Completely f****d my G-Watch - LG G Watch

SO, tl;dr-- My LG G watch turns on, then enters into a point where it is stuck doing the swirling colors boot animation until the battery dies. If I boot into bootloader mode, I cannot do anything other than reboot bootloader or power off. Recovery does not work, when I try it gives me the android guy on his back and tapping the screen does nothing. The restore tool used to be able to interface with my device, but now it does not even show up under 'adb devices.' If anyone could tell me something I can do, it would be greatly appreciated.

Is your bootloader unlocked?

Yes, I have an unlocked bootloader. When I turn the device on, it shows the little 'unlocked' symbol.

If you boot to bootloader mode can you run fastboot commands? If so, download one of the 6.0.1 roms from XDA and then follow the install instructions. If not....hmmm, not sure!

feyd2blak said:
If you boot to bootloader mode can you run fastboot commands? If so, download one of the 6.0.1 roms from XDA and then follow the install instructions. If not....hmmm, not sure!
Click to expand...
Click to collapse
How do I do fastboot commands? I can boot to bootloader mode, and the restore tool talks with my watch and recognizes it as a device sometimes.

Via a USB cable connected to a computer and the fastboot tool installed on that computer. You also need the correct fastboot drivers for this.

Related

[Q] How to flash recovery without USB debugging mode activated on a bricked Nexus S?

Hi,
I had flashed the NexusXperia ROM on my Nexus S just recently. After trying it out I restored the stock ICS 4.0.4....
For some reason the phone keeps on showing the HD bootscreen continously without starting up....
I thought of clearing the dalvik and re-installing via restore however now that it's not got any recovery neither is it being detected on my pc....
I remember deactivating the USB debugging mode and probably this could be the reason it's not being detected....
Is there a way to flash recovery without debugging mode switched ON or is there a way to simply switch ON the USB debugging mode from bootloader screen....
ANY HELP IS APPRECIATED ON THIS....
I have tried on windows 7 as well as on Ubuntu....but the device is not detected....thanks in advance.....
- DarKmentoR
On the Nexus S, holding Volume Up while turning on the power will load the bootloader and from there you should be able to use fastboot to install a custom recovery using fastboot. You should not need USB debugging enabled for this to work.
http://wiki.cyanogenmod.com/wiki/Ne...de#Installing_the_ClockworkMod_Recovery_Image
C:\nexussrootnew> fastboot flash recovery recovery.img
< waiting for device >
-------------------------------------------------------------
Just keeps on waiting for the device....adb not able to detect the device too
The phone is in the bootloader mode and fastboot doesn't detect it? Sounds like it is completely broken then, your only option may be the UnBrickable Mod: http://forum.xda-developers.com/showthread.php?t=1566475
Ok...i can see a "FASTBOOT MODE" written in red when i switch on using Vol+ & Power....
Which mode is it ? Fastboot or Download....?
darkmentor25 said:
Ok...i can see a "FASTBOOT MODE" written in red when i switch on using Vol+ & Power....
Which mode is it ? Fastboot or Download....?
Click to expand...
Click to collapse
Fastboot is the mode you need to be in for fastboot.exe to detect the phone. Put it into that mode and try to flash the recovery with fastboot.exe using the command you posted above.
I have HUAWEI P smart. I am searching for a firmware for flash my phone.

[Q] T-mobile HTC one Brick

I've had this phone for about a good 4 months now, was getting bored so i decide to unlock the bootloader, root, and install a new rom. Then i heard youwer able to activate the HTC logo button to wake and sleep your device with using a different kernel. tbaldens kernel v3.6. I have TWRP recovery installed with trickdroid as my rom.After i ran threw all the procedures to flash in Aroma installer. My phone won't turn on, when i connect it to my computer it shows up as a MTP device. When I do get it to power on its stuck at the "quietly brilliant" screen. cant get into recovery to restore from back up. PLEASE HELP! SOLDIER DEPLOYED!!!!!!!! dont have the means of sending it in. Any suggestion. Mac is my primary means of rooting. windows 8 drivers are kinda funky:crying::crying::crying::crying::crying::crying::crying:
If you have access to a Windows 7 PC, then download the RUU for your device. Next, relock your bootloader (fastboot oem lock) Next step, if you have bootloader access to your device, then you can go into fastboot (make sure it says fastboot USB). Open a command prompt, and type in fastboot oem rebootRUU. You're in RUU mode, where you can run the RUU and reset everything back to stock.
crashfocus said:
If you have access to a Windows 7 PC, then download the RUU for your device. Next, relock your bootloader (fastboot oem lock) Next step, if you have bootloader access to your device, then you can go into fastboot (make sure it says fastboot USB). Open a command prompt, and type in fastboot oem rebootRUU. You're in RUU mode, where you can run the RUU and reset everything back to stock.
Click to expand...
Click to collapse
can i do this from a mac? and i can't get into fastboot because it wont go past the htc logo screen. it is identified as a MTP device in windows
Ahhhh thankfully i was able to get into my bootloader and flash my recovery! but thanks for the reply bro

