Related
Hi,
My friend gave me this phone to update the rom, but I'm facing a problem. Device was rooted, recovery is installed, but some really old one - it doesn't even say what kind of recovery it is. So I read that I need to update to TWRP 2.8.4.0 rev.2. Tried flashing it with TWRP apk, but after choosing it and hitting install, it reboots and goes into old recovery and I can't install new TWRP. Then I tried installing it with this guide: http://rootoreviews.com/root-Lenovo-P780-install-twrp-custom-recovery , but I'm getting error: partition 'recovery' not support flash.
Lastly I tried with SP Flash Tools, but I can't install drivers. After holding red button 2 seconds and plugging cable there is no device unknown to install drivers or any kind of device looking like this phone.
Can anyone help ?
Thanks
gunlok said:
Hi,
My friend gave me this phone to update the rom, but I'm facing a problem. Device was rooted, recovery is installed, but some really old one - it doesn't even say what kind of recovery it is. So I read that I need to update to TWRP 2.8.4.0 rev.2. Tried flashing it with TWRP apk, but after choosing it and hitting install, it reboots and goes into old recovery and I can't install new TWRP. Then I tried installing it with this guide: http://rootoreviews.com/root-Lenovo-P780-install-twrp-custom-recovery , but I'm getting error: partition 'recovery' not support flash.
Lastly I tried with SP Flash Tools, but I can't install drivers. After holding red button 2 seconds and plugging cable there is no device unknown to install drivers or any kind of device looking like this phone.
Can anyone help ?
Thanks
Click to expand...
Click to collapse
Hi. I have read your message and you have to do this:
First Tutorial.
I see that you have installed allready one custom recovery.
1. Download TWRP from here: http://forum.xda-developers.com/lenovo-p780/help/rooting-tutorial-kitkat-t2835605
2. After download putt the zip file to your root of your internal memory
3. Reboot to your current recovery and install twrp
4. After install power down your phone.
5. Start your phone again with all buttons pressed: Power + Volume up and Volume down.
6. Go to TWRP and do a full backup of your current firmware.
7. After full backup you can install any custom firmware you want.
8. I reccomend latest MIUI from AndreyZO, Mirror 9.
9. Good luck. If you have other questions write here.
Seccond Tutorial
1. Look in this post: http://forum.xda-developers.com/lenovo-p780/help/rooting-tutorial-kitkat-t2835605
2. Download TWRP_v2.8.4.0 rev2 and read twice that tutorial
3. Go to this post and download SP Flash Tool: https://drive.google.com/drive/folders/0B_B98oK4DpK1S1l2bXRkTGxhVFk
4. Go to this post and download latest stock KITKAT and drivers: http://forum.xda-developers.com/lenovo-p780/development/p780-row-s226-flash-flashtool-t2909202
5. When you install the drivers in windows 8,10 you must disable driver signing. Look on youtube.
6. Now you must flash new system.
7. Unpack stock Kitkat firmware.
8. Unpack TWRP.
9. Go to firmware folder and delete recovery.img and replace with TWRP
10. Flash the firmware.
11. After flash boot at least once. If by any chance your phone is Lenovo P780 speed edition, after this flash will not start. This means that you need the latest preloader. Download it from here: http://forum.xda-developers.com/lenovo-p780/help/lenovo-p780-chineese-speed-version-t2874161
12. After flash reboot in recovery by powering off the phone and start with all buttons pressed: Power + Volume up and Volume down.
13. Now you have last stock firmware with custom recovery installed. Go to TWRP and do a full backup of your current firmware.
14. After full backup you can install any custom firmware you want.
15. I reccomend latest MIUI from AndreyZO, Mirror 9.
16. Good luck. If you have other questions write here.
Tried to flash from this weird recovery, but I get error - look at pic.
I didnt flash this recovery, it must've been flashed by seller in my country. It looks like he way buying chinese versions and then flashing modified rom with polish language (very poorly translated).
Problem with sp flash tools is, I cant install usb driver. When Im in download mode I get the sound that usb device has been plugged in and after 1 second i get the unplugging sound. There is no unknown device in Device Manager, do I am not able to update the driver :/
gunlok said:
Tried to flash from this weird recovery, but I get error - look at pic.
I didnt flash this recovery, it must've been flashed by seller in my country. It looks like he way buying chinese versions and then flashing modified rom with polish language (very poorly translated).
