S5 SM900T Gyroscope issue and then Green annoying flash - T-Mobile Samsung Galaxy S 5

I bought the S5 phone a few weeks before Xmas. The first one there was issues so I took it back and got the one I have now. Everything worked fine until one day the gyroscope stopped working. I was so angry because of course there is no store warranty anymore and it's a new phone! I know people say this, but I didn't drop it, no water, no over heating. It just stops working.
I read all the stuff that I could online, nothing worked for the long haul. Was told that I would have to replace the motherboard, because it was a hardware issue.
I finally one day I got really frustrated. It worked before all the updates, then as soon as Lollipop was on, the gyroscope stopped working. It made no sense to me that it's the device. So I rooted it and put Resurrection Remix N. It worked wonderfully. No issues with the Gyroscope at all for the week I ran RR N. But then there was this green flashing thing that was happening that was equally annoying. It would do it just before the phone went to sleep. Drove me nuts. Didn't do it in stock rom, but I read that it means I need to replace the screen??? Tinkering around a bit, I think it's the SD card. At least I hope its the SD card, because that ROM rocks! I have reformated the SD card and the phone works great, then it starts flashing green stuff again at the bottom of the screen. I have a few entries on the forum for the ROM but until I can figure other factors it may be
So, then I have to go back to Stock ROM. Thought I could just flash 4.4.2 on it and call it a day until my SD card comes in. But there are system stop errors that leaves the phone unusable. So I have update the phone all the way up to Marshmallow.
So until I can get a good SD card in and try out RR N again. Could anyone give me ideas on why the gyroscope works flawlessly on RR N but not on the stock ROM? I don't get it?
Thanks in advance for any ideas.

I am cerrtain its not a gyroscope issue, its something in the Stock ROM, because it does work great on RR N

That was my thinking but it's happening. It works perfectly on RR N rom but stops working on Stock rom.

Updating.
Flashed the stock ROM again, just to prove a point that yes indeed the gyroscope stops.
In the stock ROM the screen does not flash at all. But the gyro was ticking me off.
I ended up trying Lineage OS 14.1 and the gyroscope has worked flawlessly. But now the green flicker on the bottom screen is happening.
So recap
Stock ROM: gyro stops working, screen works great
Custom ROM: gyro works and is very responsive green flicker happens before the phone sleeps.
So this does show that yes gyro can have issues in the stock ROM and that its not a hardware issue.
Does anyone have any other ideas.
Thanks.

i'd try BNH5 stock rom from sammobile (4.4.2)

Related

[Q] Rebooting if screen left on for too long

Hey XDA People!.
I have an S-Off HTC EVO 3D GSM
Originally had LeeDrOiD on my phone working fine, did a full wipe and updated to LeeDrOiD 9th January on my phone and found that if my phone screen was on for too long it would reboot. This also happens when i play games, web browsing or during phone calls. i will get around 10 reboots a day. I just switched Roms to ROMeOS3D. thought that might have changed things but still get the same thing.
I found that if my screen was on for longer than around 25seconds and wasn't doing anything(didnt touch the phone) it would freeze and then reboot. If i put the phone on standby no problems but i cant keep turning off my screen every time i have a phone call or every time i put my phone down. web browsing gets frustrating!
Any help would be great! thanks in advance XDA!
So still having this problem but now just happens less and doesn't reboot just turns off.. i have learnt to work around it a little. when i get phone calls i turn off the screen and i make sure i turn off the screen when i put my phone down. but still!! this is retarded!
So now when i go to work and put the phone in my pocket it will turn off. i only realise when i need to check the time.
anyone have any similar problems at all might help?
Have you tried to go to a stock rom? Just to test to make sure it isn't hardware related.
Hey Guys
thought i would update. last night tried out all of the ICS roms out and surprisingly my reboot issues went away. Flashed back to 3 other roms and reboot problem came back. i dont know what it is but the ICS roms fix my reboot issues.
so now Im using the [ROM/WIP/DEV] EVO 3D GSM/CyanogenMod 9 Unofficial v1.2 [ICS 4.0.3] 17.02.201 and no problems. obviously some glitches here and there. but sms, phone calls & internet work so im a happy.
Reaper Thanks for your reply. i did go back to stock and everything was working fine. so its not hardware related. however thanks for your reply. much appreciated!
sabaselection said:
Hey Guys
thought i would update. last night tried out all of the ICS roms out and surprisingly my reboot issues went away. Flashed back to 3 other roms and reboot problem came back. i dont know what it is but the ICS roms fix my reboot issues.
so now Im using the [ROM/WIP/DEV] EVO 3D GSM/CyanogenMod 9 Unofficial v1.2 [ICS 4.0.3] 17.02.201 and no problems. obviously some glitches here and there. but sms, phone calls & internet work so im a happy.
Reaper Thanks for your reply. i did go back to stock and everything was working fine. so its not hardware related. however thanks for your reply. much appreciated!
Click to expand...
Click to collapse
Glad it wasn't hardware man Sometimes stock is the way to go to confirm a hardware issue of just software or rom issues

