Related
PLEASE! I need to load a new ROM into my MT6575 phone using Smart Phone Flash tool.
I've installed the Mediatek drivers on 4 different computers in my house (Vista, Window 7, Windows 7 64bit, Windows 8) and I cant get ANY of them to work!!
When I look under Ports (COM and LPT) in Device Manager, I ALWAYS get: This device cannot start. (Code 10)
WHAT is going on!! I've wasted so much time with this problem.
johnnysnavely said:
PLEASE! I need to load a new ROM into my MT6575 phone using Smart Phone Flash tool.
I've installed the Mediatek drivers on 4 different computers in my house (Vista, Window 7, Windows 7 64bit, Windows 8) and I cant get ANY of them to work!!
When I look under Ports (COM and LPT) in Device Manager, I ALWAYS get: This device cannot start. (Code 10)
WHAT is going on!! I've wasted so much time with this problem.
Click to expand...
Click to collapse
your not the only one with this problem i have it too with same mt6575 someone help please
Need to uninstall device and reinstall drivers
If you google, "Code 10", you will find that on a Windows system it is an error code generated by the Device Manager "because it can not start a device". In a nut shell, the most likely cause for this is because the device was not properly installed with the right drivers.
If you are running Windows, you can try to use the attached file called USBReview to see what device that is as you know it is your phone. Basically, with this program you can remove all the old drivers and start all the driver installation again.
Try to find your phone either here on xda, on the web or contact your phone's manufacturer - you need drivers!!!
Good luck, Mr. Phelps.
johnnysnavely said:
PLEASE! I need to load a new ROM into my MT6575 phone using Smart Phone Flash tool.
I've installed the Mediatek drivers on 4 different computers in my house (Vista, Window 7, Windows 7 64bit, Windows 8) and I cant get ANY of them to work!!
When I look under Ports (COM and LPT) in Device Manager, I ALWAYS get: This device cannot start. (Code 10)
WHAT is going on!! I've wasted so much time with this problem.
Click to expand...
Click to collapse
ronbo76 said:
If you google, "Code 10", you will find that on a Windows system it is an error code generated by the Device Manager "because it can not start a device". In a nut shell, the most likely cause for this is because the device was not properly installed with the right drivers.
If you are running Windows, you can try to use the attached file called USBReview to see what device that is as you know it is your phone. Basically, with this program you can remove all the old drivers and start all the driver installation again.
Try to find your phone either here on xda, on the web or contact your phone's manufacturer - you need drivers!!!
Good luck, Mr. Phelps.
Click to expand...
Click to collapse
Your USB program does give a lot of information I have never seen before, but I still haven't been able to figure out how to get the driver to load.
thanks, John
I'm having the same problem installing the MT6575 USB VCOM drivers. Is there a workaround to get this installed? I"m using WIN 6 64bit
johnnysnavely said:
PLEASE! I need to load a new ROM into my MT6575 phone using Smart Phone Flash tool.
I've installed the Mediatek drivers on 4 different computers in my house (Vista, Window 7, Windows 7 64bit, Windows 8) and I cant get ANY of them to work!!
When I look under Ports (COM and LPT) in Device Manager, I ALWAYS get: This device cannot start. (Code 10)
WHAT is going on!! I've wasted so much time with this problem.
Click to expand...
Click to collapse
This is what worked for me after lot of experimenting and searching:
- get MTK6575 drivers (for instance from Bruno Martins where he writes about flashing mtk6575 - google: MT6575 flashing tutorial bruno
- Start c/windows/system32/hdwwiz.exe (as admin)
- Click next
- Manually select hardware
- List all devices
- Select the driver (for example usb2ser_Win764.inf)
- from the List select "MediaTek Preloader USB VCOM Port"
(or you can install other drivers from the list if Preloader is not enough..)
On another computer I solved it by installing whole Android SDK, checked my android system and installed updated for SDK (approx. 2 GB) and it installed correct drivers automatically.
Also you can experiment with using another usb port..
Please write here if it helped.
ivy13 said:
This is what worked for me after lot of experimenting and searching:
- get MTK6575 drivers (for instance from Bruno Martins where he writes about flashing mtk6575 - google: MT6575 flashing tutorial bruno
- Start c/windows/system32/hdwwiz.exe (as admin)
- Click next
- Manually select hardware
- List all devices
- Select the driver (for example usb2ser_Win764.inf)
- from the List select "MediaTek Preloader USB VCOM Port"
(or you can install other drivers from the list if Preloader is not enough..)
On another computer I solved it by installing whole Android SDK, checked my android system and installed updated for SDK (approx. 2 GB) and it installed correct drivers automatically.
Also you can experiment with using another usb port..
Please write here if it helped.
Click to expand...
Click to collapse
Tried your first method but still get Code 10 error. Could not understand your second method. Please help. Me device is Qmobile Noir A2
hye.. any progress? am having the same issue.. just for MTK6575 com port driver
Just made my Amoi N820 work
So happy
You get Code 10 becouse your windows couldn't recognize the driver but that's irrelevant becouse flashing will work
No solution?
