, and try putting them into the .inf file
QPST may have a simple use after all... to force a phone into download mode when SUT fails.
Click to expand...
Click to collapse
HOLY GOD! F**K ME!!! I finally did it! THANKS A LOT, BRO! YOU'RE AWESOME!!!
Hi all,
I have a Star/Bluebo B6000 phone which I believe is based on the MediaTek 6589T.
I followed the procedure here: http://forum.xda-developers.com/showthread.php?t=2206421
to set up a new ROM for the phone.
I seemed to have gotten it all done properly, but the phone only stays connected for about 2 seconds. The SP Flash tool moves into the red progress bar and then just fails.
Luckily, there isn't any software damage on the phone (from the look of it).
I'm trying to put in a new ROM to actually fix a previous issue where my phone remains on but when I press the home button or the power button the screen stays blank. Think a new ROM/fresh start may solve this.
But the core issue is that I am unable to put in a new ROM because the phone doesn't remain connected long enough.
Is there a solution to this? Or is there another way to install ROMS?
Thanks.
There are several things the issue could be.
Try running SP Flash Tools as Admin.
Try a different USB cable.
Try uninstalling current drivers and using PDANet VCOM USB drivers
Try a different PC
Try MTK Flash Tool as opposed to SP Flash Tool.
Make sure the scatter is correct. Create a new scatter with MTK Droid Tools
None of them work.
I've tried 4 different cables. MTK and SP tools.
It seems as though something is wrong with my preloader. When I try to 'restore factory settings' or even try to restart in recovery mode, the phone doesn't do anything. It's almost as though these modes don't exist or are bugged/busted.
EDIT: Yes, it seems to be some kind of preloader issue. When the phone is OFF, I connect the USB (which the computer recognises) and the within 2 seconds the 'disconnect' sound comes up. Within 2 seconds after that the battery charging shows up on the phone.
I say this because when the phone is ON, I am able to transfer files onto the phone and treat the phone as a normal connection. Something within the phone's software is causing SP Tools/MTK Tools/Other drivers not connect to it. I have a feeling I may have a corrupt/broken preloader/recovery system.
Thanks for the help. Please do advise as to what I can do.
Anyone?
Really could use some help.
vika09 said:
Anyone?
Really could use some help.
Click to expand...
Click to collapse
Hi, did you manage to get this sorted?
Hi guys, I recently purchased a Homtom HT3 for my mother, when it arrived to me I charged it and checked it out a bit just to make sure everything was fine which it was.
She collected it from me the next day and told me she'd start to use it the day after, she calls me up the next day and tells me there's some problems with it and a few people at her workplace tried to fix it for her to no avail. I pick the phone back up and I notice that everytime I power it on, it gets stuck on the "homtom" logo.
As I don't know too much about fixing phones I only took the following steps before asking for advice here; I went into recovery mode by holding up volume and power button, the android guy with the red triangle appeared so I tapped up + power button to get into the recovery(?) menu. I wiped the phone to factory settings and deleted the cache in there but it hasn't fixed the problem.
I assume I need to flash a firmware or something to potentially fix this, but I'm unable to find an official firmware from doogee/homtom's site for the HT3. I've found a firmware that I downloaded from "chinagadgetsreviews" but I'm a bit weary to try and flash with that rom because it isn't from the manufacturer. (even if I knew how to - the only experience I have is rooting my own phone but that's when I actually had access to a working phone, not one thats stuck on a boot logo).
Sorry for the long post but could anyone guide me in the right direction here? TIA
I'm not opposed to not using official firmware, I think I use cyanogen mod(?) on my own phone. I'd just like the problem fixed in the easiest way possible.
Trying to fix it myself by flashing a rom via SP flash tools but I've ran into another problem which is stopping any kind of progress - the phone isn't detected in Windows, I can't enable usb debugging because I can't get passed the boot loop, I've tried installing the ADB driver manually which didn't seem to work (just said it didn't install correctly and left me with a yellow exclamation mark) and I tried to install it automatically via ADB driver installer but it just throws up an error that the device isn't detected.
Any help would be greatly appreciated.
Hello. I bought a Homtom HT3 and next day a done an update with sp flash tool. all gone ok, but phone now wont to turn on. I contact homtom and got all drivers and room to fix it. Now i have a problem , i hit download on flash tool , take off battery + pres volume down + conect phone on usb cable. My computer detect it as USB MTK PORT sp flash tool load only the first red line but not detecting phone info, then after 1 minute i get
s_ft_da_no_response(4001) da didn't send response data to flash tool.
I changed drivers port even to MTK preloader, but i get same error.