[Q] HTC One stuck in bootloader

Hey guys I need help. My HTC One is stuck in bootloader mode. I was trying to upgrade to the latest T-Mobile update. I tried downgrading with an RUU and I tired to flash stock recovery. I'm not all too sure what exactly happened, but I have no OS or recovery mode. All I have is bootloader mode. When I try to reboot to OS there is a bootloop. When I try to go into recovery a picture of a phone shows up with a red triangle and exclamation point. When I enter Fastboot in the bootloader it shows up on the phone as Fastboot USB. Although it says Fastboot USB, the phone is not recognized on the computer. When I try to enter fastboot commands, the prompt says "waiting for device" no matter what command I type.
If I could get the computer to recognize the phone, I could flash a recovery and a ROM or run an RUU. But that is only if I could get it to recognize the phone and I can't. I have searched for days and I can't find anything that works.
I have no OS, no recovery mode, and the bootloader isn't recognized on the computer. Please help! any help/advice will be greatly appriciated!
Please and thank you! :good:
amkivb said:
Hey guys I need help. My HTC One is stuck in bootloader mode. I was trying to upgrade to the latest T-Mobile update. I tried downgrading with an RUU and I tired to flash stock recovery. I'm not all too sure what exactly happened, but I have no OS or recovery mode. All I have is bootloader mode. When I try to reboot to OS there is a bootloop. When I try to go into recovery a picture of a phone shows up with a red triangle and exclamation point. When I enter Fastboot in the bootloader it shows up on the phone as Fastboot USB. Although it says Fastboot USB, the phone is not recognized on the computer. When I try to enter fastboot commands, the prompt says "waiting for device" no matter what command I type.
If I could get the computer to recognize the phone, I could flash a recovery and a ROM or run an RUU. But that is only if I could get it to recognize the phone and I can't. I have searched for days and I can't find anything that works.
I have no OS, no recovery mode, and the bootloader isn't recognized on the computer. Please help! any help/advice will be greatly appriciated!
Please and thank you! :good:
Click to expand...
Click to collapse
keep on rebooting until it's seen in the PC. Make sure the driver is installed (or forcible install it if it's an unknown device).
After that, once you're able to see it... re-flash the unlock token (fastboot flase unlocktoken unlock_code.bin). That will get you back into the ROM. At least, that's what did for me:
http://forum.xda-developers.com/showthread.php?t=2665481
But I can't reflash an older RUU at all, so I can't downgrade.
Drashna said:
keep on rebooting until it's seen in the PC. Make sure the driver is installed (or forcible install it if it's an unknown device).
After that, once you're able to see it... re-flash the unlock token (fastboot flase unlocktoken unlock_code.bin). That will get you back into the ROM. At least, that's what did for me:
http://forum.xda-developers.com/showthread.php?t=2665481
But I can't reflash an older RUU at all, so I can't downgrade.
Click to expand...
Click to collapse
I figured it out. All I needed was windows 7 instead of 8 for some reason. After I installed 7 I just ran the 4.3 RUU. Now I have a different problem. Originally this all happened because I was going to upgrade to the new 4.4.2. Now I can't flash stock recovery. I have cwm but I need stock recovery to upgrade to 4.4.2. Since there is no 4.4.2 RUU I don't know what to do now.

Need help with bricked Redmi Note 3 Pro (Kenzo/Snapdragon)

