Alright, so I screwed up my watch a few days ago and it ended up not getting past the splash screen and going straight to recovery. Thanks to @z0mghii, I was able to get a TWRP backup of the system, boot, and data. I replaced this backup with my own so none of his data (if possible) could be taken advantage of. However, after flashing it, I was still unable to boot up. Here are the steps I took in order to get everything back to working order. Keep in mind this is for WREN, the small version. Some steps may be unnecessary.
1. Boot to TWRP
2. Go to advanced wipe
3. Wipe everything
4. Go to the link below and download the TWRP Backup
5. Create a backup of a small partition (like boot) on your watch to create the folder.
6. Plug watch into PC while in TWRP
7. Go to the watch's internal storage
8. Go to the TWRP folder
9. Go to the subfolder
10. Paste the downloaded backup folder into this folder, this should be with the one you created earlier
11. Restore this backup on your watch, be sure to check all the boxes
12. Reboot to the bootloader
13. Install ADB if you haven't already, I recommend the 15 second one
14. While the watch is in the bootloader and it is plugged in, type the following commands
fastboot erase cache
fastboot erase misc
fastboot reboot
https://drive.google.com/drive/folders/0B_HUnwYIrFskUW10UDZ0dXdHQzg (You might have to download each item and put them in a folder instead, unless I'm oblivious to something, sorry )
After this, your watch should boot up, then power back down, then boot back up again. This will be followed up by the boot animation and go to the welcome screen.
If any of you guys could provide me with the latest stock rom version TWRP backup or a stock recovery.img, it would be greatly appreciated. (Unless June patch is the latest). The recovery would be great no matter what. Getting the stock recovery can be done by typing the following commands into the command prompt on a PC. Hopefully they work. It should be copied onto the /sdcard.
Via adb shell (make sure ADB debugging is on in developer options, then type adb shell in CMD on PC) type: cat/proc/mtd and press enter
You will see which is recovery partition and then type: dd if=/dev/mtd/mtd1 of=/sdcard/recovery.img (note that mtd1 you must replace with number which is recovery partition)
I hope I helped somebody with this. Again, huge thanks to @z0mghii for making this possible. I'm sorry for bad formatting.
I'm really new to this. I'm also by no means a developer/hardcore android person. These commands were all taken from google. I take 0 responsibility for your device being ruined. This is just what worked for me.
Reserved
HOLY CRAP IT WORKED!! You just don't know how much this means to me, words can't express!
cland216 said:
HOLY CRAP IT WORKED!! You just don't know how much this means to me, words can't express!
Click to expand...
Click to collapse
Hell yeah. Glad I could help somebody! I've been wanting to give back to the wonderful XDA community for a while as a long time lurker. Also, I'm hoping to get a newer version of the stock rom and a stock recovery.img so you can go back to 100% factory stock for an OTA. I'm pretty proud of myself (being noobish) figuring this out.
Thanks a lot!! My watch was kept in a drawer because it was useless and it has now returned to life, I just have a problem restoring the recovery, the command to locate the recovery folder do not work me, have any idea how located the recovery folder?
klaudio_tv said:
Thanks a lot!! My watch was kept in a drawer because it was useless and it has now returned to life, I just have a problem restoring the recovery, the command to locate the recovery folder do not work me, have any idea how located the recovery folder?
Click to expand...
Click to collapse
Are you referring to "extracting" the recovery img? You only need to do it if you're running the stock recovery.
If so, I think I have screwed the command. Make sure you're in adb shell (in recovery on the watch) and then type "cat /proc/mtd" (with the space in front of cat) without the quotes in order to locate the recovery partition.
You will see which is recovery partition and then type: dd if=/dev/mtd/mtd1 of=/sdcard/recovery.img (note that mtd1 you must replace with number which is recovery partition)
Hopefully this works
Hi, my watch now works well, but I was not able to install updates, when I try to install updates from the watch, watch reboots and go to TWRP recovery. Anyone knows how install the updates?
klaudio_tv said:
Hi, my watch now works well, but I was not able to install updates, when I try to install updates from the watch, watch reboots and go to TWRP recovery. Anyone knows how install the updates?
Click to expand...
Click to collapse
Since the OP helped me, here's my chance to give back..
By no means do I know what hell I'm doing, but I know enough to be dangerous. If you're ready to live dangerously, follow these steps (which worked for me):
1. Go into TWRP on the watch and connect it usb to your computer. Using TWRP file manager, copy the update.zip from CACHE to sdcard\Download.
2. On the computer, browse to Zenwatch internal memory Downloads folder and copy the update.zip file to your computer.
3. Unzip the file on your computer using 7zip.
4. Navigate to \META-INF\com\google\android\ and look for updater-script.
5. Edit updater-script in Notepad++.
6. Delete the lines starting with getprop. This turned out to be lines 2 thru 5.
7. Delete the lines starting with apply_patch_check. This turned out to be lines 10 thru 176
8. Save changes to updater-script then in Windows Explorer highlight all of the files and folders that you unzipped, right-click them and click on 7zip --> Add to update.zip
9. Copy the new update.zip to the Zenwatch internal memory, Downloads folder, overwriting the original update.zip
10. Flash the update.zip file with TWRP.
11. Reboot TWRP to Bootloader.
12. On your computer, goto adb folder where you have fastboot files, and using command prompt type:
fastboot erase cache
fastboot erase misc
fastboot reboot
These steps worked as I was stuck on the June 1, 2016 Android security patch on my Wren Zenwatch. These steps helped me get to the September 1, 2016 security patch.
I managed to update my watch to the September 1 security patch using Cland216's method. But I am unable to update further using the method above. Does anyone have any info on how to update further? Or has any zip files to flash?
If we could get someone to upload the watches stock recovery that would solve all issues.....Why has noone done this for this model yet?
Sent from my OnePlus X using XDA Labs
I'm unable to create a backup file
5. Create a backup of a small partition (like boot) on your watch to create the folder.
6. Plug watch into PC while in TWRP
TWRP :
Could not mount /data
When I try to mount /data , I unable to /data
HOLY ****
Dude.. Let me just say...
YOU ARE THE ****ING ABSOLUTE BEST.
I am now going to make a backup, and save it to my computer, google drive, dropbox, icloud, and every other ****in place I can to make sure this never happens again. Thank you!!!!
Nicholas6706 said:
Alright, so I screwed up my watch a few days ago and it ended up not getting past the splash screen and going straight to recovery. Thanks to @z0mghii, I was able to get a TWRP backup of the system, boot, and data. I replaced this backup with my own so none of his data (if possible) could be taken advantage of. However, after flashing it, I was still unable to boot up. Here are the steps I took in order to get everything back to working order. Keep in mind this is for WREN, the small version. Some steps may be unnecessary.
1. Boot to TWRP
2. Go to advanced wipe
3. Wipe everything
4. Go to the link below and download the TWRP Backup
5. Create a backup of a small partition (like boot) on your watch to create the folder.
6. Plug watch into PC while in TWRP
7. Go to the watch's internal storage
8. Go to the TWRP folder
9. Go to the subfolder
10. Paste the downloaded backup folder into this folder, this should be with the one you created earlier
11. Restore this backup on your watch, be sure to check all the boxes
12. Reboot to the bootloader
13. Install ADB if you haven't already, I recommend the 15 second one
14. While the watch is in the bootloader and it is plugged in, type the following commands
fastboot erase cache
fastboot erase misc
fastboot reboot
https://drive.google.com/drive/folders/0B_HUnwYIrFskUW10UDZ0dXdHQzg (You might have to download each item and put them in a folder instead, unless I'm oblivious to something, sorry )
After this, your watch should boot up, then power back down, then boot back up again. This will be followed up by the boot animation and go to the welcome screen.
If any of you guys could provide me with the latest stock rom version TWRP backup or a stock recovery.img, it would be greatly appreciated. (Unless June patch is the latest). The recovery would be great no matter what. Getting the stock recovery can be done by typing the following commands into the command prompt on a PC. Hopefully they work. It should be copied onto the /sdcard.