Any solution on this problem?
I've this china mt6575 galaxy s3 clone and got rooted using CF Root.Got ADB composite driver successfully installed in my pc (using win7 32-bit).When I install preloader usb vcom driver, i'm also facing this 'code 10' issue.Until now I can't install CWM in my phone.(the Flash Tool cannot detect my device).i try to install/push CWM using Terminal Emulator but nothing seems to change .when reboot into recovery mode the same stock recovery appear.Any help please?
orion~X said:
Any solution on this problem?
I've this china mt6575 galaxy s3 clone and got rooted using CF Root.Got ADB composite driver successfully installed in my pc (using win7 32-bit).When I install preloader usb vcom driver, i'm also facing this 'code 10' issue.Until now I can't install CWM in my phone.(the Flash Tool cannot detect my device).i try to install/push CWM using Terminal Emulator but nothing seems to change .when reboot into recovery mode the same stock recovery appear.Any help please?
Click to expand...
Click to collapse
i have thet problem to.
is ther solution?
I HAVE SOLUTION FOR THIS PROBLEM!!
Just ignore the error Code 10! Start the SPFlashtool and load the scatterfile, click on download and connect your switch off Phone with the computer. It will work fine.
Having the Same Problem
I understand I can ignore it and it works on that part, however I'm trying to root my phone now and it's not recognising that I have attached a device to the computer. Please need help to solve the problem. Have the drivers but can't get it without code 10
Hi.
me test for me not work.
iphone 4s.
plz help me.
hihi2u2 said:
I understand I can ignore it and it works on that part, however I'm trying to root my phone now and it's not recognising that I have attached a device to the computer. Please need help to solve the problem. Have the drivers but can't get it without code 10
Click to expand...
Click to collapse
Did you ever get this problem solved as I have the same issue with an MTK 6592 chip based phone?
I have the same problem too.
Installation of Media Tek preloaded drivers gives me Code 10 error.
Has anyone found the solution?
my phone is totally dead without power now after I tried to flash with SP Flash tool using correct ROM. I noticed in device manager that there is a CODE 10 error in mediatek preloader usb driver.. is this the culprit? my phone can no longer be detected now in SPFlash or MTK Droid tools... so hopeless... this is a brandnew phone I bought to be given as gift to my cousin...
I did it! I did it! I did it!
The solution is... we need not MediaTek USB VCOM (Android) (USB\VID_0BB4&PID_0005&MI_02), but PreLoader USB VCOM Port (USB\Vid_0e8d&Pid_2000) !
I have MTK6582 (KingSing S2), the host - WinXPx64.
It looks like my phone (and, maybe, other MTK devices too) have several engineering modes.
I have spent several hours trying to get working VID_0BB4&PID_0005&MI_02, which is exposed, if device is turned on while holding VOL- pressed. In this mode some strange factory mode with nonfunctional menu items is displayed on the screen. But to activate mode with Vid_0e8d&Pid_2000 some trickery is necessary.
Sometimes this USB interface starts repeatedly to appear and disappear every half-second in infinitive loop. I had such situation once, when connected turned off phone to USB cable with battery removed.
I just literally catched MT65xx Preloader by double clicking on it in windows device manager and pressing "install drivers" in it's properties. I have used Driver_Auto_Installer_v1.1236.00\SmartPhoneDriver\x64\Infs\usbvcom.inf from http://spflashtool.com/download/Driver_Auto_Installer_v1.1236.00.zip. DriverVer = 12/24/2011, 2.0000.0.0
After clicking "Read Back" in Flash Tool this insane loop stopped and program started to function as intended.
This interface could also appear once and for very short moment, if turned off phone (with battery inserted) is just connected to host. Also it could be seen again, if power button is pressed. If "Download" or "Read Back" is not pressed in advance in Flash Tool, than boot will continue after smaller than a second pause (if device is functional).
I don't know if running Install.bat (from archive I have given above) is necessary. It didn't installed driver when Vid_0e8d&Pid_2000 wasn't active, but, I guess, running it during short blinks would give the same effect.
Also, I don't know, if advice given in comment#6 in this thread four years ago would work. Maybe, the fault was in older version of driver (DriverVer=05/30/2011,1.1123.0).
Another reason could be that necessary USB interface disappears before windows manages to install driver for it for the first time. Possibly, only if "catched" in device manager, user could manually assign driver to it.
I've been struggling with my UMI Rome for days. It has/had the black screen problem, sometimes won't enter recovery mode, sometimes wouldn't allow charge, sometimes works just fine (yesterday). Last night i mistakenly cut off power during a battery recharge. -- today it has all the above problems (bricked) so I am trying doing a flashing again using the tutorials and tools on the Tehnotone.com site. Sintetix's reply above helps me at least have a better clue on what is going on. Wish me luck! BTW, I am using a Dell Windows 10 pc. (Results to be reported here.)
Sintetix said:
The solution is... we need not MediaTek USB VCOM (Android) (USB\VID_0BB4&PID_0005&MI_02), but PreLoader USB VCOM Port (USB\Vid_0e8d&Pid_2000) !
