[recovery] twrp for samsung galaxy j7 prime [g610f] - Samsung Galaxy J7 ROMs, Kernels, Recoveries, & Oth

TWRP FOR SAMSUNG GALAXY J7 PRIME (SM-G610F/M)
*** Disclamer
* Your warranty is now void.
*
* We are not responsible for bricked devices, dead SD cards,
* or any other problems u face. Please
* do some research if you have any concerns about features included in this ROM
* before flashing it! YOU are choosing to make these modifications, and if
* you point the finger at us for messing up your device, we aren't to be held reponsible.
Be sure to backup your data,contacts,apps,etc. as the internal storage may need to be wiped
Flashing Instructions
1. Download The Odin flashable Zip
2. Enable OEM unlock in your developer options.
3. Enter Download mode (Vol Down + Home Button + Power Button while switched off)
4. flash the twrp by placing downloaded zip in AP section and flash it while keeping auto reboot off.
5. Once it shows PASS... Press vol down + home + power..
6. when the phone turns off...immediately shift to volume up + home + power.
7. U Will boot to twrp...
8. If you just wanna root... just flash supersu using otg or sideload...
9.if you wanna mount internal ... flash the kernel provided below and Wipe internal... [WARNING : your device will be formatted...make a backup first]
10. Enjoy
FEATURES
1.touch Working
2. f2fs file system support (read, write, format, backup & restore)
3.exFAT file system support (read, write, format, backup & restore)
4.NTFS file system support (read, write, format)
5.ADB root
6.ADB Sideload
7.Full SELinux support
8.OTG support
9. Backup And Restore
10. MTP supported
ISSUES
1. Sdcard Doesnt mount
2. MTP doesnt work
3.Samsung encryption is not supported yet in TWRP 3 (see: https://gerrit.omnirom.org/#/c/17308/)
DOWNLOADS
TWRP - DOWNLOAD
MODDED KERNEL- HERE
CREDITS:
TWRP team..
Samsung
max35000 (for the kernel)

thank you bro..
gooooooooood job
---------- Post added at 03:02 PM ---------- Previous post was at 02:58 PM ----------
it works!!!!!!!Thank you very much brother

dacochir said:
thank you bro..
gooooooooood job
---------- Post added at 03:02 PM ---------- Previous post was at 02:58 PM ----------
it works!!!!!!!Thank you very much brother
Click to expand...
Click to collapse
np still...cant figure out sdcard mounting... but i think otg compensates for that

Varun hellboy said:
np still...cant figure out sdcard mounting... but i think otg compensates for that
Click to expand...
Click to collapse
Yes that's right. Otg cable was detected. There is no need to ADB. Thank you very much brother:good:

MTP fixed

hello, thanks for this one.
TWRP works well, touch screen works.
Since sdcard not detected, how to flash supersu.zip?
I tried method sideload but it doesn't work well.
Difficult to use cmd on windows xp

backup and restore not working

dafikjunior said:
hello, thanks for this one.
TWRP works well, touch screen works.
Since sdcard not detected, how to flash supersu.zip?
I tried method sideload but it doesn't work well.
Difficult to use cmd on windows xp
Click to expand...
Click to collapse
Use otg....or wipe internal...flash kernel and reboot...put supersu in internal and flash

dacochir said:
backup and restore not working
Click to expand...
Click to collapse
Working for me.... I must be doing something wrong.....see attachment for proof

Varun hellboy said:
Working for me.... I must be doing something wrong.....see attachment for proof
Click to expand...
Click to collapse
Should I use a kernel that you have introduced?
I am currently using the ROM DoomsDay I'm gonna get this ROM backup.
Should I install the kernel that you have introduced?
thank you very much brother...:good:

dacochir said:
Should I use a kernel that you have introduced?
I am currently using the ROM DoomsDay I'm gonna get this ROM backup.
Should I install the kernel that you have introduced?
thank you very much brother...:good:
Click to expand...
Click to collapse
yes....it is highly recommended.. use it

guys i have uploaded a new kernel based off latest stock rom....use that as a wifi lag is seen while using max's kernel on Roms like Doomsday....

Is the modded kernel has some features, or just modded to enable to mount the internal storage?

@Varun hellboy. Base on experience, Can u help me build a twrp recovery for j7109 (china version). I cant find out any twrp really working for it. May be it'snt international version. I can provide things as u need. Thank in advanced!

steviejrdn said:
Is the modded kernel has some features, or just modded to enable to mount the internal storage?
Click to expand...
Click to collapse
only allows mounting....i will make a feature packed kernel later..

kien_vip said:
@Varun hellboy. Base on experience, Can u help me build a twrp recovery for j7109 (china version). I cant find out any twrp really working for it. May be it'snt international version. I can provide things as u need. Thank in advanced!
Click to expand...
Click to collapse
Ask J700 guys..