Via adb shell (make sure ADB debugging is on in developer options, then type adb shell in CMD on PC) type: cat/proc/mtd and press enter
You will see which is recovery partition and then type: dd if=/dev/mtd/mtd1 of=/sdcard/recovery.img (note that mtd1 you must replace with number which is recovery partition)
I hope I helped somebody with this. Again, huge thanks to @z0mghii for making this possible. I'm sorry for bad formatting.
I'm really new to this. I'm also by no means a developer/hardcore android person. These commands were all taken from google. I take 0 responsibility for your device being ruined. This is just what worked for me.
Click to expand...
Click to collapse
I spoke just a bit too soon, now it is hanging on that animation with the 4 dots. Any suggestions?
NEVERMIND, I AM UP AND RUNNING!! WOOHOOOO
Related
For all you Shotputterz heres the factory image we've been waiting for
assuming you have debug mode enabled, ADB and fastboot working properly
EDIT 1: REUP'D CWM mod
EDIT 2: reordered process to make more sense
Method:
1. Download the Beta CWM mod from rootzwikis credit to birdman EDIT:REUP'ED http://d-h.st/Fdp
2. Using fastboot, DO NOT FLASH Clockwork mod just use the syntax
"fastboot boot 'File path of clockwork mod image'
Note* this will boot directly into the recovery without permanently writing to the recovery and boot partition on the eMMC on the Nexus Qs board
3. Download the posted CWM factory backup posted
4. make the directory on the device and adb push the backup folder (unzipped) to /sdcard/clockworkmod/backup while in CWM recovery
*The device should show up in "adb devices" while in the CWM recovery*
5. *TEXT WILL BE REALLY SMALL! Now navigate with the Scroll wheel to backups and restore and tap the mute button to select.
*IF SOMETHING IS SELECTED IN ERROR THERE IS NO BACK BUTTON JUST REBOOT AND REDO FASTBOOT BOOT*
6. Now select restore and select the image folder
7.blah blah CWM Freaking MAGIC
8. Your Q is back to factory state
If someone wants to PM me or show me how to package this in a nicer CWM zip to install with a script let me know
http://d-h.st/yeo
*Note* I am NOT responsible if you brick your already bricked Nexus Q*
You sir get a beer, since my 2nd (dev) Q won't arrive until later this week, and mine was a shot put until this post.
If you happen to be in NYC before I move to SF, you get three beers.
Hoppy ones.
I am moving to SF
Did the reflash go smoothly?
fiveipads said:
I am moving to SF
Did the reflash go smoothly?
Click to expand...
Click to collapse
No unfortunately it didn't--I blew away all partitions other than bootloader so I can't, to my knowledge at least, push the zip since I can't adb.
I've got factory recovery, boot, system imgs but the system img won't push out because of fastboot's apparent inability to handle files that large (1GB exactly I believe).
...I guess I have to patiently await my second Q but the point of having two was to *use* one and have one for dev... rather than have one as a heavy reminder of my overzealous endeavors...
Hopefully I can give it more time while on this SF trip...
Boot into the cwm bootloader with fastboot without flashing. Adb will be enabled and you can push files the files while your in adb recovery. Try that and flash it.
Sent from my SPH-D710 using xda app-developers app
Does our Q's have internal memory.. if not wouldn't it be possible to run back up of off otg memory stick if recovery would support it
Sent from my Galaxy Nexus using xda premium
fiveipads said:
Boot into the cwm bootloader with fastboot without flashing. Adb will be enabled and you can push files the files while your in adb recovery. Try that and flash it.
Sent from my SPH-D710 using xda app-developers app
Click to expand...
Click to collapse
The problem I'm having is that ADB is not responding from CWM... at least not on a Windows machine. The drivers are fine as ADB was working in normal mode before my issue sprung up.
EDIT: As suspected Virtual Ubuntu on a Win host didn't see the device, Physical Ubuntu had no issue. NQ reloaded.
fiveipads said:
Boot into the cwm bootloader with fastboot without flashing. Adb will be enabled and you can push files the files while your in adb recovery. Try that and flash it.
Sent from my SPH-D710 using xda app-developers app
Click to expand...
Click to collapse
Can we do this by say pushing the file to the download folder and then installing from zip?
And i know slightly off topic but once we've installed some apks for example, what's currently the best interface to use to navigate through the apps and use them?
How do I make a directory on Nexus Q
fiveipads said:
For all you Shotputterz heres the factory image we've been waiting for
assuming you have debug mode enabled, ADB and fastboot working properly
Method:
1. Download the posted CWM factory backup posted
2. make the directory on the device and adb push the backup folder (unzipped) to /sdcard/clockworkmod/backup
http://d-h.st/yeo
Click to expand...
Click to collapse
In step 2 you say make a directory for the file that is posted below. How do I create a directory on the Nexus Q? Currently my Q is stuck in a bootloop after trying to launch CWM from a Galaxy Nexus. If you could post command codes that would be awesome!
I figured it out. You can just follow step #4 and in CWM you can push the CWM Factory img to the /sdcard/Download/ folder and use CWM to unzip and launch.
Could someone please provide me the beta cwm image for Nexus Q? The links are all circular and point to
http://goo.im/devs/birdman/CWM-steelhead-beta.img
Which is dead...
discoltk said:
Could someone please provide me the beta cwm image for Nexus Q? The links are all circular and point to
http://goo.im/devs/birdman/CWM-steelhead-beta.img
Which is dead...
Click to expand...
Click to collapse
I've been trying to get ahold of this image too! Anyone?? anyone?? Bueller???
WildSatchmo said:
I've been trying to get ahold of this image too! Anyone?? anyone?? Bueller???
Click to expand...
Click to collapse
Me as well...not sure why I got this damn thing...lol
The edit didn't prompt an email to me even though I'm following the thread, so those of you looking for the clockworkmod beta image please take note that OP was kind enough to provide a working link to the image.
Thanks fiveipads!
Can someone post full backup please?
caioketo said:
Can someone post full backup please?
Click to expand...
Click to collapse
The link at the bottom still works for me...
http://d-h.st/yeo
..
ok this is really bothering me, i've restored with this factory image several times, and I have to do it again right now and I cannot seem to push this file folder to /sdcard/clockworkmod/backup
what am i doing wrong..
it should be:
adb push NexusQFactoryImage /sdcard/clockworkmod/backup/ (assuming the file is in same folder as adb which it is)
that's it right.... the extracted folder contents in a folder.. not the zip.. so i dont understand why this is not working. Everytime I go to CWM and try to restore it tells me nothing to restore...
what really bothers me is that i've done this a hundred times, and never had this problem..
UKROB86 said:
ok this is really bothering me, i've restored with this factory image several times, and I have to do it again right now and I cannot seem to push this file folder to /sdcard/clockworkmod/backup
what am i doing wrong..
it should be:
adb push NexusQFactoryImage /sdcard/clockworkmod/backup/ (assuming the file is in same folder as adb which it is)
that's it right.... the extracted folder contents in a folder.. not the zip.. so i dont understand why this is not working. Everytime I go to CWM and try to restore it tells me nothing to restore...
what really bothers me is that i've done this a hundred times, and never had this problem..
Click to expand...
Click to collapse
BUMP.. stuck in CWM unable to get a restorable file.. no idea why...
Download OneClickRestore (it's the factory image straight from Google with the needed fastboot files included)
Extract zip to OneClickRestore
Unplug Nexus Q
Plug in Nexus Q and place hand on it til the leds turn red then remove hand
Launch "flash-all.bat" from the OneClickRestore folder
You may need to do a full reset, it's hit or miss
Another option is push & flash (Nexus Q)uantum Singularity Project RTS ROM from CWM and again may need to hard reset.