Touch Screen Issue HTC Incredible & Custom Roms

Okay so this is my first post on XDA and I hope it's in the right section. Anyways I bought an HTC Incredible off a collegue of mine about two weeks ago. I got the phone and immediately rooted and installed a custom rom (MIUIv4 to be exact) I noticed after a lil while that the touch screen would randomly go berserk clicking things, calling people, etc (usually right after turning screen on) When the screen starts doing it I'd turn it off and back on and it would be completely fine. I thought to myself "maybe it's just a problem with MIUI and installed PONS CM7. I still had the same issue. Now whats strange about all of this is if I'm running an RUU or Stock based rom the screen NEVER acts up. I've read on several forums that this is a hardware issue but most people still experience it on stock roms, this is not the case with me. I won't deny that it could be a hardware issue, but it's an issue that can be solved with kerenl/dirvers/software. I'm wondering if I can use the drivers and software from a stock based rom to combat the issue and make custom roms run like they are supposed to. In all of my research I found this link which seems to be pretty promising but I don't know where to begin with it. Unfortuneately I can't post a link until I've posted 8 times, uuugh.
Edit: It seems the longer I run a custom rom the more frequently the issue happens.
If anybody is intrested in helping it would be greatly appreciated. I've been racking my head for over a week on this one. You can look up the blog I read on google. It looks like it could solve my problem.
Unresponsive touchscreen of Nexus S solved by tuning kernel

[Q] Trouble from CM10 back to Stock....very slow!

