I have a hard bricked Elephone p9000 does not turn on and has no working buttons. Have fallowed many tutorials on how to fix but all keep ending in the same result*BROM ERROR : STATUS_EXT_RAM_EXCEPTION (0xC0050005) I have fallowed instructions and have tried to flash just the preloader, I have tried to format, I have tried to firmware upgrade I have tried every option the sp flash tool offers all met with the same result**BROM ERROR : STATUS_EXT_RAM_EXCEPTION (0xC0050005) when i look online it tells me to try a different port but i have been trying to fix this at least*a little*BROM ERROR : STATUS_EXT_RAM_EXCEPTION (0xC0050005). I am using the test point on the circuit board to get the PC to recognize the phone and it attaches and detaches over and over but if i hit download on the flash tool it starts and goes to 100% on the first red bar but can not get it to go past that no matter what i try holding vol up or down when plugging in makes no difference**
* I am trying to flash the original stock rom. Can someone help me out please ? Thanx*advance**
flash 20160304 rom,. if that dont work then remove the battery and flash it but it will void warranty
Help with P9000!
Hi
I had exactly the same thing happen to my P9000. Now stuck with a BROM ERROR: STATUS_EXT_RAM_EXCEPTION
Did you find a fix?
Related
Hi all,
please help me out because I'm desperate.
Yesterday I received a THL W8 mobile phone and I flashed it with the ROM reported on this thread.
Once done, my SD card wasn't recognized by the phone, so I decided to flash the same ROM again.
Unluckily, my bad, I didn't uncheck the PreLoader tick and as result now the phone doesn't boot at all.
The PC recognizes it and the drivers are ok, but when I try to flash a ROM, any ROM, I get different errors.
With SP Flash Tools version "SP_Flash_Tool_v3.1304.0.119" the bottom bar fills red fully (100%) but after about 40 seconds it gives me the following error:
S_FT_ENABLE_DRAM_FAIL (4032)
With the SP Flash tools version "AntiBrick_Flash_Tool_v3.1224.0.sn85" 3 seconds after the bottom bar gets filled in red, the following error is returned:
SP FLASH TOOL ERROR: (8200)
[Platform Error] The load and target are inconsistent!
I've also tried to flash the stock ROM but with the same bad results. More, I tried to do a reset with both the aforementioned Flash tools versions with success, but after that whenever I try to flash the phone with any ROM, I get the same errors as before.
Since the PC recognizes the phone I'm kinda sure it can be restored, but apart what I tried already, I'm out of ideas.
Any help is welcome
Thank you guys
Cheers
Heide
really? no one really answered the poor guy, the phone ended up bricked for good after all
What happened:-
I have Micromax A114(Canvas 2.2) which has MT6582 chip. One day when I restart my phone got a screen with white background that says "Encryption Unsuccessful" you need to reset ur phone. I tried to wipe cache and data from recovery it said "unable to mount". So I re-flashed the official stock rom(the one that I was running on my phone) but the flash process was unsuccessful.
You will find all the screenshots here http :// download. pratiyogitadarpanpdf. com/cover/a114flash /index.php
What is the current situation with my phone:-
It is not starting up not even any sign of charging when connected to charger, but when connected to my laptop it shows "Micromax A110 Preloader USB VCOM Port (COM42)" in the device manager. Sometimes it also shows "MediaTek DA USB VCOM Port (COM73)"
What I've tried:-
1. I tried flashing different ROMs compatible with my phone but getting the Brom error s_dl_pmt_err_no_space (5069). So, it is not the problem with the size of ROM, i guess.
1.1 Flashing with "firmware upgrade" option throws "Failed to get PMT info"1.2 Flashing with "download" option says "partition management table is not found. Please use "format+download" option."1.3 Flashing with "format all + download" option throws "Brom error S_DL_PMT_ERR_NO_SPACE (5069)"1.4 When tried to auto format flash (with format flash except bootloader option), it says "S-DL_READ_PT_FAILED(5073)":crying:2. I used different versions of sp_tools from 3.2 to latest version 5. But, still getting the same error with all versions.