Oh thanks. May be I'll ask guys with j7xxx series.

Is there anyway to backup without USB OTG? i hate to flash the modded kernel also, because it cause a trouble for my stock rom...

thanks

Not Working
not working for me.

Related

[dlx][CWM Advanced Edition] PhilZ Touch

Main thread + features + install instructions + dev support
http://forum.xda-developers.com/showthread.php?t=2201860
PhilZ Touch is a CWM Advanced Edition that adds all the features you could ever miss in CWM
It is a well proven recovery for many phones
It also adds a full touch interface a completely configurable GUI
Please give your feedback, what works, and any bug you could encounter
Read the features, and check if you are missing something
Also, do not forget to read about the powerful aroma file manager integration and double tap shortcut
Download links
Last version can be found here:
HTC Droid DNA (dlx)
http://goo.im/devs/philz_touch/CWM_Advanced_Edition
Click to expand...
Click to collapse
Currently running this on my galaxy note and it works great, putting it on my dna now
is this CWm any faster than the ld one as far as backup and such
CM11 installing works?
thanks!!
How did you guys get this installed?
Just through command line or through another method?
Your help is appreciated
jcyoun33 said:
How did you guys get this installed?
Just through command line or through another method?
Your help is appreciated
Click to expand...
Click to collapse
Flash GUI app
Pretty colors and nice interface. Thanks for this. If you use Flash GUI it will ask you to rename it first. I changed it to "recovery.img" and it flashed no problem.
matteebee said:
Pretty colors and nice interface. Thanks for this. If you use Flash GUI it will ask you to rename it first. I changed it to "recovery.img" and it flashed no problem.
Click to expand...
Click to collapse
is it any faster than the older one ?
About the same as far as backups. I put .hideandroidprogress in clockworkmod folder and my 2.2 gb backup took about 4 mins. Appears to be packed with features I don't know how to use yet but will be quite handy to have.
Can you restore twrp backups or do you need to create new ones?
xlxcrossing said:
Can you restore twrp backups or do you need to create new ones?
Click to expand...
Click to collapse
I was able to restore a TWRP backup when I switched the settings to TWRP mode.
Glad to see this finally making its way to the DNA. Will flash it later today. :sly:
Tapatalked from my HTC Droid DNA
matteebee said:
About the same as far as backups. I put .hideandroidprogress in clockworkmod folder and my 2.2 gb backup took about 4 mins. Appears to be packed with features I don't know how to use yet but will be quite handy to have.
Click to expand...
Click to collapse
Can you link to how to add this mod? Thank you in advance.
nice looking UI, but I can't seem to do adb push blah.zip /sdcard/
not sure why though, because i tried it earlier before i wipe my phone and it worked to seem a small file, but does not work with a larger file size?
I tried it in the twrp beta and it works perfectly fine
this is by far my favorite recovery in all the years ive been a flashaholic.
-DroidIsDNA- said:
Flash GUI app
Click to expand...
Click to collapse
Thanks! Such a dope app!
CM Updater
For those of you that get hasty and install things without reading the FAQ.
Phil3759 said:
CMUpdater cannot flash downloaded files
If you get a /sdcard/0 error, it means you have /sdcard set as /data/media/0 in recovery
The reason is that CM app doesn't support /data/media/0 and is faking recovery with a /sdcard/0 implementation
You still can alter the setting and force it to /data/media in Advanced menu. This will give full compatibility with cwm, CM roms and CM Updater
Click to expand...
Click to collapse
Learn from my mistakes. Also the rude response I got in the 3 minutes before I edited my post in the Philz Recovery thread was the reason people hate this website.
Does this recovery not show up in adb when connected to the PC via USB?
rayjr13 said:
Does this recovery not show up in adb when connected to the PC via USB?
Click to expand...
Click to collapse
ADB works fine for me, make sure you have set the USB connection to Media Device (MTP) under the Menu in Storage
chooven said:
ADB works fine for me, make sure you have set the USB connection to Media Device (MTP) under the Menu in Storage
Click to expand...
Click to collapse
The phone list in adb devices when booted to the rom but in recovery I don't get any connection to it via adb.
MTP works well I used adb to move my backups when booted to the rom but in recovery I could not use adb or adb shell to tinker.
Gonna try the SDK manager to see if I'm out of date or something.