Problem with sp flash tools is, I cant install usb driver. When Im in download mode I get the sound that usb device has been plugged in and after 1 second i get the unplugging sound. There is no unknown device in Device Manager, do I am not able to update the driver :/
Click to expand...
Click to collapse
That one is stock recovery. Proceed with the seccond tutorial.
One more question before I try to flash, I got CN verision, u answered to me in different thread:
stympy said:
Hi. Your layout is CN.
Look if you have custom recovery TWRP Installed.
If you have TWRP installed you can go to this post and install latest MIUI MINOVO.
Good luck.
Click to expand...
Click to collapse
So is that ROW Kit Kat ok for me ?
Yes it is ok as base firmware.
After you flash and install TWRP, you can install any custom firmware.
Send from my Lenovo P1 Vibe Pro with 3 Gb of RAM and 32 Gb of Internal Storage.
Ehh now in SP flash tool I get this error... I followed all steps :/
gunlok said:
Ehh now in SP flash tool I get this error... I followed all steps :/
Click to expand...
Click to collapse
Try version 5 and see what happens.
Send from my Lenovo P1 Vibe Pro with 3 Gb of RAM and 32 Gb of Internal Storage.
gunlok said:
Ehh now in SP flash tool I get this error... I followed all steps :/
Click to expand...
Click to collapse
Did you have any success with SP Flash tool v5?
Send from my Lenovo P1 Vibe Pro with 3 Gb of RAM and 32 Gb of Internal Storage.
Hi,
Sorry for delay, wasn't at home during weekend. Im flashing right now, but I had to use "Format all + download", cause only download showed error: "PMT changed for the ROM it must be download". Now I can flash the ROW version of custom rom or CN ?
Hmm I have still stock recovery not TWRP, although I replaced it with TWRP. File size matches perfectly...
Ok, worked but I flashed it with ROW version of recovery, making backup at the moment.
Got an error installing minovo_NOTE_6.12.1_ROW.zip, couldn't boot into recovery after so I decided to flash via SP Flash Tools one more time. After that booted into recovery and once more I have stock recovery xD I'm in serious WTF mode right now
Hmm I think I screwed something. After booting Kit Kat it says "Invalid imei" :/ I guess I will have to restore with MTK droid tools ? Can you guide me through that ?
gunlok said:
Hi,
Sorry for delay, wasn't at home during weekend. Im flashing right now, but I had to use "Format all + download", cause only download showed error: "PMT changed for the ROM it must be download". Now I can flash the ROW version of custom rom or CN ?
Hmm I have still stock recovery not TWRP, although I replaced it with TWRP. File size matches perfectly...
Ok, worked but I flashed it with ROW version of recovery, making backup at the moment.
Got an error installing minovo_NOTE_6.12.1_ROW.zip, couldn't boot into recovery after so I decided to flash via SP Flash Tools one more time. After that booted into recovery and once more I have stock recovery xD I'm in serious WTF mode right now
Hmm I think I screwed something. After booting Kit Kat it says "Invalid imei" :/ I guess I will have to restore with MTK droid tools ? Can you guide me through that ?
Click to expand...
Click to collapse
Hi. Look on this location:
http://forum.xda-developers.com/showthread.php?t=3174563
Send from my Lenovo P1 Vibe Pro with 3 Gb of RAM and 32 Gb of Internal Storage.
Sorry for annoying you once again. When I try to flash anything in TWRP I get error "unable to mount /system". I read that it could mean that system partition might have incorrect file system. What is the standard one for p780?
It happens when I flash the stock KK with TWRP recovery, then I want to flash Superuser. I need superuser to use MTKdroidtools to restore IMEI.
My biggest problem is when I boot the Stock KK after flashing and power OFF, I can't boot to TWRP recovery. Instead it's booting stock recovery. Only way to to boot to TWRP or any custom recovery (tried CWM) is only after fresh flashing with SPflashtools, but I can't flash superuser. If I format /system I can install superuser (no error unable to mount /system), but I have no system to boot to use MTKdroidtools.
This phone is driving me crazy....
UPDATE:
Ok i managed to restore everything, thanks for help. Can't flash custorm rom still but im making different thread.
Hi guys, i got my H9 yesterday and because i thought i read enough on this forums i wanted to unlock it then install TWRP and install superSU to gain root access and stick with the stock firmware.