Dear Community,
I got my Note 3 Pro Snapdragon Version today and I tried unlocking the bootloader, installing root and TWRP.
Unfortunately after I installed TWRP, WiFi didnt work anymore so I wanted to go back to where I was before.
i tried flashing the GlobalRom with the MiFlash Tool but somehow I'm now stuck with a bootloop.
The phone starts up and shows the MI Logo but doesnt go on. I tried booting TWRP temporarily via fastboot commands so that I can try to flash flashable zip files
but it doesnt let me execute "fastboot boot xyz.img" anymore because my device is locked.
I would really love to hear any solutions or ideas. I dont want any root or something anymore. If someone has an idea Im very happy!!!
thanks a lot in advance and tell me if you need any more infos
Paul/shisaya24
1. keep vol + and vol - pressed while connecting USB to enter adb mode
2. check if phone is connected with "adb devices" in command line, if phone shows up, enter "adb reboot edl"
3. now you can flash via MiFlash
Alex3oe said:
1. keep vol + and vol - pressed while connecting USB to enter adb mode
2. check if phone is connected with "adb devices" in command line, if phone shows up, enter "adb reboot edl"
3. now you can flash via MiFlash
Click to expand...
Click to collapse
First of all, HUGE thanks for your fast answer!
Unfortunately I couldnt get this to work. Since I am stuck at the Logog screen here is what I tried:
Pressing both volume buttons while Logo Screen and plugging USB.
Pressing both colume buttons while fastboot screen is up.
These two didnt enter adb mode, I guess because of the bootloop I'm in
I also tried antering recovery mode with volume up + power button. Pressing both volume buttons didnt help either but when I am in recovery like that it shows my device in adb as "sideload" device.
Maybe that helps ? Can you give further advice or am I doomed?
My idea would be: Is it possible to reflash the device completely only usinf fastboot? The only thing I seem to be able to enter is fastboot...
Is there a way from fastboot to "working phone" ?
or maybe through the "adb sideload" state?
thanks a lot in advance!
Paul
EDIT
tried installing via "adb sideload xyz.zip" command but after shortly showing a status bar on phone screen it aborted and said "Total xfer: 0.00x" on PC screen .
Also: I read "adb reboot edl" brings you to download mode so you can flash something. Tried it but the phone just rebooted the normal system, so it stuck on Logo again...
search miui forum for unbrick, there is 2 or 3 method without opening your device
exp: http://en.miui.com/forum.php?mod=viewthread&tid=257227
Unfortunately they all do not work because they always require either a phone in download mode, and i only get to fastboot and adb sideboard or they require flashing something via fastboot but I can't do that either because it says my device is locked if I try...
Any suggestions how to flash a ROM with fastboot only or with adb sideload?
Thanks a lot
Paul
shisaya24 said:
Unfortunately they all do not work because they always require either a phone in download mode, and i only get to fastboot and adb sideboard or they require flashing something via fastboot but I can't do that either because it says my device is locked if I try...
Any suggestions how to flash a ROM with fastboot only or with adb sideload?
Thanks a lot
Paul
Click to expand...
Click to collapse
I Had The Same Issue Brother ! There are only 2 Things which you can do now .
1. Test Point Method to enter EDL
2.Give it to Service Center . I Gave Mine to Service Center ,They Fixed it in 30 mins or less and it was free
Dharani_V said:
I Had The Same Issue Brother ! There are only 2 Things which you can do now .
1. Test Point Method to enter EDL
2.Give it to Service Center . I Gave Mine to Service Center ,They Fixed it in 30 mins or less and it was free
Click to expand...
Click to collapse
Can I do the test point thing myself or is it risky?
What kind of service center? A general mobile phone repair shop or a Xiaomi special one?
shisaya24 said:
First of all, HUGE thanks for your fast answer!
Unfortunately I couldnt get this to work. Since I am stuck at the Logog screen here is what I tried:
Pressing both volume buttons while Logo Screen and plugging USB.
Pressing both colume buttons while fastboot screen is up.
These two didnt enter adb mode, I guess because of the bootloop I'm in
I also tried antering recovery mode with volume up + power button. Pressing both volume buttons didnt help either but when I am in recovery like that it shows my device in adb as "sideload" device.
Maybe that helps ? Can you give further advice or am I doomed?
My idea would be: Is it possible to reflash the device completely only usinf fastboot? The only thing I seem to be able to enter is fastboot...
Is there a way from fastboot to "working phone" ?
or maybe through the "adb sideload" state?
thanks a lot in advance!
Paul
EDIT
tried installing via "adb sideload xyz.zip" command but after shortly showing a status bar on phone screen it aborted and said "Total xfer: 0.00x" on PC screen .
Also: I read "adb reboot edl" brings you to download mode so you can flash something. Tried it but the phone just rebooted the normal system, so it stuck on Logo again...
Click to expand...
Click to collapse
I've been facing the same (or a similar?) problem about a week ago but managed to get out. Knowing me for having a head like a sieve I made some notes, sadly quite rudimentary
Did you try to flash with MiFlash after "adb reboot edl"? If I remember rightly after "adb reboot edl" you got the logo like booting another way, but the light is blinking red. Then I could flash via MiFlash.
I'm quite sure that if you get a "reboot" after entering "adb reboot edl", your phone will be in edl mode.
I will try that this evening when I am at home again and report. Thanks
Alex3oe said:
I've been facing the same (or a similar?) problem about a week ago but managed to get out. Knowing me for having a head like a sieve I made some notes, sadly quite rudimentary
Did you try to flash with MiFlash after "adb reboot edl"? If I remember rightly after "adb reboot edl" you got the logo like booting another way, but the light is blinking red. Then I could flash via MiFlash.
I'm quite sure that if you get a "reboot" after entering "adb reboot edl", your phone will be in edl mode.
Click to expand...
Click to collapse
Unfortunately this doesnt work. Phone reboots and shows MI Logo but red light doesnt blink and MiFlash doesnt recognize any devices.
Do you have another idea? :/
How did you unlock the bootloader, via official permission or that unofficial hack?
Sent from my Moto G using Tapatalk
I didnt use the official way :/ Im so hoping my phone isnt broken. I wish i owuld have been more patient
shisaya24 said:
I didnt use the official way :/ Im so hoping my phone isnt broken. I wish i owuld have been more patient
Click to expand...
Click to collapse
Only options you have right now are:
1) using test points method which is a but cumbersome and voids warranty if you care about that.
2) go to a xiaomi service center of you have any nearby.
It is hard bricked.
So there is absolutely no option to unlock bootlader via adb sideload or fastboot ?
shisaya24 said:
So there is absolutely no option to unlock bootlader via adb sideload or fastboot ?
Click to expand...
Click to collapse
Apparently, no! Whenever using unofficial methods, read precautions carefully and you missed all as I can see. Wait if someone can help you out.
apply official unlock. then unlock your device from fastboot mode.
asaharaSK said:
apply official unlock. then unlock your device from fastboot mode.
Click to expand...
Click to collapse
That sounds nice and easy. I already applied for official unlock.
But: do you know if u can use the official unlock now? I can only access fastboot and adb sideload mode. Is it possible to activate official unlock from there? Or do I need a working ROM rather?
I would have thought that official unlock doesn't work from fastboot /adb sideload...
shisaya24 said:
That sounds nice and easy. I already applied for official unlock.
But: do you know if u can use the official unlock now? I can only access fastboot and adb sideload mode. Is it possible to activate official unlock from there? Or do I need a working ROM rather?
I would have thought that official unlock doesn't work from fastboot /adb sideload...
Click to expand...
Click to collapse
Does anyone know this?
I have the same problem. I made the same mistakes as shisaya24. I have followed every procedure for unbricking and nothing works. I even applied for an unlock code and got it from Xiomi. I used their mi-unlock app which requires fastboot (pwr/vol-) but it gets to 50% and bombs out. It states it can't verify the phone. Can anyone please help me??
smiley1960 said:
I have the same problem. I made the same mistakes as shisaya24. I have followed every procedure for unbricking and nothing works. I even applied for an unlock code and got it from Xiomi. I used their mi-unlock app which requires fastboot (pwr/vol-) but it gets to 50% and bombs out. It states it can't verify the phone. Can anyone please help me??
Click to expand...
Click to collapse
out of sheer desperation I tried MiPhone again and after a few tries, MiPhone started updating the OS. My phone now works again and I have an unlock code as well.