I had a stock EVO 4G LTE running ICS, I upgraded OTA to Jellybean....had problems with the proximity sensor after the upgrade, so I put CM10 stable on it - and that worked fine for a month. Worked very well actually!
For curious reasons, I wanted to go back to the stock ROM and see if I was just imaging the issues (which Im not, others have reported), so I downloaded the "RUU_JEWEL_CL_JB_45_S_Sprint_WWE_3.15.651.16_Radio_1.12.11.1119_NV_2.87_003_25007_release_299302_signed"
I relocked the bootloader and installed the RUU. Installed fine. However, the phone was SUPER slow. The camera had problems too...but for example, Id make a call and it would ring and call time start, but 10 seconds later the phone would vibrate indicating the call went thru, even though I was a good 4-5 rings in.
So I went back to CM10 - the same exact version I went to before. It was still on my SD Card. Totally unstable. Freezing, rebooting, screen goes blank for no reason...just all sorts of weird problems. Would freeze and reboot during a call, but the caller would still be on the line!
I reflashed the ROM like 5 times, ever time clearing cache, davlik, factory reset, and system. Still completely goofy.
I read there was a problem with the 3.15 RUU, so I followed these directions here.
http://forum.xda-developers.com/showthread.php?t=2097150
But that still didnt help.
Right now Im back on the STock JB ROM. At least I can take phone calls with it, but I'd like to return to CM10.
Any suggestions would be VERY apprecaited!
Thanks.
More things I am noticing:
The Flashlight app doesnt work anymore
Camera doesnt work then causes the whole phone to become unresponsive.
Bump!
Can anybody help me out? Im dying over here without a phone that works.
the phone app keeps crashing. If i reboot, things work ok UNTIL I make a phone call....then nothing works.
Very strange!
I would try wiping 3 times
Sent from my EVO using Tapatalk 2
---------- Post added at 09:44 AM ---------- Previous post was at 09:35 AM ----------
Also are you restoring things from the titanium backup?
Sent from my EVO using Tapatalk 2
MerkoPCS said:
I had a stock EVO 4G LTE running ICS, I upgraded OTA to Jellybean....had problems with the proximity sensor after the upgrade, so I put CM10 stable on it - and that worked fine for a month. Worked very well actually!
For curious reasons, I wanted to go back to the stock ROM and see if I was just imaging the issues (which Im not, others have reported), so I downloaded the "RUU_JEWEL_CL_JB_45_S_Sprint_WWE_3.15.651.16_Radio_1.12.11.1119_NV_2.87_003_25007_release_299302_signed"
I relocked the bootloader and installed the RUU. Installed fine. However, the phone was SUPER slow. The camera had problems too...but for example, Id make a call and it would ring and call time start, but 10 seconds later the phone would vibrate indicating the call went thru, even though I was a good 4-5 rings in.
So I went back to CM10 - the same exact version I went to before. It was still on my SD Card. Totally unstable. Freezing, rebooting, screen goes blank for no reason...just all sorts of weird problems. Would freeze and reboot during a call, but the caller would still be on the line!
I reflashed the ROM like 5 times, ever time clearing cache, davlik, factory reset, and system. Still completely goofy.
I read there was a problem with the 3.15 RUU, so I followed these directions here.
http://forum.xda-developers.com/showthread.php?t=2097150
But that still didnt help.
Right now Im back on the STock JB ROM. At least I can take phone calls with it, but I'd like to return to CM10.
Any suggestions would be VERY apprecaited!
Thanks.
Click to expand...
Click to collapse
i say you should flash MEANBEAN, its a stable JB rom and some of the bugs like the proximity sensor have been fixed thanks to the devs here at XDA. its running very smooth for me. the only issue for me is that google's navigation doesnt work, but telenav works just fine. just wipe your phone about 3 or 4 times (i always do that to ensure i get a clean install on any rom). good luck!
I would re-download CM10 and verify checksum since you didn't mention that.
Sent from my EVO using xda app-developers app
Thanks for the replies.
Really all I want to do at this time is go back to stock, which I currently am on.
But even on the stock 3.15 ROM, it is very very unstable. The phone is majorly delayed. I get 1 ring on incoming calls before it goes to voicemail - but the person calling hears the normal 5-6.
For CM10, I used the same zip file (stayed on my SD card) that I used without problem for almost a month.
I took the phone to sprint (back to stock) and they couldnt figure it out. Getting a replacement tomorrow.
Could I just have a coincidental hardware problem? Seems odd if that is the case, the phone was working perfectly until I went back to stock using the 3.15 RUU
I got my replacement phone last night, did an OTA upgrade to JB in the store and the proximity sensor didnt work...
was about to tell the rep to just order me a GS3, but I said hold off....I really prefer the 4GLTE over the S3
Went home and flashed Meanbean......WOW!
Just like stock, and the prox sensor works!
so my plan is to just keep this ROM until HTC fixes the issue in their next maintenance release.
in TWRP, i made a backup and selected all the options Is this sufficient to get me back to stock, then do an OTA upgrade for the maintenance release, if and when it comes out?

[Q] [Please Help] Weird hardware issue?