3. I tried to readback with sp tools it says OK.
4. When I tried memory test in sp tools with the scatter file of official rom(that was running fine on my phone earlier), it gives error S_DA_SDMMC_WRITE_FAILED (3149) and same old NAND FLASH NOT DETECTED error in the output.
5. But when I flashed only the preloader of the same rom with "format all + download" option, it was formated and flashed successfully.:fingers-crossed: But then try to flash the other files of that same rom, it again shows "Brom error S_DL_PMT_ERR_NO_SPACE (5069)"
6. I don't have Mtk_Droid_Tool backup files for my phone. And it is not detecting my phone.
7. I read other threads on XDA with similar symptoms but no luck.
What should I do now? Help needed.
I tried searching for the solution on the internet continuously for like 4 days and found things that do nothing. Please suggest me what to do? Should I giveup or what? I love my phone very much:crying:. I seriously need your suggestions.:angel: Any help would be highly appreciated.
occurred same problem with my phone canvas 2.2
occurred same problem with my phone canvas 2.2 before 4 days and I am trying to search out any resolution on internet but yet not succeeded; Let's hope someone from XDA will help us in this matter.
mcn18cm said:
occurred same problem with my phone canvas 2.2 before 4 days and I am trying to search out any resolution on internet but yet not succeeded; Let's hope someone from XDA will help us in this matter.
Click to expand...
Click to collapse
fingers crossed
I am facing the same problem! Exactly the same problem with the same device.
Any solution to resolve this error?
Brom error: S_dl_read_pt_fail (5073)
i have the same prlbm .....
do you guyzzz have any solutions...??
I just hard-bricked my phone(Canvas Magnus A117) as well. No luck in finding any solution to this. It was working fine until I decided to reboot it just like that. Got the same errors after trying at the same level.
Same problem happened to my A114
Anyone get their phone rectified?
I had same problem while flashing. I took it to 2-3 places, they said it cannot be rectified. I however did not contact service center. Anyways, did the problem solved for anyone of you
I have a problem with my Paris X device. I had an unofficial rom and I wanted to flash the official one. When I started the flashing process with SP flash tool I got this message: "BROM ERROR: S_INVALID_BBCHIP_TYPE (0x3EB)"
Since that my phone is like dead. I cant switch on, I cant either flash again because my driver disappears in 2 seconds and I got the same error everytime.
Please help me, I would really appreciate it. :fingers-crossed:
hi i also bought paris x last year tried to flash it today using sp flash tool with official android 6 rom everything fine until i clicked download...
pmt changed rom - error #1
so then i looked up im supposed to switch to firmware upgrade but that resulted in error
s_invalid_bbchip_type - error #2
now my phone is bricked and whenever i connect it to my pc it appears for about 2 seconds and then disappears...
well im hoping that someone here could actually help cause this is really frustrating and i need to be able to use my phone next week... :/
thanks for replys
same probleme here
invalid bbchip type (0x3eb)
If anyone have this solution, Then please reply
I have also this type of problem In my Intex ace mini mobile
I also experienced problems like that, and couldn't solve it.... ERROR: S_INVALID_BBCHIP_TYPE (1003)
slekdor50 said:
I also experienced problems like that, and couldn't solve it.... ERROR: S_INVALID_BBCHIP_TYPE (1003)
Click to expand...
Click to collapse
Check the scatter, make sure that the line, i.e. matches the device chip type:
platform: MT6735M < -- is this correct?
peti2ty said:
I have a problem with my Paris X device. I had an unofficial rom and I wanted to flash the official one. When I started the flashing process with SP flash tool I got this message: "BROM ERROR: S_INVALID_BBCHIP_TYPE (0x3EB)"
Since that my phone is like dead. I cant switch on, I cant either flash again because my driver disappears in 2 seconds and I got the same error everytime.
Please help me, I would really appreciate it. :fingers-crossed:
Click to expand...
Click to collapse
I think this is scatter file mismatch, because I have done a proper read back of Inew L4 mt6735 to flash it to another phone with exact same model and build. But that flash file is not even working to flash that phone from which I made it giving this same error.
ERROR: S_INVALID_BBCHIP_TYPE (1003)
Still working on it.
[Update]
Only a single "m" in MT6735M in scatter file was missing, now its working all fine. :fingers-crossed:
I searched the whole internet for years to solve this error...