I have MTK6582 (KingSing S2), the host - WinXPx64.
It looks like my phone (and, maybe, other MTK devices too) have several engineering modes.
I have spent several hours trying to get working VID_0BB4&PID_0005&MI_02, which is exposed, if device is turned on while holding VOL- pressed. In this mode some strange factory mode with nonfunctional menu items is displayed on the screen. But to activate mode with Vid_0e8d&Pid_2000 some trickery is necessary.
Sometimes this USB interface starts repeatedly to appear and disappear every half-second in infinitive loop. I had such situation once, when connected turned off phone to USB cable with battery removed.
I just literally catched MT65xx Preloader by double clicking on it in windows device manager and pressing "install drivers" in it's properties. I have used Driver_Auto_Installer_v1.1236.00\SmartPhoneDriver\x64\Infs\usbvcom.inf from http://spflashtool.com/download/Driver_Auto_Installer_v1.1236.00.zip. DriverVer = 12/24/2011, 2.0000.0.0
After clicking "Read Back" in Flash Tool this insane loop stopped and program started to function as intended.
This interface could also appear once and for very short moment, if turned off phone (with battery inserted) is just connected to host. Also it could be seen again, if power button is pressed. If "Download" or "Read Back" is not pressed in advance in Flash Tool, than boot will continue after smaller than a second pause (if device is functional).
I don't know if running Install.bat (from archive I have given above) is necessary. It didn't installed driver when Vid_0e8d&Pid_2000 wasn't active, but, I guess, running it during short blinks would give the same effect.
Also, I don't know, if advice given in comment#6 in this thread four years ago would work. Maybe, the fault was in older version of driver (DriverVer=05/30/2011,1.1123.0).
Another reason could be that necessary USB interface disappears before windows manages to install driver for it for the first time. Possibly, only if "catched" in device manager, user could manually assign driver to it.
Click to expand...
Click to collapse
I tried what you said. It wouldn't install properly. It kept saying error (code 10) and showed in device management with a caution sign every time I installed the driver. I disabled the forced driver signature thingamabop but it still does it. I guess I'm screwed. Has anyone else fixed this?
Hi all...
I received my THL W100 yesterday from an italian reseller... I ordered it already rooted and it arrived directly fron Hong Kong with the latest firmware 130711 and prerooted with Superuser (I checked it with root checker and it's effectively rooted...).
It also has it's own recovery pre installed (when I enter the recovery mode with pover+volume up it appears an "android recovery"...)...
I wanted to flash a different recovery (the Barry63 recovery) and so proceeded with installing in one of my four pc (running win XP SP3) the drivers I founf inside the Ro.edi package... after this, I turned off my phone, disassembled the battery, put the usb cable both on my phone and on my pc and finally inserted the battery... I hear the tipical sound played when you put a new USB device in a computer and immediately after (a secondo or so...) a second sound tipical of when you disconnect your USB device... all in all my phone automatically disconnects and this results in a "non installation" of the Mediatek USB preloader I neeed to use the SPFlashtool...
I tried on anoter pc of mines, running Win XP (a modded version) and got the same result...
I also tried another pc running Win7 Home Premium , forced the installation of the Mediatek USB preloader via the "hdwwiz" method, put the usb cable in both the phone and the pc, re-connected the battery and... it recognizes the new device, starts to install the Mediatek USB preloader, but after some seconds it says "device diconnected"....
Same issue on the fourth and last pc of mine running Win 7 starter...
It's like my phone has something in the firmware (root?Recovery?) that doesn't allow me to install the Mediatek USB preloader...
Any idea about it ?
My phone works perfectly, the pc recognizes it both as USB archive and USB debug... I can do almost all the things I want (the phone is rooted and so I installed all the apks I wanted, included the MobileUncleTools... but I can not use the SPFlash tool as I can not install the MediaTek USB preloader... :crying:
Thank you in advance for you precious answers...
usb debugging
did you enabled "usb debuging" in developer settings.
android---central.com/how-enable-developer-settings-android-42
buyukbalkan said:
did you enabled "usb debuging" in developer settings.
android---central.com/how-enable-developer-settings-android-42
Click to expand...
Click to collapse
Yes... it was enabled...
Anyway I solved the problem... I discovered that what it happened to my phone is the "supposed to be" for that driver... in fact, after launching SPFlashtool and press dowload, when you plug in the battery on the phone SPFlash recognize the phone and starts flashing the right way.
Finally I succeeded in it and flashed the Barry6030 recovery. :laugh:
Thank you :good:
bigboss1970 said:
Yes... it was enabled...
Anyway I solved the problem... I discovered that what it happened to my phone is the "supposed to be" for that driver... in fact, after launching SPFlashtool and press dowload, when you plug in the battery on the phone SPFlash recognize the phone and starts flashing the right way.
Finally I succeeded in it and flashed the Barry6030 recovery. :laugh:
Thank you :good:
Click to expand...
Click to collapse
I'm happy to hear that you can handle it...