RTS is
Based on stock 4.0.4 build IAN67K
Deodexed
Zip aligned
init.d Support
bash support
Busybox updated
Prerooted
Superuser
Updated Keymap (Home=Home, End=Back, Delete=Menu, Insert=Visualizer)
Lokifish Marz said:
Download OneClickRestore (it's the factory image straight from Google with the needed fastboot files included)
Extract zip to OneClickRestore
Unplug Nexus Q
Plug in Nexus Q and place hand on it til the leds turn red then remove hand
Launch "flash-all.bat" from the OneClickRestore folder
You may need to do a full reset, it's hit or miss
Another option is push & flash (Nexus Q)uantum Singularity Project RTS ROM from CWM and again may need to hard reset.
RTS is
Based on stock 4.0.4 build IAN67K
Deodexed
Zip aligned
init.d Support
bash support
Busybox updated
Prerooted
Superuser
Updated Keymap (Home=Home, End=Back, Delete=Menu, Insert=Visualizer)
Click to expand...
Click to collapse
The problem with putting Quantum singularity project on is that I can't turn on ADB debug, because i use a bluetooth mouse and keyboard, don't have an OTG mouse/keyboard, so somehow I need to be able to connect with adb to setup a bluetooth connected mouse/keyboard
I was thinking to install stock image, and then without wiping install Quantum SIngularity Project over top to preserve the settings for usb debug, on.
what's confusing to me is that i've restored the stock image many times before, and never had a problem.. that's why im wondering what the problem is.. if im typing something wrong.
I used the OneClickRestore as you said, and im just booting it up now
EDIT: didn't get past boot logo, i'll try again
So just to confirm this OneClickRestore is loading the stock nexus Q img right? I've never used it before I usually manually do it
EDIT: still stuck at the nexus q logo before home screen
do you see any error in my commands of trying to push the stock img folder (original post) to "/sdcard/clockworkmod/backup" ? I've done it many times before never had a problem
I am very new to the android world, seeing as I am a recent iOS convert. However, I am still struggling with all the terminology and technicalities of android and require assistance (perhaps a lot! :cyclops.
I have managed to root my G2 (VERIZON MODEL) but am stuck there. I do not know how to install CWM or TWRP, nor install any custom ROMs like CM or Gummy.
So will anyone be kind enough to guide me through the process? Thank you.
P.S.
I have searched through the threads in this forum regarding installing custom ROMs and am still confused.
from this thread here
http://forum.xda-developers.com/showthread.php?t=2449670
first download twrp for your device, http://techerrata.com/file/twrp2/g2vzw/openrecovery-twrp-2.6.3.3-g2vzw.zip
plug the phone to the computer, make sure u have usb debugging on in developer settings of phone
since you are already rooted, place that file recovery img to the IOROOT folder.
once done, rename the recovery file to recovery.img
one done, CONTROL + SHIFT + RIGHT CLICK, OPEN COMMAND PROMPT HERE
then type this
adb push recovery.img /data/local/tmp/recovery.img
adb shell
(IF YOU DONT SEE A # prompt on your phone, type su in the command prompt to get it then allow it on phone. once thats done then contine onto next step blow.)
cd /data/local/tmp
dd if=/data/local/tmp/recovery.img of=/dev/block/platform/msm_sdcc.1/by-name/recovery
exit
adb reboot recovery
once its complet just reboot the phone and you should have twrp installed!
once twrp is installed, you can dl the verizon version of paranoid android here
http://downloads.codefi.re/houstonn/kitkat/G2/PA/vs980/pa_g2-4.0-ALPHA-20131205-vs980.zip
and
http://www.androidfilehost.com/?fid=23252070760973599
dl the file, drag the files to the phone, dont place into any folder though.
to install, go to the ioroot folder again, control shift right click open prompt again, type adb reboot recovery
phone should reboot to recovery, go to settings, then select USE RM-F instead of formatting, then go to wipe, advance, select dalvik cache, system, data, and cache. IMPORTANT DO NOT SELECT INTERNAL STORAGE!!!
then swipe to wipe
then go to install then install the paranoid android download first, once its installed, hit the back button on the botom right, then install the GAPPS, then reboot the device your done.
Or you could just download the recovery.img that u choose, and flash it using the app called "Flashify". Easiest way by far and works perfectly for me everytime, using both TWRP and CWM whenever I need.
Once you have that done, installing a ROM such as GUMMY is fairly simple since it usually has the instructions right there in the OP of the thread. Pretty straightforward.
expertzero1 said:
from this thread here
http://forum.xda-developers.com/showthread.php?t=2449670
first download twrp for your device, http://techerrata.com/file/twrp2/g2vzw/openrecovery-twrp-2.6.3.3-g2vzw.zip
plug the phone to the computer, make sure u have usb debugging on in developer settings of phone
since you are already rooted, place that file recovery img to the IOROOT folder.
once done, rename the recovery file to recovery.img
one done, CONTROL + SHIFT + RIGHT CLICK, OPEN COMMAND PROMPT HERE
then type this
adb push recovery.img /data/local/tmp/recovery.img
adb shell
(IF YOU DONT SEE A # prompt on your phone, type su in the command prompt to get it then allow it on phone. once thats done then contine onto next step blow.)
cd /data/local/tmp
dd if=/data/local/tmp/recovery.img of=/dev/block/platform/msm_sdcc.1/by-name/recovery
exit
adb reboot recovery
once its complet just reboot the phone and you should have twrp installed!
once twrp is installed, you can dl the verizon version of paranoid android here
http://downloads.codefi.re/houstonn/kitkat/G2/PA/vs980/pa_g2-4.0-ALPHA-20131205-vs980.zip
and
http://www.androidfilehost.com/?fid=23252070760973599
dl the file, drag the files to the phone, dont place into any folder though.
to install, go to the ioroot folder again, control shift right click open prompt again, type adb reboot recovery
phone should reboot to recovery, go to settings, then select USE RM-F instead of formatting, then go to wipe, advance, select dalvik cache, system, data, and cache. IMPORTANT DO NOT SELECT INTERNAL STORAGE!!!
then swipe to wipe
then go to install then install the paranoid android download first, once its installed, hit the back button on the botom right, then install the GAPPS, then reboot the device your done.
Click to expand...
Click to collapse
So I take it that I put the "ioroot10" file into my phone over the USB, then extract the files of the TWRP file, then place the extracted TWRP file inside of the ioroot10 file? Also, I did the control+shift+right click, but there is not OPEN COMMAND PROMPT option. Sorry for all the questions..
dlee96 said:
So I take it that I put the "ioroot10" file into my phone over the USB, then extract the files of the TWRP file, then place the extracted TWRP file inside of the ioroot10 file? Also, I did the control+shift+right click, but there is not OPEN COMMAND PROMPT option. Sorry for all the questions..
Click to expand...
Click to collapse
no, you place the recovery.img to the ioroot10 folder, ioroot10 stays on your computer.
control + shift + right click = open command window here
Just use flashify its free n so much easier
the definition of open: “mkdir android ; cd android ; repo init -u git:// android.git.kernel.org/platform/manifest.git ; repo sync ; make" gansta mic drop
Hi Guys,
I'm hoping someone can help me here with unbricking my daughters Nabi 2 tablet.
The long story short is that I've tried to update to the latest OTA with TWRP 2.3.3.0 (Nabi 1.9.37) and gapps installed in the past (in order to have google play services).
After downloading the OTA and successfull file verification it booted into TWRP mode and this is when things went wrong...
As I wasn't sure about how to even leave the TWRP mode I have hit few things by accident (I think one of them asked me if I want to wipe my ROM and I said YES + when I was after that trying to reboot the tablet it gave me a warning saying something like "you have no OS installed - are you sure to reboot?).
Now, of course due to my stupid actions it doesn't work - stuck on Nabi boot logo and when I try to pres Volume+ and Power together it gives me the screen with 4 options to choose from (Boot Normally, Fastboot Protocol, Recovery Kernel, Forced Recovery) but I still can't select/move the highlighted item. All what I'm able to do now is to power it off by holding the power button pressed for couple seconds.
Based on your experience here - is there anything that can be done or is it a "real brick" and we need to buy something new for her?
Thank you for any suggestions.
