**************Flashing Hard Bricked Redmi 3 SnapDragon***********
This IS the Guide to Flash hard Bricked Redmi 3, using Deep flash mod, No Fastboot, No Edl, No Test point, very easy and simple, Hit :good: if this helpful for you,
Instructions-
First of all Prepare Deep Flash Cable using Below Guide
Attached Both Coper Wire and then connect this cable with your pc
Now connect your Device to usb [Make Sure Your phone is switched Off]
On Pc go To Device manager and Look on port, {No Available] Don't Worry]
Pull the attached Wire and look Device Manager a New port Is Available HS-USB Diagnostic 9008[ com5, com17 etc]
Ok your Device is ready For Flashing
Run mi Flash click on Browse and Load Fastboot Rom Folder
Click Refresh and Then Flash Done, wait a few Seconds While flashing IS complete ,
Done,
Bought a Deep Flash Cable @ AliExpress (for about 5€/5US$). It has a button to enable Qualcomm HS-USB QDLoader 9008 and for me is more secure then trying to risk to kill your mainboard via USB.
P.S.: I'm not good at DIY.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
plz sent me a cable at my village, lol, Delivery system Not Available For all Areas or this guide for that person,
Does this work with Redmi Pro?
Related
When you flash wrong rom or flash wrong file stock lg g2 :
Hand logo lg
No downloadmod
No fastboot
security error
Qualcomm 9006
Ok you need short testpoint lg g2 phone put qualcomm 9006 show very partitiont or short testpoint qualcom 9008 then use tool boardiag of my unbrick.
http://forum.xda-developers.com/lg-...9008-board-t3072073/post59949117#post59949117
How do short testpoint Lg g2 you need remove backcover
https://www.youtube.com/watch?v=nYTmTZkbfmU
Guid short testpoint
https://www.youtube.com/watch?v=8ZD98phYTsM
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Then short testpoint in picture
With qualcomm 9006 when install driver done (qhsusb_bulk) read video of him
https://www.youtube.com/watch?v=_d5b_osUTug
When flash done but phone normal not save. OK you need check model in front back board see pictrure
I think model wrong, lg g2 d802 but main board d800
You need unbrick file d800
then flash tot d800 done.
I short this point in picture below then use [TOOLS] SRK Tool 2.0.2 [ROOT/UNBRICK/UTILITY/BACKUP]- 20150503 to fix.
My story in my page https://www.facebook.com/droidth/posts/772287019556649
The original thread is always online http://forum.xda-developers.com/lg-g2/general/lg-g2-unbrickable-fix-real-hard-brick-t2904404
somboons said:
The original thread is always online http://forum.xda-developers.com/lg-g2/general/lg-g2-unbrickable-fix-real-hard-brick-t2904404
Click to expand...
Click to collapse
But not full guide and very hard user can not do.
I have an Archos 45 Helium 4g phone that I want to use after my usual phone broke.
The Archos hasn't been used for a couple of years and will not power up or charge the battery.
I have replaced the battery with a new one and also found the original would charge with a more powerful charger from a Raspberry Pi 3. However the phone will still not boot, nor enter recovery.
Plugging into a PC, the Qualcomm HS-USB QDLoader 9008 port is detected and drivers installed. I have downloaded the Qualcomm QPST utility which I understand can be used to unbrick the phone, but need a ROM to flash as part of the process. Archos offer a firmware download for the 45b model on their support pages, but not the 45.
Can anyone advise where I can get a ROM that would work? Is plain Android downloadable from Google?
Thanks.
Also can not see it at archos ftp
After a long search http://archoslounge.net/forum/showthread.php?33114-45-50-Helium-Inversion-de-carte-SD
If it is not working maybe get in touch with archos support the maybe provide a download link to you.
That forum also have cm11 or miui rim helium 45 thread
Good luck on unbricking.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Thanks very much for your response. I'll have a look and see what I can do with CM11.