Hello all,
I have a rooted Micromax A58 which was perfectly working. I did a full nandroid backup of it 2 days ago. On yesterday, I was moving some system app (google maps, play store etc) to SD with some software) so that I could increase the internal memory and install some other softwares. But, unfortunately, after that modification, the phone stopped working properly (it was stucking up when the BOLT logo was reached). So, I started it in recovery and do a wipe cache and factory reset. After that, the phone is always going to Factory Mode.
Then I tried to Flash the Stock ROM using Flash Tool but was unsuccessful multiple times. After the scatter file selected, when I clicked the 'Download' (or even firmware upgrade), all time time, the phone was disconnecting/reconnecting every now and then and nothing happened after (even though I already installed the Vcom and PdaNet driver in the PC). So, I had to quit. I am attaching herewith the logs of the Flash Tool lastly tried.
Now, when I am starting the phone power button, nothing is happening.. NOTHING but black screen...
I am a bit worried.. your help very much appreciated. Please let me know for any information needed. Thanks.
'No com port detected' error
I tried another time and the problem still there.. When in SP Flash Tool, I select scatter file, click 'Download' and connect the phone to PC, the process doesn't progress further. So, I have to finally click 'Stop' to quit. In the logs, it shows--
"No com port detected.."
Attaching the trace logs file herewith.
Please advice how to resolve the issue.. I am totally stuck now. Thanks.
Androhelp said:
Hello all,
I have a rooted Micromax A58 which was perfectly working. I did a full nandroid backup of it 2 days ago. On yesterday, I was moving some system app (google maps, play store etc) to SD with some software) so that I could increase the internal memory and install some other softwares. But, unfortunately, after that modification, the phone stopped working properly (it was stucking up when the BOLT logo was reached). So, I started it in recovery and do a wipe cache and factory reset. After that, the phone is always going to Factory Mode.
Then I tried to Flash the Stock ROM using Flash Tool but was unsuccessful multiple times. After the scatter file selected, when I clicked the 'Download' (or even firmware upgrade), all time time, the phone was disconnecting/reconnecting every now and then and nothing happened after (even though I already installed the Vcom and PdaNet driver in the PC). So, I had to quit. I am attaching herewith the logs of the Flash Tool lastly tried.
Now, when I am starting the phone power button, nothing is happening.. NOTHING but black screen...
I am a bit worried.. your help very much appreciated. Please let me know for any information needed. Thanks.
Click to expand...
Click to collapse
Try changing the ports, Cable etc or better off try on a different computer .
Port/Cable/PC change didn't help
kapil_dheer said:
Try changing the ports, Cable etc or better off try on a different computer .
Click to expand...
Click to collapse
Hello Kapil,
Thanks for the response. Yesterday I tried with separate laptop, but the same problem was there. Today, I tried with the different USB port.. but didn't help.
It seems that the driver can not recognize the device and when I connect the phone, it is just in a loop of disconnecting/re-connecting. Please advice further. Thanks.
Only option now seems is Service Centre.
The guys are pretty dumb. I've tested samsung motorola etc.....they don't even know what root is.
Maybe they'll be unable to identify what you tried to do.
You can give any reason for it not functioning.
Good luck.
kapil_dheer said:
Only option now seems is Service Centre.
The guys are pretty dumb. I've tested samsung motorola etc.....they don't even know what root is.
Maybe they'll be unable to identify what you tried to do.
You can give any reason for it not functioning.
Good luck.
Click to expand...
Click to collapse
Thank you Kapil for the advice. As Micromax service centre is not having a good reputation regarding these, so I would go for that option as the last resort.
Before that, can I please ask the other members for giving further advice if there is any option to try with.. Thanks for your help.
Managed to get phone reconized in PC usb-pls help further
Androhelp said:
Thank you Kapil for the advice. As Micromax service centre is not having a good reputation regarding these, so I would go for that option as the last resort.
Before that, can I please ask the other members for giving further advice if there is any option to try with.. Thanks for your help.
Click to expand...
Click to collapse
I have managed to get the phone recognized by PC usb now. But, when I try try the SP Flash utility to either Format or Download or Firmware update etc, it is throwing error like below--
09/16/2014 09:56:32.640 FlashTool[2212][3912][D]: APCore::Connection::ConnectDA(): Failed to Connect DA: S_FT_ENABLE_DRAM_FAIL(..\QT_FlashTool_Refactor\Conn\Connection.cpp,126)
09/16/2014 09:56:38.140 FlashTool[2212][3912][D]: BackgroundWorker::run(): BROM Exception! ( BROM ERROR : S_FT_ENABLE_DRAM_FAIL (4032)
[EMI] Enable DRAM Failed!