NOTE....... All drivers and rom i got original from HOMTOM.
Thanks to all who can help me.
I can show a screenshot if need.
Same here - any solution for this problem?
Kleos89 said:
Hello. I bought a Homtom HT3 and next day a done an update with sp flash tool. all gone ok, but phone now wont to turn on. I contact homtom and got all drivers and room to fix it. Now i have a problem , i hit download on flash tool , take off battery + pres volume down + conect phone on usb cable. My computer detect it as USB MTK PORT sp flash tool load only the first red line but not detecting phone info, then after 1 minute i get
s_ft_da_no_response(4001) da didn't send response data to flash tool.
I changed drivers port even to MTK preloader, but i get same error.
NOTE....... All drivers and rom i got original from HOMTOM.
Thanks to all who can help me.
I can show a screenshot if need.
Click to expand...
Click to collapse
Hi, so I have encountered a rather big issue with my xiaomi redmi 3 pro.
I believe I have flashed wrong (corrupted ? ) ROM, now I have a really annoying situation.
So, I flashed " ido_xhdpi_images_V7.2.6.0.LHPCNDB_20160129.0000.14_5.1_cn " in MiFlash, took a bit long time (nearly 15 minutes), afterwards it was completed, I disconnected my phone, and *BOOM* since then, black.
Current situation is this: When I connect my phone via USB, my phone gets recognized in device manager as
"Qualcomm HS-USB QDLoader 9008 (COM#)", also it gets recognized in MiFlash, but can't get it to work in fastboot, and it is not recognized as adb device. So, throughout 3 days now, I tried nearly EVERYTHING I have found on forums. The only thing I have not done is to take the back cover off and disconnect battery ( as I have seen on forums), tried with deep flash cable, all possible combinations of buttons and all. If the phone is connected to PC, when I press whatever combination of buttons on phone I just get Windows sound for connecting an USB device.
So today, when I connected it, red LED light was blinking, I have no idea what that was, so I plugged it into the wall to charge for 10mins, and now when I connect it, it's gone again, all black, no response whatsoever.
So, when I connect it to MiFlash and try to flash any ROM, tried nearly everyone I found, I get the same message; "Unspecified error 0x80004005; End Transfer packet id0, status 9" if I refresh MiFlash without disconnecting, and press flash again I get "Reached the end of the file. (0x80070026; Receiving hello packet) "
Things maybe to mention: I am running a 64 bit Windows 10, and my bootlocker is locked.
So I am wondering, if there is any possible way to solve this or it's time for a new phone?
alchzor said:
Hi, so I have encountered a rather big issue with my xiaomi redmi 3 pro.
I believe I have flashed wrong (corrupted ? ) ROM, now I have a really annoying situation.
So, I flashed " ido_xhdpi_images_V7.2.6.0.LHPCNDB_20160129.0000.14_5.1_cn " in MiFlash, took a bit long time (nearly 15 minutes), afterwards it was completed, I disconnected my phone, and *BOOM* since then, black.
Current situation is this: When I connect my phone via USB, my phone gets recognized in device manager as
"Qualcomm HS-USB QDLoader 9008 (COM#)", also it gets recognized in MiFlash, but can't get it to work in fastboot, and it is not recognized as adb device. So, throughout 3 days now, I tried nearly EVERYTHING I have found on forums. The only thing I have not done is to take the back cover off and disconnect battery ( as I have seen on forums), tried with deep flash cable, all possible combinations of buttons and all. If the phone is connected to PC, when I press whatever combination of buttons on phone I just get Windows sound for connecting an USB device.
So today, when I connected it, red LED light was blinking, I have no idea what that was, so I plugged it into the wall to charge for 10mins, and now when I connect it, it's gone again, all black, no response whatsoever.
So, when I connect it to MiFlash and try to flash any ROM, tried nearly everyone I found, I get the same message; "Unspecified error 0x80004005; End Transfer packet id0, status 9" if I refresh MiFlash without disconnecting, and press flash again I get "Reached the end of the file. (0x80070026; Receiving hello packet) "
Things maybe to mention: I am running a 64 bit Windows 10, and my bootlocker is locked.
So I am wondering, if there is any possible way to solve this or it's time for a new phone?
Click to expand...
Click to collapse
Hello,
I will move your thread to the correct section so that the experts there maybe able to assist you.
Regards
Vatsal,
Forum Moderator.
Hi, sorry to hear that happened to you. I suggest you to post this on Xiaomi reddit page, so more people can help you. Here is the link:
https://www.reddit.com/r/Xiaomi/