Unlocking went perfectly fine,phone booted to OS, than i flashed twrp 3.1.1-1 as advertised here and made a factory reset. Phone was stuck in bootloop for unknown reason.
I made several wipes and somehow managed to check all boxes in the wipe menu which erased the whole OS.
Now i read here that others have the "no OS" problem too but because i still have all unlocked fastboot and twrp i wanted to ask which method is best to flash back the original FW.
Which stock ROM is safe to install? i have european H9 is STF-L09C432B170 the right one for me?
Which method is the best to install it? Copy the 3 zips to internal stoagre via OTG device and install it out of twrp? I read that there is also a force method where users can push vol up, vol down and power simultaneously and enter the huawei install force mode.
I am quite sad that the phone was stuck in bootloop after twrp install and still dont know what caused it. When i install it from twrp there are 3 zips: update, data full public , hw eu. In which order do they have to e installed and is one of them overwriting the TWRP recovery?
Please give me a short hint/procedure, im quite afraid that i cant get my phone back to work and it is brand new. I dont know what caused the unsolvable bootloop.
Best regards and many thanks
Hi.
Check this:
https://forum.xda-developers.com/showpost.php?p=73334439&postcount=1
This help you.
Regards
thanks for the hint but i cant find a solution for me there.
ut this
i copied the 3 .zip files to internal today but TWRP doenst allow me to write them it fails with "write err errno 9"
then i tried to copy the update.pp in DLOAD folder on micro sd but this is not possible because filesize is over 2gb. i tried to format micro sd with twrp to exfat but it till doesnt work. please give me a little hint what to do im completely desperate about the situation.
Today i installed Huawei Multitool and extracted the .img file out of the update.app files, i was able to flash all 4, system, boot, recovery and cust.
Now the rec. menu is back to stock and everything got installed but the phone still isnt booting. i think it is because i missed the userdata.img which i cant find anywhere.
Other users here have the same problem. Is there a firmware package which includes all 5 .img data?
Best regards
i found the official huawei service full repair firmware with all necessary files for unbrick (system, cust, recovery, userdata, boot) flashed them via fastboot but stil device is "hanging" after the warning message that its unlocked. i think it is because i wiped vendor data in twrp but i cant flash vendor.img in fastboot. it is included in the fw package but cant be transfered to phone via fastboot. it stops at part 1/2 because the filesize allowd is around 470mb max but the extracted file has a size of 670. anyone know what to do?
Best regards
You need to go via the Rebrand way with no rebrand. I had the same problem and was trying to use the multitool without success. The oeminfo can be flashed alternatively if it fails during the HWOTA process.
https://forum.xda-developers.com/honor-9/help/how-flash-oeminfo-t3657499
ok i download all the folders with the .bat file. Then i download C432B150 from the czech site and add it to the update folder. Than i rename the 3 files accoding to the manual and run the .bat file but without rebranding right?
Des this tool any different than the HuaweiMultiTool or fastboot with flash command?
Best regards
I treid out HWOTA, the first step installing twrp is successful than i disattach usb cable as described and enter twrp. Then it says in twrp i have to connect again and press enter but then the bat file stops and doenst go on. i dont come to the point where i can choose rebrand or flash firmware.
Whats wrong here?
edit: i saw in the .sh file that the script executes wait_adb but my phone is not entering adb mode as it seems when in main screen of twrp. is this normal or do i have to set it manually in twrp
best regards
I was able to install the B130 now via 3 button recovery. Now im on B130 but cant update elsewhere. Also the 2 capacitive buttons are not working. Bootloader is locked again. Everything is stock and the phone runs great. When i update with the 3 buton method from external sd, which firmware should i use? i tried B150 full OTA but it aborts after 5% with an error. Do i only need to get a small OTA package now?
How can i put my cap. buttons back to work? Too bad only the 3 button method worked to recover the phone.
Best regards and many thanks.
I did the HWOTA with b120 firmware and then used firmware finder to update to b150.
The bug with capacitive buttons is present till Oreo. I use the home button gestures anyways.
Hope it helps.
ok, thats bad but they worked with the initial revision of b130 and b150 when i downloaded it OTA. Is this something like a fuse like.knox at samsung which happens at custom flashing?