[HINT]:
Please check your load matches to your target which is to be downloaded.)((APCore::Connection::ConnectDA,..\QT_FlashTool_Refactor\Conn\Connection.cpp,127))(..\QT_FlashTool_Refactor\UI\src\BackgroundWorker.cpp,94)
09/16/2014 09:56:58.765 FlashTool[2212][2708][D]: OptionDialog::winEvent(): USB Device Removed.(..\QT_FlashTool_Refactor\UI\src\OptionDialog.cpp,483)
09/16/2014 09:56:59.750 FlashTool[2212][2708][D]: OptionDialog::winEvent(): USB Device plug in.(..\QT_FlashTool_Refactor\UI\src\OptionDialog.cpp,478)
09/16/2014 09:57:33.828 FlashTool[2212][2708][D]: OptionDialog::winEvent(): USB Device Removed.(..\QT_FlashTool_Refactor\UI\src\OptionDialog.cpp,483)
09/16/2014 09:57:34.812 FlashTool[2212][2708][D]: OptionDialog::winEvent(): USB Device plug in.(..\QT_FlashTool_Refactor\UI\src\OptionDialog.cpp,478)
09/16/2014 09:58:08.890 FlashTool[2212][2708][D]: OptionDialog::winEvent(): USB Device Removed.(..\QT_FlashTool_Refactor\UI\src\OptionDialog.cpp,483)
09/16/2014 09:58:10.375 FlashTool[2212][2708][D]: OptionDialog::winEvent(): USB Device plug in.(..\QT_FlashTool_Refactor\UI\src\OptionDialog.cpp,478)
I tried the above multiple times but everytime same error as above.
When tried to connect the phone (without battery) it is disconnect/reconnect in an endless loop.
When try to connect with battery, the disconnect/reconnect loop is gone (i.e.-stable) but sometime it can not identity phone ('Unknown Device').
Also tried to press volume down button along with battery inside, but showing 'Unknown Device' and Flash tool getting hanged.
I used the Stock Rom downloaded from xda site for my phone detailed below---
Android 4.2.2
Model Micromax A58
BaseBand version- MOLY.WR8.W1315.MD.WG.MP.V1.P11 2013/09/04 15:51
Kernel 3.4.5 [email protected] #1
Build Number Micromax A58_T09
I also have the good nandroid backup (if it could be of any use) but phone is dead now. Confused how to go forward. Please help.
Download in SP Flash Tool successful
Androhelp said:
I have managed to get the phone recognized by PC usb now. But, when I try try the SP Flash utility to either Format or Download or Firmware update etc, it is throwing error like below--
09/16/2014 09:56:32.640 FlashTool[2212][3912][D]: APCore::Connection::ConnectDA(): Failed to Connect DA: S_FT_ENABLE_DRAM_FAIL(..\QT_FlashTool_Refactor\Conn\Connection.cpp,126)
09/16/2014 09:56:38.140 FlashTool[2212][3912][D]: BackgroundWorker::run(): BROM Exception! ( BROM ERROR : S_FT_ENABLE_DRAM_FAIL (4032)
[EMI] Enable DRAM Failed!
[HINT]:
Please check your load matches to your target which is to be downloaded.)((APCore::Connection::ConnectDA,..\QT_FlashTool_Refactor\Conn\Connection.cpp,127))(..\QT_FlashTool_Refactor\UI\src\BackgroundWorker.cpp,94)
09/16/2014 09:56:58.765 FlashTool[2212][2708][D]: OptionDialog::winEvent(): USB Device Removed.(..\QT_FlashTool_Refactor\UI\src\OptionDialog.cpp,483)
09/16/2014 09:56:59.750 FlashTool[2212][2708][D]: OptionDialog::winEvent(): USB Device plug in.(..\QT_FlashTool_Refactor\UI\src\OptionDialog.cpp,478)
09/16/2014 09:57:33.828 FlashTool[2212][2708][D]: OptionDialog::winEvent(): USB Device Removed.(..\QT_FlashTool_Refactor\UI\src\OptionDialog.cpp,483)
09/16/2014 09:57:34.812 FlashTool[2212][2708][D]: OptionDialog::winEvent(): USB Device plug in.(..\QT_FlashTool_Refactor\UI\src\OptionDialog.cpp,478)
09/16/2014 09:58:08.890 FlashTool[2212][2708][D]: OptionDialog::winEvent(): USB Device Removed.(..\QT_FlashTool_Refactor\UI\src\OptionDialog.cpp,483)
09/16/2014 09:58:10.375 FlashTool[2212][2708][D]: OptionDialog::winEvent(): USB Device plug in.(..\QT_FlashTool_Refactor\UI\src\OptionDialog.cpp,478)
I tried the above multiple times but everytime same error as above.
When tried to connect the phone (without battery) it is disconnect/reconnect in an endless loop.
When try to connect with battery, the disconnect/reconnect loop is gone (i.e.-stable) but sometime it can not identity phone ('Unknown Device').
Also tried to press volume down button along with battery inside, but showing 'Unknown Device' and Flash tool getting hanged.
I used the Stock Rom downloaded from xda site for my phone detailed below---
Android 4.2.2
Model Micromax A58
BaseBand version- MOLY.WR8.W1315.MD.WG.MP.V1.P11 2013/09/04 15:51
Kernel 3.4.5 [email protected] #1
Build Number Micromax A58_T09
I also have the good nandroid backup (if it could be of any use) but phone is dead now. Confused how to go forward. Please help.
Click to expand...