So if your getting this error better check your scatter platform names etc.....bcz even if you get it from readback or official flash files, like in my case it can give you error.
If you're getting this same error every time so try the above advice and here is a tip for early disconnection, connect while holding volume button or open yiu device and find kcolo[\B] and short it with GND.(better find details from google bcz i am too funding it)
Hi guys, sorry I'm newbie so after a long time surfing for solutions, I couldn't solve my own problem. That's why I come here to ask for your supports
Firstly I unlocked bootloader, installed TWRP and rooted my device and enjoyed it. But after decided to wipe (factory reset) this phone with TWRP, and my problem began...
1. I got stuck in TWRP loop booting. After that I tried to fastboot system.bin, cache.bin and recovery.bin from Stock Firmware but it still hung at Nokia logo booting
2. I still kept trying with SP Flash Tool, Miracle Box but there was still no hope:
- SP Flashtool v5_1548 gave me error: BROM ERROR: S_BROM_CMD_STARTCMD_FAIL (2005)
- Miracle Box 2.27A told me there was an error (i don't remember the code) occured in the location (i can't remember its code either)...
Anyone can solve it please help!!!! I love this phone much and as of now still suffering day by day since I can't do anything with it.
Kindly appreciate any suggestion and solution.
Thank you all!
Can you provide me the stock rom link please?
@you download firmware . Youtube : type "nokia ta 1066 flashing" GSM TEAM
@you flash this firmware , tick only recovery.bin
@notes : hold volume up & volume down -----> NO error: BROM ERROR: S_BROM_CMD_STARTCMD_FAIL (2005)
good luck ^_^_^//
@i'm using Nokia 1 Red TA-1047
Hello guys! I have a problem with one phone that i am trying to fix for someone and I feel sooo, sooo completely lost in all of this as I know almost nothing about this. The cell phone model that is in question is Alcatel One Touch Pop C3-4033x.
It seems to be using a Mediatek chipset and I was reading some of your advices here & there and tried using the program called SP FlashTools but it always resulted in error, in the end. It seems that something is wrong with this phones emmc flash memory. So, I tried transfering some files as a zip files to the SD-card and tried to apply update from it, but it said always: Installation aborted. And then, I have tried looking for a way to flash stock firmware of that specific Alcatel model on SD-card, but I just don't have any clue how to do it, if it is possible, even. Maybe I should just give up trying?
Oh, I almost forgot to write that the phone doesn't have the access to Android OS and USB debugging isn't turned on, because computer doesn't seem to list it and I don't know if there any button combinations that Alcatel uses for this model to get into that fastboot or adb mode, even though have installed mediatek drivers. It can only get into Android System Recovery 3e. That seems to be everything, I think, at least.
Oh guys, I am so, so, so sorry if I am bothering you with this. I just didn't know what or where else to ask this. Thank you sooo much!
Hi download those files:
Firmware:
https://www.mediafire.com/file/bpm4ibsbmr4q6nc/OT-4033X-Without_Mobilis_logo__BY_GSMSERVE.rar/file
SP Flash tool:
https://androidfilehost.com/?fid=11410963190603870440
Driver:
https://mega.nz/#!8VYkQCxD!fkhTrZwFFILDAglO1cR_8pIM4Cel52brZ7RB6QZoc6o
Once you downloaded all right driver open SP flash tool and add Scatter file
MT6572_Android_scatter.txt
Click on Download , connect your phone without battery and see if the process is going on if not try again with battery inside.
If you end up with error do the same thing but now first do Format then after is Finish do Download. Good luck ...
It still displays error :/
Teddy Lo said:
I have tried to do everything like you have said, but it still displays error when i press the Download button, and it displays that error after some seconds pass and also the same happens hen i try to use the Format function. This is the error it displays when i tried with the download button: BROM ERROR: S_DA_SDMMC_WRITE_FAILED (3149)
And this is the same error it displayed when i tried using the Format function: S_DA_SDMMC_WRITE_FAILED (3149)
i am so, so sorry for bothering with this.
Click to expand...
Click to collapse
Try with another version of SP Flash tool little bit newest .