Sent from my GT-I9300 using Tapatalk
the HWOTA method doesnt work, the batch file gets stuck after connecting the phone in twrp back to computer. in script it says wait_adb but it is not recognized somehow.
do u know a solution? anotherone here got that problem too.
im very afraid of that, i read here that everything related to twrp 3.1.1-0 and 3.1.1-1 is problematic a lot of people cant boot after installing twrp and can wipe whtever they want the phone never boots fully
whats the difference in the B130/B120 the phone came from huawei and the version flashed via tools? when i got it everything worked
i have this version.
ok so install twrp have frq and bootloader unlocked and then do backup out of recovery? with your file? can you provide download link? is this then a zip file?
I want to solve the thread and how i solved problem.
The B130 service firmware by huawei could be installed via 3 button method, than i was able to go up to the newest B180 via firmwarefinder and DNS method but with not working cap. buttons and flash etc.
Yesterday i installed TWRP 3.1.1-1(temporary) via HWOTA.zip method (ireplaced the older twrp in recovery folder) and successfully installed B120 and got the buttons etc working again. Then installed root and now system works fine and is rooted. My mistake was to install twrp over B130 or B150 which i downloaded OTA at the first day i got the phone. I tested this yesterday to install TWRP along with B150 and unlocked bootloader, infinite bootloop again. With B120 the TWRP 3.1.1-1 works out of the box without any loops.
The 2 trouble solvers where B130 service firmware and HWOTA with B120.
The external SD had to be inserted in card reader on PC because of the large filesize of the B130.
I would recommend to everyone before starting to play with the H9 to move the B130 folders to phone while it is still accessible. When everything bricks like in my case and u still have twrp than you can go to twrp main screen and connect phone to computer to rename the folder with B130 to "dload" and arrange update.app accordingly on PC or in TWRP file manager.
Can i set this topic to [SOLVED] myself?
Best regards
https://forum.xda-developers.com/honor-9/development/firmware-huawei-honor-9-stf-l09-stock-t3696892
this works flawlessly with 3 button method
Hello XDA!
I am writing this thread to ask for help rooting my Samsung Galaxy J2 Pro.
I attempted to use apps such as: Framaroot, Kingroot, etc.. but so far none of them have worked and I have not been able to find a working guide on the internet of how to root my phone.
I also tried installing an unofficial version of TWRP for my phone but everytime I tried to boot into the recovery it would say "No Command" and then boot into the original recovery.
Is anyone able to help me root my phone? Can it even be done?
Any help is sincerely appreciated. Thanks!
Phone Specifications:
Samsung Galaxy J2 Pro.
SM-J250G
Android Version: 7.1.1
Bumpity Bump
Try this at your own risk
Make a backup before trying
I got root access with this method
Download stock Rom from sammobile extract and there should be 5 MD5 files extract the AP file with 7z and copied boot.img on to sdcard
Installed MagicalMmanager-7 used it to patch the boot.img to a tar file
Copied the boot image to my pc desktop then flashed the boot with odin
When I booted it back up magisk manager kept crashing so I uninstalled it and installed magiskmanager-5.23 rebooted it opened magisk and followed the prompts to update it
:good:
putzwon said:
Try this at your own risk
Make a backup before trying
I got root access with this method
Download stock Rom from sammobile extract and there should be 5 MD5 files extract the AP file with 7z and copied boot.img on to sdcard
Installed MagicalMmanager-7 used it to patch the boot.img to a tar file
Copied the boot image to my pc desktop then flashed the boot with odin
When I booted it back up magisk manager kept crashing so I uninstalled it and installed magiskmanager-5.23 rebooted it opened magisk and followed the prompts to update it
Click to expand...
Click to collapse
Hello there.
I have tried to patch my boot.img but when I put into a .tar and flash it, it doesn't flash, it's just stuck on file analysis despite being able to flash other files. Would you be able to send me a copy of your boot.img, thanks.
Kindest Regards
-Jayden
JaydenATC said:
Hello XDA!
I am writing this thread to ask for help rooting my Samsung Galaxy J2 Pro.
I attempted to use apps such as: Framaroot, Kingroot, etc.. but so far none of them have worked and I have not been able to find a working guide on the internet of how to root my phone.
I also tried installing an unofficial version of TWRP for my phone but everytime I tried to boot into the recovery it would say "No Command" and then boot into the original recovery.
Is anyone able to help me root my phone? Can it even be done?
Any help is sincerely appreciated. Thanks!
Phone Specifications:
Samsung Galaxy J2 Pro.
SM-J250G
Android Version: 7.1.1
Click to expand...