Click to collapse
In the meanwhile, when trying to resolve the issue, I tried the following steps and after that, I lastly managed to 'download' the Stock ROM successfully in my phone (using the Windows XP OS)--
1) As I was always getting the SP Flash Tool error 4032 for last couple of days and which was clearly describing 'please check your load matches your target which is to be downloaded', so was investigating the root cause in details. Upon searching in the internet, I downloaded multiple version of Stock ROMs for my Micromax A58 model from different sources to give a try. When trying to 'Download' (in SP Flash Tool), the 'T_09' ROM (link given by 'alanvmathew') in the below mentioned URL worked for me.
http://forum.xda-developers.com/showthread.php?t=2610046&page=2
It is to be noted from the link that Micromax A58 model have 2 different Stock ROMs (i.e.- 'T_07' and 'T_09') which info I was missing all the time.
2) After identifying the scatter file in the SP Flash Tool and clicking the 'Download' option, I inserted battery in the phone and pressing the 'Power + Volume down' button, connected the device into the PC USB. Upon connected, the 'DA USB VCOM PORT' driver automatically installed and the 'Download' started and flashing of ROM went smooth. Finally, it ended up with green 'Download OK' message. Also attaching the snapshots herewith.
Will check the mobile and its performance further and revert back accordingly.
Hey Guys
I bricked my P780 and didnt do a backup. I formated the phone with SpFlashTool, afterwards the Flashing didnt work. And a second format didnt work too.
Now i tried nearly every possible tutorial on the web...
I am using win7
My main problem is that i am using SpFlashTool (newest version) and i get an 4032 Error if i try to download the rom.
I tried nearly every Rom for the p780 with every possible scatter file.
I tried nearly every MediaTek DA VCOM USB Driver, MediaTek PreLoader VCOM USB Driver and MTK USB Port Driver and always with no success.
I even plugged out the battery (its not removable) without damaging the phone...
Spackotus said:
Hey Guys
I bricked my P780 and didnt do a backup. I formated the phone with SpFlashTool, afterwards the Flashing didnt work. And a second format didnt work too.
Now i tried nearly every possible tutorial on the web...
I am using win7
My main problem is that i am using SpFlashTool (newest version) and i get an 4032 Error if i try to download the rom.
I tried nearly every Rom for the p780 with every possible scatter file.
I tried nearly every MediaTek DA VCOM USB Driver, MediaTek PreLoader VCOM USB Driver and MTK USB Port Driver and always with no success.
I even plugged out the battery (its not removable) without damaging the phone...
Click to expand...
Click to collapse
Hi. Because you have formated your nand you must reinstall your drivers, because your preloader now is messed up.
In order to do that you must do this:
1. Install drivers.
2. Go to device manager and let the window open.
3. Connect your phone and new hardware should appear for just a seccond or 2 max, something with MTK 6.5.XXX.
4. Click very fast on the little new thing that appear there because will desapear.
5. Now press the button to update drivers hardware. In one of my posts you will find an archive with the right drivers. Drivers are on the archive uploaded here.
6. After the drivers are installed your PC should recognize the phone.
7. After this the steps should be the same to flash your ROM. Oh and by the way: Press Firmware Upgrade button not Download. And dont forget to check DA/DL With Checksum... option
8. Waiting for feedback.
9. Good Luck.
stympy said:
Hi. Because you have formated your nand you must reinstall your drivers, because your preloader now is messed up.
In order to do that you must do this:
1. Install drivers.
2. Go to device manager and let the window open.
3. Connect your phone and new hardware should appear for just a seccond or 2 max, something with MTK 6.5.XXX.
4. Click very fast on the little new thing that appear there because will desapear.
5. Now press the button to update drivers hardware. In one of my posts you will find an archive with the right drivers. Drivers are on the archive uploaded here.
6. After the drivers are installed your PC should recognize the phone.
7. After this the steps should be the same to flash your ROM. Oh and by the way: Press Firmware Upgrade button not Download. And dont forget to check DA/DL With Checksum... option
8. Waiting for feedback.
9. Good Luck.
Click to expand...
Click to collapse
First of all thanx!
But whitch driver i should install in Point 1. ?
Second, what should i do if the device is appearing for 2 sec, the device appears straight as unknown device and then replugs itself every 30 sec
Spackotus said:
First of all thanx!
But whitch driver i should install in Point 1. ?
Second, what should i do if the device is appearing for 2 sec, the device appears straight as unknown device and then replugs itself every 30 sec
Click to expand...
Click to collapse
Hi. The drivers i uploaded to you at my post!
For the new device you must have the device manager window open ! Only there you will find the preloader.
stympy said:
Hi. The drivers i uploaded to you at my post!
For the new device you must have the device manager window open ! Only there you will find the preloader.
Click to expand...
Click to collapse
Well the device appears straight as MTK USB Port, , there is no 2 sec TimeFrame when the device apears as MT65xx
an yes, i installed your driver, i am even using a new installation of win7
Hi guys.. sory to butt in... but im experiencing the same problem where in my case i have lenovo s720 instead.