Hi everybody,
I'd like to hear your thoughts on my problem.
I have been flashing my i9300 since the day I have it. I wasn't impressed with stock TouchWiz (4.1 I believe?) I have been switching between TW based and AOSP roms alot. I just never found the rom I liked. All of them began to run slow, if they were not already slow. (I do not blame any of the roms I have used, I want to point that out)
Recently I sent the phone back for repair, because it had a burnt in screen. So I went ahead and flashed full stock and reset the counter and all the fun stuff. When I rebooted the phone (100% clean wipe, flashed a Netherlands rom) I noticed that the phone was slow as living h*ll. I had flashed it to a "out off the box" experience but the phone was just about useless. I went ahead and flashed a different Netherlands rom, which was a tad bit faster. I went with it and sent it back.
When I received the phone back in my mailbox, they had flashed stock again (why would one flash stock if just the screen had to be replaced?). I noticed that the phone was extremely slow again!
I decided to believe that it was TW to blame, and flashed Omni KitKat. This was fine for about a week, after which the phone would randomly lock up and system.apk began to crash every 30 minutes or so.
I then decided to start with a clean plate and flashed CM11 (full wipe, including media and all). I have been using that for a little over 2 months now, but the same issues are starting to occur. I have tried it without any 3rd party apps installed, without success. The phone locks up about every 5 minutes with the screen on, I can't listen to music (Google Music or PowerAMP) and then switch to another app, because the music will then stop. If I press the home button, there is an 3-10 second delay, after which system.apk decides to reload along with the launcher (Google Now Launcher), things like that. Sounds like a memory problem to me.
I think it might have something to do with a baseband issue, because of the fact that I have had problems similar before, which were (sort of) solved by flashing a different baseband. But I don't think that Sammy's basebands are compatible with CM11, and I have yet to come across a problem with a CM11 baseband on the internet.
Do any of you experts know an explanation to my problem? Would you suggest sending the phone back for repair?
Thanks in advance
FistFull95 said:
Hi everybody,
I'd like to hear your thoughts on my problem.
I have been flashing my i9300 since the day I have it. I wasn't impressed with stock TouchWiz (4.1 I believe?) I have been switching between TW based and AOSP roms alot. I just never found the rom I liked. All of them began to run slow, if they were not already slow. (I do not blame any of the roms I have used, I want to point that out)
Recently I sent the phone back for repair, because it had a burnt in screen. So I went ahead and flashed full stock and reset the counter and all the fun stuff. When I rebooted the phone (100% clean wipe, flashed a Netherlands rom) I noticed that the phone was slow as living h*ll. I had flashed it to a "out off the box" experience but the phone was just about useless. I went ahead and flashed a different Netherlands rom, which was a tad bit faster. I went with it and sent it back.
When I received the phone back in my mailbox, they had flashed stock again (why would one flash stock if just the screen had to be replaced?). I noticed that the phone was extremely slow again!
I decided to believe that it was TW to blame, and flashed Omni KitKat. This was fine for about a week, after which the phone would randomly lock up and system.apk began to crash every 30 minutes or so.
I then decided to start with a clean plate and flashed CM11 (full wipe, including media and all). I have been using that for a little over 2 months now, but the same issues are starting to occur. I have tried it without any 3rd party apps installed, without success. The phone locks up about every 5 minutes with the screen on, I can't listen to music (Google Music or PowerAMP) and then switch to another app, because the music will then stop. If I press the home button, there is an 3-10 second delay, after which system.apk decides to reload along with the launcher (Google Now Launcher), things like that. Sounds like a memory problem to me.
I think it might have something to do with a baseband issue, because of the fact that I have had problems similar before, which were (sort of) solved by flashing a different baseband. But I don't think that Sammy's basebands are compatible with CM11, and I have yet to come across a problem with a CM11 baseband on the internet.
Do any of you experts know an explanation to my problem? Would you suggest sending the phone back for repair?
Thanks in advance
Click to expand...
Click to collapse
The problem might occur because of memory which one of my friend had earlier. Can you tell me how long copying files into phone storage takes?? Do you feel like ROMs are geting installed slowly than previous, slow copying of files?
ASOP Roms like CM never come with baseband. they use the same baseband that you already have in your phone. Only Stock based comes with baseband in their firmware. Sometimes(not most of the time) it can be if you are using different baseband than the one of the firmware, like if you have 4.1.2 and installed baseband of older version like of 4.1.1 but this is exceptional..
Thanks for your reply!
I don't think the internal sd has gotten slower tbh. I tried to copy an 2gb dummy bin from the extsd to my infernal sd, which copied with an average speed of 9mb/s.
I have tried experimenting with different TW based roms in the past, so I might still have a wrong baseband / ril. Is there a way of checking this?
Sent from my GT-I9300 using XDA Free mobile app