Hi,
I managed to boot into TWRP somehow...
Could someone please direct me how I can re-flash it with a Nabi 2 UK OS (and where I can source the file from if possible at all)?
Cheers,
T1000
termostat1000 said:
Hi,
I managed to boot into TWRP somehow...
Could someone please direct me how I can re-flash it with a Nabi 2 UK OS (and where I can source the file from if possible at all)?
Cheers,
T1000
Click to expand...
Click to collapse
Try sections 9 and 10. http://forum.xda-developers.com/nabi-2/general/nabi-information-t3229119
Hi,
Using NabiLab I managed to load stock 1.9.37 through TWRP.
At the moment tablet will start, let me through the initial setup wizard and go into normal mode from when it was new (no Google services available).
When I try to install gapps (TWRP mode) using NabiLab it goes into endless boot loop showing just a splash screen of the screen lock and reloads again.
I tried also bringing it more to factory condition but it is not recognised in NabiLab when android is fully booted (even though PC can see it). I tried different drivers but without too much luck. When in TWRP mode it comes up as Alcatel ADB Device and when adroid is booted it comes up as a storage device rather than ADB.
I feel I'm pretty close but I need just a hint how to solve it finally without bricking it for real...
Cheers
T
termostat1000 said:
Hi,
Using NabiLab I managed to load stock 1.9.37 through TWRP.
At the moment tablet will start, let me through the initial setup wizard and go into normal mode from when it was new (no Google services available).
When I try to install gapps (TWRP mode) using NabiLab it goes into endless boot loop showing just a splash screen of the screen lock and reloads again.
I tried also bringing it more to factory condition but it is not recognised in NabiLab when android is fully booted (even though PC can see it). I tried different drivers but without too much luck. When in TWRP mode it comes up as Alcatel ADB Device and when adroid is booted it comes up as a storage device rather than ADB.
I feel I'm pretty close but I need just a hint how to solve it finally without bricking it for real...
Cheers
T
Click to expand...
Click to collapse
Pretty hard to brick a Nabi2.
Why did you choose 1.9.37? Isn't the latest 2.3.2 and already has Gapps?
When in Android do you have ADB turned on in Developer options?
Is this the procedure you used?
a) Download the ROM for your device in section 10
b) Boot to TWRP (see above for instructions)
c) Do a backup of just the boot partition in TWRP.
- Click Restore tab
- Just check "boot" and nothing else.
- Swipe to Backup
d) Eject the external SD from the tablet and place in the computer
- Note: You should unmount the card from the mount tab in TWRP before ejecting it. (Uncheck the box next to external SD)
e) Connect the SD card to you computer
f) On the SD card navigate to the folder TWRP/BACKUPS/XXXX. XXX is a serial number unique to your Nabi.
g) Make a new folder and call in whatever you want. So it should now look like TWRP/BACKUPS/XXX/yourfolder
h) Unzip the ROM file you downloaded in to the "yourfolder" you created above. The files should look like ext4.system.win, emmc.boot.win, ext.addon.win, etc. Inside the the "yourfolder" directory.
i) Download the bootloader zip for your device from section 10
j) Copy it to the external SD in a location you will remember. This will be for the bootloader update.
k) Eject the SD card from your computer (safely eject it)
l) Install SD card in Nabi
- After inserted in tablet go to TWRP mount tab and check the box to mount the SD card
m) Go to restore tab, and find the backup under the "yourfolder" you made and unzipped the files to.
n) You should be able to select boot, system, and addon and skip the others.
o) If everything restores then go to TWRP install tab, find the bootloader.zip you downloaded and install it.
p) Reboot
Code:
[U][B]Nabi2 Original United Kingdom (NABI-NV7A-UK)[/B][/U]
Version 2.3.2[URL="https://www.androidfilehost.com/?fid=24269982087011751"] Download[/URL]
ROM Mirror[URL="http://www.nabtabhacks.com/downloads/232UKstock.zip"] Download[/URL]
Bootloader [URL="https://www.androidfilehost.com/?fid=24269982087013995"] Download[/URL]
aicjofs said:
Pretty hard to brick a Nabi2.
Why did you choose 1.9.37? Isn't the latest 2.3.2 and already has Gapps?
When in Android do you have ADB turned on in Developer options?
Is this the procedure you used?
a) Download the ROM for your device in section 10
b) Boot to TWRP (see above for instructions)
c) Do a backup of just the boot partition in TWRP.
- Click Restore tab
- Just check "boot" and nothing else.
- Swipe to Backup
d) Eject the external SD from the tablet and place in the computer
- Note: You should unmount the card from the mount tab in TWRP before ejecting it. (Uncheck the box next to external SD)
e) Connect the SD card to you computer
f) On the SD card navigate to the folder TWRP/BACKUPS/XXXX. XXX is a serial number unique to your Nabi.
g) Make a new folder and call in whatever you want. So it should now look like TWRP/BACKUPS/XXX/yourfolder
h) Unzip the ROM file you downloaded in to the "yourfolder" you created above. The files should look like ext4.system.win, emmc.boot.win, ext.addon.win, etc. Inside the the "yourfolder" directory.
i) Download the bootloader zip for your device from section 10
j) Copy it to the external SD in a location you will remember. This will be for the bootloader update.
k) Eject the SD card from your computer (safely eject it)
l) Install SD card in Nabi
- After inserted in tablet go to TWRP mount tab and check the box to mount the SD card
m) Go to restore tab, and find the backup under the "yourfolder" you made and unzipped the files to.
n) You should be able to select boot, system, and addon and skip the others.
o) If everything restores then go to TWRP install tab, find the bootloader.zip you downloaded and install it.
p) Reboot
Code:
[U][B]Nabi2 Original United Kingdom (NABI-NV7A-UK)[/B][/U]
Version 2.3.2[URL="https://www.androidfilehost.com/?fid=24269982087011751"] Download[/URL]
ROM Mirror[URL="http://www.nabtabhacks.com/downloads/232UKstock.zip"] Download[/URL]
Bootloader [URL="https://www.androidfilehost.com/?fid=24269982087013995"] Download[/URL]
Click to expand...
Click to collapse
Hi aicjofs,
I followed the steps above except step c which I haven't done.
So it looked good with the NabiLab built in 1.9.37 and it seemed to load fine with my TWRP 2.3.3.0 but it was hgoing into this endless boot loop after trying to install gapps. BTW I went for 1.9.37 as it came with NabiLab and turned right.
After your reply I've donwloaded the 232UK stock rom and bootloader. Copied both onto SD card - at that stage it would let me do a restore directly from the SD card so I've copied the 232UK rom into internal memory. Restore process went OK and at the end I've installed its dedicated bootloader...
Right now the situation is that I can only boot into TWRP but restore doesn't show any available roms (both internal or external memory) even though there is backup folder on the SD card.
What worries me the most is when I go to advanced / file manager / sdcard (internal memory) in TWRP mode it doesn't show any files or folders there. When I try to dipslpay tablet information in NabiLab it shows the external SD card properties properly (capacity/free space) but on the internal memory it says "Size df:KB Free can'tKB used find".
Does it mean it has wiped all the internal memory down to zero? Would this be the reason for recovery no being able to identify the roms on external SD card too?
Looking at the log in TWRP mode it is filled with entries like
E:Unable to mount '/data'
E:Unable to mount '/cache'
E:Can't open /cache/recovery/last_install
E:Can't open (No such file or directory)
What a pain is this thing, honestly...
termostat1000 said:
Hi aicjofs,
I followed the steps above except step c which I haven't done.
So it looked good with the NabiLab built in 1.9.37 and it seemed to load fine with my TWRP 2.3.3.0 but it was hgoing into this endless boot loop after trying to install gapps. BTW I went for 1.9.37 as it came with NabiLab and turned right.
After your reply I've donwloaded the 232UK stock rom and bootloader. Copied both onto SD card - at that stage it would let me do a restore directly from the SD card so I've copied the 232UK rom into internal memory. Restore process went OK and at the end I've installed its dedicated bootloader...