[RECOVERY][2.8] [SLTE][EXYNOS-ONLY] TWRP 2.8 && ClockWorkMod Recovery

Code:
#include
/*
* Your warranty is now void.
*
* I am not responsible for bricked devices, dead SD cards,
* thermonuclear war, or you getting fired because the alarm app failed. Please
* do some research if you have any concerns about features included in this ROM
* before flashing it! YOU are choosing to make these modifications, and if
* you point the finger at me for messing up your device, I will laugh at you.
*/
THIS RECOVERY WILL TRIP YOUR KNOX COUNTER ..AND UR WARRANTY WILL BE VOID
THIS RECOVERY IS ONLY FOR THE GALAXY ALPHA [G850F] [EXYNOS]
PLEASE BE CAREFUL ... THIS RECOVERY HASNT BEEN TESTED "FULLY"...ONLY WIPE CACHE AND DALVIK CACHE , INSTALL ZIP IS TESTED
PLEASE BACKUP YOUR DATA AND MAKE SURE YOU HAVE A BACKUP OF THE FIRMWARE BEFORE PROCEEDING..HAPPY FLASHING!
Why twrp ? Why not a pre-rooted firmware which will not void warranty?
Ans : TWRP has many more functionality than stock recovery ! Rooting means to playing around with your device.If some thing goes wrong it you have to flash the whole firmware again instead,backup your ROM through CWM and if something goes wrong restore your backup AS SIMPLE AS THAT !
All you have to do is follow my instructions :
STEP 1 :
-Download and setup ADB drivers for your device
can be found here Drivers !
STEP 2 :
-Download the recovery from --->
TWRP(more stable)
CWM
-Download odin 3 Link
-Turn of your device and go to odin mode [ Vol down + power + home button (all at the same time) ] release it when you see Galaxy Alpha logo
-Press vol up to confirm
STEP 3 :
-Now that you are in odin mode connect your device via usb cable !
-Now open Odin3 3.09 that you have downloaded.
-If there is a pop-up like Installing ADB drivers let it get finished it is usually updates !!!!
-Make sure the COM : xx (xx is usb port number it can be any number so dont worry about it,just verify COM is lit up)
-Select the recovery (Link in STEP 2) ! Now select AP and browse to where you have .tar file and select it
MAKE SURE U UNTICK THE AUTO-REBOOT BUTTON
-Click Start
ONCE IT SAYS PASS ...REMOVE THE BATTERY ...THEN RE-INSERT THE BATTERY AND BOOT INTO RECOVERY USING VOL UP + HOME + POWER BUTTON
HOW TO ROOT THE DEVICE :
-Download SuperSu (obviously the latest one) from here ------> Click here !
-Copy that to internal sd card
-Power off your device and press vol up + power + home button (all at once)
-Select install zip from sdcard --->choose zip from sdcard ---> scroll down and flash UPDATE-SuperSU-v2.xx.zip
Done ! And you are ready to go
BUGS
YOU TELL ME [/SIZE]
NOTE : IF ANY OPTION DOESNT WORK FOR U ... TURN OFF UR PHONE AND THEN BOOT INTO RECOVERY
SOURCES
DEVICE TREE
KERNEL(PREBUILT ... THANX TO SAMSUNG ... AVAILABLE IN THE DEVICE TREE)
CREDITS
TWRP TEAM
a big thanx to @hensk for testing
CHANGELOG
Code:
[u][i][b][color=red]build 2[/color][/b][/i][/u]
bump to 2.8.1.0
removed config for external sd as no expandable memory
[u][i][b][color=red]build 1[/color][/b][/i][/u]
initial build
last one
exellent job m8,I already make my first nandroid backup to save my rom
now its time to find edemony to make rom for us
10ks for all dude
Wow, this is nice. Not yet ready to trip my knox but I appreciate your efforts anyway! :thumbup:
Sent from my SM-G850F
I already make my first TWRP restor,works like a charm
10ks rut
nEW BUILD IS UP!
Changelog (twrp)
build2
bump to 2.8.1.0
removed external sd support as no expandable memory on the device
rutvikrvr said:
Changelog (twrp)
build2
bump to 2.8.1.0
removed external sd support as no expandable memory on the device
Click to expand...
Click to collapse
How about backup/restore support for external usb flash drive?
neofral said:
How about backup/restore support for external usb flash drive?
Click to expand...
Click to collapse
supports usb otg ??? .. il add it
Will this work for the AT&T version in the U.S.? If not, my apologies!