Click to collapse
Hi Jayden
I've got exactly the same problem. Have you worked this out eventually? Please help!
MC
qichen said:
Hi Jayden
I've got exactly the same problem. Have you worked this out eventually? Please help!
MC
Click to expand...
Click to collapse
Unfortunately I have not found a solution. Please notify me if you find one.
here is a copy of my boot.img after flashing this you will get a verification problem and you will have to reset your phone if it bootloops into recovery or starts to update and says no command take battery out put it back in and boot it again or boot in to odin mode and push down and boot it eventually it will boot in to recovery then factory reset it. first boot may take 5-10 minutes
my software version is J250GDXU2ARD3_J250GXSA2ARD3_XSA
putzwon said:
here is a copy of my boot.img after flashing this you will get a verification problem and you will have to reset your phone if it bootloops into recovery or starts to update and says no command take battery out put it back in and boot it again or boot in to odin mode and push down and boot it eventually it will boot in to recovery then factory reset it. first boot may take 5-10 minutes
my software version is J250GDXU2ARD3_J250GXSA2ARD3_XSA
Click to expand...
Click to collapse
Hello and thanks a lot! I flashed my boot image and now when it boots it says "Set Warranty Bit : Kernel" and an infinite booting screen.
What do I do from here? or do I need to flash the original rom?
don't worry about "Set Warranty Bit : Kernel" mine does it too here is another boot.img after i flashed this i got verification failed so i used 7z to tar userdata.img.ext4 i extracted from the AP image i got the boot.img from.
i put boot in BL and userdata in AP and flashed it. it fired up as normal and then i installed magisk apk
JaydenATC said:
Hello and thanks a lot! I flashed my boot image and now when it boots it says "Set Warranty Bit : Kernel" and an infinite booting screen.
What do I do from here? or do I need to flash the original rom?
Click to expand...
Click to collapse
Flash the original rom then flash boot and userdata as i explain in next post
Hey, sorry for the late response. Everything is working fine! I now have superuser abilities but everytime I try to flash my recovery with TWRP it just loads the stock recovery. I even tried removing certain files from the root folder to avoid the stock recovery being flashed but it hasn't worked.
Any idea? Ps. You are a life saver my man.
JaydenATC said:
Hey, sorry for the late response. Everything is working fine! I now have superuser abilities but everytime I try to flash my recovery with TWRP it just loads the stock recovery. I even tried removing certain files from the root folder to avoid the stock recovery being flashed but it hasn't worked.
Any idea? Ps. You are a life saver my man.
Click to expand...
Click to collapse
glad i could help and i don't think there is an official twrp for this device here is one i ported a couple things still don't work mtp and sideload but it's not really usable until someone ports a rom due to the data encryption which you have to format to be able to flash anything
putzwon said:
glad i could help and i don't think there is an official twrp for this device here is one i ported a couple things still don't work mtp and sideload but it's not really usable until someone ports a rom due to the data encryption which you have to format to be able to flash anything
Click to expand...
Click to collapse
Hello,
Sorry, I don't have the J250G anymore as I traded it for a J5.
Kindest Regards
Jayden
My internal storage showed I only have 8gb instead of 16gb. Is there a fix for this?
P.S. Wiping data fixes it
ok
You can extract it from the AP file from stock firmware using 7z
hey
hey everyone im just wondering but is there a kernel for this device yet or any rom ("J250G")
Hello,
I was wondering if some could help me please. I wanted to flash RR Rom 6.0 on my BLA-L09(I think that what's it is) phone.
I was able to unlock my boot loader, and flash TWRP my device but my dumb s*** flashed TWRP to my file system use FLASH SYSTEM instead of FLASH RECOVERY. Now, I can't fix it ?. I know I can use sideload so I'm not panicking just yet however I know I messed up the file system.
Could someone tell me what file system system I should be using (fat, exfat, ext4, etc...) and what to do to get this think to boot backup.?
I've tried and side loading "update_full_BLA-L29_hw_la.zip" stock ROM but no luck... I keep getting this error message:
"check_write_data_to_partition,write data error
Update_huawei_pkg_from_ota_zip: update package from zip failed
Updated process ended with error: 9"
HELP.!!!
me too..... following searching for a solution
Shandroid_94 said:
me too..... following searching for a solution
Click to expand...
Click to collapse
If you find anything, let me know.!
Just boot to fastboot, flash RR to system and TWRP to recovery_ramdisk?