Is someone still have the CM11 of Archos 45 Helium 4G??? As archoslounge.net is down
Thanks
Hello im trying to unbrick my phone using testpoint method but once i disassembled my phone the insides look different the from the guide i was following i managed to find an image showing where the pins are on my phone but they are not there. Instead there are lots of other pins around. Can someone please help me with this? I will post image of how my phone looks like (You cant rly see it but there are no pins where there are supposed to be instead there's only a straight copper like line).
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Thank you i getting desperate...
Seems like you are using The MTK version of Redmi Note 3 (judging by the SIM card pin) Unfortunately, Mediatek phones do not have testpoint pin.
hasel17 said:
Seems like you are using The MTK version of Redmi Note 3 (judging by the SIM card pin) Unfortunately, Mediatek phones do not have testpoint pin.
Click to expand...
Click to collapse
Well that sucks... so any idea how do i unbrick MTK version?
Peaceleaf said:
Well that sucks... so any idea how do i unbrick MTK version?
Click to expand...
Click to collapse
Download the fastboot ROM, disconnect ur battery and then plug ur phone in the computer, download SP Flash tool and select the files from the fastboot and flash it onto try and see if works ?
Hello and thanks for readingSo, i will to explain my situation:
The phone is stucked in edl.
The phone was runing miui 9.5.
The device manager see the 9008 qloader.
Mi flash tool see the device.
The led blink in red.
No mi logo.
No fastboot.
No vibration.
No unlock bootlader.
Here comes the errors:When i try to flash this fastboot room in the mi flash tool, i get the following error: Ping target failed.
Here screen shoot and log.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
View attachment log.rar
When i try with QFIL 2.0.0.3 i get this error (Device is not in firehose mode):
Aditional info:
I try with a couple of roms, devolper and stable.
I am triying to flash from windows 10 64 bit (driver enforce are disabled).
I tryed with deep flash cable (cortocircuit green and white)
When i try with older mi flash tool (2015), i get stuck in send nop comand.
I install and re-install drivers several times (qualcom).
I follow many guides, but most are to enter in edl mode, and then they can flash with no problems.
Here is a screenshot of the device manager:
The mi flash tool stuck few seconds in this, "ping target via firehose" before it ends in error:
Conclusion and what I think is the problemI think there is a soft problem with the emmc and the prog_emmc_firehose_8976_ddr.mbn, that does not let communicate the cellphone and the mi flash tool properly.
Other can be that the emmc went only read.
If is that the problem, is there any soft solution??
I would apreciate any help.
---------------------------------------------------------------------------------------------------------------------------------------------------------------
If you got here, thank you very much and sorry for my basic english.
Good day. The phone LG G3 VS985WK worked, but the Internet distribution via the SIM card of another operator was not available. I used a program SALT FWUL loaded from a USB flash (Live USB) drive to remove AntiRollBack. Through the inoperability of the Internet distribution, I also deleted the system partitions using the program SALT FWUL loaded from a USB flash (Live USB). After that, the program SALT FWUL does not detect the device, recovery does not start and no Download Mode. Moved the phone to Qualcomm HS-USB QDLoader 9008. When restoring the phone with the program BoardDiag (AP Check), an error appears "No response from the device. Check PMIC first and if stiil boot problem, replace AP". If you choose settings AP Check+EMMC Test or PMIC ON, then "Device was not found in dload trying flash programmer". Settings B2 (MSM8974AC) or G2 (MSM8974) and versions BoardDiag 2.99a or BoardDiag 3.99c do not affect, the error is the same.The program https://www.androidbrick.com/unbrick-recover-your-dead-lg-g3-g2-all-variants/ restores the phone, but only one port LGE AndroidNet USB Serial Port and one modem LGE AndroidNet USB Modem appears. I use Windows 7 SP1 Ultimate x64. Please help me recover the phone. I understand Russian and English.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Buy a new phone m8. VS985 are cheap.