Jaybell4444 said:
Will this work for the AT&T version in the U.S.? If not, my apologies!
Click to expand...
Click to collapse
what are the specs .. i mean the processor and stuff
rutvikrvr said:
what are the specs .. i mean the processor and stuff
Click to expand...
Click to collapse
Technical Specifications
Battery
Capacity1860mAh
Talk time (hours)Up to 13
Standby time (days)Up to 11.5
Dimensions
Size (inches)5.23x2.58x0.26
Weight (ounces)4.03
Processor
ChipsetQualcomm® Snapdragon™ 801
Cores2.5GHz quad-core
Memory
Internal memory storageUp to 32GB
RAM2GB
Wireless Technology
4G-LTEBands 1, 2, 3, 4, 5, 7, and 17
4GHSPA+ with enhanced backhaul
3G - UMTS850/1900/2100MHz
GSM/GPRS/EDGE850/900/1800/1900MHz
W-Fi Connectivity802.11 a/b/g/n/ac
5GHz Wi-Fi-capable
Near Field Communication (NFC)Open, Secure, Softcard compatible
Bluetooth® technologyv4.0 LE
Mobile Hotspot4Up to 10
FOTA capable - upgrade Firmware Over The Air
Operating System
Android™v4.4 (KitKat)
Display
Display size (inches)4.7
Resolution (pixels)720x1280 HD Super AMOLED®
Colors16 million
Keyboard
Touchscreen
QWERTYVirtual
Predictive text for fast typing
Backlit keys
he mean recovery.img,boot.img & build.prop from Alpha-850 snapdragon
but i think first you should "ask" Chainfire for root
after that should require help hire,this is my opinion
Jaybell4444 said:
Technical Specifications
Battery
Capacity1860mAh
Talk time (hours)Up to 13
Standby time (days)Up to 11.5
Dimensions
Size (inches)5.23x2.58x0.26
Weight (ounces)4.03
Processor
ChipsetQualcomm® Snapdragon™ 801
Cores2.5GHz quad-core
Memory
Internal memory storageUp to 32GB
RAM2GB
Wireless Technology
4G-LTEBands 1, 2, 3, 4, 5, 7, and 17
4GHSPA+ with enhanced backhaul
3G - UMTS850/1900/2100MHz
GSM/GPRS/EDGE850/900/1800/1900MHz
W-Fi Connectivity802.11 a/b/g/n/ac
5GHz Wi-Fi-capable
Near Field Communication (NFC)Open, Secure, Softcard compatible
Bluetooth® technologyv4.0 LE
Mobile Hotspot4Up to 10
FOTA capable - upgrade Firmware Over The Air
Operating System
Android™v4.4 (KitKat)
Display
Display size (inches)4.7
Resolution (pixels)720x1280 HD Super AMOLED®
Colors16 million
Keyboard
Touchscreen
QWERTYVirtual
Predictive text for fast typing
Backlit keys
Click to expand...
Click to collapse
This one is only for exynos
i just flashed build 2 and did my first ever nandroid backup on my SM-G850F :good:
thanks for your work.
since our device don't have sd card slot, i think it would be amazing if we could use the usb OTG and use external USB drives for backup/restore and flashing files. i hope build 3 will be up soon :fingers-crossed:
to use OTG will be nice & usefull,I agree
rutvikrvr said:
HOW TO ROOT THE DEVICE :
-Download SuperSu (obviously the latest one) from here ------> Click here !
-Copy that to internal sd card
-Power off your device and press vol up + power + home button (all at once)
-Select install zip from sdcard --->choose zip from sdcard ---> scroll down and flash UPDATE-SuperSU-v2.xx.zip
Done ! And you are ready to go
Click to expand...
Click to collapse
This will not root your device! You should give link to CF-Autoroot (find your device here: http://autoroot.chainfire.eu/#odin) and not to SuperSU!
200mpx said:
This will not root your device! You should give link to CF-Autoroot (find your device here: http://autoroot.chainfire.eu/#odin) and not to SuperSU!
Click to expand...
Click to collapse
This true? So root through zip flash not possible, need to do it with the odin contained within the chainfire zip?
Redsandro said:
This true? So root through zip flash not possible, need to do it with the odin contained within the chainfire zip?
Click to expand...
Click to collapse
I have not seen a kernel with root for instance that you can flash in recovery.
Happy
Hi,
i just flashed build 2 and it works like a charm on my SM-G850F (BNK1 Stock DBT) :good:
thanks for your work.
best regards