Lost download mode and fastboot after unlock bootloader

I followed some tips to unlock bootloader my v300k, after that my phone cant boot into any mode so it brick. I use box to go to stock but it still dont have download mode and fastboot .What can i do ?. My phone now have bootloader unlocked but i cant instal twrp because i cant access download mode or fastboot on us998.
All help will be appreciated
So you are saying that you get the warning about having an unlocked bootloader, but you can't boot to fastboot? That doesn't make sense...
With the phone off, hold vol down and plug in the USB cable -- what do you get?
-- Brian
provide screen shots and exact steps you are doing.
For example screen shot of download mode
turn phone off
press volume up
insert USB cable
provide screenshot
for entering fastboot
enable oem debug mode
connect USB cable
make sure phone is using photo mode
adb devices
adb reboot bootloader
fastboot devices
provide screenshot
giabao574 said:
I followed some tips to unlock bootloader my v300k, after that my phone cant boot into any mode so it brick. I use box to go to stock but it still dont have download mode and fastboot .What can i do ?. My phone now have bootloader unlocked but i cant instal twrp because i cant access download mode or fastboot on us998.
All help will be appreciated
Click to expand...
Click to collapse
What exact tips did you fallow?
Alibaba0101 said:
provide screen shots and exact steps you are doing.
For example screen shot of download mode
turn phone off
press volume up
insert USB cable
provide screenshot
for entering fastboot
enable oem debug mode
connect USB cable
make sure phone is using photo mode
adb devices
adb reboot bootloader
fastboot devices
provide screenshot
Click to expand...
Click to collapse
When i plug cable to go to download mode , it always turn to Charge Screen. I cant get into mainscreen, it's bootlooping after a few second on setup screen ( after flasf US998)
Ainz_Ooal_Gown said:
What exact tips did you fallow?
Click to expand...
Click to collapse
Tips from https://forum.xda-developers.com/showpost.php?p=76989743&postcount=7

Categories

Resources