Hello Everyone,
I'm just wondering if anybody else if having the same problems as i am... my mic was working fine yesterday and today for some reason it does work.... but you have to litterly shout on the phone for somebody to even hear you and even then apparently its very quite.
I hope its not a hardware fault i doubt i have any warrenty because i dropped the phone about one mounth ago but everything was still working fine..
Hi good evening, I live in Brazil and since the last update made by sony I can not use the gps it stays looking gps locaiza correctly and not anybody here know how to fix this, detail is not root my phone and he still could not route if they can help me thank you.
I've the same problem, gps don't running and in code test #...* ° of sony xperia nothing, signal gps dead!
Nki from Italy
have you guyz tried to reflash back the official rom? wondering if its a case of bad flash? before this did you guyz have any gps problem?
Good evening. I have a problem with my phone. My firmware is V20E official. After updating to it, I noticed that GPS is not working properly, sometimes even not working at all, so I wanted to ask if someone knows how to fix it. Thank you.
Hello,
i just bought the note 3 N9006 mtk6589 today and i am very excited ! Everything works just fine !!!!!! air gestures, S-Pen works absolutely wonderful and everything ! BUT i saw 2 very small problems and i would like to hear some advice here.
When i powered on the device the vibration stopped working after some time and i resetted the phone and it worked again,but after some time it didnt work again.So i moved the phone a bit on the air 2 - 3 times and i hear something inside that i think its the vibration motor. then the vibration worked.well i dont think it is a very big problem that i need to return it.The vibration works now well i think it hasnt stopped working since the last time it did it. has anyone experienced this before with a similar phone?
The second problem is that the right side of the home button sometimes it sticks A BIT inside.but the home button works OK.is this dangerous that the home button sometime will stop working or break? i dont think so but tell me your opinion !
Despite these small problems i am very very pleased with the phone.
If anyone wants i can post some photos !
unstoppablegr said:
Hello,
i just bought the note 3 N9006 mtk6589 today and i am very excited ! Everything works just fine !!!!!! air gestures, S-Pen works absolutely wonderful and everything ! BUT i saw 2 very small problems and i would like to hear some advice here.
When i powered on the device the vibration stopped working after some time and i resetted the phone and it worked again,but after some time it didnt work again.So i moved the phone a bit on the air 2 - 3 times and i hear something inside that i think its the vibration motor. then the vibration worked.well i dont think it is a very big problem that i need to return it.The vibration works now well i think it hasnt stopped working since the last time it did it. has anyone experienced this before with a similar phone?
The second problem is that the right side of the home button sometimes it sticks A BIT inside.but the home button works OK.is this dangerous that the home button sometime will stop working or break? i dont think so but tell me your opinion !
Despite these small problems i am very very pleased with the phone.
If anyone wants i can post some photos !
Click to expand...
Click to collapse
i have the same problem please my mail is [email protected] i do have another problem with the loudspeacker volume (very low ) i have try the engineering mode --change some values but nothing... when you say on the air??
Dear support team,
i had a serious problem in my device galaxy mega 6.3 I9205
after i flashed the CM11 custom rom of android kit kat 4.4.2 on my device
i faced a serious problem, that the screen go black while a phone call is in progress,
and there is no way to light up the screen except after ending the call,
it seems that there is a problem regarding the sensors of the phone,
especially the problem is extended to the flip cover , the screen should react according to the cover is put on it or not,
so please help me, because i couldn't use my phone while a phone call is in progress...
Thank You ..
same problem
nourworld said:
Dear support team,
i had a serious problem in my device galaxy mega 6.3 I9205
after i flashed the CM11 custom rom of android kit kat 4.4.2 on my device
i faced a serious problem, that the screen go black while a phone call is in progress,
and there is no way to light up the screen except after ending the call,
it seems that there is a problem regarding the sensors of the phone,
especially the problem is extended to the flip cover , the screen should react according to the cover is put on it or not,
so please help me, because i couldn't use my phone while a phone call is in progress...
Thank You ..
Click to expand...
Click to collapse
Hi....
I am also having the same problem....
bsvinod said:
Hi....
I am also having the same problem....
Click to expand...
Click to collapse
i'm the third no solution?
And the same problem with my Mega 6.3 after flashing CM11 4.4.2 rom by silesh.nair. Somebody knows what's wrong with our phones???
No one helps I've installed program that shows proximity sensor values and it's look like sensor in my mega doesn't works correctly. It's recognizing "near" all the time and don't response for any actions. Maybe sensor is broken. I've tried to change sensor values, but it doesn't help anyway. I have probably lost warranty after flashing CM11 and really don't know what to do now
Sorry for my poor english...
nourworld said:
Dear support team,
i had a serious problem in my device galaxy mega 6.3 I9205
after i flashed the CM11 custom rom of android kit kat 4.4.2 on my device
i faced a serious problem, that the screen go black while a phone call is in progress,
and there is no way to light up the screen except after ending the call,
it seems that there is a problem regarding the sensors of the phone,
especially the problem is extended to the flip cover , the screen should react according to the cover is put on it or not,
so please help me, because i couldn't use my phone while a phone call is in progress...
Thank You ..
Click to expand...
Click to collapse
FILIP S. said:
No one helps I've installed program that shows proximity sensor values and it's look like sensor in my mega doesn't works correctly. It's recognizing "near" all the time and don't response for any actions. Maybe sensor is broken. I've tried to change sensor values, but it doesn't help anyway. I have probably lost warranty after flashing CM11 and really don't know what to do now
Sorry for my poor english...
Click to expand...
Click to collapse
Flash a custom ROM/Kernel and see if the sensors are fixed. If they aren't then it might be a bug or hardware failure
N7105 rocking AOSB with AGNi kernel,
Sent from the "China who bans Google"
Click "Thanks" if I was of any help!
Ah hell I'm not the only one having this problem then. I thought I was crazy!
Bump
i9100 proximity sensor doesn't work
Hi to all!
I have the issue with proximity sensor and didn't manage to find a solution in other similar threads!
The matter is that it is always stay as Released.
In the same time in test screen (*#0*#) there are changing reading for PROXIMITY parameter from 2 up to 240 with no ADC parameter at all. Please look for screenshots. PROXIMITY parameter changes its value when I move my finger in front of the sensor, but as I can understand Android doesn't recognize it because of ADC absence.
Moreover I tried to change proximity sensor for working one (from another phone), but it shows the same as mine (with no ADC readings).
After all I think it is software problem, but I don't know how to solve it. I flashed different firmwares (now it is XWMSE NeatROM v.6.4), but nothing helped.
Please assist! Thanks!