[RECOVERY][EXYNOS] TWRP 3.1.1 (SM-G850F) - UPDATE: 2017-11-30

This is the thread for the TWRP 3.0 recovery for Samsung Galaxy Alpha (SM-G850F). The recovery uses a kernel built from the Samsung sources with root prevention disabled. It is fully working but still be careful and make backups!
DOWNLOAD
XDA:DevDB Information
recovery_twrp_slte, Tool/Utility for the Samsung Galaxy Alpha
Contributors
modpunk
Source Code: http://git.cryptomilk.org/projects/android/android_device_samsung_slte.git/
Version Information
Status: Stable
Current Stable Version: 3.1.1-2
Stable Release Date: 2017-11-30
Created 2014-11-06
Last Updated 2017-11-30
CHANGELOG
2017-01-26
Some bug fixes
Supports sltexx, slte and slteskt
2016-02-13
Update to version 3.0.0-0
Cleaned up device tree
Nicer fonts
2015-09-02
Set SELinux to permissive mode on boot
2015-09-01
MTP and ADB Support
Improved UI with better fonts
2014-11-10
USB OTG support (backup to external usb drive)
2014-11-06
Initial release
Thanks for your work. Glad to you in our device forum.
1 question, does your recovery include support for usb otg? In other words is it possible to backup/restore from usb flash drive?
neofral said:
Thanks for your work. Glad to you in our device forum.
1 question, does your recovery include support for usb otg? In other words is it possible to backup/restore from usb flash drive?
Click to expand...
Click to collapse
I haven't tested it. Does TWRP support this by default? If yes then we should get it working ...
P.S.: I've ordered a USB OTG cable now ...
modpunk said:
I haven't tested it. Does TWRP support this by default? If yes then we should get it working ...
P.S.: I've ordered a USB OTG cable now ...
Click to expand...
Click to collapse
officially yes. check it out here http://teamw.in/project/twrp2
neofral said:
officially yes. check it out here http://teamw.in/project/twrp2
Click to expand...
Click to collapse
OK. It doesn't work cause USB_OTG is not compiled in the kernel. The question is if the SoC has a USB OTG controller...
modpunk said:
Please try it. I will investigate once I got the USB OTG cable.
Click to expand...
Click to collapse
i just tried. the drive is listed as sd card. it has 0MB available even though my usb drive is an empty 32 gb drive formatted with fat32. when i select it for the backup, the selection goes dimm for couple of seconds and comes back back without it being selected and no error message.
by the way, is it possible to do a screenshot with TWRP?
neofral said:
i just tried. the drive is listed as sd card. it has 0MB available even though my usb drive is an empty 32 gb drive formatted with fat32. when i select it for the backup, the selection goes dimm for couple of seconds and comes back back without it being selected and no error message.
by the way, is it possible to do a screenshot with TWRP?
Click to expand...
Click to collapse
The /sdcard folder is normally pointing to /data/media/0.
modpunk said:
The /sdcard folder is normally pointing to /data/media/0.
Click to expand...
Click to collapse
can you change it to point to mnt/UsbDriveA?
this is the path where i see the usb drive via root explorer
EIDT: i have Xperia V device with latest TWRP, i did a backup and restore without any glitches
neofral said:
can you change it to point to mnt/UsbDriveA?
this is the path where i see the usb drive via root explorer
EIDT: i have Xperia V device with latest TWRP, i did a backup and restore without any glitches
Click to expand...
Click to collapse
Looking at the ROM it should be /storage/UsbDriveA maybe we need to create that folder first ...
Maybe you can test this. Boot into recovery, connect to it with 'adb shell' or use twrp terminal and create the directory "/storage/UsbDriveA". Then attach the usb drive.
modpunk said:
Looking at the ROM it should be /storage/UsbDriveA maybe we need to create that folder first ...
Maybe you can test this. Boot into recovery, connect to it with 'adb shell' or use twrp terminal and create the directory "/storage/UsbDriveA". Then attach the usb drive.
Click to expand...
Click to collapse
didn't work. couldn't connect with adb shell when on recovery (maybe not correct drivers insatlled). when creating /storage/UsbDriveA, attached usb drive and it's empty and doesn't list the drive in the storage options.
however, when browsing with root explorer a folder like that already exists
Will it work exynos varient of Galaxy alpha thats available in India with Model No. 850Y?
shranav said:
Will it work exynos varient of Galaxy alpha thats available in India with Model No. 850Y?
Click to expand...
Click to collapse
Try it and find out! I will probably not get a phone from India ....
Recovery with USB OTG support has been updated!
modpunk said:
Recovery with USB OTG support has been updated!
Click to expand...
Click to collapse
is it different from the one i tested couple of days ago (on 7th)? if it's the same, no need to flash for me. i'm happy to have USB OTG support and being able to backup/restore on usb. i have to admit, the internal storage is full already. that's why i needed this support. thank you for enabling this :good:
Is it the G-850FQ?
savasdok said:
Is it the G-850FQ?
Click to expand...
Click to collapse
this thread on the title it says it's for SM-G850F. it's also tested to run well on 850F.
if you want ot test on FQ, you're welcome. if you test, please post back and confirm if it works :good:
anybody have problems with download ,I rich 99% of file & downloading stop
I dont know is this happend to me only or is site problem!!
---------- Post added at 18:00 ---------- Previous post was at 17:55 ----------
Sorry,problem was on my download manager
neofral said:
this thread on the title it says it's for SM-G850F. it's also tested to run well on 850F.
if you want ot test on FQ, you're welcome. if you test, please post back and confirm if it works :good:
Click to expand...
Click to collapse
Got it, thanks.
Will this work with the 850A? Thanks