Right now the situation is that I can only boot into TWRP but restore doesn't show any available roms (both internal or external memory) even though there is backup folder on the SD card.
What worries me the most is when I go to advanced / file manager / sdcard (internal memory) in TWRP mode it doesn't show any files or folders there. When I try to dipslpay tablet information in NabiLab it shows the external SD card properties properly (capacity/free space) but on the internal memory it says "Size df:KB Free can'tKB used find".
Does it mean it has wiped all the internal memory down to zero? Would this be the reason for recovery no being able to identify the roms on external SD card too?
Looking at the log in TWRP mode it is filled with entries like
E:Unable to mount '/data'
E:Unable to mount '/cache'
E:Can't open /cache/recovery/last_install
E:Can't open (No such file or directory)
What a pain is this thing, honestly...
Click to expand...
Click to collapse
My fault. I forgot to tell you once you update the bootloader you need to use TWRP for Jellybean, you are still using TWRP for Ice Cream Sandwich .
Code:
[B][U]Nabi2 Original (NABI-NV7A)[/U][/B]
Ice Cream Sandwich TWRP 2.6.3[URL="http://forum.xda-developers.com/attachment.php?attachmentid=2586828&d=1392743412"] Download[/URL]
Jellybean TWRP 2.8.5[URL="http://forum.xda-developers.com/attachment.php?attachmentid=3211498&d=1426404068"] Download[/URL]
KitKat TWRP 2.8.7[URL="http://forum.xda-developers.com/attachment.php?attachmentid=3473994&d=1442276115"] Download[/URL]
Discussion Thread [URL="http://forum.xda-developers.com/showthread.php?t=2074501"]Link[/URL]
At that point you can try to restore the 2.3.2 ROM again. Or try the 2.2 ROM http://forum.xda-developers.com/showpost.php?p=50341726&postcount=85
aicjofs said:
My fault. I forgot to tell you once you update the bootloader you need to use TWRP for Jellybean, you are still using TWRP for Ice Cream Sandwich .
Code:
[B][U]Nabi2 Original (NABI-NV7A)[/U][/B]
Ice Cream Sandwich TWRP 2.6.3[URL="http://forum.xda-developers.com/attachment.php?attachmentid=2586828&d=1392743412"] Download[/URL]
Jellybean TWRP 2.8.5[URL="http://forum.xda-developers.com/attachment.php?attachmentid=3211498&d=1426404068"] Download[/URL]
KitKat TWRP 2.8.7[URL="http://forum.xda-developers.com/attachment.php?attachmentid=3473994&d=1442276115"] Download[/URL]
Discussion Thread [URL="http://forum.xda-developers.com/showthread.php?t=2074501"]Link[/URL]
At that point you can try to restore the 2.3.2 ROM again. Or try the 2.2 ROM http://forum.xda-developers.com/showpost.php?p=50341726&postcount=85
Click to expand...
Click to collapse
Forgive me please but I'm not entirely sure how to load this TWRP 2.8.5 for JellyBean on it with TWRP 2.3.3.0 in place..
Cheers
termostat1000 said:
Forgive me please but I'm not entirely sure how to load this TWRP 2.8.5 for JellyBean on it with TWRP 2.3.3.0 in place..
Cheers
Click to expand...
Click to collapse
You will need to use fastboot to load it. If you have a nabilab folder it already has fastboot available. So using the procedure below you couldn't download the ZIP file I linked in post above. Extract the from the zip the recovery.img or twrp-recovery.img and put it in the nabilab folder. (Im puling the procedure from http://forum.xda-developers.com/nabi-2/general/nabi-information-t3229119 )
1) To load TWRP we will be in the fastboot operational mode(see section 3)
Device powered off:
-Depending on device press and hold the power and vol - keys OR power and vol + key. Some will boot straight to recovery, and others will come to the "bootloader" screen. We want the bootloader.
-To enter fastboot use vol+ and vol- to highlight and select fastboot protocol. (Device will need to be plugged in to computer and fastboot driver installed before the screen will change)
Device powered on:
-Use ADB and execute from the command line:
Code:
adb reboot-bootloader
2) USB plugged in and Fastboot/Bootoader Driver loaded(see section 4) verify with windows device manager if needed.
3) Download the TWRP zip file for your device from TWRP list below(see section 8)
4) Extract the file to the location your are running your command prompt(see section 6)
-The file will be called twrp-recovery.img or recovery.img
5) Depending on the name of the file in step 4, load TWRP by typing at the command prompt:
Code:
fastboot flash recovery recovery.img
or
Code:
fastboot flash recovery twrp-recovery.img
aicjofs said:
You will need to use fastboot to load it. If you have a nabilab folder it already has fastboot available. So using the procedure below you couldn't download the ZIP file I linked in post above. Extract the from the zip the recovery.img or twrp-recovery.img and put it in the nabilab folder. (Im puling the procedure from http://forum.xda-developers.com/nabi-2/general/nabi-information-t3229119 )
1) To load TWRP we will be in the fastboot operational mode(see section 3)
Device powered off:
-Depending on device press and hold the power and vol - keys OR power and vol + key. Some will boot straight to recovery, and others will come to the "bootloader" screen. We want the bootloader.
-To enter fastboot use vol+ and vol- to highlight and select fastboot protocol. (Device will need to be plugged in to computer and fastboot driver installed before the screen will change)
Device powered on:
-Use ADB and execute from the command line:
Code:
adb reboot-bootloader
2) USB plugged in and Fastboot/Bootoader Driver loaded(see section 4) verify with windows device manager if needed.
3) Download the TWRP zip file for your device from TWRP list below(see section 8)
4) Extract the file to the location your are running your command prompt(see section 6)
-The file will be called twrp-recovery.img or recovery.img
5) Depending on the name of the file in step 4, load TWRP by typing at the command prompt:
Code:
fastboot flash recovery recovery.img
or
Code:
fastboot flash recovery twrp-recovery.img
Click to expand...
Click to collapse
Hi,
Thank you very much for your help but it clearly looks that this is way beyond my knowledge on how to use all of these fastboot, command, adb and so on...
I regret I ever touched the thing at all.
So there is absolutely no easy way - command line is a must from where I am right now?
termostat1000 said:
Hi,
Thank you very much for your help but it clearly looks that this is way beyond my knowledge on how to use all of these fastboot, command, adb and so on...
I regret I ever touched the thing at all.
So there is absolutely no easy way - command line is a must from where I am right now?
Click to expand...
Click to collapse
Its not a must but easiest to try and walk you through. Which version of Nabilab are you using? You could move some files around and still use Nabilab. Up to you which way to go forward. I'll try and help.
aicjofs said:
Its not a must but easiest to try and walk you through. Which version of Nabilab are you using? You could move some files around and still use Nabilab. Up to you which way to go forward. I'll try and help.
Click to expand...
Click to collapse
Hi,
I'm not so much afraid of copy/paste for cmd... the biggest fear is that I don't know anything about ADB, fasboot etc. So when your instruction in previous post says use ADB and I purely don't know what it means.
I think if the option is there I'd like to ask if you could help with restoring it with Nabilab.
Thanks a million for your help!
T
termostat1000 said:
Hi,
I'm not so much afraid of copy/paste for cmd... the biggest fear is that I don't know anything about ADB, fasboot etc. So when your instruction in previous post says use ADB and I purely don't know what it means.
I think if the option is there I'd like to ask if you could help with restoring it with Nabilab.
Thanks a million for your help!
T
Click to expand...
Click to collapse
Which version of Nabilab are you using? Is it the commandline version. Black window, where you have to use keyboard to make selections?
aicjofs said:
Which version of Nabilab are you using? Is it the commandline version. Black window, where you have to use keyboard to make selections?
Click to expand...
Click to collapse
Hi,
I'm using Nabilab ver 2 - black windows with keyboard made selections.
termostat1000 said:
Hi,
I'm using Nabilab ver 2 - black windows with keyboard made selections.
Click to expand...