[Q] All 4.4/4.3 roms constant reboot

Hello friends,
I recently picked up an i717 and am in the process of sorting it out. It was originally a Bell phone, though of course it's unlocked these days. I've been hacking at various Android phones for years now and have managed to work through just about everything, but this has me stumped...
I've tried almost all the 4.4 roms, and most of the 4.3 as well. I've tried various kernels/modems/combinations/etc. I've used CWM and TWRP. They all invariably lead to the phone either rebooting constantly from the "optimizing apps" dialogue, or a few times I've made it to the welcome screen, but it's always just up for a minute or two, crashes, then reboots. I haven't found a live download for 4.2 yet, so I don't know if it would work or not. 4.1 stock and Padawan run just great. I've been doing multiple full wipes before installation, flashing the rom a few times, then hitting the caches a few more times for good measure. I can't imagine my flashing technique being at issue here.
I do know that there is at least some physical damage to the phone. The capacitive buttons don't work. But it doesn't see immediately obvious to me that these would be related. Of course, I've seen stranger things. Running Padawan the phone will hum right along at max speed all day with no apparent issues, so that side of the hardware seems okay.
Sometimes CM roms will end up at the CM welcome screen and pop up a "com.android.acore has stopped" dialogue. But the constant reboots are there on every rom I've tried.
Does anybody have any ideas?
Outside of the, every once in a while you just need to go all the way back to stock just to make sure all the garbage is taken out, have you considered the infamous stuck power button?
Though I have yet to, many have experience the stuck power button. It may feel ok and you may even hear it click, but that doesnt mean anything. Give your phone a couple good flicks to the back behind the button. Though it does seem odd that it would run one rom without issue and not others, but it is worth a shot.
Again taking your phone to 100% stock every blue moon or so can be a good remedy too.
Keep us posted. We can work you through this.
Sent from my SAMSUNG-SGH-I527 using XDA Free mobile app
I thought about the power button issue. However, it proceeds to boot into the OS until after a time when the screen locks then reboot, which would seem too long to be the power button in any case. Regardless, a few sharp flicks didn't help much. And, of course, it runs quite happily all day long running on 4.1.
I have restored to stock JB, though admittedly not earlier than that. I guess I could try going all the way back to GB to see if that makes any difference.
In my experimentation tonight I've found that 4.2 also does not work, while I can add 4.1 non-tw roms to the working list. My best guess seems like something about one of the many under-the-hood things that changed with 4.2 doesn't get along with something about my particular phone. But, who knows.
For now I'll try rolling back to GB in Odin and see where that gets me.
I would say ICS is about as far back as you need. Recently I was having issue getting anything 4.3 and up to work or even flash. No different recoveries had effect either.
Wiped slate clean and started over from ICS, and Bob was my uncle. Everything that failed before was not an issue. Running latest 4.4 now and might I say "Orgasmic"
Sent from my SAMSUNG-SGH-I527 using XDA Free mobile app
Ahh, if only I were on 4.4 on my Note, life would be good Though, to be honest, I'm quite digging this thing, even at 4.1.
Last night I rolled back to GB, and had no luck. Although the Odin tar that I found apparently didn't include recovery, so that had to be flashed separately. I don't know if that might make a difference. That might be my experiment for tonight if I can find a tar that includes everything. Might be easier to find on ICS.
Just running my mind through other stuff I've thought of, I remember reading about kitkat having some issues with SD cards, so I've mostly been experimenting with the card pulled and a fresh format on the internal storage, with no real difference. Tried safe mode, no dice (not that I would expect this to make a difference on a fresh flash, but who knows lol...).
It's just such a weird thing. It boots into the OS with seemingly no issues. On occasions when I can actually get to the lock screen, everything runs fluid as can be until it freezes and reboots. Sometimes when it gets stuck at the 'optimizing' screen it'll just restart the count every boot, sometimes the number of apps to be done go down each time until there are 3-4 left which persist through each reboot.
I wonder if I could check logcat via adb before it reboots. Might be able to find some clues there.
Here's a factory firmware image of 4.1.2 to be flashed with Odin.
http://www.mediafire.com/view/g7gn29h7nu63id5
I've used this to revert many times. Install it. Run it once, then factory reset and run it for at least a few hours. If you experience issues you probably have hardware failure. If you don't have issues you can proceed with installing the latest clockwork mod recovery. Then wipe system and internal memory 3 times with recovery. Now flash the zip of your favorite kit Kat rom. Reboot and run it. Then factory reset and hopefully run it forever! If you're on a kit Kat build and experience sd card issues, there's an xposed module that might be able to help with that.
Thanks a lot, Bro. I'm downloading the image right now and will flash it then give it some time to settle in. Fingers will be crossed!
Just to give you guys an update, I flashed that stock image, ran it that way for a day, then attempted a few different 4.4 roms. Still no lock.
But thanks for the ideas so far!
I guess it's not the worst thing in the world. At least it runs 4.1 like a top.
Bassism said:
Just to give you guys an update, I flashed that stock image, ran it that way for a day, then attempted a few different 4.4 roms. Still no lock.
But thanks for the ideas so far!
I guess it's not the worst thing in the world. At least it runs 4.1 like a top.
Click to expand...
Click to collapse
Have you tried to turn on USB Debugging and run "adb logcat" to see what errors are causing the problem? If it is an optional program or hardware feature you may be able to disable it and run the newer ROMs. I know bluetooth has been an ongoing pain point for people. Which modem are you running? I know that some of the older modems do not work with the newer ROMS.
Good luck.
Brett
corrupt radio
i had the same issue, flashed 4.4.4 and ran like a charm for 1 day them the radio took a dump. downgraded and worked for another day.
imei became unknown and the no radios were able to fix this. went as far back as 2.3.6 hoping my radios would be fixed and no dice.i have tried endless for weeks to fix my phone and seems doomed.
none of the bricked threads helped and flashing stock with odin is no help. there seems to be no fix to the null imei and unknown baseband

Categories

Resources