[TREBLE][ROM] How to install Android P sGSI on cedric

Code:
/* Your warranty is now void.
*
* We're not responsible for bricked devices, dead SD cards,
* thermonuclear war, or you getting fired because the alarm app failed. Please
* do some research if you have any concerns about features included in this TREBLE
* SUPPORT before flashing it! YOU are choosing to make these modifications, and if
* you point the finger at us for messing up your device, we will laugh at you.
*
*/
Install Instruction:
Flash this TWRP with treble support (thx to @CodeZero)
Format /system, /data and /cache
Install this Lineage treble build from Google Drive or from Transfer.sh
Install Android P DP5 sGSI
Mount vendor on TWRP
Install the POST-sGSI zips in the order from Here
Install POST-sGSI-v1.1-cedric from Here
Reboot
Install Google Play Services using either your pc ($ adb install -r .apk), or your phone.
Reboot again
Enjoy
Known issues:
Same as lineage treble and:
MotoActions crash
Only DP3 boots Fixed by @J0SH1X on POST-sGSI-v1.1-cedric
You tell me
How to report bugs:
REGISTER IT ON GITHUB WITH LOGS, OTHERWISE IT WILL BE IGNORED AND CLOSED.
The GitHub for registering the issues is This
Steps to do it:
Check if it was already posted (duplicates will be closed)
Logs should be attached (posted on gist, otherwise the issue will be closed)
The title format should be: LineageTrebleBuildDate: Android-P DP3: issue you are having
The description should be the full log on gist (https://gist.github.com), and steps to reproduce the issue.
Each issue should be posted individually
DONT TAG ME HERE, OR ON TELEGRAM. I use github bot which sends me notifications when someone posts or replies to an issue
IF YOU DIRTYFLASHED, MENTION IT
Requirements for taking logs:
A PC with adb and the drivers installed
A phone
How to take logs:
Connect your phone to the PC
Enable Android debug bridge on the developer settings
Run $
Code:
adb devices
on your PC shell, and if it shows your device proceed, otherwise tag an admin to help you
Run $
Code:
adb reboot
this will reboot your phone
While it's still on the Motorola logo, run $
Code:
adb logcat > log
Once the device boots, replicate the issue
After the issue is replicated, press the CTRL and C keys simultaneously
Once this is done the file log will appear in the folder you ran adb.
This file contains the log.
More info:
Original P thread
Wiki/FAQ
Cedric Wiki/FAQ
Thanks @erfanoabdi for his work on this unbelieveable acomplishment
reserved
ı am ınstall dp5 not boot
AsusZenFone3Deluxe said:
ı am ınstall dp5 not boot
Click to expand...
Click to collapse
I understand that only DP3 works
I try DP4 and DP5; doesn't boot in that Versions
AsusZenFone3Deluxe said:
ı am ınstall dp5 not boot
Click to expand...
Click to collapse
"Issues
only DP3 boots"
read op next time
yes I managed to install on my device, working fine, but camera on record more on others is good, so far ....
---------- Post added at 02:06 AM ---------- Previous post was at 01:19 AM ----------
https://github.com/erfanoabdi/P_semiGSI/wiki/Moto-G5
They just put that you can now install DP4 and DP5, more than correction and need to install?
---------- Post added at 02:56 AM ---------- Previous post was at 02:06 AM ----------
I installed the hevc + sm mod in the magisk, and the Asus camera version 5.0 and now I am able to make video.
Shadowsleeper said:
yes I managed to install on my device, working fine, but camera on record more on others is good, so far ....
---------- Post added at 02:06 AM ---------- Previous post was at 01:19 AM ----------
https://github.com/erfanoabdi/P_semiGSI/wiki/Moto-G5
They just put that you can now install DP4 and DP5, more than correction and need to install?
---------- Post added at 02:56 AM ---------- Previous post was at 02:06 AM ----------
I installed the hevc + sm mod in the magisk, and the Asus camera version 5.0 and now I am able to make video.
Click to expand...
Click to collapse
I updated the thread
If I want to go back to my oreo rom after installing this GSI, do I have to also backup /vendor and then restore it after installing android P? I just don't want to mess up anything since I'm kinda downgrading and I'm assuming these post GSIs somehow patch the vendor partition...
Android p dp5 booted. THANKS
Screenshots
https://androidfilehost.com/?w=files&flid=280192
please update op.released android p stable version
How to install update?
İnstall the image with twrp(system image)
Led flash not working and dont take a video
LTE not working
vimicius said:
LTE not working
Click to expand...
Click to collapse
working my device
AsusZenFone3Deluxe said:
Led flash not working and dont take a video
Click to expand...
Click to collapse
You can just enable camera2api and disable it again and flashlight will work again
Need to explain that you have to extract Android P DP5 sGSI and install as system image, because it lacked that information I stayed vary hours trying to install as zip
Hi,
I want to try out Android Pie with Treble Support - is it possible and uncomplicated to switch back to an Android 8.1 ROM after you flashed the alternative TWRP with Treble-Support + POST-sGSI zips?
ciao, Sören
Deleted.
AsusZenFone3Deluxe said:
working my device
Click to expand...
Click to collapse
friend, how do I run lte?