Click to collapse
Find the Nabilab folder on your computer. Open the "recovery" folder. Then open the "stock" folder. Inside it there is recovery.img file. Rename it to recoverystock.img.
You downloaded the twrp-recovery-JBNV7AUS.zip from a few posts back. Extract the twrp-recovery.img file and put it in the stock folder. Now rename the twrp-recovery.img file to recovery.img.
Now boot the tablet to TWRP recovery(the one that isn't working) and run Nabilab. Select 4 Install recoveries. Then 4 instal stock recovery. Then reboot in to recovery and see if you have the 2.8.5 recovery
aicjofs said:
Find the Nabilab folder on your computer. Open the "recovery" folder. Then open the "stock" folder. Inside it there is recovery.img file. Rename it to recoverystock.img.
You downloaded the twrp-recovery-JBNV7AUS.zip from a few posts back. Extract the twrp-recovery.img file and put it in the stock folder. Now rename the twrp-recovery.img file to recovery.img.
Now boot the tablet to TWRP recovery(the one that isn't working) and run Nabilab. Select 4 Install recoveries. Then 4 instal stock recovery. Then reboot in to recovery and see if you have the 2.8.5 recovery
Click to expand...
Click to collapse
Great!
Your trick worked fine and now I can see TWRP 2.8.5.0 and I have problems with drivers - keeps failing to recognize the tablet.
I'll work on the driver issue or is there something I should know about it with TWRP 2.8.5.0 lodaed?
What is my next step from here as Android is still stuck on Nabi logo (no motion) and I'm afraid to do anything in case I create even bigger mess than I already have
I also noticed when I try to shut it down from inside TWRP it asks me a question if I want to root the tablet (Install super SU) - is it something I should do and at what stage?
Thanks!
T
termostat1000 said:
Great!
Your trick worked fine and now I can see TWRP 2.8.5.0 and I have problems with drivers - keeps failing to recognize the tablet.
I'll work on the driver issue or is there something I should know about it with TWRP 2.8.5.0 lodaed?
What is my next step from here as Android is still stuck on Nabi logo (no motion) and I'm afraid to do anything in case I create even bigger mess than I already have
I also noticed when I try to shut it down from inside TWRP it asks me a question if I want to root the tablet (Install super SU) - is it something I should do and at what stage?
Thanks!
T
Click to expand...
Click to collapse
If you can see the files again now with the correct TWRP. You can try to restore the 2.3.2 ROM again. Or maybe try the procedure from post #5 with the 2.2 ROM I linked to in post #7. You don't have to do the bootloader install anymore so skip that step. Installing root doesn't matter, you can choose to install or not.
aicjofs said:
If you can see the files again now with the correct TWRP. You can try to restore the 2.3.2 ROM again. Or maybe try the procedure from post #5 with the 2.2 ROM I linked to in post #7. You don't have to do the bootloader install anymore so skip that step. Installing root doesn't matter, you can choose to install or not.
Click to expand...
Click to collapse
You're a STAR!
All happy working as new with 232UK ROM and bootloader loaded with your instructions.
I'd never get this sorted without your specialized help.
If I only could I'd send you something just to say Thank You...
T - Happy Dad of Amelia
termostat1000 said:
You're a STAR!
All happy working as new with 232UK ROM and bootloader loaded with your instructions.
I'd never get this sorted without your specialized help.
If I only could I'd send you something just to say Thank You...
T - Happy Dad of Amelia
Click to expand...
Click to collapse
Your thanks is enough Glad we got it sorted and a happy kid!
I tried to root my watch a while back and kind of gave up. Since then, I have installed both the stock recovery and system image found in this thread:
https://forum.xda-developers.com/zenwatch-2/general/m6e69n-twrp-backup-stock-boot-firmware-t3484961
Now, I keep getting the update to M6E69X and it goes through the normal process of updating, but then a picture of an Android with an exclamation point comes up. I'm almost positive that its similar to the issues of newer versions of Android on phones requiring complete stock systems to update. The only problem is, I have tried reflashing the backup in the link above about four times now and it still won't work.
Any help will be appreciated at all and I'm sorry if this has been answered before and I'm just blind.
About 4 down from your post, https://forum.xda-developers.com/zenwatch-2/help/m6e69x-stock-rom-t3564626
At the bottom of that thread is a zipped up TWRP backup. Get TWRP temporarily running on the watch and restore it from there.
Here are the brief steps I did.
1. Get ADB Minimal and Fastboot - plug your watch into the computer using the cord. Enable ADB debugging on the watch.
2. Get twrp-v3.0.0-0.jk-v3.recovery.img for the watch
3. Fastboot oem unlock (erases your /data partition)
4. fastboot boot twrp-v3.0.0-0.jk-v3.recovery.img
5. Make an initial backup of the watch. You'll need the file structure created.
5. TWRP should let you copy the files to/from the watch
6. Create a new folder and copy the files from the zip to a folder under the serial number folder below TWRP - I have folder called 2017-03-14--11-51-50_M6E69X
7. Restore that copied TWRP backup
Hope that helps.
OK to start off this thread is meant to continue the work done in the thread here huawei-ascend-xt2-h1711 their were some good people working on stuff their but most seem to have moved on.
I decided to pick up the Elate this week from Best Buy and thought it might be time to start a new thread on rooting and restoring the Cricket version of this phone.
Rooting the H1711z Huawei Elate
First step is to unlock your bootloader at Huawei here > https://emui.huawei.com/en/unlock_detail
Well it seems Huawei is no longer unlocking the bootloader so you need to pay DC Unlocker to unlock your bootloader
follow the instructions posted here >> https://forum.xda-developers.com/honor-7x/how-to/how-to-unlock-huawei-bootloader-removal-t3780903
Also please make a backup of your own boot.img as soon as you flash TWRP before flashing the patched _boot.img provided
~Huge thanks to @aslezak for these instructions~
Root instructions: (I used Magisk Manager v5.5.3 boot.img patching to create the boot.img)
here is the stock boot.img for the Elate H1711z
I am not responsible if you brick your device. I didn't brick mine, but if you don't type the correct commands you could be in trouble
Copy this patched_boot.zip to your sdcard. You can download it from the device directly if that's easier. Insert the sdcard into the phone if it wasn't there already (e.g. if you downloaded from a computer).
Reboot phone into fastboot. The easiest way is, if phone is on, unplug phone from USB, hold power button / select "Power Off". Hold VolDown+Power. Phone will boot into fastboot mode.
(skip this step if you've already flashed TWRP) Flash TWRP into your recovery partition. The link was provided in an earlier post by yuweng twrp-xt2-v3.img
plug usb cable in (from phone to computer). From your computer / cmd.exe window, cd \adb:
fastboot devices #make sure computer adb/fastboot sees your device
fastboot flash recovery twrp_xt2_v3.img
Boot into TWRP. From the above step, you should "fastboot reboot", immediately unplug phone from USB, then
With the phone unplugged from the computer, hold VolUp+Power. Release power after the device reboots. It might take a couple tries .. select reboot from eRecovery if that starts instead. Alternatively you can boot into recovery through adb via "adb reboot recovery".
Tap "Keep Read Only" when TWRP starts.
Tap "Install", then tap "Install Image" at the bottom. Browse (Up a Level) then "external_sd"
If you unzipped the patched_boot.zip you will see patched_boot.img here. Select it.
Select "boot" (uncheck "recovery") partition to flash.
Swipe to confirm Flash
Tap "Reboot" once it's completed.
You should be rooted!
Note: if Magisk Manager does not appear in your list of installed applications, download & install it from here latest Magisk Manager. Without this, you won't be prompted to allow root!
Click to expand...
Click to collapse
Note: Magisk Manager will update you to version 16 on first run, it's OK to update in fact feel free to flash it in recovery before you reboot if you want it.
