Rohm was installed wrong phone
Now, the phone is a new operating system, but I did touch and the camera and the flash does not work
MT680 S7 G930FD
model rord : Z6U030HA
model:gxq6580_weg_l
More than 20 system experience
All the same problems
Touch inverse
Have you tried the firmware linked in this thread?
http://forum.gsmdevelopers.com/f51/samsung-s7-sm-g930fd-clone-mt-6580-firmware-here-12699/
Once it is flashed you may need to bring back the Samsung logo by rooting the phone and editing /proc/env_logo_id with a hex editor by adding 01 to the file. Save it, then restart the phone immediately for the changes to take effect.
His experience has been an ongoing problem
I don't understand you mate. If the above mentioned ROM doesn't work, you might want to try this ROM I dumped off my phone:
http://www.4shared.com/rar/6mMhYIk5ce/Galaxy_S7_mt6580_Z6U030HA_V105.html
Is there a password
I think the problem in Lisse rom
Deleted because the calibration file
When you attempt to calibrate the Miracle error appears:
* Waiting for USB Port ...
** Set? PreLoader USB VCOM Port (COM5)?
** Please Hold "ON" to connect with the phone ...
** Waiting for USB Port ...
** Set
** Connecting AT Mode
** Test Mode, Reading Information From the Phone ...
>> Completed, but data not Found
No, the ROM isn't password-protected.
Try pressing the reset pin on top of the phone and see what happens when you connect it.
I did not understand the meaning
Try pressing the reset pin on top of the phone and see what happens when you connect it.
There is a small hole at the top of the phone which you can press with a needle. Press it, and see if it works.
blakegriplingph said:
There is a small hole at the top of the phone which you can press with a needle. Press it, and see if it works.
Click to expand...
Click to collapse
Did not benefit a pin button is pressed
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
I think I need me lcd calibration files
Touch from the bottom and right side parked
I have the same problem. Looking for a solution as well.
Related
Hey Guys!
I purchased two android TV boxes few months back. and one box got stuck at the android logo and i flashed it using MATRICOM_MX2_115_FULL_AUG_09_2013.imgc image file, and now it works fine.
The other box just shows a blank screen nothing displays. When i power it on the LED flashed and then nothing else. I tried to flash it but it ddnt work just the black screen.
i took it apart to flash it and this is how it looks.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Any help appreciated guys....
Thanks.
same problem but cant flash
I have the same box, i took it apart to find the reset botton, i couldn't find any. It is stuck on the android logo, how did u manage to flash it. Plz provide ur steps.
afshandc said:
Hey Guys!
I purchased two android TV boxes few months back. and one box got stuck at the android logo and i flashed it using MATRICOM_MX2_115_FULL_AUG_09_2013.imgc image file, and now it works fine.
The other box just shows a blank screen nothing displays. When i power it on the LED flashed and then nothing else. I tried to flash it but it ddnt work just the black screen.
i took it apart to flash it and this is how it looks.
View attachment 2778028 View attachment 2778044
Any help appreciated guys....
Thanks.
Click to expand...
Click to collapse
I also have the same problem with my device. it doesn't have any reset or volume button on it. I posted about my problem here:
http://forum.xda-developers.com/general/xda-assist/android-box-stuck-boot-logo-t3127923
could you please provide the steps you took.
I found a part on PCB board which said recovery so I connected the two pin and I got it into recovery but there is no option there. there is also three holes which says debug but I don't know how to connect it to pc.
I had a same device and using Online Nandroid backup I made a backup of the ROM which gave me boot.img recovery.img and some other files I put them in the SD card and put the device on recovery but nothing starts and there is only an android guy resting with no option and since there is no volume or power button I can't get into any option
thanks
This is also a picture of the board
I bricked my Blu life one x and I want to repair it can someone help me out ow to do it and where I can't find the Blu life one x rom?
Download this:
https://www.androidfilehost.com/?fid=24391638059058964
From user @Bad_MOFO_33
Then download the SPFlash tool from here:
http://spflashtool.com/
Then be sure to have usb drivers installed so the COM identifies your phone.
Open the ROM you downladed and extract the carpet into desktop or somewhere you can easily find it.
Open SPFlashtool and go to the DOWNLOAD window and select Scatter-loading and select the scatter file from the folder where the ROM is like this:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Then with the phone turned off (surely is off since its bricked) click the DOWNLOAD button on the spflashtool
And then AFTER you clicked DOWNLOAD on SPFLASHTOOL connect the phone while holding the VOLUME UP and is should identify it and begin the process.
DONT disconect until its done and a BIG GREEN CHECK mark appears, then just unplug and power it on.
ANd thats it
-------------------------------------------
Sorry i dont know why the image is not loading but hopefully the instructions will guide you
Thanks I'm going to try it tomorrow.
Thanks bro... It has worked.... But now I have a different problem... The sim doesn't get recognized.
azazsxsxdcdcfvfv said:
Thanks bro... It has worked.... But now I have a different problem... The sim doesn't get recognized.