TWRP Flame [Official]

[RECOVERY] TWRP 3.5.0-0 - TeamWin Recovery Project
Introduction:
Team Win Recovery Project or TWRP for short, is a custom recovery built with ease of use and customization in mind. We started from the ground up by taking AOSP recovery and loading it with the standard recovery options, then added a lot of our own features. It's a fully touch driven user interface , no more volume rocker or power buttons to mash. The GUI is also fully XML driven and completely theme-able. You can change just about every aspect of the look and feel.
Key Features:
Touchscreen driven with real buttons and drag-to-scroll
XML-based GUI that allows full customization of the layout true theming!
Settings are saved to the sdcard and persist through reboots
Ability to choose which partitions to back up and which to restore
Ability to choose to compress backups now with pigz (multi-core processor support for faster compression times)
Onscreen keyboard
Easy selection of internal/external storage
In addition to the above new features, TWRP features a scripting engine that allows an app to send commands to the recovery for the recovery to perform during startup. We call this scripting engine OpenRecoveryScript. This engine will be put to use immediately in the GooManager app. GooManager will be able to install recoveries automatically for most supported devices. The app will also let you choose to install multiple zips from within Android, wipe, and run a backup.
We are looking for other talented developers, themers, and device maintainers if they are interested in helping with a free, open source project.
Source Code:
GitHub - https://github.com/TeamWin/android_bootable_recovery
Gerrit Instance - http://gerrit.twrp.me
If you have made your own TWRP build for an unsupported device, please let us know. We might add your build to the list of unofficial builds. Bear in mind that we are working hard to add more devices and we may add your device to our official build list later.
flame Device Config: https://github.com/bigbiff/android_device_google_coral
DOWNLOAD:
Please go to https://twrp.me to download the device image.
A11 Testing:
https://build.twrp.me/test/flame/twrp-3.6.0-0-test1-flame.img- updated for lineage-18.1 booting
Old info:
Hello, this is a test build for flame users (will work on coral crosshatch/blueline later). The image is pretty safe for backing up now.
So far I have decryption working, touch, adb and backup and restore seems to work. Super partition volumes can be mounted, and the super partition can be backed up.
Not working: sideload and fastbootd
May FW Date https://build.twrp.me/test/flame/twrp-3.3.1-0-test1-flame.img
June FW Date https://build.twrp.me/test/flame/twrp-3.4.0-0-test1-flame.img
July FW Date https://build.twrp.me/test/flame/twrp-3.4.0-0-test2-flame.img
July FW Date https://build.twrp.me/test/flame/twrp-3.4.0-0-test4-flame.img
- fix super partition restore
- fix persist partition restore
July FW Date https://build.twrp.me/test/flame/twrp-3.4.0-0-test5-flame.img
- allow repacking of TWRP boot.img
- magisk currently doesn't work
August FW Date https://build.twrp.me/test/flame/twrp-3.4.0-0-test6-flame.img
August FW Date https://build.twrp.me/test/flame/twrp-3.4.0-0-test7-flame.img
- fix repacking TWRP with magisk
August FW Date https://build.twrp.me/test/flame/twrp-3.4.0-0-test8-flame.img
- multiuser decryption support
- fastbootd support
3.5.0-0: Android 11 bringup
https://build.twrp.me/test/flame/twrp-3.5.0-0-test1-flame.img
https://build.twrp.me/test/flame/twrp-3.5.0-0-test2-flame.img
- Titan M Wipe working on Format Data
- Apex fixes for flattened directories
- Credit to @Freak07 https://github.com/freak07/FLORAL - using his kernel as a Coral/Flame TWRP base
http://twrp.me
What to backup
* super
* data
* persist
* boot
* any other partition desired
What to restore
* super
* data
* boot - depending on ROM support