Would anyone help me get root on doogee bl 12000? This is a version without a pro so this is a different topic than this one.
No kingoroot or framaroot programs work.
I have flashtoola and rom for this phone. I tried using adb to upload files with the 12000 pro doodge but there was always some error.
I also tried to upload files via flashtoola and recovery. However, without success.
Root Doogee BL12000
Hallo there. I'm trying to root my Bl12000. I've got a TWRP from twrp builder. It works, but whatever zip file I'm trying to install I always get "failed to mount data", invalid argument. The twrp also tells me, that there's bo OS installed, but there is. Phone is working fine after reboot. SuperSu can't be installed. Full wipe is not possible, also "failed to mount" and so on.
any help ?
Tia, Chris
I think it's the encryption. Any ideas how to remove it?
Installed twrp via fastboot and sp flash tool, but I can't boot phone into it. Searched dozens of sites, no success. Flashed the twrp again with sp flash tool and according to sp it was successful. I tried several ways to boot the phone into it afterwards, no luck
My goal is to root this phone only. I'm not very experienced so if anyone could please give me a hand here and tell me where or what I'm doing wrong, that'd would be great and much appreciated. Thanks.
Ok. If I flash the twrp with Sp flash tool and type "fastboot reboot" on the adb console, sending the command while I hold vol+ and power-, the phone boots into the twrp. Next time it will be gone, so I have to flash it again. Noticed that, done.
But all this is taking me nowhere, because the encryption still prevents me from installing any zip file or format a partition. Yuck ?
Root Bl12000
Since the SuperSu method took me nowhere I decided to try Magisk. And.......HURRAY !!!!!!.......it worked.....for a moment. Booted the patched boot.img and got superuser. But with the first reboot I got stuck in bootloop. Tried again, in case I missed something, but same ****.
IT WORKS !!!!! My mistake was to assume, that Magisk works the same way as rooting with SuperSu does. So after rooting with Magisk I tried to install root apps as I was used to, but Magisk does not work that way.
Well, it'll take me awhile to figure this out ?
Why does an app keep coming back on my phone after I have done factory reset?
Christian1968.Bolz said:
Hallo there. I'm trying to root my Bl12000. I've got a TWRP from twrp builder. It works, but whatever zip file I'm trying to install I always get "failed to mount data", invalid argument. The twrp also tells me, that there's bo OS installed, but there is. Phone is working fine after reboot. SuperSu can't be installed. Full wipe is not possible, also "failed to mount" and so on.
any help ?
Tia, Chris
I think it's the encryption. Any ideas how to remove it?
Installed twrp via fastboot and sp flash tool, but I can't boot phone into it. Searched dozens of sites, no success. Flashed the twrp again with sp flash tool and according to sp it was successful. I tried several ways to boot the phone into it afterwards, no luck
My goal is to root this phone only. I'm not very experienced so if anyone could please give me a hand here and tell me where or what I'm doing wrong, that'd would be great and much appreciated. Thanks.
Lucky Patcher 9Apps VidMate
Ok. If I flash the twrp with Sp flash tool and type "fastboot reboot" on the adb console, sending the command while I hold vol+ and power-, the phone boots into the twrp. Next time it will be gone, so I have to flash it again. Noticed that, done.
But all this is taking me nowhere, because the encryption still prevents me from installing any zip file or format a partition. Yuck
Click to expand...
Click to collapse
This Recovery is only supported for Doogee BL12000
You should have either PC or Laptop.
Make sure to charge your phone for at least 50%.
Download and install latest Doogee USB Drivers on your PC/Laptop [All Android USB Drivers]
Download the SP Flash Tool Software
VCOM driver: Download – Instal the VCOM Driver on your computer (still compatible with MT67xx phones)
Before flashing a custom recovery, you need to unlock the bootloader on Doogee BL12000
Take a full backup just in case if you need it later
TWRP+root bl 12000
joachim97 said:
Would anyone help me get root on doogee bl 12000? This is a version without a pro so this is a different topic than this one.
No kingoroot or framaroot programs work.
I have flashtoola and rom for this phone. I tried using adb to upload files with the 12000 pro doodge but there was always some error.
I also tried to upload files via flashtoola and recovery. However, without success.
Click to expand...
Click to collapse
On the forum 4pda can be found for bl 12000
TWRP+ROOT
when you install twrp formatting you can not do it, but immediately install magisk and reboot ...