Click to expand...
Click to collapse
Might need to repair your IMEI
Follow this guide:
http://sheershbansl.blogspot.mx/2014/08/how-to-fix-invalid-imei-3-methods.html
NOTES:
1.- you IMEI numbers are on the battery sticker theres 2 of em one for sim 1 and the other for sim2
2.-when entering the imei where it say to type AT+ etc etc on our BLU you need to type AT (SPACE) + and the rest, so it looks like AT + and then all the rest (EGMR=1,7,"1234567890")
3.- remember to SET Command and then reset so the IMEI settles in.
Hope thats the problem solver
Thanks for all guys that helped me... The sim problem was my fault cause I messed around with the bands. Like north America and world bands...
Please I have a big problem with my device
after receiving it I connected my box to the tv but after the ANDROID logo the screen is black and after 15 minutes it emits a long beep
I tried to make wipe reset and install another firmware but the same problem
after 4 reboot box make a long bip
after 5 reboot it's bricked on remote connect "picture"
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
but after reboot it's bricked one more time on black screen
Thank you
sacretboy01 said:
Please I have a big problem with my device
after receiving it I connected my box to the tv but after the ANDROID logo the screen is black and after 15 minutes it emits a long beep
I tried to make wipe reset and install another firmware but the same problem
after 4 reboot box make a long bip
after 5 reboot it's bricked on remote connect "picture"
but after reboot it's bricked one more time on black screen
Thank you
Click to expand...
Click to collapse
Your MiBox is not the problem........
You have an out-of-spec USB thumb drive. You cannot perform successful flash until you use a freshly FAT32 formatted USB thumb drive. Keep trying different flash drives til you flash properly. Smaller drives are better!!
Current world's record is 9 different flash drives until a reliable flash.....
Be persistent
mine is in same situation..... only black screen. just power light and a red light on audio jack
averrone said:
mine is in same situation..... only black screen. just power light and a red light on audio jack
Click to expand...
Click to collapse
did you find any solution? Mine is the same after the update.
anup756 said:
did you find any solution? Mine is the same after the update.
Click to expand...
Click to collapse
no... i dint find it....
Hello XDA community! I need help putting this Tomate S905XQ box in bootloader mode so I can flash it using USB Burning tool.
I tried everything without luck.
What I have done so far:
Plugged the USB cable in the PC, hold the visible RESET then UPDATE buttons but unfortunelly, no dice. (Do I have to plug the ac adapter)
Also tried holding the "hidden inside" UPDATE button but also without any luck.
I want to flash Aidan's Custom ROM v9 on this box (1GB/8GB).
Any help is really appreciated, including how to backup this firmware because I haven't found any version on internet.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Try shorting it , the pins are on the chip just above where it says 905x , have the box attached via usb and have the usb burn tool open , get somehing like sim tray tool and one by one place it in between the pins untill it shorts it will connect ...you may or may not need power plugged in and make sure you use the otg usb slot..
Good luck
Thank you very much for your reply! I'll try that on the weekend.
as mentioned above shorting the pins AKA Mask ROM Mode will be your awnser, look at this thread, look for same type of chip as you have (M logo) even if chip aint the same number mask rom mode will probobly (but not always) be the same, there are 2 chips similar to yours in the thread, so try with those 2 first
NAND Chip Mask ROM Mode Short Location - FreakTab
Hi Everyone We have created this thread to collect all the NAND pin Short to Mask ROM Mode locations for all our members. Because firmware comes on android
forum.freaktab.com
Ok, so i got this random Huawei P20Lite right?
Back isnt pealed off, works fine, no damages.
BUT WAIT... About Works Fine... It Wont really boot up into The OS!!!
Somethimes shows this really weired Image when pluged in and charging the phone, or randomly:
A green Screen with a Red Square on Top and a Blue one Down.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Not My Picture
It will then boot up and greed you with A:
Again, not my Picture.
Acording to Huawei, You have to Use HiSuite to recover it.
1. Put the Phone into Fast Boot. AND conect to PC
2. Open HiSuite on Your PC and click on Recovery mode or whatever its called.
3. i donk know i forgot.
anyways, i get this nice little message
(In translated, this means That: Your Device doesnt support System Recovery.
Bro wth
Anyways, our phone story doesnt end there...
I tried doing it without the Computer.
using eRecovery!!! not surprising i know...
Still, it was stuck on booting animation trying to enter eRecovery.
According to Huawei, "this message is displayed when a system file is replaced or modified, or the system is manually updated to an unofficial version". They were responding to another user with the same issue as mine.
I think that this is the Issue. Still, the instructions to fix it, dont work. (as tested above.)
Tutorials show the eRecovery method without the PC.
Here are some info i found:
Another Guy having the same issue:
i forgot the link but someone else on XDA Had the same issue.
please help!!!
hello sir did you have any luck resolving this issue (I've purity much looked every were but I had no chance)