Please just restore persist if you have a failed partition. I do not recommend restoring backups from phone to phone unless you know what you are doing.
Repacking TWRP into Boot partition
To repack TWRP into the boot partition to override stock recovery when rebooting to recovery, perform the following steps
1. adb push <latest_boot.img> /sdcard/
2. reboot to bootloader and fastboot latest boot.img of TWRP
3. Go to Install
4. Touch Install Image
5. Select your boot.img from /sdcard
6. Swipe to confirm flash
7. Reboot to recovery and android to verify installation
TWRP won't Boot?
Make sure you have a kernel that supports the R DTBO and LZMA ramdisk starting with test5 such as https://forum.xda-developers.com/pi...nel-kirisakuraq-1-0-0-pixel-4-xl-aka-t3992213
Is this just for flame? Or both coral and flame? Reason I ask is because the 2 devices have significant differences, and if it's just for flame, you'll want to throw it in the regular Pixel 4 subforum
This is for flame as described. I will work on coral next.
They share the same device tree btw.
Weird I thought I chose pixel 4 forum. Asking for this thread to be moved.
bigbiff said:
Weird I thought I chose pixel 4 forum. Asking for this thread to be moved.
Click to expand...
Click to collapse
Ah man lol got me all excited!
Thanks long awaited :good:
Will try later..
ok fastboot boot boots fine to TWRP but decryption wont work for me
https://paste.omnirom.org/view/e9536f05
Can confirm this works for flashing. Booted the image and then ADB pushed magisk and kernel and both flashed successfully!
Will try removing lockscreen security next attempt to gain access to internal storage which should likely work.
Great work to see, we are finally not tied to magisk for flashing things now
Mrcactuseater said:
Will try removing lockscreen security next attempt to gain access to internal storage which should likely work.
Click to expand...
Click to collapse
wont work to @my end
2WildFirE said:
Thanks long awaited :good:
Will try later..
ok fastboot boot boots fine to TWRP but decryption wont work for me
https://paste.omnirom.org/view/e9536f05
Click to expand...
Click to collapse
Can you paste logcat output too?
Please guys don't just say it doesn't work. I need recovery.log and logcat so I can debug issues.
2WildFirE said:
wont work to @my end
Click to expand...
Click to collapse
Can you please post recovery.log and logcat?
bigbiff said:
Can you please post recovery.log and logcat?
Click to expand...
Click to collapse
Yep
Is ADB logcat -l the correct one?
2WildFirE said:
Yep
Is ADB logcat -l the correct one?
Click to expand...
Click to collapse
I usually do in adb shell
logcat > /tmp/logcat.txt
Then adb pull /tmp/logcat.txt
OK here logcat https://paste.omnirom.org/view/9caa8b33
And recovery.log https://paste.omnirom.org/view/3c26a706
hope it helps
2WildFirE said:
OK here logcat https://paste.omnirom.org/view/9caa8b33
And recovery.log https://paste.omnirom.org/view/3c26a706
hope it helps
Click to expand...
Click to collapse
Can you tell me your android build version?
bigbiff said:
can you tell me your android build version?
Click to expand...
Click to collapse
qq3a.200605.001
just to thank you a lot bigbiff for putting so much work and efforts on this, you are great. hope you can sort this out, best luck!! (a p3 user) :fingers-crossed::good: sorry for the ot
2WildFirE said:
qq3a.200605.001
Click to expand...
Click to collapse
There was an update to the platform version, please test https://build.twrp.me/test/flame/twrp-3.4.0-0-test1-flame.img
bigbiff said:
There was an update to the platform version, please test https://build.twrp.me/test/flame/twrp-3.4.0-0-test1-flame.img
Click to expand...
Click to collapse
Thanks will try :good:
@bigbiff
yeah decryption works fine now
@bigbiff
Sorry for dump questions, but if I want to backup, is it enough to backup super and data partition?

Categories

Resources