A couple notes about twrp_xt2_v3.img
when you start TWRP choose keep system read only - Unless your planing to restore a backup then choose to make system writable
You cannot backup or restore /data (it's encrypted so don't even try)
Do not use Wipe / factory reset or format data unless you have a good working backup of your userdata partition that you dd to your external_sd yourself see below
From TWRP / adb shell
paste these commands
dd if=/dev/block/bootdevice/by-name/userdata | bzip2 -9f > /external_sd/userdata.img.bz2
to restore--> bzip2 -dc /external_sd/userdata.img.bz2 | dd of=/dev/block/bootdevice/by-name/userdata
dd if=/dev/block/bootdevice/by-name/system | bzip2 -9f > /external_sd/system.img.bz2
to restore--> bzip2 -dc /external_sd/system.img.bz2 | dd of=/dev/block/bootdevice/by-name/system
again thanks go to aslezak
When choosing a backup always prefer the image instead of the stock files (system image - custom image - vendor image are best )(Never choose both system and system image at the same time it's too big and a waste of time and space)
when you exit TWRP do not choose to install the twrp app
Also be sure and thank aslezak for his post here > https://forum.xda-developers.com/showpost.php?p=75115521&postcount=286
Notes on booting up the phone (from power off)
Bootloader (fastboot) = power + volume down + USB hooked to pc
eRecovery = power + volume up + USB hooked to PC
TWRP = power + volume up
Restoring your phone to Stock
We now have the B120 Stock dload update See here >> https://forum.xda-developers.com/showthread.php?p=76902495&highlight=dload#post76902495
I've created a Stock Rom to easily return your phone to Stock Factory Settings (b120)
Warning this will completely Wipe your phoneTo Install
1) Download and copy the H1711z_stock_ROM_v2.zip to your external_sd
2) Boot to TWRP recovery
3) Go to Settings check Use rm -fr instead of formatting / Wipe / Format Data / Type "yes" to confirm
4) Choose Home / Install /Select storage Micro sd / H1711z_stock_ROM_v2.zip / swipe to install
5) when it finishes choose the wipe cache button and then reboot and choose Do not Install
Your phone is now back to stock
Extra's By Request
Here's the XT2_Stock_Rom and XT2_Magisk_ Rom here > https://androidfilehost.com/?w=files&flid=266256
If you like to try my CleanRom for the Elate I uploaded it here >> Elate.CleanRom.v2.zip
flashing instructions are the same as the stock file above
here's whats added/removed
Apps deleted from /Data/hwinit/:
Google Editor Slides
Google Editor Sheets
Google Editor Docs
Apps deleted from Cust:
the entire h1711 folder
AT&T Remote Support
myAT&T
AT&T Visual Voicemail
AT&T Hot Spots
Google Talkback
OMACP
Apps deleted from System:
Amazon shopping
App select
Call Protect
CricketWiFiManager
Device Help
Deezer
Facebook
Facebook App Installer
Facebook app manager
Gmail
Google Duo
Google Chrome
Google Drive
Google Maps
Google Play Photos
Google Play Video
Google Play Music
Google Text to Speech Engine
Ignite
Lookout
myCricket
Protect Plus
Setup & Transfer
Added
FX Root File Manager (as a system App)
Magisk V16 (as a system App)
QuickBoot Reboot (as a system App)
I didn't include Xposed because it's useless without a decrypted Data partition
Note: To remove the Cricket bootanimation, use the FX File Manager with root permission and rename
..\system\version\special_cust\H1711z\cricket\us\media\bootanimation.zip" to bootanimation.zi_ and reboot
I got tired of seeing the error in twrp_v3 about not mounting patch_hw and fixed it ->> Here
you can unzip it and flash it to recovery with TWRP or fastboot
NOTE: added by scrungydoolittle I had a problem with the bz2 image. I prefer to not run it through bz2
dd if=/dev/block/bootdevice/by-name/userdata /external_sd/userdata.img
to restore--> dd if=/external_sd/userdata.img of=/dev/block/bootdevice/by-name/userdata
dd if=/dev/block/bootdevice/by-name/system /external_sd/system.im
to restore--> dd if= /external_sd/system.img of=/dev/block/bootdevice/by-name/system
Of course, the downside is you need a fairly large external sd card.
@scrungydoolittle Please edit you post and remove the Quote of the first post
also the file you posted is not for this phone please remove the link
as to you having problems with the bz2 image they work fine if you follow the instructions
I instructed the user to create their OWN backup of userdata before they format / wipe their data partition
this file most likely contains the users IMEI and should not be shared.
clsA said:
@scrungydoolittle Please edit you post and remove the Quote of the first post
also the file you posted is not for this phone please remove the link
as to you having problems with the bz2 image they work fine if you follow the instructions
I instructed the user to create their OWN backup of userdata before they format / wipe their data partition
this file most likely contains the users IMEI and should not be shared.
Click to expand...
Click to collapse
O.k. I removed the link. It was for the H1711 AT&T phone as it turns out.
And I don't think that image has the IMEI in it, because it is clearly the /system image, and I don't think that data is stored in that partition.
Otherwise all of the posted system images would have the same issue...
scrungydoolittle said:
O.k. I removed the link. It was for the H1711 AT&T phone as it turns out.
And I don't think that image has the IMEI in it, because it is clearly the /system image, and I don't think that data is stored in that partition.
Otherwise all of the posted system images would have the same issue...
Click to expand...
Click to collapse
Thanks ...yeah the userdata contains the IMEI not the system.img
Sent from my LG-H910 using Tapatalk
I would not share a userdata backup unless it was after a factory reset and before I entered any personal account information or data. Agree with you on that
I'd love to see a reliable reference that says userdata contains the IMEI or if you know specifically where it's stored, because l thought IMEI is stored in a totally different partition.
clsA said:
Thanks ...yeah the userdata contains the IMEI not the system.img
Sent from my LG-H910 using Tapatalk
Click to expand...
Click to collapse
divineBliss said:
I would not share a userdata backup unless it was after a factory reset and before I entered any personal account information or data. Agree with you on that
I'd love to see a reliable reference that says userdata contains the IMEI or if you know specifically where it's stored, because l thought IMEI is stored in a totally different partition.
Click to expand...
Click to collapse
IMEI is stored in data/data/com.android.phone
Thank you
Found the IMEI in
/data/data/com.android.phone/shared_prefs/
com.android.phone_preferences.xml on my H1611 after your post.
I'm guessing the IMEI is copied from another partition, but the fact that it's in /data is news to me.
I wonder if the IMEI is in the above file after a factory reset , but I'm not planning to find out anytime soon .
People, be careful sharing your userdata partition backups and other sensitive data containing partition backups out there - unless of course you don't give a crap about security - which you should preface up front so as to not mislead uninformed people of the risks involved in sharing those sensitive data partitions.
clsA said:
IMEI is stored in data/data/com.android.phone
Click to expand...
Click to collapse
It sure would be nice to get one of these stock flash zip's for the H1711 XT2. Would this zip work on it?
clsA said:
Restoring your phone to Stock
I've created a Stock Rom to easily return your phone to Stock Factory Settings (b120)
Warning this completely Wipe your phoneTo Install
1) Download and copy the H1711z_stock_ROM_v2.zip to your external_sd
2) Boot to TWRP recovery
3) Go to Settings check Use rm -fr instead of formatting / Wipe / Format Data / Type "yes" to confirm
4) Choose Home / Install /Select storage Micro sd / H1711z_stock_ROM_v2.zip / swipe to install
5) when it finishes choose the wipe cache button and then reboot and choose Do not Install
Your phone is now back to stock
Click to expand...
Click to collapse
freedomwarrior said:
It sure would be nice to get one of these stock flash zip's for the H1711 XT2. Would this zip work on it?
Click to expand...
Click to collapse
Nice.
What partitions does this install?
And can you make this for the H1711 At&T phone?
freedomwarrior said:
It sure would be nice to get one of these stock flash zip's for the H1711 XT2. Would this zip work on it?
Click to expand...
Click to collapse
No don't use this on the XT2
I / you need system/boot/recovery/ and cust.img files from a XT2 to build it.