Does the solution works for u?? Mine says something about partition manager eror.
beckham_totti said:
Hi guys.. sory to butt in... but im experiencing the same problem where in my case i have lenovo s720 instead.
Does the solution works for u?? Mine says something about partition manager eror.
Click to expand...
Click to collapse
The solution should work for you! Or else search on this forum itself and you will get your answer!
Does somebody have any information or encounter about this? The device is a Blu Energy X Plus 2, a back up phone I wanted to experiment with.
-After unlocking bootloader using ADB, phone got stuck at boot logo.
-I forgot to wipe.
-Device is not yet rooted
-After waiting for minutes I have forced the phone to shut down.
-Volume+Power combo, battery is non removable
-Now it wont turn on and respond to any button.
-It charges, as proven by the red light.
-It is somehow detected by the PC using the VCOM drivers. PC makes a sound and MT65xx PreLoader VCOM appears in the Device Manager.
-SP Flash Tool will not start download. Even tried download before plugging in usb, nothing happens.
-Tried many different flash tools versions. 1628, v5, v3, Nothing works. No error message but an error appears when I plug out the USB cord
-BROM Error: S_BROM_CMD_STARTCMD_FAIL(0x7D5)
Cannot pass bootroom start command! Possibly target power up too early.
Hi , maybe your SP Flash tool is not compatible for your chip , so try this one :
https://spflashtool.com/download/SP_Flash_Tool_v5.1628_Win.zip
Search firmware exactly for your device model .
You can use IDM -Internet Dowwnload Manager for fast downloading...
Teddy Lo said:
Hi , maybe your SP Flash tool is not compatible for your chip , so try this one :
https://spflashtool.com/download/SP_Flash_Tool_v5.1628_Win.zip
Search firmware exactly for your device model .
You can use IDM -Internet Dowwnload Manager for fast downloading...
Click to expand...
Click to collapse
I have already tried the 5.1628 version, it is also not working.
The latest version has a bug I think which causes it to have a RUntime error when picking a scatter file.
The old v3 will not accept any scatter file anymore.
Also I have downloaded two versions of stock rom already. First one is 800 mb and the second one is 2GB. Both do not work, but I suspect the first one to completely fail since it had an unmatching scatter file within.
Try this.Hold power button for 2 min if your phone boots up Good News It's usable.If not then It's only crap now.Mediatek devices are not supposed to be rooted and if somehow you managed to do that they will make sure you pay for it.
Sent from my Pixel 3 XL using Tapatalk
Atifbaig786 said:
Try this.Hold power button for 2 min if your phone boots up Good News It's usable.If not then It's only crap now.Mediatek devices are not supposed to be rooted and if somehow you managed to do that they will make sure you pay for it.
Sent from my Pixel 3 XL using Tapatalk
Click to expand...
Click to collapse
I tried it but the device doesnt seem to respond to any button whatsoever. The device is not rooted though, I wanted to flash magisk but it all happened after unlocking the bootloader. But I have hope since the preloader is indeed detected in the PC.
Try to relock bootloader with adb if your device is recognised by ADB ...
Teddy Lo said:
Try to relock bootloader with adb if your device is recognised by ADB ...
Click to expand...
Click to collapse
device is no longer recognized by adb, it wont turn on anymore. Only as MT65xx preloader as it shows in the device manager
helpplease123 said:
device is no longer recognized by adb, it wont turn on anymore. Only as MT65xx preloader as it shows in the device manager
Click to expand...
Click to collapse
Follow this thread maybe is driver issue so read carefully ...
https://forum.xda-developers.com/showthread.php?t=2180436
Good luck
What's up with VCOM?
Well I don't think your PC would be able to detect your device because you haven't got the VCOM drivers yet. Get any VCOM driver for Mediatek, and then disable driver signature enforcing on Windows. Now fire up SPFT and select the scatter use v5.1628 as the newer ones seem to be unstable (also verified by OP). Now choose the Preloader for your device and then enter download mode. Turn off the phone (if you can't, just let it die until the battery is over). And then connect it using an USB cable, while SPFT is in download mode. You should be able to unbrick your device.
And as you said S_BROM_CMD_STARTCMD_FAIL(0x7D5), that is when the device powers up too early before the flash could begin. The 8 byte token is not received by the preloader and hence it ain't working. This is why you have to switch your phone off completely, and also try using a different USB cable
Note:
The preloader parition has an emergency download mode which is used to enable the download to take place. Now, if you flash the wrong preloader, then your device won't even be detected in SPFT or anywhere else. So yeah, in MTK preloader is the life of your phone. Please verify that you are flashing the correct preloader
BusinessKid said:
Well I don't think your PC would be able to detect your device because you haven't got the VCOM drivers yet. Get any VCOM driver for Mediatek, and then disable driver signature enforcing on Windows. Now fire up SPFT and select the scatter use v5.1628 as the newer ones seem to be unstable (also verified by OP). Now choose the Preloader for your device and then enter download mode. Turn off the phone (if you can't, just let it die until the battery is over). And then connect it using an USB cable, while SPFT is in download mode. You should be able to unbrick your device.