Sent from my LG-H910 using Tapatalk
clsA said:
No don't use this on the XT2
I / you need system/boot/recovery/ and cust.img files from a XT2 to build it.
Sent from my LG-H910 using Tapatalk
Click to expand...
Click to collapse
If I send you (or point you to )
system
boot
recover
and cust images could you create one?
The image for system is available, a patched bootloader that installs magisk, an unpatched boot loader, the recovery and e recovery are the same.
I'd like to see 2 flashable zips.
1. that does stock
2. that installs twrp and magisk.
I have all those, but I'm not sure how to make the zip. Is it simply a matter of opening it in a zip prgram and replacing the mentioned image files
with appropriate ones?
scrungydoolittle said:
If I send you (or point you to )
system
boot
recover
and cust images could you create one?
The image for system is available, a patched bootloader that installs magisk, an unpatched boot loader, the recovery and e recovery are the same.
I'd like to see 2 flashable zips.
1. that does stock
2. that installs twrp and magisk.
I have all those, but I'm not sure how to make the zip. Is it simply a matter of opening it in a zip prgram and replacing the mentioned image files
with appropriate ones?
Click to expand...
Click to collapse
I have the Stock system.img and erecovery.img
put the others in a google drive and I'll build them
clsA said:
I have the Stock system.img and erecovery.img
put the others in a google drive and I'll build them
Click to expand...
Click to collapse
Here is the cust.img I just pulled from my XT2 using the dd command.
https://drive.google.com/open?id=1euUHZiJrzfyUVNqgOT76rTk45clPwv9F
Here is a copy of the stock boot I have had sitting on my hard drive.
https://drive.google.com/open?id=1-dAJuwgYdM9F3fBn4dU3x9s74SucocBP
And here is a copy of patched boot (with magisk) if you need it.
https://drive.google.com/open?id=1Tfb7zkcX6auoYEVnMLKDN6tibfzHSPEW
And thank you in advance for doing this! :good:
freedomwarrior said:
Here is the cust.img I just pulled from my XT2 using the dd command.
https://drive.google.com/open?id=1euUHZiJrzfyUVNqgOT76rTk45clPwv9F
Here is a copy of the stock boot I have had sitting on my hard drive.
https://drive.google.com/open?id=1-dAJuwgYdM9F3fBn4dU3x9s74SucocBP
And here is a copy of patched boot (with magisk) if you need it.
https://drive.google.com/open?id=1Tfb7zkcX6auoYEVnMLKDN6tibfzHSPEW
And thank you in advance for doing this! :good:
Click to expand...
Click to collapse
Files are uploading now > https://www.androidfilehost.com/?w=files&flid=257749
Instructions are the same
Backup anything on internal storage it will be wiped
To Install
1) Download and copy the Rom to your external_sd
2) Boot to TWRP recovery
3) Go to Settings check Use rm -fr instead of formatting / Wipe / Format Data / Type "yes" to confirm
4) Choose Home / Install /Select storage Micro sd / your_rom.zip / swipe to install
5) when it finishes choose the wipe cache button and then reboot and choose Do not Install
Your phone is now back to stock
Click to expand...
Click to collapse
after flashing the Magisk rom install the magisk manager and update to v16 (or whatever the newest is)
Awesome! Thank you so much for these. They will definitely come in handy! Much Appreciated!! :good::
clsA said:
OK to start off this thread is meant to continue the work done in the thread here huawei-ascend-xt2-h1711 their were some good people working on stuff their but most seem to have moved on.
Does this wipe out the recovery, and relock the bootloader, or will the bootloader remain unlocked, and twrp remain in place?
Thanks for the XT2 versions.
I decided to pick up the Elate this week from Best Buy and thought it might be time to start a new thread on rooting and restoring the Cricket version of this phone.
Rooting the H1711z Huawei Elate
First step is to unlock your bootloader at Huawei here > https://hwid5.vmall.com/CAS/portal/...ndex&loginChannel=22000000&reqClientType=2023
Also please make a backup of your own boot.img as soon as you flash TWRP before flashing the patched _boot.img provided
~Huge thanks to @aslezak for these instructions~
Note: Magisk Manager will update you to version 16 on first run, it's OK to update in fact feel free to flash it in recovery before you reboot if you want it.
A couple notes about twrp_xt2_v3.img
when you start TWRP choose keep system read only - Unless your planing to restore a backup then choose to make system writable
You cannot backup or restore /data (it's encrypted so don't even try)
Do not use Wipe / factory reset or format data unless you have a good working backup of your userdata partition that you dd to your external_sd yourself see below
From TWRP / adb shell
paste these commands
dd if=/dev/block/bootdevice/by-name/userdata | bzip2 -9f > /external_sd/userdata.img.bz2
to restore--> bzip2 -dc /external_sd/userdata.img.bz2 | dd of=/dev/block/bootdevice/by-name/userdata
dd if=/dev/block/bootdevice/by-name/system | bzip2 -9f > /external_sd/system.img.bz2
to restore--> bzip2 -dc /external_sd/system.img.bz2 | dd of=/dev/block/bootdevice/by-name/system
again thanks go to aslezak
When choosing a backup always prefer the image instead of the stock files (system image - custom image - vendor image are best )(Never choose both system and system image at the same time it's too big and a waste of time and space)
when you exit TWRP do not choose to install the twrp app
Also be sure and thank aslezak for his post here > https://forum.xda-developers.com/showpost.php?p=75115521&postcount=286
Notes on booting up the phone (from power off)
Bootloader (fastboot) = power + volume down + USB hooked to pc
eRecovery = power + volume up + USB hooked to PC
TWRP = power + volume up
Restoring your phone to Stock
I've created a Stock Rom to easily return your phone to Stock Factory Settings (b120)
Warning this will completely Wipe your phoneTo Install
1) Download and copy the H1711z_stock_ROM_v2.zip to your external_sd
2) Boot to TWRP recovery
3) Go to Settings check Use rm -fr instead of formatting / Wipe / Format Data / Type "yes" to confirm
4) Choose Home / Install /Select storage Micro sd / H1711z_stock_ROM_v2.zip / swipe to install
5) when it finishes choose the wipe cache button and then reboot and choose Do not Install
Your phone is now back to stock
By request I have also added the XT2_Stock_Rom and XT2_Magisk_ Rom here > https://www.androidfilehost.com/?w=files&flid=257749
Click to expand...
Click to collapse
Does this wipe out the recovery, and relock the bootloader, or will the bootloader remain unlocked, and twrp remain in place?
Thanks for the XT2 versions.
scrungydoolittle said:
Does this wipe out the recovery, and relock the bootloader, or will the bootloader remain unlocked, and twrp remain in place?
Thanks for the XT2 versions.
Click to expand...
Click to collapse
Really ?? You quoted the first post again
Flashing a Rom will never relock your bootloader
All 3 roms wipe TWRP
Sent from my LG-H910 using Tapatalk
@scrungydoolittle,
I was going to say the same.. .. The reason for clsAs comment is.. .
It's considered bad practice to post the OP or any other long posts unnecessarily. It makes it extremely difficult and annoying for others to wade past the huge quoted post to see what you said.
You can just quote the relevant part of a post (as I did below), refer to post 1 as the OP, or put a link to the post you are referring to.
Hopefully this explanation will get you to edit your last post and reconsider quoting long posts in the future.
Thanks
PS: Consider the fact that some of us read forums via email, XDA forum app, and browsers on mobile devices which have limited screen real estate and require more scrolling than a large desktop monitor.
clsA said:
Really ?? You quoted the first post again
...
Click to expand...
Click to collapse
I'm hoping for some help in rooting my Elate. I was able to get the unlock code from Huawei. I downloaded the ADB and Fastboot drivers from the Android Tutorials page.
ADB recognizes my device when in normal mode. But when I reboot into Bootloader mode, the device is not recognized. It does not show up in Windows device manager and the command "adb devices" is null. I can't get past this point which is clearly a driver problem.
I also have installed and uninstalled Hi-suite a number of times.
Does anyone have any advice? Thanks.