And as you said S_BROM_CMD_STARTCMD_FAIL(0x7D5), that is when the device powers up too early before the flash could begin. The 8 byte token is not received by the preloader and hence it ain't working. This is why you have to switch your phone off completely, and also try using a different USB cable
Note:
The preloader parition has an emergency download mode which is used to enable the download to take place. Now, if you flash the wrong preloader, then your device won't even be detected in SPFT or anywhere else. So yeah, in MTK preloader is the life of your phone. Please verify that you are flashing the correct preloader
Click to expand...
Click to collapse
Tried everything here, and I even used a windows 7 pc but it is still not working. The VCOM was already installed, in fact when I plug in the phone windows automatically detects it as the MTK Preloader VCOM USB port(COM13) in the device manager. The VCOM driver that is supposed to be installed leaves an error in the device manager (COM12). SP Flash tool still will not start flashing. No error messages, until I plug out the usb cord.
helpplease123 said:
Tried everything here, and I even used a windows 7 pc but it is still not working. The VCOM was already installed, in fact when I plug in the phone windows automatically detects it as the MTK Preloader VCOM USB port(COM13) in the device manager. The VCOM driver that is supposed to be installed leaves an error in the device manager (COM12). SP Flash tool still will not start flashing. No error messages, until I plug out the usb cord.
Click to expand...
Click to collapse
You do see that exclamation right - this means it isn't properly configured
---------- Post added at 01:37 PM ---------- Previous post was at 01:35 PM ----------
helpplease123 said:
Tried everything here, and I even used a windows 7 pc but it is still not working. The VCOM was already installed, in fact when I plug in the phone windows automatically detects it as the MTK Preloader VCOM USB port(COM13) in the device manager. The VCOM driver that is supposed to be installed leaves an error in the device manager (COM12). SP Flash tool still will not start flashing. No error messages, until I plug out the usb cord.
Click to expand...
Click to collapse
Looks like it's more of a Windows issue than your phone. If your preloader's good - you're safe. I think it's a COM bridge issue. Just stay on the wait and I'll get back to you in a minute or two
---------- Post added at 01:40 PM ---------- Previous post was at 01:37 PM ----------
I'm working on a batch script for you to fix the COM issue. Would you mind sharing your Windows Version and Architecture?
I'm building it for Windows 7 x64 - if that's your PC?
BusinessKid said:
You do see that exclamation right - this means it isn't properly configured
Click to expand...
Click to collapse
---------- Post added at 01:37 PM ---------- Previous post was at 01:35 PM ----------
I mean the COM13 is fairly OK for the part, its the VCOM that comes from installing the phone. However the COM12 that came from the manual installer had the exclamation point.
Looks like it's more of a Windows issue than your phone. If your preloader's good - you're safe. I think it's a COM bridge issue. Just stay on the wait and I'll get back to you in a minute or two
---------- Post added at 01:40 PM ---------- Previous post was at 01:37 PM ----------
Click to expand...
Click to collapse
Its already a great thanks from me for you to even post more than once. thank you so much!
[/COLOR]I'm working on a batch script for you to fix the COM issue. Would you mind sharing your Windows Version and Architecture?
I'm building it for Windows 7 x64 - if that's your PC?
Click to expand...
Click to collapse
Yes, in fact I have first tried it in Windows 10 x64 before switching back to this W7 x64 laptop. Same problem same outcome though
So let us go 101
Okay - the first thing that we'd do now is blow off those crappy drivers - uninstall them! Now get on your Windows 10 x64 PC. Install the VCOM drivers from this XDA thread. It's for elephone, however I've used it myself and it works really well on almost any device. Now power off your phone completely (no bootlooop, completely dark screen). Launch SPFT, select scatter, select the correct preloader and then hit on download. Do not connect your phone now! Now wait for 10 seconds. Now connect your phone. And let the download begin. If it works - fantastic, if it doesn't ping me back and I'll be waiting for replying to you. The batch script is almost done (I was doing some kernel work), I'll upload it once I'll be back home (on the way back now).
Fingers crossed :fingers-crossed:
BusinessKid said:
Okay - the first thing that we'd do now is blow off those crappy drivers - uninstall them! Now get on your Windows 10 x64 PC. Install the VCOM drivers from this XDA thread. It's for elephone, however I've used it myself and it works really well on almost any device. Now power off your phone completely (no bootlooop, completely dark screen). Launch SPFT, select scatter, select the correct preloader and then hit on download. Do not connect your phone now! Now wait for 10 seconds. Now connect your phone. And let the download begin. If it works - fantastic, if it doesn't ping me back and I'll be waiting for replying to you. The batch script is almost done (I was doing some kernel work), I'll upload it once I'll be back home (on the way back now).
Fingers crossed :fingers-crossed:
Click to expand...
Click to collapse
Dude holy ****, I cannot believe that it worked! I swear I was very confident that the problem was not in the drivers, but out of luck I started to follow that guide again from start to finish and selected the "MTK USB Port" in the device manager section. Then I plugged in and SP flash tool finally started! You rock!
Your welcome! I'm glad that worked!